Document 110-1 5 mm Tunable Inductor – 164, 165 Series • These tunables offer the compactness of a 5 mm coil and the low drift reliability of an insert molded coil. • Inductance values from 9 to over 280 nH • Optional plated brass cans provide integral shielding • Can be ordered without cores for use as fixed inductors Designer’s Kit M305 contains 2 each of all parts Core material Aluminum, 0.187″ (4.75 mm) long. Terminations Leads: RoHS compliant tin-silver over copper. Other terminations available at additional cost. Shield can tabs: Tin-silver over nickel over brass Weight 164 series unshielded: 0.16 – 0.31 g; with shield can: 0.45 – 0.60 g 165 series unshielded: 0.15 – 0.25 g; with shield can: 0.43 – 0.54 g Ambient temperature –40°C to +85°C Storage temperature Component: –40°C to +85°C. Packaging: –40°C to +80°C Resistance to soldering heat: Wave solder only. Recommended maximum board surface temperature of 168°C (334°F) for no more than three seconds. Pre-heating is recommended to minimize time over the solder nozzle. Moisture Sensitivity Level (MSL) 1 (unlimited floor life at <30°C / 85% relative humidity) Failures in Time (FIT) / Mean Time Between Failures (MTBF) Two per billion hours / 1/2 billion hours, calculated per Telcordia SR-332 Packaging 50 parts per tube PCB washing Only pure water or alcohol recommended IN 1 TRITUNER 3 TOOLS SEE INDEX TUNING WRENCH Unshielded Styles 0.139 ±0.005 3,53 ±0,13 0.130 ±0.040 3,30 ±1,02 0.310 ±0.020 7,87 ±0,51 0.139 ±0.005 3,53 ±0,13 Start 0.018 dia 0,46 0.205 ±0.005 square 5,21 ±0,13 Shielded Styles Recommended Board Layout 0.0695 1,765 0.051 (for shield 1,30 can tabs) 0.340 max 8,64 0.120 ±0.010 3,05 ±0,25 Tab length Finish 0.106 2,69 CL Part marking this side Start 0.031 ±0.010 0,79 ±0,25 Series number Specifications subject to change without notice. Please check our website for latest information. © Coilcraft, Inc. 2009 0.120 dia hole 3,05 165-XX XXXX CL 0.0695 1,765 0.038 0,965 0.212 Tab centers 5,38 Internal code Dash number Document 110-1 0.230 square max 5,84 Revised 08/31/09 Document 110-2 5 mm Tunable Inductor — Unshielded No core at L max3 at L min4 2 5 2 5 L (nH) Q min L (nH) Q min L (nH)2 Q min5 Part number1 Color Turns 164-01A06L 164-02A06L 164-03A06L 164-04A06L 164-05A06L 164-06A06L 164-07A06L 164-08A06L 164-09A06L 164-10A06L 164-11A06L Brown Red Orange Yellow Green Blue Violet Gray White Black Brown 11/2 21/2 31/2 41/2 51/2 61/2 71/2 81/2 91/2 101/2 111/2 19 34 55 77 101 128 156 183 216 248 281 145 138 130 119 108 107 106 100 100 92 92 19 34 55 77 99 126 150 178 190 223 246 145 138 130 119 86 75 68 62 62 55 55 16 26 38 52 65 83 97 112 131 148 170 165-00A06L 165-01A06L 165-02A06L 165-03A06L 165-04A06L 165-05A06L 165-06A06L 165-07A06L Black Brown Red Orange Yellow Green Blue Violet 1/ 2 11/2 21/2 31/2 41/2 51/2 61/2 71/2 9 18 32 48 64 83 103 122 147 145 143 138 133 125 120 115 9 18 32 45 60 78 90 105 147 145 143 135 114 110 94 92 9 15 25 33 43 54 68 79 No core SRF min (MHz) Irms6 (A) 112 96 79 72 64 60 57 53 53 51 51 150 150 150 150 150 100 100 100 100 100 100 2000 1260 960 850 770 730 640 570 540 490 360 7.2 5.1 4.4 3.7 3.6 3.3 3.1 2.9 2.7 2.5 2.3 131 112 92 84 76 73 70 69 150 150 150 150 150 150 150 150 6000 2850 1860 1410 1130 820 800 770 8.1 6.5 4.9 4.2 3.8 3.6 3.4 3.1 Typical Q vs Frequency 164 Series No Core 164 Series Al Core 180 180 160 160 140 140 01 120 100 11 120 03 05 Q factor 1. To order fixed inductance parts without cores, eliminate the “A06”, e.g. 164-01. 