UNISONIC TECHNOLOGIES CO., LTD 3513 CMOS IC PC POWER SUPPLY SUPERVISOR DESCRIPTION The UTC 3513 is designed to provide protection circuits, power good output (PGO) indicator, fault protection output (FPOB) and a PSONB control for PC switching power supply systems. The protection circuits include over voltage protection (OVP), under voltage protection (UVP) and over current protection(OCP) monitoring for 3.3V, 5V and two 12V. When 3.3V, 5V or 12V voltage is decreasing to 2.68V, 4.3V and 9.9V respectively, the under voltage protection (UVP) function will be enabled. FPO will be set to high to turn off the PWM controller IC. Toggling the PSONB from low to high will reset the fault protection latch. The voltage difference across external current shunt is used for OCP functions. An external resistor can be used to adjust protection threshold. The power supply is turned on after 38mS delay time when PSONB signal is set from high to low. To turn off power supply, PSONB signal is set from low to high with the delay time 38mS. The PGI circuitry provides a power-down warning signal for PGO. When PGI input is lower than the internal 1.20V reference voltage, PGO signal is pulled low. The device is available in two versions: UTC 3513E/3513F. Specially, fan control function is available in OTP/FC pin of UTC 3513F. * Pb-free plating product number: 3513EL/3513FL FEATURES * OVP/UVP monitors 3.3V, 5V, 12V input voltage level. * OCP monitors IS33, IS5, IS12 input current sense. * Fault protection output (FPOB) with Open Drain Output stage. * Power good output (PGO) with Open Drain Output stage. * 38ms de-bounce time for PSONB input signal. * 300ms time delay from PGI to PGO. * 2.4ms time delay for PSONB to turn off FPOB. www.unisonic.com.tw Copyright © 2007 Unisonic Technologies Co., Ltd 1 of 12 QW-R502-129.A 3513 CMOS IC ORDERING INFORMATION Order Number Normal Lead Free Plating 3513E-D16-T 3513EL-D16-T 3513E-S16-R 3513EL-S16-R 3513E-S16-T 3513EL-S16-T 3513F-D16-T 3513FL-D16-T 3513F-S16-R 3513FL-S16-R 3513F-S16-T 3513FL-S16-T Package Packing DIP-16 SOP-16 SOP-16 DIP-16 SOP-16 SOP-16 Tube Tape Reel Tube Tube Tape Reel Tube 3513EL-D16-T (1)Packing Type (2)Package Type (3)Lead Plating UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw (1) R: Tape Reel, T: Tube (2) D16: DIP-16, S16: SOP-16 (3) L: Lead Free Plating, Blank: Pb/Sn 2 of 12 QW-R502-129.A 3513 CMOS IC PIN ASSIGNMENT 3513E PGI 1 16 PGO GND 2 15 VDD FPOB 3 14 VS5 PSONB 4 13 IS5 OTP 5 12 VS33 RI 6 11 IS33 VS12B 7 10 VS12A IS12B 8 9 IS12A 3513F PGI 1 16 PGO GND 2 15 VDD FPOB 3 14 VS5 PSONB 4 13 IS5 OTP/FC 5 12 VS33 RI 6 11 IS33 VS12B 7 10 VS12A PWM 8 9 IS12AB UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw 3 of 12 QW-R502-129.A 3513 CMOS IC FUNCTION DESCRIPTION（1） ORDERING OTP low level OTP high level FC/PWM 3513E 3513F 2.45V 2.45V 3.25V 3.25V X ○ 73µs 73µs FPOB L H L H L H H H H PGO L L L L H L L L L tg2 FUNCTION DESCRIPTION（2） PGI PSONB UV&OC Protection OV Protection PGI<1.2V L No No PGI<1.2V L No Yes PGI<1.2V L Yes No PGI<1.2V L Yes Yes PGI>1.2V L No No PGI>1.2V L No Yes PGI>1.2V L Yes No PGI>1.2V L Yes Yes X H X X Note: FPOB=L means: fault is not latched. FPOB=H means: fault is latched PGO=L means: fault. PGO=H means: No fault X=do not care T(PSONB ON)/ T(PSONB OFF) 38ms 38ms PIN DESCRIPTIONS PIN NO PIN NAME TYPE 1 PGI Input 2 GND Supply 3 FPOB Output 4 PSONB Input 5 OTP/FC Input 