UNISONIC TECHNOLOGIES CO., LTD UM604/A LINEAR INTEGRATED CIRCUIT QUAD OPERATIONAL AMPLIFIER AND PROGRAMMABLE VOLTAGE REFERENCE SOP-16 DESCRIPTION The UTC UM604/A is a monolithic IC that includes four op-amps and an adjustable shunt voltage reference. This device is offering space and cost saving in many applications like power supply management or data acquisition systems. DIP-16 FEATURES *Pb-free plating product number: UM604L/UM604AL OPERATIONAL AMPLIFIER * Low supply current : 375µA/op.(@ VCC= 5 V) * Low input bias current : 20nA * Medium speed : 0.9MHz * Low input offset voltage : 0.5mV typ for UM604 * Wide power supply range: ±1.5 ~ ±15V VOLTAGE REFERENCE * Adjustable output voltage : VREF to 36V * 0.4% and 1% voltage precision * Sink current capability : 1 ~ 100mA * Typical output impedance : 0.2Ω ORDERING INFORMATION Ordering Number Normal Lead Free Plating UM604-D16-T UM604L-D16-T UM604-S16-R UM604L-S16-R UM604-S16-T UM604L-S16-T UM604A-D16-T UM604AL-D16-T UM604A-S16-R UM604AL-S16-R UM604A-S16-T UM604AL-S16-T www.unisonic.com.tw Copyright © 2007 Unisonic Technologies Co., Ltd Package Packing DIP-16 SOP-16 SOP-16 DIP-16 SOP-16 SOP-16 Tube Tape Reel Tube Tube Tape Reel Tube 1of 7 QW-R105-032.B UM604/A LINEAR INTEGRATED CIRCUIT PIN CONFIGURATION UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw 2 of 7 QW-R105-032.B UM604/A LINEAR INTEGRATED CIRCUIT ABSOLUTE MAXIMUM RATINGS PARAMETER SYMBOL RATINGS UNIT Supply Voltage VCC 36 V Differential Input Voltage VDIFF 36 V Input Voltage VIN -0.3 ~ +36 V Output Short-Circuit Duration ID Infinite Junction Temperature TJ +150 °C Operating Temperature TOPR -55 ~ +125 °C Note: Absolute maximum ratings are those values beyond which the device could be permanently damaged. Absolute maximum ratings are stress ratings only and functional device operation is not implied. ELECTRICAL CHARACTERISTICS VCC+=5V, VCC-=0V, Ta=25℃ (unless otherwise specified) PARAMETER SYMBOL TEST CONDITIONS Total Supply Current, Excluding VCC+=5V, no load, TMIN<Ta<TMAX ICC Current In The Voltage Reference VCC+=30V, no load, TMIN<Ta<TMAX MIN 1.4 TYP MAX 2.4 4 UNIT MAX 3 4 5 6 UNIT mA ELECTRICAL CHARACTERISTICS + - VCC =5V, VCC =Ground, VOUT=1.4V, Ta=25℃ (unless otherwise specified) PARAMETER SYMBOL TEST CONDITIONS Ta=25°C UM604A TMIN≤Ta≤ TMAX Input Offset Voltage VI(OFF) Ta=25°C UM604 TMIN≤Ta≤ TMAX Input Offset Voltage Drift TMIN≤Ta≤ TMAX Input Bias Current II(BIAS) TMIN≤Ta≤ TMAX Supply Voltage Rejection Ratio Input Common Mode Voltage Range SVR 2 20 VCC=15V, RL=2k, VOUT=1.4V ~11.4V TMIN≤Ta≤ TMAX 50 25 100 VCC=5V ~ 30V 65 100 1 VI(CM) VCC=+30V(see note ) TMIN≤Ta≤ TMAX Common Mode Rejection Ratio CMRR TMIN≤Ta≤ TMAX Output Current Source IO(SOUR) VOUT=2V, VCC=+15V, VID=+1V Output Short Circuit to Ground Output Current Sink IO(SC) IO(SINK) 0 0 70 60 20 VCC=+15V VID= -1V, VCC=+15V, VOUT=+2V 30 50 150 200 nA nA V/mV dB (Vcc+)-1.5 (Vcc+)-2 85 V dB 40 40 mV µV/° C 7 II(OFF) GV TYP 0.5 1 △VI(OFF) Input Offset Current. Large Signal Voltage Gain MIN mA 60 mA 10 20 mA 27 27 28 V VCC+=30V High Level Output Voltage VOH Low Level Output Voltage VOL Slew Rate at Unity Gain SR Gain Bandwidth Product GBP RL=10k , Ta=25℃ TMIN≤Ta≤ TMAX RL=10k TMIN≤Ta≤ TMAX 20 20 mV VIN=0.5 ~ 3V, VCC=15V RL=2kΩ, CL=100pF, unity gain 0.1 0.3 V/µs Vcc=30V, RL=2K, CL=100pF f=100kHz, Vin=10mV 0.5 0.9 MHz UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw 5 3 of 7 QW-R105-032.B UM604/A LINEAR INTEGRATED CIRCUIT ELECTRICAL CHARACTERISTICS(Cont.) PARAMETER SYMBOL Total Harmonic Distortion THD TEST CONDITIONS f=1kHz GV=20dB, RL=2, VCC=30V CL=100pF, Vo=2Vpp MIN TYP MAX 0.02 UNIT % nV Equivalent Input Noise Voltage eN F=1kHz, Vcc=30V, Rs=100Ω 50 Channel Separation CS 1kHz<f<20kHz 120 Hz dB Note 1: The input common-mode voltage of either input signal voltage should not be allowed to go negative by more than 0.3V, the upper end of the common-mode voltage range is Vcc+-1.5V. But either of both inputs can go to +36V without damage. VOLTAGE REFERENCE PARAMETER SYMBOL Ik Cathode Current PARAMETER Reference Input Voltage SYMBOL UM604A VREF UM604 Reference Input Voltage Deviation Over Temperature Range Ratio of Change in Reference Input Voltage to Charge in Cathode to Anode Voltage △VREF △VKA IREF Reference Input Current Deviation over TºRange Minimum Cathode Current for Regulation Off-State Cathode current Dynamic Impedance-note TEST CONDITIONS ±0.4%, Ta=25℃ TMIN≤Ta≤ TMAX ±1%, Ta=25℃ TMIN≤Ta≤ TMAX MIN 2.49 2.48 2.475 2.45 VKA=VREF; Ik=10mA TMIN≤Ta≤ TMAX UNIT mA TYP 2.5 2.5 MAX 2.51 2.52 2.525 2.55 UNIT V mV 7 30 △VREF Reference Input Current 1) RATING 1 ~ 100 IMIN Ik=10mA, △VKA=36V ~ 3V Ik=10mA TMIN≤Ta≤ TMAX VKA= VREF IOFF 「ZKA」 VKA= VREF, △Ik=1 ~ 100mA, f<1kHz 1.The dynamic impedance is defined as「ZKA」= -1.1 MV/V 1.5 2.5 3 µA 0.8 1.2 µA 0.5 1 mA 180 500 nA 0.2 0.5 Ω △VkA △VIk UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw -2 4 of 7 QW-R105-032.B UM604/A OPERATIONAL AMPLIFIERS Unit Frequency=F(I) Vcc=±15V,RL=2K,CL=100PF Unit Freq Thousands 1000 800 600 400 200 0 -0.015 -0.01 0 -0.005 SOURCE<= I(A) 0.01 0.005 0.015 =>Sink GBP=F(I) Vcc=±15V,RL=2K,CL=100PF GBP Thousands 800 600 400 200 0 -0.015 -0.01 -0.005 0 SOURCE<= I(A) 0.01 0.005 =>Sink 0.015 phase and Gain Margin=F(I) Vcc=±15V,RL=2K,CL=100PF 0 60 -4 40 -6 30 -8 20 -10 10 0 -0.015 Gain Margin(dB) -2 50 Phase Margin(deg) LINEAR INTEGRATED CIRCUIT -12 -14 -0.01 -0.005 0 SOURCE<= I(A) UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw 0.005 =>Sink 0.01 0.015 5 of 7 QW-R105-032.B UM604/A OPERATIONAL AMPLIFIERS(Cont.) Total Harmonic Distorsion THD=F(freq) 0.014 0.012 THD(%) 0.01 0.008 0.006 0.004 10 1000 100 10000 Frequency (Hz) Noise = F (frequency) Noise (nV/SQR(Hz)) 80 60 40 20 0 10 1 0.1 0.01 Frequency (Hz) Vio Distribution-Operator 1 Vcc+=5V,Vcc-=0V 80 60 Distribution(%) LINEAR INTEGRATED CIRCUIT 40 20 0 -3 -2.5 -2 -1.5 -1 -0.5 UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw 0 Vio(mV) 0.5 1 1.5 2 2.5 3 6 of 7 QW-R105-032.B UM604/A OPERATIONAL AMPLIFIERS(Cont.) VREF (V) LINEAR INTEGRATED CIRCUIT UTC assumes no responsibility for equipment failures that result from using products at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges, or other parameters) listed in products specifications of any and all UTC products described or contained herein. UTC products are not designed for use in life support appliances, devices or systems where malfunction of these products can be reasonably expected to result in personal injury. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner. The information presented in this document does not form part of any quotation or contract, is believed to be accurate and reliable and may be changed without notice. UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw 7 of 7 QW-R105-032.B