5KP SERIES GLASS PASSIVATED JUNCTION TRANSIENT VOLTAGE SUPPRESSOR CHENG- YI ELECTRONIC VOLTAGE 5.0 to 110 VOLTS 5000 WATT PEAK PULSE POWER P600 FEATURES Plastic package has Underwrites Laboratory Flammability Classification 94V-O Glass passivated junction 5000W Peak Pulse Power capability on 10/1000 s waveform Excellent clamping capability Repetition rate (Duty Cycle):0.5% Low incremental surge resistance Fast response time: typically less than 1.0 ps from 0 volts to BV Typical ID less than 1 A above 10V High temperature soldering guaranteed: 300oC/10 seconds /.375',(9.5mm) lead length/51bs.,(2.3kg) tension MECHANICAL DATA Case:Molded plastic over glass passivated junction Terminals:Plated Axial leads, solderable per MIL-STD-750, Method 2026 Polarity:Color band denote positive end (cathode) Mounting Position:Any Weight:0.07 ounces, 2.1gram MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 250C ambient temperature unless otherwise specified. RATINGS SYMBOL VALUE UNITS PPPM Minimum 5000 Watts PPPM SEE TABLE 1 Amps Steady Power Dissipation at TL=75 C Lead Lengths .375",(9.5mm)(NOTE 2) PM(AV) 8.0 Watts Peak Forward Surge Current 8.3ms Single Half Sine-Wave Superimposed on Rated Load(JEDEC Method)(NOTE 3) IFSM 400 Amps TJ, TSTG -55 to + 175 Peak Pulse Power Dissipation on 10/1000 Peak Pulse Current of on 10/1000 s waveform (NOTE 1,Fig.1) s waveform (NOTE 1,Fig.3) 0 Operating Junction and Storage Temperature Range Notes: 1. Non-repetitive current pulse, per Fig.3 and derated above TA=25oC per Fig.2 2. Mounted on Copper Leaf area of 0.79 in2 (20mm2) 3. Measured on 8.3ms single half sine-wave or equivalent square wave, Duty Cycle=4 pulses per minuters maximum. 0 C 5KP SERIES GLASS PASSIVATED JUNCTION TRANSIENT VOLTAGE SUPPRESSOR CHENG- YI ELECTRONIC RATING AND CHARACTERISTICS CURVES 5KP SERIES Fig. 2 - PULSE DERATING CURVE PEAK PULSE POWER (P PP) OR CURRENT (l PP) DERATING PERCENTAGE % PPPM, PEAK PULSE POWER, kW Fig. 1 - PEAK PULSE POWER VS PULSE TIME 100 100 Non-Repetitive Pulse waveform Shown in Flgure 3 TA=250C 10 1.0 0.1 0.1 s 1.0 s 10 s 1.0ms 100 s 10ms td, PULSE WIDTH, SEC 75 50 25 0 0 25 TA=250C Pulse Width (td) is Defined as the Poitn Where the Peak Current Decays to 50% of Ipp 150 175 200 0 TJ=25C f=1.0MHz Vsig=50mVp-p CJ, CAPACITANCE, pF 20,000 10/1000 sec Waveform as Defined by R.E.A 50 125 40,000 Half Value-Ipp 2 e-kt Measursd at Zero Bias 10,000 6,000 Measursd at Stand-Off Voltage(V MW) 4,000 2,000 1,000 td 0 0 1.0 2.0 3.0 400 4.0 t, TIME, ms 200 Fig. 5 - STEADY STATE POWER DERATING CURVE 100 1.0 0.8 2.0 5.0 10 20 50 100 200 V(WM), REVERSE STAND-OFF VOLTAGE, VOLTS Fig. 6 - MAXIMUM NON-REPETITIVE 0.6 l=375"(9.5mm) 0.4 0.2 20mmx20mmx1mm Cu (0.8"x0.8"x.040") 0 0 25 50 75 100 125 150 TL, LEAD TEMPERATURE, 0C 175 200 IFSM, PEAK FORWARD SURGE CURRENT AMPERES Pm (AV) STEADY STATE POWER DISSIPATION, WATTS IPPM, PEAK PULSE CURRENT, % 100 100 104 150 Peak Value Ippm 75 Fig. 4 - TYPICAL JUNCTION CAPACITANCE UNIDIRECTIONAL Fig. 3 - PULSE WAVEFORM tf=10 se 50 TA, AMBIENT TEMPERATURE, 0C PEAK FORWARD SURGE CURRENT 400 TJ=TJ max 350 8.3ms Single Half Sine-Wave JEDEC Method 300 250 200 150 100 1 2 3 5 10 20 30 NUMBER OF CYCLES AT 60 Hz 50 100