2. Inductance measured on Agilent/HP 4286A Impedance Analyzer with 16092A Spring Clip Fixture. 3. L max measured with core halfway out top of form. 4. L min measured with core centered in winding. 5. Q measured on Agilent/HP 4286A with 16092A fixture, direct connect to Agilent/HP 4342A Q-Meter and Meguro MQ-171 Q-Meter with 0.5″ bus bars. 6. Current that causes a 15°C rise above 25°C ambient. 7. Electrical specifications 25°C. See Qualification Standards section for environmental and test data. Q factor Notes: Freq (MHz) 07 80 80 60 60 40 40 20 20 10 01 100 03 05 11 10 20 40 60 80 100 200 400 20 40 Frequency (MHz) 165 Series No Core 200 400 165 Series Al Core 160 160 00 140 04 120 140 02 00 120 07 Q factor Q factor 80 100 180 180 100 80 100 02 80 04 60 60 40 40 20 20 07 10 10 20 40 60 80 100 200 400 Frequency (MHz) Specifications subject to change without notice. Please check our website for latest information. © Coilcraft, Inc. 2009 60 Frequency (MHz) 20 40 60 80 100 200 400 Frequency (MHz) Document 110-2 Revised 08/31/09 Document 110-3 IN 1 TRITUNER 3 TOOLS SEE INDEX TUNING WRENCH 5 mm Tunable Inductor — Shielded No core at L max3 at L min4 2 5 2 5 L (nH) Q min L (nH) Q min L (nH)2 Q min5 Part number1 Color Turns 164-01A06SL 164-02A06SL 164-03A06SL 164-04A06SL 164-05A06SL 164-06A06SL 164-07A06SL 164-08A06SL 164-09A06SL 164-10A06SL 164-11A06SL Brown Red Orange Yellow Green Blue Violet Gray White Black Brown 11/2 21/2 31/2 41/2 51/2 61/2 71/2 81/2 91/2 101/2 111/2 16 27 41 56 71 88 105 122 141 160 179 124 108 92 86 80 79 75 74 71 69 69 16 27 41 56 71 80 101 117 134 150 164 124 108 92 84 79 77 70 64 62 60 60 14 22 32 43 53 65 76 87 100 113 127 165-00A06SL 165-01A06SL 165-02A06SL 165-03A06SL 165-04A06SL 165-05A06SL 165-06A06SL 165-07A06SL Black Brown Red Orange Yellow Green Blue Violet 1/ 2 11/2 21/2 31/2 41/2 51/2 61/2 71/2 9 16 25 35 46 57 68 80 138 124 110 104 97 92 86 85 9 16 25 33 41 50 59 70 138 124 110 102 90 82 75 74 9 14 21 28 35 43 52 60 No core SRF min (MHz) Irms6 (A) 106 89 72 66 60 59 54 54 53 51 51 150 150 150 150 150 150 100 100 100 100 100 2100 1300 1100 940 980 800 750 580 550 490 400 7.2 5.1 4.4 3.7 3.6 3.3 3.1 2.9 2.7 2.5 2.3 121 104 87 78 69 67 65 64 150 150 150 150 150 150 150 150 6000 2570 1670 1230 1150 820 800 770 8.1 6.5 4.9 4.2 3.8 3.6 3.4 3.1 Typical Q vs Frequency 164 Series No Core 164 Series Al Core 180 180 160 160 140 140 120 120 01 Q factor 1. To order fixed inductance parts without cores, eliminate the “A06”, e.g. 164-01S. 2. Inductance measured on Agilent/HP 4286A Impedance Analyzer with 16092A Spring Clip Fixture. 3. L max measured with core halfway out top of form. 4. L min measured with core centered in winding. 5. Q measured on Agilent/HP 4286A with 16092A fixture, direct connect to Agilent/HP 4342A Q-Meter and Meguro MQ-171 Q-Meter with 0.5″ bus bars. 6. Current that causes a 15°C rise above 25°C ambient. 7. Electrical specifications 25°C. See Qualification Standards section for environmental and test data. Q factor Notes: Freq (MHz) 100 03 80 05 60 11 01 100 80 03 60 40 40 20 20 10 05 11 10 20 40 60 80 100 200 400 20 40 Frequency (MHz) 165 Series No Core 200 400 165 Series Al Core 160 160 00 140 140 120 120 02 100 Q factor Q factor 80 100 180 180 04 07 80 00 100 02 80 60 60 40 40 20 20 04 07 10 10 20 40 60 80 100 200 400 Frequency (MHz) Specifications subject to change without notice. Please check our website for latest information. © Coilcraft, Inc. 2009 60 Frequency (MHz) 20 40 60 80 100 200 400 Frequency (MHz) Document 110-3 Revised 08/31/09