Ordering number : ENA1888 Bi-CMOS IC LV8402V 2ch Forward/Reverse Motor Driver Overview LV8402T is a 2ch forward/reverse motor driver IC using D-MOS FET for output stage. As MOS circuit is used, it supports the PWM input. Its features are that the on resistance (0.75Ω typ) and current dissipation are low. It also provides protection functions such as heat protection circuit and reduced voltage detection and is optimal for the motors that need high-current. Functions • 2ch forward/reverse motor driver. • Low power consumption. • Low-temperature resistance 0.75Ω. • Built-in low voltage reset and thermal shutdown circuit. • 3 mode function forward/reverse, brake. • Built-in charge pump. Specifications Maximum Ratings at Ta = 25°C, SGND = PGND = 0V Parameter Symbol Power supply voltage (for load) VM max Power supply voltage (for control) VCC max Output current IO max Output peak current IO peak Conditions Ratings Unit -0.5 to 16.0 t ≤ 10ms V -0.5 to 6.0 V 1.4 A 2.5 A Input voltage VIN max Allowable power dissipation Pd max -0.5 to VCC+0.5 Operating temperature Topr -20 to +85 °C Storage temperature Tstg -55 to +150 °C Mounted on a specified board* 800 V mW * Specified board : 114.3mm × 76.1mm × 1.6mm, glass epoxy board. Any and all SANYO Semiconductor Co.,Ltd. products described or contained herein are, with regard to "standard application", intended for the use as general electronics equipment (home appliances, AV equipment, communication device, office equipment, industrial equipment etc.). The products mentioned herein shall not be intended for use for any "special application" (medical equipment whose purpose is to sustain life, aerospace instrument, nuclear control device, burning appliances, transportation machine, traffic signal system, safety equipment etc.) that shall require extremely high level of reliability and can directly threaten human lives in case of failure or malfunction of the product or may cause harm to human bodies, nor shall they grant any guarantee thereof. If you should intend to use our products for applications outside the standard applications of our customer who is considering such use and/or outside the scope of our intended standard applications, please consult with us prior to the intended use. If there is no consultation or inquiry before the intended use, our customer shall be solely responsible for the use. Specifications of any and all SANYO Semiconductor Co.,Ltd. products described or contained herein stipulate the performance, characteristics, and functions of the described products in the independent state, and are not guarantees of the performance, characteristics, and functions of the described products as mounted in the customer' s products or equipment. To verify symptoms and states that cannot be evaluated in an independent device, the customer should always evaluate and test devices mounted in the customer' s products or equipment. D0110 SY 20101025-S00002 No.A1888-1/6 LV8402V Allowable Operating Conditions at Ta = 25°C, SGND = PGND = 0V Parameter Symbol Conditions Ratings Unit Power supply voltage (VM pin) VM Power supply voltage (VCC pin) VCC 1.5 to 15.0 2.8 to 5.5 V Input signal voltage VIN 0 to VCC V Input signal frequency f max 200 V kHz Electrical Characteristics Ta = 25°C, VCC = 3.0V, VM = 6.0V, SGND = PGND = 0V, unless otherwise specified. Parameter Symbol Conditions Ratings Remarks min Standby load current drain IMO VCC = 0V, VM = 6V 1 Operating control current drain IC1 When VCC is applied, with no load 2 High-level input voltage VIH 2.7 ≤ VCC ≤ 5.5V Low-level input voltage VIL 2.7 ≤ VCC ≤ 5.5V High-level input current IIH VIN = 3V 3 IIL VIN = 0V 3 typ Unit max 0.85 0.6×VCC 1.0 μA 1.2 mA VCC 0 15 V 0.2×VCC V 25 μA (IN1, IN2, EN1, EN2) Low-level input current μA -1.0 (IN1, IN2, EN1, EN2) Pull-down resistance value RPD1 100 Charge pump voltage VG VCC + VM Output ON resistance 1 RON1 Sum of top and bottom sides ON Output ON resistance 2 RON2 Sum of top and bottom sides ON 8.5 200 400 kΩ 9.0 9.5 V 4 0.75 1.2 Ω 4 1.0 1.5 Ω resistance. resistance. VCC = 2.8V Low-voltage detection voltage VCS VCC pin voltage is monitored 5 2.15 2.30 2.45 V Thermal shutdown temperature Tth Design guarantee value * 6 150 180 210 °C Output block TPLH μS Turn-on time Turn-off time TPHL When no load. Design guarantee value * 7 0.3 0.5 When no load. 8 100 200 nS When no load. Design guarantee value * 7 0.35 0.6 μS When no load. 8 100 200 nS * : Design guarantee value and no measurement is preformed. Remarks 1. Current consumption when output at the VM pin is off. 2. Current consumption at the VCC pin when VCC is 3V(standby mode). 3. Pins IN 1, 2, EN1, and EN2 are all pulled down. 4. Sum of upper and lower saturation voltages of OUT pin divided by the current. 