SA Transient 9ROWDJH6XSSUHVVRUV Series MERITEK 6 UL E223045 FEATURES Plastic Sackage. Glass passivated chip junction. 500W Peak Pulse Power capability on 10/1000µs waveform. Excellent clamping capability. Repetition rate (duty cycle): 0.01%. Low incremental surge resistance. Fast response time: typically less than 1.0ps from 0 volt to BV for 8nidirectional and 5.0ns for %idirectional types. i Typical IR less than 1µA above 10V. DO-204AC/DO-15 6 High temperature soldering guaranteed: 265°C/10 seconds/.375", (9.5mm) lead length, 5lbs, (2.3kg) tension. ( M MECHANICAL DATA M Case: JEDEC DO-15 Molded plastic over glass passivated junction. Terminals: Plated Axial leads, solderable per MIL-STD-750, Method 2026. Polarity: Color band denotes cathode except Bidirectional. Mounting Position: Any. Weight: 0.015 ounce, 0.4grams. DEVICES FOR BIPOLAR APPLICATION For %idirectional use C or CA suffix for type SA5.0 through type SA220 (e.g. SA5.0C, SA220CA); Electrical characteristics apply in both directions. MAXIMUM RATINGS AND CHARACTERISTICS Ratings at 25ć ambient temperature unless otherwise specified. RATING SYMBOL Peak Pulse Power Dissipation on 10/1000ȝs waveform. (Note1ˈFig.1) Steady State Power Dissipation at TL =75ćˈLead length .375” (9.5mm). ( Fig.5) Peak Forward Surge Currentˈ8.3ms Single Half Sine-Wave Superimposed on Rated Load. (JEDEC Method) (Note 2, Fig.6) Operating junction and Storage Temperature Range. Notes: Minimum 500 PPPM ,PPM Peak Pulse Current on 10/1000ȝs waveform. (Note1Fig.3) VALUE UNIT Watts See Table Amps PM(AV) 3.0 Watts IFSM 70 Amps TJ , TSTG -55 to +175 ć 1. Non-repetitive current pulse, per Fig.3 and derated above TA = 25ć per Fig.2. 2. 8.3ms single half sine-wave, or equivalent square wave, Duty cycle = 4 pulses per minute maximum. All specifications are subject to change without notice. 1 Rev 7 6$ Transient 9ROWDJH6XSSUHVVRUV Series MERITEK PACKAGE DIMENSIONS d s DIA. DIA. L T L DO-204AC/DO-15 Millimeters Item Inches Min. Max. Min. Max. L 25.40 - 1.000 - T 5.80 7.60 0.230 0.300 d 2.60 3.60 0.104 0.140 s 0.71 0.86 0.028 0.034 SPECIFICATIONS Part Number Peak Reverse Reverse Breakdown Breakdown Maximum Test Voltage Pulse Leakage Stand-Off Voltage Clamping Current MIN.@IT MAX.@IT Current @VRWM Voltage Voltage @IPP VRWM (V) VBR MIN.(V) VBR MAX.(V) IT(mA) VC(V) IPP(A) IR(μA) SA5.0CA 5.0 6.40 7.00 10 9.2 55.4 600 SA6.0A SA6.0CA 6.0 6.67 7.37 10 10.3 49.5 600 SA6.5A SA6.5CA 6.5 7.22 7.98 10 11.2 45.5 400 SA7.0A SA7.0CA 7.0 7.78 8.60 10 12.0 42.5 150 SA7.5A SA7.5CA 7.5 8.33 9.21 1 12.9 39.5 50 SA8.0A SA8.0CA 8.0 8.89 9.83 1 13.6 37.5 25 SA8.5A SA8.5CA 8.5 9.44 10.40 1 14.4 35.4 10 SA9.0A SA9.0CA 9.0 10.00 11.10 1 15.4 33.1 5 SA10A SA10CA 10.0 11.10 12.30 1 17.0 30.0 3 SA11A SA11CA 11.0 12.20 13.50 1 18.2 28.0 1 SA12A SA12CA 12.0 13.30 14.70 1 19.9 25.6 1 SA13A SA13CA 13.0 14.40 15.90 1 21.5 23.7 1 SA14A SA14CA 14.0 15.60 17.20 1 23.2 22.0 1 SA15A SA15CA 15.0 16.70 18.50 1 24.4 20.9 1 SA16A SA16CA 16.0 17.80 19.70 1 26.0 19.6 1 UNI-POLAR BI-POLAR SA5.0A 2 Rev 7 6$ Transient 9ROWDJH6XSSUHVVRUV Series MERITEK Part Number Maximum Reverse Breakdown Breakdown Peak Reverse Test Voltage Voltage Clamping Stand-Off Pulse Leakage Current MIN.@IT MAX.