UNISONIC TECHNOLOGIES CO., LTD 8561 Preliminary CMOS IC POWER FACTOR CORRECTOR DESCRIPTION The UTC 8561 is a Power Factor Corrector, which can work in wide input voltage range applications (from 85V ~ 265V) with an excellent THD. It has very low start up current (about 50 uA) and a disable function on the ZCD pin, which is designed to keep lower current consumption in stand by mode. The device is operating in transition mode, and is able to drive a Power MOS or IGBT with a ± 400mA current for sourcing and sinking. FEATURES * 1% Precision (@ TJ = 25°C) Internal Reference Voltage * Output Overvoltage Protection * Very Low Power Start-Up Current * Very Low Operating Supply Current * Current Sense Filter On Chip * Disable Function (with ZCD Pin) * Transition Mode Operation * Gate Driving Current: ± 400mA ORDERING INFORMATION Ordering Number Lead Free Plating Halogen Free 8561L-D08-T 8561G-D08-T www.unisonic.com.tw Copyright © 2010 Unisonic Technologies Co., Ltd Package Packing DIP-8 Tube 1 of 6 QW-R502-444.a 8561 Preliminary PIN CONFIGURATION 1 8 Vcc COMP 2 7 GD MULT 3 6 GND 4 5 ZCD INV CS CMOS IC PIN DESCRIPTION PIN NO 1 2 3 4 5 6 7 8 PIN NAME INV COMP MULT CS ZCD GND GD VCC DESCRIPTION Inverting input of the error amplifier. Output of the error amplifier. Input of the multiplier stage. Input of the current sense stage. Input of the zero current detection. Ground. Gate driver output. Voltage supply. UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw 2 of 6 QW-R502-444.a 8561 Preliminary CMOS IC BLOCK DIAGRAM COMP 2 MULT 3 20V 8 VCC R1 OVER-VOLTAGE DETECTION INV 1 2.5V - UVLO VREF2 R2 MULTIPLIER + INTERNAL SUPPLY 7V CS 4 + 40K R - 5pF ZCD 5 2.1V 1.6V ZERO CURRENT DETECTOR + - S Q D R I V E R VOLTAGE REGULATOR VCC 7 GD STARTER DISABLE 6 GND UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw 3 of 6 QW-R502-444.a 8561 Preliminary CMOS IC ABSOLUTE MAXIMUM RATINGS (Ta=25°C, unless otherwise specified) PARAMETER Analog Inputs & Outputs Current Sense Input Iq+Iz (IGD = 0) Output Totem Pole Peak Current (2ms) RATINGS UNIT -0.3 ~ 7 V -0.3 ~ 7 V 30 mA ±700 mA 50 (source) mA Zero Current Detector ZCD -10 (sink) mA Power Dissipation PD 0.65 W Junction Temperature TJ 150 °C Storage Temperature TSTG -55 ~ +150 °C Note: Absolute maximum ratings are those values beyond which the device could be permanently damaged. Absolute maximum ratings are stress ratings only and functional device operation is not implied. SYMBOL INV, COMP MULT CS IVCC IGD ELECTRICAL CHARACTERISTICS (VCC=14.5V, Ta=-25°C ~ 125°C, unless otherwise specified) PARAMETER SUPPLY VOLTAGE SECTION Operating Range Turn-ON Threshold Turn-OFF Threshold Hysteresis SUPPLY CURRENT SECTION Start-up Current Quiescent Current PIN SYMBOL 8 8 8 8 VCC VCC(ON) VCC(OFF) Hys 8 8 ISTART-U Iq 8 ICC Operating Supply Current Quiescent Current Zener Voltage ERROR AMPLIFIER SECTION Voltage Feedback Input Threshold Line Regulation Input Bias Current Voltage Gain Gain Bandwidth Source Current Sink Current Upper Clamp Voltage Lower Clamp Voltage MULTIPLIER SECTION Linear Operating Voltage 8 8 8 VZ 1 VINV 1 IINV GV GB Iq 2 ICOMP 2 VCOMP 3 VMULT △VCS △Vmult K Output Max.Slope Gain CURRENT SENSE COMPARATOR Current Sense Reference 4 Clamp Input Bias Current 4 Delay to Output 4 Current Sense Offset 4 VCS ICS td(H-L) TEST