Ordering number : ENA1996 LV8417CS Bi-CMOS IC Forward/Reverse Motor Driver Overview The LV8417CS is a 1-channel H bridge motor driver IC. The package size is extremely small with wafer level package (WLP). Moreover, the on-resistance is low (upper and lower total 0.27Ω typ.). The application voltage range is wide (2.0V to 10.5V). The H bridge of this IC is P-N composition and thereby reduces the external parts without need of charge pump. Therefore, LV8417CS realizes reduction of mounting area which enables lower cost and smaller application size. Functions • H-bridge 1-channel forward/reverse motor driver • IO max=1.0A (t≤100ms 2.0A, t≤10ms 3.8A) • BiCDMOS process • Built-in low voltage reset and thermal shutdown circuit • Output ON resistance (Upper and lower total 0.27Ω; Ts=25°C, IO=1.0A) Specifications Maximum Ratings at Ta = 25°C, SGND = PGND = 0V Parameter Symbol Power supply voltage (for load) VM max Power supply voltage (for control) VCC max Conditions Ratings Unit -0.5 to 12.6 V -0.5 to 6.0 V 1.0 A Output current IO max Output peak current IO peak1 t ≤ 100ms 2.0 A IO peak2 t ≤ 10ms 3.8 A Input voltage VIN max Allowable power dissipation Pd max -0.5 to VCC+0.5 Operating temperature Topr -20 to +85 °C Storage temperature Tstg -55 to +150 °C Mounted on a specified board * 850 V mW * Specified board : 57mm × 57mm × 1.6mm, glass epoxy both side board. Caution 1) Absolute maximum ratings represent the value which cannot be exceeded for any length of time. Caution 2) Even when the device is used within the range of absolute maximum ratings, as a result of continuous usage under high temperature, high current, high voltage, or drastic temperature change, the reliability of the IC may be degraded. Please contact us for the further details. Any and all SANYO Semiconductor Co.,Ltd. products described or contained herein are, with regard to "standard application", intended for the use as general electronics equipment. The products mentioned herein shall not be intended for use for any "special application" (medical equipment whose purpose is to sustain life, aerospace instrument, nuclear control device, burning appliances, transportation machine, traffic signal system, safety equipment etc.) that shall require extremely high level of reliability and can directly threaten human lives in case of failure or malfunction of the product or may cause harm to human bodies, nor shall they grant any guarantee thereof. If you should intend to use our products for new introduction or other application different from current conditions on the usage of automotive device, communication device, office equipment, industrial equipment etc. , please consult with us about usage condition (temperature, operation time etc.) prior to the intended use. If there is no consultation or inquiry before the intended use, our customer shall be solely responsible for the use. Specifications of any and all SANYO Semiconductor Co.,Ltd. products described or contained herein stipulate the performance, characteristics, and functions of the described products in the independent state, and are not guarantees of the performance, characteristics, and functions of the described products as mounted in the customer's products or equipment. To verify symptoms and states that cannot be evaluated in an independent device, the customer should always evaluate and test devices mounted in the customer ' s products or equipment. D0711 SY 20111012-S00003 No.A1996-1/5 LV8417CS Allowable Operating Conditions at Ta = 25°C, SGND = PGND = 0V Parameter Symbol Conditions Ratings Unit Power supply voltage (VM pin) VM 2.0 to 10.5 Power supply voltage (VCC pin) VCC 2.7 to 5.5 V Input signal voltage VIN 0 to VCC V Input signal frequency f max Duty = 50% 200 V kHz Electrical Characteristics Ta = 25°C, VCC = 3.0V, VM = 6.0V, SGND = PGND = 0V Parameter Symbol Conditions Remarks Ratings min typ max Unit 1.0 μA 120 μA 1.0 μA 0.8 mA Standby load current drain IMO ENA = 0V 1 Operating load current drain IM1 ENA = 3.0V, No load 3 Standby control current drain ICO ENA = IN1 = IN2 = 0V 2 Operating current consumption 1 IC1 ENA = 3.0V, No load 3 High-level input voltage VIH 2.7 ≤ VCC ≤ 5.5V 0.6×VCC VCC V Low-level input voltage VIL 2.7 ≤ VCC ≤ 5.5V 0 0.2×VCC V High-level input current IIH1 VIN = 3V 30 μA IIL1 VIN = 0V Pull-down resistance value RDN ENA, IN1, IN2 4 Output ON resistance RON Sum of top and bottom sides ON resistance. 5 Low-voltage detection operating VCS1 VCC pin voltage 6 VCS2 VCC pin voltage Thermal shutdown temperature Tth Output Turn-on time TPLH block Output response TIOH 80 0.5 20 (ENA,IN1, IN2) Low-level input current μA -1.0 (ENA,IN1, IN2) 100 200 400 kΩ 0.27 0.4 Ω 2.1 2.3 2.5 V 6 2.3 2.5 2.7 V Design guarantee * 7 150 180 210 °C No load 8 0.10 0.15 μs No load, Design guarantee * 9 0.23 0.35 μs voltage Low-voltage detection release voltage time H Turn-off time TPHL No load 8 0.10 0.15 μs Output response TIOL No load, Design guarantee * 9 0.25 0.38 μs time L Remarks 1. Current consumption when output at the VM pin is off. 2. Current consumption at the VCC pin when in all function stop. 3. Current consumption at the VCC pin when ENA=3V(IC starting time). 