6 RI Input 7 8 8 9 9 10 11 12 13 14 15 VS12B IS12B* PWM** IS12A* IS12AB** VS12A IS33 VS33 IS5 VS5 VDD Input Input Output Input Input Input Input Input Input Input Supply 16 PGO Output DESCRIPTION Power Good Input. For ATX SMPS, it detects AC line voltage through the main transformer. Ground Fault Protection Output. Output signal to control the primary PWM IC through an opto-coupler. When FPOB is low, the PWM IC is enabled. Remote On/Off logic input from CPU or main-board. The power supply will be turned on/off after 38mS delay. Over temperature protection/Fan speed control Reference setting. One external resistor Ri connected between RI and GND pin will determine a reference current, IREF = 1.20/Ri, for OCP programming. 12V over/under voltage protection. 12V over current protection. Pulse width modulation. 12V over current protection. 12V over current protection. 12V over/under voltage protection. 3.3V over current protection 3.3V over/under voltage protection 5V over current protection. 5V over/under voltage protection. Power supply. Power good logic output, 0 or 1(open-drain). Power good=1 means that the power supply is good for operation. The power good delay is 300mS. * 3513E only ** 3513F only UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw 4 of 12 QW-R502-129.A 3513 CMOS IC BLOCK DIAGRAM VDD RST PGI Bandgap Reference VREF=1.2V + UN - 73 µs debounce clr PGO 300ms delay V12A IS33 + I REF*8 VS33 73 µs debounce + OV + UN V12A IS12A + IREF*8 VS12A PWR Power On Reset 2.4ms Internal Power VCCI=3.6V 38 ms debounce delay + OV - FPOB RQ S Q PSONB OTP 75ms/ 300ms delay + UN - 2.4V~3.2V V12A IS12B PWR + IREF*8 VS12B OSC + OV - CLK + UN V12A IS5 V12A + - VREF=1.2V IREF*8 VS5 + RI + OV + UN - Figure 1. 3513E UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw 5 of 12 QW-R502-129.A 3513 CMOS IC BLOCK DIAGRAM(Cont.) VDD RST PGI Bandgap Reference VREF=1.2V + UN - 73µs/ debounce clr PGO 300ms delay V12A IS33 + 73µs debounce IREF*8 VS33 + OV - FPOB R Q S Q + UN V12A IS12AB Power On Reset + PWR Internal Power VCCI=3.6V 2.4ms IREF*8 VS12A delay + OV + - 38ms debounce PSONB OTP/FC 75ms/300ms delay UN 2.4V~3.2V V12A + IREF*8 VS12B + + - PWR UN V12A IS5 PWM - + OV - OSC + CLK IREF*8 VS5 V12A + OV - + - VREF=1.2V + - UN RI Figure 2. 3513F UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw 6 of 12 QW-R502-129.A 3513 CMOS IC ABSOLUTE MAXIMUM RATINGS PARAMETER SYMBOL RATINGS UNIT -0.3 ~ 16 V VS5,VS33 -0.3 ~ 7 V VS12A, VS12B -0.3 ~ 16 V Input Voltage VIN IS12A, IS12B, IS5, IS33 -0.3 ~ V12A+0.3 V -0.3 ~ 7 V PSONB, PGI, OTP FPOB V -0.3 ~ VDD+0.3 Output Voltage VOUT PGO -0.3 ~ VDD+0.3 V ℃ Operating Temperature TOPR -40 ~ +125 ℃ Storage Temperature TSTG -55 ~ +150 Note 1. Absolute maximum ratings are those values beyond which the device could be permanently damaged. Absolute maximum ratings are stress ratings only and functional device operation is not implied. 