CONDITIONS after turn-on 11 11 8.7 2.2 before turn-on (VCC=11V) 20 CL=1nF @ 70KHz In OVP condition Vpin1=2.7V VPIN5≤150mA, VCC>VCC off VPIN5≤150mV, VCC<VCC off ICC=25mA 20 18 Ta=25°C 12V<VCC<18V VCC=12 ~ 18V 2.465 2.44 Open loop 60 VCOMP=4V, VINV=2.4V VCOMP=4V, VINV=2.6V ISOURCE=0.5mA Isink=0.5mA -2 2.5 VMULT=from 0V ~ 0.5V VCOMP=Upper ClamVoltage VMULT=1V, VCOMP=4V VMULT=2.5V VCOMP=Upper Clamp Voltage VOS=0 UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw MIN TYP MAX UNIT 12 9.5 2.5 18 13 10.3 2.8 V V V V 50 2.6 4 1.4 1.4 50 20 90 4 5.5 μA mA mA mA mA μA V 2.5 2.535 2.56 5 -1000 2 -100 80 1 -4 4.5 5.8 2.25 90 30 -8 V V mV uA dB MHz mA mA V V 0~ 3 0 ~ 3.5 V 1.65 1.9 0.45 0.6 0.75 1/V 1.6 1.7 1.8 V -0.05 200 0 -1 450 15 μA ns mV 4 of 6 QW-R502-444.a 8561 Preliminary CMOS IC ELECTRICAL CHARACTERISTICS (Cont.) PARAMETER ZERO CURRENT DETECTOR Input Threshold Voltage Rising Edge (Note) Hysteresis (Note) Upper Clamp Voltage Upper Clamp Voltage Lower Clamp Voltage Sink Bias Current Source Current Capability Sink Current Capability Disable threshold Restart Current After Disable OUTPUT SECTION PIN Dropout Voltage 5 5 5 5 5 5 5 5 5 7 SYMBOL TEST CONDITIONS VZCD VZCD VZCD IZCD IZCD IZCD VDIS IZCD VGD TYP MAX 2.1 VZCD IZCD=20μA IZCD=3mA IZCD=3mA 1V≦VZCD≦4.5V 0.3 4.5 4.7 0.3 0.5 5.0 5.1 0.65 2 -3 3 200 -200 VZCD<Vdis, VCC>VCOFF IGDsource=200mA IGDsource=20mA IGDsink=200mA IGDsink=20mA CL=1nF CL=1nF VCC=3.5V, VGD=1V Output Voltage Rise Time 7 tR Output Voltage Fall Time 7 tF IGD Sink Current 7 IGD(OFF) OUTPUT OVERVOLTAGE SECTION OVP Triggering Current 2 IOVP Static OVP Threshold RESTART TIMER Start Timer tSTART Note: Parameter guaranteed by design, not tested in production. UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw MIN 1.2 0.7 UNIT V 0.7 6.8 7 1 -10 10 300 -300 V V V V μA mA mA mV μA 2 1 1.5 0.3 100 100 V V V V ns ns mA 5 40 40 10 35 2.1 40 2.25 45 2.4 μA V 70 150 400 μs 5 of 6 QW-R502-444.a 8561 Preliminary CMOS IC TYPICAL APPLICATION CIRCUIT (80W, Wide-range Mains) D1 BYT13-600 + R3(*) 240K D3 1N4150 R2 C6 D2 1N5248B 100 12nF R1 68K + UTC 8561 3 R10 C2 10K 22μF 25V NTC 2 5 8 C1 1μF 400V Vac (85V ~ 265V) (*) R3 = 2×120KΩ R6 = 0.82Ω /2 R7 = 2×499KΩ, 1% R9 = 2×620KΩ 1μF R9(*) 1.24M - R7(*) 998K C3 BRIDGE 4×1N4077 FUSE 4A/250V VOUT=400V PO=80W T 6 C7 10nF 1 R5 7 MOS STP8NA50 10 C5 47μF 450V 4 R6(*) 0.41 1W R8 6.34K 1% - TRANSFORMER T: core THOMSON-CSF B1ET2910A(ETD29×16×10mm)OR EQUIVALENT (OREGA 473201A8) primary 90T of Litz wire 10×0.2mm secondary 7T of #27 AWG (0.15mm) gap 1.25mm for a total primary inductance of 0.8mH UTC assumes no responsibility for equipment failures that result from using products at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges, or other parameters) listed in products specifications of any and all UTC products described or contained herein. UTC products are not designed for use in life support appliances, devices or systems where malfunction of these products can be reasonably expected to result in personal injury. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner. The information presented in this document does not form part of any quotation or contract, is believed to be accurate and reliable and may be changed without notice. UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw 6 of 6 QW-R502-444.a