UNISONIC TECHNOLOGIES CO., LTD U74HCT4066 CMOS IC QUAD BILATERAL SWITCH DESCRIPTION The UTC U74HCT4066 consists of four independent analog switches. Each switch has an Enable input (nE) which is active HIGH to decide the switch status. FEATURES *Operation voltage range: 4.5V~5.5V *Very low “ON” resistance: 50Ω(Typ.)@VCC=4.5V ORDERING INFORMATION Ordering Number U74HCT4066G-P14-R U74HCT4066G-S14-R Package TSSOP-14 SOP-14 Packing Tape Reel Tape Reel MARKING www.unisonic.com.tw Copyright © 2014 Unisonic Technologies Co., Ltd 1 of 6 QW-R502-286.C U74HCT4066 CMOS IC PIN CONFIGURATION 1Y 1 14 VCC 1Z 2 13 1E 2Z 3 12 4E 2Y 4 11 4Y 2E 5 10 4Z 3E 6 9 3Z GND 7 8 3Y FUNCTION TABLE INPUTS(nE) SWITCH H ON L OFF Note: H: High voltage level; L: Low voltage level. LOGIC DIAGRAM UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw 2 of 6 QW-R502-286.C U74HCT4066 CMOS IC ABSOLUTE MAXIMUM RATING (TA=25°C,unless otherwise specified) PARAMETER SYMBOL RATINGS UNIT Supply Voltage VCC -0.5 ~ +11 V Input Diode Current IIK ±20 mA Switch Diode Current ISK ±20 mA Switch Current IS ±25 mA VCC or GND Current ICC ±50 mA Power Dissipation 500 mW Derate above 60°C TSSOP-14 PD 5.5 mW/°C Derate above70°C SOP-14 8 mW/°C Storage Temperature TSTG -65 ~ +150 °C Note: Absolute maximum ratings are those values beyond which the device could be permanently damaged. Absolute maximum ratings are stress ratings only and functional device operation is not implied. RECOMMENDED OPERATING CONDITIONS (TA=25°C,unless otherwise specified) PARAMETER Supply Voltage Input Voltage Switch Voltage Input Transition Rise or Fall Rate Operating Temperature SYMBOL TEST CONDITIONS VCC VIN VS tR, tF VCC =2V TA MIN 4.5 GND GND 6 -40 MAX 5.5 VCC VCC 500 85 UNIT V V V ns °C MAX UNIT V V μA ELECTRICAL CHARACTERISTICS (TA=25°C,unless otherwise specified) PARAMETER High-Level Input Voltage Low-Level Input Voltage Input Leakage Current SYMBOL TEST CONDITIONS MIN VIH VCC=4.5V to 5.5V 2 VIL VCC=4.5V to 5.5V II(LEAK) VCC=5.5V,VIN=VCC or GND OFF-state VCC=5.5V, VIN=VIH or VIL, current per channel IS VS=VCC-GND ON-state VCC=4.5V to 5.5V , Quiescent Supply Current IQ VIN=VIS=VOS=VCC or GND VCC=4.5V to 5.5V, VIN=VCC-2.1V, Additional Quiescent Supply Current ∆ IQ Other inputs at VCC or GND VIN=VIH or VIL, VIS=VCC to GND, Peak RON VCC=4.5V, IS=1mA ON-resistance VIS=GND VIN=VIH or VIL, Rail RON VCC=4.5V, IS=1mA VIS=VCC Maximum variation of ON-resistance VIN= VIH or VIL ,VIS= VCC to △RON between any two channels GND, VCC =4.5V TYP 5.0 TYP 0.8 ±1.0 ±1.0 ±1.0 μA 20 μA 100 450 μA 54 118 Ω 35 42 95 106 Ω Ω 5 Ω DYNAMIC CHARACTERISTICS (TA=25℃, GND=0V; tR=tF=6ns; CL=50pF) PARAMETER Propagation Delay From VIS to VOS Turn-ON Time from nE to VOS Turn-OFF Time from nE to VOS Sine-Wave Distortion Switch OFF Signal Feed-Through (Note 1) Crosstalk Between any two Switches (Note 1) Crosstalk Voltage between any input to any Switch (Peak-to-Peak Value) SYMBOL TEST CONDITIONS tPHL/tPLH VCC=4.5V, RL=∞ tPZH/tPZL VCC=4.5V, RL=1KΩ tPHZ/tPLZ VCC=4.5V, RL=1KΩ VCC=4.5V, VIS(P-P)=4V, f=1kHz, THD RL=10k TYP 3 12 20 MAX 15 30 44 UNIT ns ns ns 0.04 % αOFF VCC=4.5V, RL=600Ω, f=1MHz -50 dB αCT(S) VCC=4.5V, RL=600Ω, f=1MHz -60 dB V(P-P) VCC=4.5V, RL=600Ω, f=1MHz 110 mV UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw MIN 3 of 6 QW-R502-286.C U74HCT4066 CMOS IC DYNAMIC CHARACTERISTICS(Cont.) PARAMETER SYMBOL TEST CONDITIONS MIN Minimum Frequency Response(-3dB) fMAX VCC=4.5V, RL=50Ω, CL=10pF (Note 2) maximum switch capacitance CS Notes: 1. Adjust input voltage VIS is 0dbm level (0dbm=1mW into 600Ω) 2. Adjust input voltage VIS is 0dbm level at VOS for 1MHz (0dbm=1mW into 50Ω) UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw TYP MAX UNIT 180 MHz 8 pF 4 of 6 QW-R502-286.C U74HCT4066 CMOS IC TEST CIRCUIT AND WAVEFORMS Test circuit for measuring ON-resistance (Ron) Test circuit for measuring OFF-state current Test circuit for measuring ON-state current UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw 5 of 6 QW-R502-286.C U74HCT4066 CMOS IC TEST CIRCUIT AND WAVEFORMS(Cont.) tPLH/tPHL tPHZ/tPZH tPLZ/tPZL S OPEN GND VCC VIN VCC GND Note: 1. CL includes probe and jig capacitance. Note: 2.PRR ≤1MHz, Zo = 50Ω, tR ≤6ns, tF ≤6ns. UTC assumes no responsibility for equipment failures that result from using products at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges, or other parameters) listed in products specifications of any and all UTC products described or contained herein. UTC products are not designed for use in life support appliances, devices or systems where malfunction of these products can be reasonably expected to result in personal injury. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner. The information presented in this document does not form part of any quotation or contract, is believed to be accurate and reliable and may be changed without notice. UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw 6 of 6 QW-R502-286.C