WIREWOUND CHIP INDUCTORS SCI0805LP SERIES 1. PART NO. EXPRESSION : SCI0805LP-1N8KF (a) (b) (c) (d) (e)(f) (a) Series code (d) Inductance code : 1N8 = 1.8nH (b) Dimension code (e) Tolerance code : G = ±2%, J = ±5%, K = ±10% (c) Type code : LP ( Low Profile ) (f) F : Lead Free 2. CONFIGURATION & DIMENSIONS : C B E D F I F H G A J I PCB Pattern Unit:m/m A 2.29 Max. B C 1.73 Max. 1.03 Max. D E F G H I J 0.51 Ref. 1.27 Ref. 0.44 Ref. 1.02 Ref. 1.78 Ref. 1.02 Ref. 0.76 Ref. 3. SCHEMATIC : 4. MATERIALS : a (a) Core : Ceramic U core (b) Wire : Enamelled Copper Wire b (c) Terminal Metallization : Ag + Ni + Au c NOTE : Specifications subject to change without notice. Please check our website for latest information. 15.01.2008 SUPERWORLD ELECTRONICS (S) PTE LTD PG. 1 WIREWOUND CHIP INDUCTORS SCI0805LP SERIES 5. GENERAL SPECIFICATION : a) Storage temp. : -25°C to +80°C b) Operating temp. : -40°C to +125°C c) Temperature rise : 40°C Max. d) Rated current : Base on temp. rise & ǻL/L0A=10% Max. e) Resistance to solder heat : 260°C.10sec 6. ELECTRICAL CHARACTERISTICS : Part No. Tolerance Available L ( nH ) Test Freq ( MHz ) Q Min. Q Test Freq ( MHz ) SRF ( MHz ) Min. DCR (ȍ) Max. IDC (mA) Max. SCI0805LP-1N8 F K 1.8 250 55 1500 9400 0.030 800 SCI0805LP-3N9 F K, J 3.9 250 50 1000 6100 0.060 800 SCI0805LP-4N7 F K, J 4.7 250 50 1000 5500 0.060 800 SCI0805LP-6N8 F K, J 6.8 250 50 1000 5500 0.080 800 SCI0805LP-8N2 F K, J 8.2 250 50 1000 4800 0.080 800 SCI0805LP-10N F K, J, G 10 250 55 750 3300 0.080 800 SCI0805LP-12N F K, J, G 12 250 55 750 3800 0.100 800 SCI0805LP-15N F K, J, G 15 250 50 500 2950 0.100 800 SCI0805LP-18N F K, J, G 18 250 50 500 3100 0.130 800 SCI0805LP-22N F K, J, G 22 250 50 500 2900 0.150 800 SCI0805LP-27N F K, J, G 27 250 50 500 2450 0.230 600 SCI0805LP-33N F K, J, G 33 250 50 500 2350 0.280 600 SCI0805LP-39N F K, J, G 39 250 50 500 2200 0.330 600 SCI0805LP-47N F K, J, G 47 200 50 500 2000 0.390 600 SCI0805LP-56N F K, J, G 56 200 50 500 1850 0.390 500 SCI0805LP-68N F K, J, G 68 200 50 500 1500 0.400 500 SCI0805LP-82N F K, J, G 82 150 50 500 1500 0.440 500 SCI0805LP-R10 F K, J, G 100 150 50 500 1200 0.640 400 SCI0805LP-R12 F K, J, G 120 150 40 250 1150 0.680 300 SCI0805LP-R15 F K, J, G 150 150 40 250 1050 0.800 300 SCI0805LP-1R0 F K, J, G 1000 25 16 50 80 2.000 220 Inductance tolerance : : G : ±2% J : ±5% K : ±10% NOTE : Specifications subject to change without notice. Please check our website for latest information. 15.01.2008 SUPERWORLD ELECTRONICS (S) PTE LTD PG. 2 WIREWOUND CHIP INDUCTORS SCI0805LP SERIES 7. PACKAGING INFORMATION : CONFIGURATTION : COVER TAPE G±0.05 Ø1.5 1±0.05 D±0.1 E±0.05 A±0.2 4±0.1 F±0.1 EMBOSSED CARRIER C±0.1 Ø1.5 B±0.1 H±0.05 DIMENSION (unit: mm) SERIES A B C D E F G H I SCI0402 8.0 0.71 2.0 1.16 3.5 1.75 0 0.65 0.23 SCI0603 8.0 1.10 4.0 1.75 3.5 1.75 2 1.15 0.25 SCI0805 8.0 1.88 4.0 2.38 3.5 1.75 2 1.48 0.20 SCI1008 8.0 2.73 4.0 2.88 3.5 1.75 2 2.33 0.20 PACKING QUANTITY INNER REEL SERIES Q'TY (PCS) SCI0402 4000 SCI0603 4000 SCI0805 2000 SCI1008 2000 NOTE : Specifications subject to change without notice. Please check our website for latest information. 