UTC-IC U74HCT4066

UNISONIC TECHNOLOGIES CO., LTD
U74HCT4066
CMOS IC
QUAD BILATERAL SWITCH
„
DESCRIPTION
The UTC U74HCT4066 consists of four independent analog
switches. Each switch has an Enable input (nE) which is active HIGH
to decide the switch status.
„
FEATURES
*Operation voltage range: 4.5V~5.5V
*Very low “ON” resistance: 50Ω(Typ.)@VCC=4.5V
„
ORDERING INFORMATION
Ordering Number
Lead Free
Halogen Free
U74HCT4066L-P14-R
U74HCT4066G-P14-R
U74HCT4066L-S14-R
U74HCT4066G-S14-R
www.unisonic.com.tw
Copyright © 2009 Unisonic Technologies Co., Ltd
Package
Packing
TSSOP-14
SOP-14
Tape Reel
Tape Reel
1 of 6
QW-R502-286.B
U74HCT4066
„
„
CMOS IC
PIN CONFIGURATION
1Y
1
14
VCC
1Z
2
13
1E
2Z
3
12
4E
2Y
4
11
4Y
2E
5
10
4Z
3E
6
9
3Z
GND
7
8
3Y
FUNCTION TABLE
INPUTS(nE)
SWITCH
H
ON
L
OFF
Note: H: High voltage level; L: Low voltage level.
„
LOGIC DIAGRAM
UNISONIC TECHNOLOGIES CO., LTD
www.unisonic.com.tw
2 of 6
QW-R502-286.B
U74HCT4066
„
CMOS IC
ABSOLUTE MAXIMUM RATING (unless otherwise specified)
PARAMETER
SYMBOL
RATINGS
UNIT
Supply Voltage
VCC
-0.5 ~ +11
V
Input Diode Current
IIK
±20
mA
Switch Diode Current
ISK
±20
mA
Switch Current
IS
±25
mA
VCC or GND Current
ICC
±50
mA
Power Dissipation
500
mW
PD
Derate above 60°C
TSSOP-14
5.5
mW/°C
8
mW/°C
Derate above70°C
SOP-14
Storage Temperature
TSTG
-65 ~ +150
°C
Note: Absolute maximum ratings are those values beyond which the device could be permanently damaged.
Absolute maximum ratings are stress ratings only and functional device operation is not implied.
„
RECOMMENDED OPERATING CONDITIONS
PARAMETER
Supply Voltage
Input Voltage
Switch Voltage
Input Transition Rise or Fall Rate
Operating Temperature
„
SYMBOL
TEST CONDITIONS
VCC
VIN
VS
tR, tF
VCC =2V
TA
MIN
4.5
GND
GND
6
-40
MAX
5.5
VCC
VCC
500
85
UNIT
V
V
V
ns
°C
MAX
UNIT
V
V
μA
ELECTRICAL CHARACTERISTICS
PARAMETER
High-Level Input Voltage
Low-Level Input Voltage
Input Leakage Current
SYMBOL
TEST CONDITIONS
MIN
VIH
VCC=4.5V to 5.5V
2
VIL
VCC=4.5V to 5.5V
II(LEAK)
VCC=5.5V,VIN=VCC or GND
VCC=5.5V, VIN=VIH or VIL,
OFF-state
current per channel
IS
VS=VCC-GND
ON-state
VCC=4.5V to 5.5V ,
Quiescent Supply Current
IQ
VIN=VIS=VOS=VCC or GND
VCC=4.5V to 5.5V, VIN=VCC-2.1V,
Additional Quiescent Supply Current
∆ IQ
Other inputs at VCC or GND
VIN=VIH or VIL, VIS=VCC to GND,
Peak
RON
VCC=4.5V, IS=1mA
ON-resistance
VIN=VIH or VIL,
VIS=GND
Rail
RON
VCC=4.5V, IS=1mA
VIS=VCC
VIN= VIH or VIL ,VIS= VCC to
Maximum variation of ON-resistance
△RON
between any two channels
GND, VCC =4.5V
„
TYP
5.0
TYP
0.8
±1.0
±1.0
±1.0
μA
20
μA
100
450
μA
54
118
Ω
35
42
95
106
Ω
Ω
5
Ω
DYNAMIC CHARACTERISTICS (Ta=25℃, GND=0V; tR=tF=6ns; CL=50pF)
PARAMETER
Propagation Delay From VIS to VOS
Turn-ON Time from nE to VOS
Turn-OFF Time from nE to VOS
Sine-Wave Distortion
SYMBOL
TEST CONDITIONS
tPHL/tPLH VCC=4.5V, RL=∞
tPZH/tPZL VCC=4.5V, RL=1KΩ
tPHZ/tPLZ VCC=4.5V, RL=1KΩ
VCC=4.5V, VIS(P-P)=4V, f=1kHz,
THD
RL=10k
MIN
TYP
3
12
20
MAX
15
30
44
UNIT
ns
ns
ns
0.04
%
Switch OFF Signal Feed-Through
(Note 1)
αOFF
VCC=4.5V, RL=600Ω, f=1MHz
-50
dB
Crosstalk Between any two Switches
(Note 1)
αCT(S)
VCC=4.5V, RL=600Ω, f=1MHz
-60
dB
Crosstalk Voltage between any input to
any Switch (Peak-to-Peak Value)
V(P-P)
VCC=4.5V, RL=600Ω, f=1MHz
110
mV
UNISONIC TECHNOLOGIES CO., LTD
www.unisonic.com.tw
3 of 6
QW-R502-286.B
U74HCT4066
„
CMOS IC
DYNAMIC CHARACTERISTICS(Cont.)
PARAMETER
SYMBOL
TEST CONDITIONS
Minimum Frequency Response(-3dB)
fMAX
VCC=4.5V, RL=50Ω, CL=10pF
(Note 2)
maximum switch capacitance
CS
Note 1. Adjust input voltage VIS is 0dbm level (0dbm=1mW into 600Ω)
2. Adjust input voltage VIS is 0dbm level at VOS for 1MHz (0dbm=1mW into 50Ω)
UNISONIC TECHNOLOGIES CO., LTD
www.unisonic.com.tw
MIN
TYP
MAX
UNIT
180
MHz
8
pF
4 of 6
QW-R502-286.B
U74HCT4066
„
CMOS IC
TEST CIRCUIT AND WAVEFORMS
Test circuit for measuring ON-resistance (Ron)
Test circuit for measuring OFF-state current
Test circuit for measuring ON-state current
UNISONIC TECHNOLOGIES CO., LTD
www.unisonic.com.tw
5 of 6
QW-R502-286.B
U74HCT4066
„
CMOS IC
TEST CIRCUIT AND WAVEFORMS(Cont.)
tPLH/tPHL
tPHZ/tPZH
tPLZ/tPZL
S
OPEN
GND
VCC
VIN
VCC
GND
Note: 1. CL includes probe and jig capacitance.
Note: 2.PRR ≤1MHz, Zo = 50Ω, tR ≤6ns, tF ≤6ns.
UTC assumes no responsibility for equipment failures that result from using products at values that
exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges, or
other parameters) listed in products specifications of any and all UTC products described or contained
herein. UTC products are not designed for use in life support appliances, devices or systems where
malfunction of these products can be reasonably expected to result in personal injury. Reproduction in
whole or in part is prohibited without the prior written consent of the copyright owner. The information
presented in this document does not form part of any quotation or contract, is believed to be accurate
and reliable and may be changed without notice.
UNISONIC TECHNOLOGIES CO., LTD
www.unisonic.com.tw
6 of 6
QW-R502-286.B