@IT Voltage @IPP Current @VRWM Voltage VRWM (V) VBR MIN.(V) VBR MAX.(V) IT(mA) VC(V) IPP(A) IR(μA) SA17CA 17.0 18.90 20.90 1 27.6 18.5 1 SA18A SA18CA 18.0 20.00 22.10 1 29.2 17.5 1 SA20A SA20CA 20.0 22.20 24.50 1 32.4 15.7 1 SA22A SA22CA 22.0 24.40 26.90 1 35.5 14.4 1 SA24A SA24CA 24.0 26.70 29.50 1 38.9 13.1 1 SA26A SA26CA 26.0 28.90 31.90 1 42.1 12.1 1 SA28A SA28CA 28.0 31.10 34.40 1 45.4 11.2 1 SA30A SA30CA 30.0 33.30 36.80 1 48.4 10.5 1 SA33A SA33CA 33.0 36.70 40.60 1 53.3 9.6 1 SA36A SA36CA 36.0 40.00 44.20 1 58.1 8.8 1 SA40A SA40CA 40.0 44.40 49.10 1 64.5 7.9 1 SA43A SA43CA 43.0 47.80 52.80 1 69.4 7.3 1 SA45A SA45CA 45.0 50.00 55.30 1 72.7 7.0 1 SA48A SA48CA 48.0 53.30 58.90 1 77.4 6.6 1 SA51A SA51CA 51.0 56.70 62.70 1 82.4 6.2 1 SA54A SA54CA 54.0 60.00 66.30 1 87.1 5.9 1 SA58A SA58CA 58.0 64.40 71.20 1 93.6 5.4 1 SA60A SA60CA 60.0 66.70 73.70 1 96.8 5.3 1 SA64A SA64CA 64.0 71.10 78.60 1 103.0 5.0 1 SA70A SA70CA 70.0 77.80 86.00 1 113.0 4.5 1 SA75A SA75CA 75.0 83.30 92.10 1 121.0 4.2 1 SA78A SA78CA 78.0 86.70 95.80 1 126.0 4.0 1 SA85A SA85CA 85.0 94.40 104.00 1 137.0 3.7 1 SA90A SA90CA 90.0 100.00 111.00 1 146.0 3.5 1 SA100A SA100CA 100.0 111.00 123.00 1 162.0 3.1 1 SA110A SA110CA 110.0 122.00 135.00 1 177.0 2.9 1 SA120A SA120CA 120.0 133.00 147.00 1 193.0 2.6 1 SA130A SA130CA 130.0 144.00 159.00 1 209.0 2.4 1 SA150A SA150CA 150.0 167.00 185.00 1 243.0 2.1 1 SA160A SA160CA 160.0 178.00 197.00 1 259.0 2.0 1 SA170A SA170CA 170.0 189.00 209.00 1 275.0 1.9 1 SA180A SA180CA 180.0 198.00 233.00 1 289.0 1.7 1 SA190A SA190CA 190.0 209.00 243.20 1 308.0 1.6 1 SA200A SA200CA 200.0 220.00 256.00 1 324.0 1.5 1 SA210A SA210CA 210.0 231.00 268.80 1 340.0 1.5 1 SA220A SA220CA 220.0 242.00 281.60 1 356.0 1.4 1 UNI-POLAR BI-POLAR SA17A Note: For Bidirectional type having VRWM of 10 volts and less,the IR limit doubles. 3 Rev 7 6$ Transient 9ROWDJH6XSSUHVVRUV Series MERITEK (TA: 25°C UNLESS OTHERWISE SPECIFIED) RATING AND CHARACTERISTIC CURVES Figure 1 - Peak Pulse Power Rating Curve 100 30 Non-repetitive Pulse Waveform Shown in Fig. 3 TA=25ûC Peak Pulse Power (PPP) or Current (IPP) Derating in Percentage, % PPPM- Peak Pulse Power (KW) Figure 2 - Pulse Derating Curve 10 Exponential P 1 P P Td Td Half SINE Square Td 0.1 01.μs 1.0μs 10μs 100μs 1.0ms 75 50 25 0 10ms 0 td- Pulse Width (sec.) 75 100 125 150 175 200 Figure 4 - Typical Junction Capacitance 10000 150 tr=10μsec TJ=25°C Pulse Width(td) is defined as the point where the peak current decays to 50% of IPPM Peak Value IPPM 100 Bi-directional V=0V Uni-directional V=0V 1000 Uni-directional @ VR Cj (pF) IPPM- Peak Pulse Current, % IRSM 50 TA- Ambient Temperature (ºC) Figure 3 - Pulse Waveform Half Value IPPM IPPM ( ) 2 100 Bi-directional @ VR 50 10/1000μsec. Waveform as defined by R.E.A 10 Tj=25C f=1.0MHz Vsig=50mVp-p td 0 1.0 0 2.0 3.0 1 1.0 4.0 10.0 100.0 1000.0 VBR - Reverse Breakdown Voltage (V) t-Time (ms) Figure 6 - Maximum Non-Repetitive Forward Surge Current Uni-Directional Only Figure 5 - Steady State Power Dissipation Derating Curve 3.5 80 3 IFSM - Peak Forward Surge Current (A) Steady State Power Dissipation (W) 25 2.5 2 1.5 1 0.5 70 60 50 40 30 20 10 0 0 25 50 75 100 125 150 175 0 200 1 TL - Lead Temperature(ºC) 4 10 Number of Cycles at 60 Hz 100 Rev 7