15.01.2008 SUPERWORLD ELECTRONICS (S) PTE LTD PG. 3 WIREWOUND CHIP INDUCTORS SCI0805LP SERIES 8. ENVIRONMENTAL CHARACTERISTICS : Electrical Performance Test : ITEM SPECIFICATION TEST CONDITIONS / TEST METHODS 1 Inductance HP4291B 2 Q HP4291B 3 SRF 4 DC Resistance Rdc Mico-Ohmmeter (GOM-801G) 5 Rated Current IDC The device should be REFLOW soldered (230±5°C for Refer to Electrcal Characteristics List HP8753D 10 seconds) to a tinned copper subs rate. A dynamiter 6 Over Load Test After test, inductors shall Applied 2 times of rated allowed DC current to inductor have no evidence of for a period of 5 minute. electrical and mechanical damage 7 Withstanding After test, inductors shall AC voltage of 500VAC applied between inductors Voltage Test have no evidence of terminal and case for 1 minute. electrical and mechanical damage 8 1000 MOhm min. Insulation 100VDC applied between inductor terminal and case Resistance Test NOTE : Specifications subject to change without notice. Please check our website for latest information. 15.01.2008 SUPERWORLD ELECTRONICS (S) PTE LTD PG. 4 WIREWOUND CHIP INDUCTORS SCI0805LP SERIES Mechanical Performance Test : ITEM 1 SPECIFICATION Vibration TEST CONDITIONS / TEST METHODS Appearance : No damage Test device shall be soldered on the substrate L change : within ±5% Oscillation Frequency : 10 to 55 to 10Hz for 1 min. Q change : within ±10% Amplitude : 1.5mm Time : 2hrs for each axis (X, Y, Z), total 6hrs. 2 Resistance to Appearance : No damage Pre-heating : 150°C, 1 min Soldering Heat L change : within ±5% Solder Composition : Sn/Pb=63/67 Q change : within ±10% Solder Temperature : 230±5°C Immersion Time : 20±2sec Solder Temperature : 260±5°C Immersion Time : 5±2sec 3 Component 1 lbs. For 0402 The device should be REFLOW soldered (230±5°C for Adhesion 2 lbs. For 0603 10 seconds) to a tinned copper subs rate. A dynamiter (Push Test) 3 lbs. For the rest force gauge should be applied to the side of the conponent. The device must withstand a minimum force of 2 or 4 pounds without a failure of the termination attached to component. 3 Component The electrodes shall be at Pre-heating : 150°C, 1min Adhesion least 90% covered with new Solder Composition : Sn/Pb=63/67 (Push Test) solder coating. Solder Temperature : 230±5°C Immersion Time : 4±1sec 4 Drop Test After test, the chip inductor Drop 1 time for each face and 1 time for each corner. don't fell of broke on the Total drop 10 times. P.C.Board Drop Height : 100cm Drop Weight : 125g 5 6 The terminal should at least after fluxing (alpha 100 or equiv), inductor shall be be 90% covered with solder dipped in a melted solder bath at 232±5°C for 5 seconds. Resistance to There shall be no case of MIL-STD202F, METHOD 215D solvent test deformation change in Solderability Test appearance of obliteration of marking NOTE : Specifications subject to change without notice. Please check our website for latest information. 15.01.2008 SUPERWORLD ELECTRONICS (S) PTE LTD PG. 5 WIREWOUND CHIP INDUCTORS SCI0805LP SERIES Climatic Test : SPECIFICATION ITEM 1 TEST CONDITIONS / TEST METHODS -40°C ~ +125°C Temperature Characteristics 2 Humidity Temperature : 40±2°C Resistance Relative Humidity : 90~95% Time : 96hrs ±2hrs Measured after exposure in the room condition for 2hrs 3 Low Temperature Appearance : No damage Temperature : -40±2°C Storage Test L change : within ±10% Time : 48±2hrs Q change : within ±20% Inductors are to be tested after 1 hour at room temperature. 4 One cycle : Thermal Shock Test Step Temperature (°C) Time (min) 1 -25±3 30 2 25±2 15 3 85±3 30 4 25±2 15 Total : 5 cycles 5 High Temperature Temperature : 125±2°C Storage Test Time : 48±2hrs Load : Allowed DC current 6 7 High Temperature There should be no Temperature : 85±2°C Load Life Test evidence of short of Time : 1000±12hrs open circuit. Load : Allowed DC current Humidity Load Temperature : 40±2°C Life Relative Humidity : 90~95% Time : 1000±12hrs Load : Allowed DC current NOTE : Specifications subject to change without notice. Please check our website for latest information. 15.01.2008 SUPERWORLD ELECTRONICS (S) PTE LTD PG. 6