WIREWOUND CHIP INDUCTORS SCI1008S SERIES 1. PART NO. EXPRESSION : SCI1008S-5N6KF (a) (b) (c) (d) (e) (f) (a) Series code (d) Inductance code : 5N6 = 5.6nH (b) Dimension code (e) Tolerance code : G = ±2%, J = ±5%, K = ±10% (c) Type code : S ( Standard ) (f) F : RoHS Compliant 2. CONFIGURATION & DIMENSIONS : C B D J I I H F G A F E PCB Pattern Unit:m/m A B C 2.92 Max. 2.79 Max. 2.03 Max. D E F G H I J 0.65 Ref. 2.03 Ref. 0.51 Ref. 1.52 Ref. 2.54 Ref. 1.02 Ref. 1.27 Ref. 3. SCHEMATIC : 4. MATERIALS : a (a) Core : Ceramic U core (b) Wire : Enamelled Copper Wire b (c) Terminal Metallization : Ag + Ni + Au c NOTE : Specifications subject to change without notice. Please check our website for latest information. 22.06.2010 SUPERWORLD ELECTRONICS (S) PTE LTD PG. 1 WIREWOUND CHIP INDUCTORS SCI1008S SERIES 5. GENERAL SPECIFICATION : a) Storage temp. : -25°C to +80°C b) Operating temp. : -40°C to +125°C c) Temperature rise : 40°C Max. d) Rated current : Base on temp. rise & ǻL/L0A=10% Max. e) Resistance to solder heat : 260°C.10sec 6. ELECTRICAL CHARACTERISTICS : Part No. Tolerance Available L ( nH ) Test Freq ( MHz ) Q Min. Q Test Freq ( MHz ) SRF ( MHz ) Min. DCR (ȍ) Max. IDC ( mA ) Max. SCI1008S-5N6 F K, J 5.6 50 50 1500 4000 0.150 1000 SCI1008S-10N F K, J, G 10 50 50 500 4100 0.080 1000 SCI1008S-12N F K, J, G 12 50 50 500 3300 0.090 1000 SCI1008S-15N F K, J, G 15 50 50 500 2500 0.110 1000 SCI1008S-18N F K, J, G 18 50 50 350 2400 0.120 1000 SCI1008S-22N F K, J, G 22 50 55 350 2400 0.120 1000 SCI1008S-24N F K, J, G 24 50 55 350 1900 0.120 1000 SCI1008S-27N F K, J, G 27 50 55 350 1600 0.130 1000 SCI1008S-33N F K, J, G 33 50 60 350 1600 0.140 1000 SCI1008S-39N F K, J, G 39 50 60 350 1500 0.150 1000 SCI1008S-47N F K, J, G 47 50 65 350 1500 0.160 1000 SCI1008S-56N F K, J, G 56 50 65 350 1300 0.180 1000 SCI1008S-62N F K, J, G 62 50 65 350 1250 0.200 1000 SCI1008S-68N F K, J, G 68 50 65 350 1300 0.200 1000 SCI1008S-75N F K, J, G 75 50 60 350 1100 0.210 1000 SCI1008S-82N F K, J, G 82 50 60 350 1000 0.220 1000 SCI1008S-R10 F K, J, G 100 25 60 350 1000 0.560 650 SCI1008S-R12 F K, J, G 120 25 60 350 950 0.630 650 SCI1008S-R15 F K, J, G 150 25 45 100 850 0.700 580 SCI1008S-R18 F K, J, G 180 25 45 100 750 0.770 620 SCI1008S-R22 F K, J, G 220 25 45 100 700 0.840 500 SCI1008S-R24 F K, J, G 240 25 45 100 650 0.880 500 SCI1008S-R27 F K, J, G 270 25 45 100 600 0.910 500 NOTE : Specifications subject to change without notice. Please check our website for latest information. 22.06.2010 SUPERWORLD ELECTRONICS (S) PTE LTD PG. 2 WIREWOUND CHIP INDUCTORS SCI1008S SERIES 6. ELECTRICAL CHARACTERISTICS : Part No. Tolerance Available L ( nH ) Test Freq ( MHz ) Q Min. Q Test Freq ( MHz ) SRF ( MHz ) Min. DCR (ȍ) Max. IDC ( mA ) Max. SCI1008S-R30 F K, J, G 300 25 45 100 585 1.00 450 SCI1008S-R33 F K, J, G 330 25 45 100 570 1.05 450 SCI1008S-R36 F K, J, G 360 25 45 100 530 1.10 470 SCI1008S-R39 F K, J, G 390 25 45 100 500 1.12 470 SCI1008S-R43 F K, J, G 430 25 45 100 480 1.15 470 SCI1008S-R47 F K, J, G 470 25 45 100 450 1.19 470 SCI1008S-R56 F K, J, G 560 25 45 100 415 1.33 400 SCI1008S-R62 F K, J, G 620 25 45 100 375 1.40 300 SCI1008S-R68 F K, J, G 680 25 45 100 375 1.47 400 SCI1008S-R75 F K, J, G 750 25 45 100 360 1.54 360 SCI1008S-R82 F K, J, G 820 25 45 100 350 1.61 400 