5. All power transistors are turned off if a low VCC condition is detected. 6. All output transistors are turned off if the thermal protection circuit is activated. They are turned on again as the temperature goes down. 7. Rising time from 10 to 90% and falling time from 90 to 10% are specified. 8. The change of the voltage of the input pin provides for time until the voltage of the terminal OUT changes by 10% at the time of 50% of VCC. No.A1888-2/6 LV8402V Package Dimensions unit : mm (typ) 3178B Allowable power dissipation, Pd max -- W 0.5 6.4 9 4.4 16 1 8 0.65 0.15 0.22 1.5max (0.33) Pd max -- Ta 1 5.2 Specified board : 114.3×76.1×1.6mm3 glass epoxy 0.8 0.6 0.42 0.4 0.2 0 (1.3) 0 20 40 60 80 85 100 0.1 Ambient temperature, Ta -- C SANYO : SSOP16(225mil) Pin Assignment VG 1 16 C1H VM 2 15 C1L OUT1 3 PGND 5 LV8402V OUT2 4 14 SGND 13 EN1 12 IN1 OUT3 6 11 VCC OUT4 7 10 EN2 9 IN2 VM 8 Top view No.A1888-3/6 LV8402V Block Diagram VCC VM Thermal Protection Circuit Startup control block OUT1 OUT2 Reducedvoltage protection circuit VM EN1 EN2 OUT3 Motor control logic IN1 OUT4 IN2 PGND Charge pump VCC+VM C1H C1L VG SGND * Connect a kickback absorption capacitor as near as possible to the IC. Coil kickback may cause increase in VM line voltage, and a voltage exceeding the maximum rating may be applied momentarily to the IC, which results in deterioration or damage of the IC Truth Table IN1 IN2 OUT1 OUT2 (EN1) (EN2) (OUT3) (OUT4) H H L H Reverse L H L Forward - L L L Charge pump Mode Brake - : denotes a don't care value. • The charge pump is always activated as long as VCC is applied. * All power transistors turn off and the motor stops driving when the IC is detected in low voltage or thermal protection mode. No.A1888-4/6 LV8402V Pin Functions Pin No. Pin name 16 C1H 1 VG Description Equivalent circuit Step-up capacitor connection pin. VG C1H 12 IN1 Driver output switching. 9 IN2 Logic enable pin. 13 EN1 (Pull-down resistor incorporated) 10 EN2 3 OUT1 4 OUT2 6 OUT3 7 OUT4 VCC Driver output. VM OUT OUT PGND 2 VM Motor block power supply. 11 VCC Logic block power supply. 14 SGND Control block ground. 5 PGND Driver block ground. 8 No.A1888-5/6 LV8402V SANYO Semiconductor Co.,Ltd. assumes no responsibility for equipment failures that result from using products at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges, or other parameters) listed in products specifications of any and all SANYO Semiconductor Co.,Ltd. products described or contained herein. SANYO Semiconductor Co.,Ltd. strives to supply high-quality high-reliability products, however, any and all semiconductor products fail or malfunction with some probability. It is possible that these probabilistic failures or malfunction could give rise to accidents or events that could endanger human lives, trouble that could give rise to smoke or fire, or accidents that could cause damage to other property. When designing equipment, adopt safety measures so that these kinds of accidents or events cannot occur. Such measures include but are not limited to protective circuits and error prevention circuits for safe design, redundant design, and structural design. In the event that any or all SANYO Semiconductor Co.,Ltd. products described or contained herein are controlled under any of applicable local export control laws and regulations, such products may require the export license from the authorities concerned in accordance with the above law. No part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying and recording, or any information storage or retrieval system, or otherwise, without the prior written consent of SANYO Semiconductor Co.,Ltd. Any and all information described or contained herein are subject to change without notice due to product/technology improvement, etc. When designing equipment, refer to the "Delivery Specification" for the SANYO Semiconductor Co.,Ltd. product that you intend to use. Information (including circuit diagrams and circuit parameters) herein is for example only; it is not guaranteed for volume production. Upon using the technical information or products described herein, neither warranty nor license shall be granted with regard to intellectual property rights or any other rights of SANYO Semiconductor Co.,Ltd. or any third party. SANYO Semiconductor Co.,Ltd. shall not be liable for any claim or suits with regard to a third party's intellctual property rights which has resulted from the use of the technical information and products mentioned above. This catalog provides information as of December, 2010. Specifications and information herein are subject to change without notice. PS No.A1888-6/6