2. Stress above those listed may cause permanent damage to the devices. Supply Voltage VDD RECOMMENDED OPERATING CONDITIONS PARAMETER SYMBOL VDD Supply Voltage VS5,VS33 VS12A, VS12B IS12A, IS12B, IS5, IS33 PSONB, PGI,OTP FPOB PGO FPOB PGO Input Voltage Output Voltage Output Sink Current RI Output Current Supply Voltage Rising Time (VDD) MIN 4 TYP 12 VIN VOUT IO(SINK) IO(RI) tR 10 1 MAX 15 7 15 15 7 7 7 30 10 65 UNIT V V V V V V V mA mA uA ms ELECTRICAL CHARACTERISTICS (Ta=25℃ and VDD=5V and V12A=12V) PARAMETER Over Voltage Detection Over Voltage Threshold SYMBOL V12A, V12B V5 V33 Low Level Output Voltage (FPOB) VOL Output Leakage Current (FPOB) PSONB High-Level Input Voltage Low-Level Input Voltage Input Pull-up Current PGI and PGO ILEAK Under Voltage Threshold Input Threshold Voltage (PGI) Low Level Output Voltage (PGO) Output Leakage current (PGO) OTP/FC High-Level Input Voltage (OTP) Low-Level Input Voltage (OTP) Start-up Voltage (FC) TEST CONDITIONS VIH VIL IIN MAX UNIT 13.2 5.7 3.7 13.8 5.95 3.9 14.4 6.2 4.1 0.3 0.7 5 V V V 2 @ PSONB=0V 3513E/3513F UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw TYP @ ISINK=10mA @ ISINK=30mA @ V(FPOB)=5V V12A, V12B V5 V33 VI(THD) VOL @ ISINK=10mA ILEAK @ PGO=5V VIH VIL MIN V uA 0.8 V V uA 100 9.5 4.15 2.54 1.16 9.90 4.30 2.68 1.20 10.5 4.45 2.82 1.24 0.4 5 V V V V V uA 3.10 2.30 0.7 3.25 2.45 0.8 3.40 2.60 0.9 V V V 7 of 12 QW-R502-129.A 3513 CMOS IC ELECTRICAL CHARACTERISTICS (Cont.) PARAMETER SYMBOL TEST CONDITIONS Stop Voltage (FC) PWM High Level Output Voltage VOH @ ISOURCE=4.5mA Low Level Output Voltage VOL @ ISINK=4.5mA Output Leakage Current ILEAK PWM Frequency fPWM SWITCHING CHARACTERISTICS PSONB ON（PSONB Low to FPOB T(PSONB ON) @ VDD=5V Low） PSONB OFF（PSONB Hi to PGO T(PSONB OFF) @ VDD=5V Low） @ VDD=5V PGI to PGO Delay Time TPG Timing PGO Low to FPO high TPSOFF @ VDD=5V TUVP1 @ FPOB=Low & PGI > 1.2V UVD/OCD turn on delay Time @ FPOB=Low & PGI < 1.2V TUVP2 Noise Deglitch Time tg1 Noise Deglitch Time for Latch tg2 TOTAL DEVICE Low Voltage VDD Supply Current IDD @ PSONB=5V UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw MIN 0.55 TYP 0.65 MAX 0.75 UNIT V 28 35 0.4 5 42 V V µA KHz 32 38 62 ms 32 38 62 ms 200 2.0 65 260 63 63 300 2.4 75 300 75 75 490 4 122 488 120 120 ms ms ms ms µs µs 1 V mA V12A-0.4 3.6 8 of 12 QW-R502-129.A 3513 CMOS IC APPLICATION CIRCUIT 5VSB 5V 3513E 3KΩ 100Ω PGI 1 2 10KΩ 300 4 PGO GND VDD FPOB VS5 PSONB IS5 3 PSONB 0.01μF 15 14 47Ω 13 IS5 +3.3V 0.01μF OTP RI 12VB IS12B 5 6 OTP RI VS33 IS33 7 VS12B VS12A IS12B IS12A 8 UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw 16 PGI 12 11 10 9 IS33 12VA IS12A 9 of 12 QW-R502-129.A 3513 CMOS IC APPLICATION CIRCUIT(Cont.) UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw 10 of 12 QW-R502-129.A 3513 CMOS IC TYPICAL TIMMING DIAGRAM 1) PGI (UNDER-VOLTAGE): 2) V33, V5, V12A, V12B (UNDER-VOLTAGE) or IS33, IS5, IS12A, IS12B (OVER-CURRENT): UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw 11 of 12 QW-R502-129.A 3513 CMOS IC TYPICAL TIMMING DIAGRAM 3) V33, V5, V12A, V12B (OVER-VOLTAGE). 4) OTP/FC, PWM, FPOB: (at VDD=5V, PSONB=0V, V12A, V12B =12V, V5=5V, V33=3.3V) UTC assumes no responsibility for equipment failures that result from using products at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges, or other parameters) listed in products specifications of any and all UTC products described or contained herein. UTC products are not designed for use in life support appliances, devices or systems where malfunction of these products can be reasonably expected to result in personal injury. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner. The information presented in this document does not form part of any quotation or contract, is believed to be accurate and reliable and may be changed without notice. UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw 12 of 12 QW-R502-129.A