SCI1008S-R91 F K, J, G 910 25 35 50 320 1.68 380 SCI1008S-1R0 F K, J, G 1000 25 35 50 290 1.75 370 SCI1008S-1R2 F K, J, G 1200 7.96 35 50 250 2.00 310 SCI1008S-1R5 F K, J, G 1500 7.96 28 50 200 2.30 330 SCI1008S-1R8 F K, J, G 1800 7.96 28 50 160 2.60 300 SCI1008S-2R2 F K, J, G 2200 7.96 28 50 160 2.80 280 SCI1008S-2R7 F K, J, G 2700 7.96 22 25.2 140 3.20 290 SCI1008S-3R3 F K, J, G 3300 7.96 22 25.2 110 3.40 290 SCI1008S-3R9 F K, J, G 3900 7.96 20 25.2 100 3.60 260 SCI1008S-4R7 F K, J, G 4700 7.96 20 25.2 90 4.00 260 SCI1008S-5R6 F K, J, G 5600 7.96 16 7.96 20 4.00 240 SCI1008S-6R8 F K, J, G 6800 7.96 15 7.96 40 4.90 200 SCI1008S-8R2 F K, J, G 8200 7.96 15 7.96 25 6.00 170 SCI1008S-103 F K, J, G 10000 2.52 15 7.96 20 9.00 150 SCI1008S-123 F K, J, G 12000 2.52 15 7.96 18 10.5 130 SCI1008S-153 F K, J, G 15000 2.52 15 7.96 15 11.5 120 Inductance tolerance : : G : ±2% J : ±5% K : ±10% NOTE : Specifications subject to change without notice. Please check our website for latest information. 22.06.2010 SUPERWORLD ELECTRONICS (S) PTE LTD PG. 3 WIREWOUND CHIP INDUCTORS SCI0805S SERIES 7. PACKAGING INFORMATION : Reel Configuration : COVER TAPE EMBOSSED CARRIER P1 Ø1.5 H B F W P0 1.75±0.1 Paper Tape : A P Dimension (unit: mm) Series A B H F P P0 P1 W Qty SCI0402S 0.72 1.19 0.60 3.50 4.00 4.00 2.00 8.00 4000pcs / reel SCI0603S 1.35 1.95 0.95 3.50 4.00 4.00 2.00 8.00 4000pcs / reel NOTE : Specifications subject to change without notice. Please check our website for latest information. 22.06.2010 SUPERWORLD ELECTRONICS (S) PTE LTD PG. 4 WIREWOUND CHIP INDUCTORS SCI0805S SERIES G±0.05 Ø1.5 J±0.05 D±0.1 E±0.05 A±0.2 4±0.1 F±0.1 Embossed Carrier Tape : C±0.1 Ø1.5 B±0.1 H±0.05 Dimension (unit: mm) Series A B C D E F G H J Qty SCI0805S 8 1.85 4 2.30 3.5 1.75 2 1.45 0.23 2000pcs / reel SCI0805LP 8 1.80 4 2.30 3.5 1.75 2 0.90 0.23 2000pcs / reel SCI0805HQ 8 1.85 4 2.30 3.5 1.75 2 1.45 0.23 2000pcs / reel SCI1008S 8 2.70 4 2.80 3.5 1.75 2 2.00 0.23 2000pcs / reel SCI1008LP 8 2.70 4 2.80 3.5 1.75 2 1.50 0.23 2000pcs / reel SCI1008HQ 8 2.70 4 2.80 3.5 1.75 2 2.00 0.23 2000pcs / reel Leader/Trailer Tape : Trailer End Leader End Empty compartments with cover tape (100mm min.) Trailer (80mm min.) Cover tape only (250mm min.) Peel-off Force : Peel-off force should be in the range of 0.1N~0.7N at a peel-off speed of 300±10mm/min. Peeling Direction Top cover tape <1 0 ° Base tape NOTE : Specifications subject to change without notice. Please check our website for latest information. 22.06.2010 SUPERWORLD ELECTRONICS (S) PTE LTD PG. 5 WIREWOUND CHIP INDUCTORS SCI1008S SERIES 8. ENVIRONMENTAL CHARACTERISTICS : Electrical Performance Test : SPECIFICATION ITEM TEST CONDITIONS / TEST METHODS 1 Inductance HP4291B 2 Q HP4291B 3 SRF 4 DC Resistance Rdc Mico-Ohmmeter (GOM-801G) 5 Rated Current IDC The device should be REFLOW soldered (230±5°C for Refer to Electrcal Characteristics List HP8753D 10 seconds) to a tinned copper subs rate. A dynamiter 6 Over Load Test After test, inductors shall Applied 2 times of rated allowed DC current to inductor have no evidence of for a period of 5 minute. electrical and mechanical damage 7 Withstanding After test, inductors shall AC voltage of 500VAC applied between inductors Voltage Test have no evidence of terminal and case for 1 minute. electrical and mechanical damage 8 1000 MOhm min. Insulation 100VDC applied between inductor terminal and case Resistance Test NOTE : Specifications subject to change without notice. Please check our website for latest information. 