4. ENA, IN1 and IN2 pin have an internal pull-down resistor. 5. The saturation voltage of the bottom above an OUT pin is added, and the value broken by the current value is shown. 6. All output transistors are turned off if a low-voltage is detected for VCC. 7. All output transistors are turned off if the thermal protection circuit is activated. They are turned on again as the temperature goes down. 8. Rising time from 10 to 90% and falling time from 90 to 10% are specified. 9. Time until it changes OUT pin voltage 10% from the time of change of input pin voltage being 50% of VCC is specified. IN 50% 50% 90% 90% OUT 10% 10% TIOH TPLH TIOL TPHL No.A19965-2/5 LV8417CS Package Dimensions unit : mm (typ) 3418 SIDE VIEW BOTTOM VIEW 0.235 TOP VIEW Allowable power dissipation, Pd max -- W 2 0.5 C B 1.47 3 1 0.27 0.235 0.55 MAX 0.08 (0.42) 0.5 SIDE VIEW Pd max -- Ta 1.5 A 1.47 Specified board: 57×57×1.6mm3 glass epoxy both side board. 1.0 0.85 0.5 0.44 0 -20 SANYO : WLP9(1.47X1.47) 0 20 40 60 80 85 100 Ambient temperature, Ta -- C Pin Assignment Ball side view Top view A B C OUT2 PGND OUT1 2 VM SGND VCC 3 IN2 IN1 ENA C A B 0.5mm 1 OUT1 PGND OUT2 VCC SGND VM ENA IN1 IN2 1.47mm 0.5mm 1 2 3 1.47mm Block Diagram VCC + - VM Thermal protection circuit Output pre stage ENA IN2 - OUT1 Low voltage protection circuit IN1 + Starting control block OUT2 Motor control logic PGND SGND No.A19965-3/5 LV8417CS Pin Functions Pin No. Pin name C-3 ENA Logic enable pin B-3 IN1 Driver output change pin A-3 IN2 Driver output change pin C-2 VCC SGND Power supply for control B-2 Description Equivalent circuit VCC ENA/IN1/IN2 Ground pin for control SGND Power supply for load A-2 VM C-1 OUT1 Driver output pin A-1 OUT2 Driver output pin B-1 PGND Ground pin for load VM OUT2 OUT1 PGND Truth Table ENA L H IN1 IN2 OUT1 OUT2 Mode All function stop - - Z Z L L Z Z Standby H L H L Forward L H L H Reverse H H L L Brake - : denotes a don't care value. Z : High-impedance • Current drain is zero in all function stop mode. • All power transistors turn off and the motor stops driving when the IC is detected in low voltage or thermal protection mode. No.A19965-4/5 LV8417CS Sample Application Circuit Motor connect pin OUT1 OUT2 OUT1 PGND OUT2 VCC SGND VM ENA IN1 IN2 SW2 SW1 SW3 VCC (Power pin for control) VM (Power pin for loads) VIN (Power pin for switch) ENA IN1 IN2 Logic input pin * Connect a kickback absorbing capacitor as close as possible to the IC. Characteristics deterioration of the IC or damage may result if an instantaneous voltage surge exceeding the maximum rated value is applied to the VM line due to coil kickback or other causes. SANYO Semiconductor Co.,Ltd. assumes no responsibility for equipment failures that result from using products at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges, or other parameters) listed in products specifications of any and all SANYO Semiconductor Co.,Ltd. products described or contained herein. SANYO Semiconductor Co.,Ltd. strives to supply high-quality high-reliability products, however, any and all semiconductor products fail or malfunction with some probability. It is possible that these probabilistic failures or malfunction could give rise to accidents or events that could endanger human lives, trouble that could give rise to smoke or fire, or accidents that could cause damage to other property. When designing equipment, adopt safety measures so that these kinds of accidents or events cannot occur. Such measures include but are not limited to protective circuits and error prevention circuits for safe design, redundant design, and structural design. In the event that any or all SANYO Semiconductor Co.,Ltd. products described or contained herein are controlled under any of applicable local export control laws and regulations, such products may require the export license from the authorities concerned in accordance with the above law. No part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying and recording, or any information storage or retrieval system, or otherwise, without the prior written consent of SANYO Semiconductor Co.,Ltd. Any and all information described or contained herein are subject to change without notice due to product/technology improvement, etc. When designing equipment, refer to the "Delivery Specification" for the SANYO Semiconductor Co.,Ltd. product that you intend to use. Upon using the technical information or products described herein, neither warranty nor license shall be granted with regard to intellectual property rights or any other rights of SANYO Semiconductor Co.,Ltd. or any third party. SANYO Semiconductor Co.,Ltd. shall not be liable for any claim or suits with regard to a third party's intellctual property rights which has resulted from the use of the technical information and products mentioned above. This catalog provides information as of December, 2011. Specifications and information herein are subject to change without notice. PS No.A1996-5/5