22.06.2010 SUPERWORLD ELECTRONICS (S) PTE LTD PG. 6 WIREWOUND CHIP INDUCTORS SCI1008S SERIES Mechanical Performance Test : SPECIFICATION ITEM 1 Vibration TEST CONDITIONS / TEST METHODS Appearance : No damage Test device shall be soldered on the substrate L change : within ±5% Oscillation Frequency : 10 to 55 to 10Hz for 1 min. Q change : within ±10% Amplitude : 1.5mm Time : 2hrs for each axis (X, Y, Z), total 6hrs. 2 Resistance to Appearance : No damage Pre-heating : 150°C, 1 min Soldering Heat L change : within ±5% Solder Composition : Sn/Pb=63/67 Q change : within ±10% Solder Temperature : 230±5°C Immersion Time : 20±2sec Solder Temperature : 260±5°C Immersion Time : 5±2sec 3 Component 1 lbs. For 0402 The device should be REFLOW soldered (230±5°C for Adhesion 2 lbs. For 0603 10 seconds) to a tinned copper subs rate. A dynamiter (Push Test) 3 lbs. For the rest force gauge should be applied to the side of the conponent. The device must withstand a minimum force of 2 or 4 pounds without a failure of the termination attached to component. 3 Component The electrodes shall be at Pre-heating : 150°C, 1min Adhesion least 90% covered with new Solder Composition : Sn/Pb=63/67 (Push Test) solder coating. Solder Temperature : 230±5°C Immersion Time : 4±1sec 4 Drop Test After test, the chip inductor Drop 1 time for each face and 1 time for each corner. don't fell of broke on the Total drop 10 times. P.C.Board Drop Height : 100cm Drop Weight : 125g 5 6 The terminal should at least after fluxing (alpha 100 or equiv), inductor shall be be 90% covered with solder dipped in a melted solder bath at 232±5°C for 5 seconds. Resistance to There shall be no case of MIL-STD202F, METHOD 215D solvent test deformation change in Solderability Test appearance of obliteration of marking NOTE : Specifications subject to change without notice. Please check our website for latest information. 22.06.2010 SUPERWORLD ELECTRONICS (S) PTE LTD PG. 7 WIREWOUND CHIP INDUCTORS SCI1008S SERIES Climatic Test : SPECIFICATION ITEM 1 TEST CONDITIONS / TEST METHODS -40°C ~ +125°C Temperature Characteristics 2 Humidity Temperature : 40±2°C Resistance Relative Humidity : 90~95% Time : 96hrs ±2hrs Measured after exposure in the room condition for 2hrs 3 Low Temperature Appearance : No damage Temperature : -40±2°C Storage Test L change : within ±10% Time : 48±2hrs Q change : within ±20% Inductors are to be tested after 1 hour at room temperature. 4 One cycle : Thermal Shock Test Step Temperature (°C) Time (min) 1 -25±3 30 2 25±2 15 3 85±3 30 4 25±2 15 Total : 5 cycles 5 High Temperature Temperature : 125±2°C Storage Test Time : 48±2hrs Load : Allowed DC current 6 7 High Temperature There should be no Temperature : 85±2°C Load Life Test evidence of short of Time : 1000±12hrs open circuit. Load : Allowed DC current Humidity Load Temperature : 40±2°C Life Relative Humidity : 90~95% Time : 1000±12hrs Load : Allowed DC current NOTE : Specifications subject to change without notice. Please check our website for latest information. 22.06.2010 SUPERWORLD ELECTRONICS (S) PTE LTD PG. 8