COMMERCIAL LASERS Continuous Wave 532 nm Diode-Pumped Solid State Laser CDPS532S Key Features • Compact • Robust design • Low noise • Excellent beam quality • High reliability Applications • DNA sequencing • Flow cytometry • Capillary electrophoreses • Instrumentation The JDSU CDPS532S is a compact, continuous wave, 532 nm, diode-pumped solid-state laser. The system features a laser head and multi-function controller that requires a 5 V DC power source. It provides 10 and 20 mW of optical power with remarkable beam quality and low noise. One of the key benefits of the CDPS532S is its compact and efficient design, which makes it easy to integrate into OEM instrumentation. The laser head does not incorporate beam shaping optics to allow for the smallest possible packaging. The CDPS532S laser controller is also very compact and efficient enough to forgo additional heat sinking. The CDPS532S laser head features an improved cavity design for longer lifetime and reliability. Its mechanical design requires fewer parts and is therefore ideally suited for high volume manufacturing techniques. Overall, the CDPS532S laser's sophisticated new design results in exceptional optical performance from a rugged package with superior long term stability. Easy to operate and to integrate, the controller interface provides several control functions, including interlock and diagnostics via transistor-to-transistor logic (TTL) and analog signals. NORTH AMERICA : 800 498-JDSU (5378) WORLDWIDE : +800 5378-JDSU WEBSITE : www.jdsu.com CDPS532S 2 Dimensions Diagram: Controller (Specifications in mm unless otherwise noted.) ATI Controller Assembly Ø4 (4X) 111 100.80 63 50.40 21.90 CDPS532S 3 Dimensions Diagram: Laser Head (Specifications in mm unless otherwise noted.) CLEARANCE AND C'BORE FOR 4X #6-32 X 1.5 CAP SCREW DANGER 15 PIN HIGH DENSITY D-SUB CONNECTOR BEAM IS POLARIZED ORTHOGONAL TO MOUNTING SURFACE (>100:1) ± 5° 28.854 R1.588 14.427 SERIAL NO. MANUFACTURED MODEL 25.400 Ø 4.978 HEAT DISSIPATED FROM THIS SURFACE 28.550 2X R 1.600 4X Ø 4.039 19.050 28.550 4.750 3.175 69.850 76.200 4X 4.49 CHAM TYP 39.827 CDPS532S 4 Specifications Parameter Optical Wavelength Output power CDPS532S-010 CDPS532S-020 Power stability (1 hour, 25±3 °C) Mode quality M2 Beam diameter (1/e2 point, at a distance of 250 mm) Beam divergence (full angle) Polarization ratio (E-vector is vertical) Noise (rms, 20 Hz to 1 MHz) Ellipticity Pointing stability (after 2 hour warm-up, 25±3 °C) Static alignment Beam position Beam angle Environmental Base plate temperature Operating Non-operating Shock (11 ms duration) Operating Non-operating Vibration (sinusoidal, 5 to 500 Hz) Operating Non-operating Heat sink requirements Surface flatness Torque specification Specification 532 ± 1 nm 10 mW 20 mW <1.5% <1.3 1.9±0.2 mm <8 mrad >100:1 <0.5% <10% ±30 µrad ±1.0 mm ±1.5 ° 10 to 45 °C 0 to 60 °C 1g 25 g 0.3 g 2g 25 µm 0.5 Nm CDPS532S 5 Cooling Requirements 7 6 Heat Load (W) Follow these cooling recommendations when integrating the laser into an original equipment manufacturer (OEM) system or application. The laser head is mounted to a heat sink for proper operation. The maximum base plate temperature is maintained below 45°C. The recommended heat sink capacity at a temperature of 45°C is 10 W. The required heat sink properties are estimated with this chart (right). 5 4 3 2 1 0 25 30 35 40 45 50 55 Base Plate Temperature (ºC) Ordering Information For more information on this or other products and their availability, please contact your local JDSU account manager or JDSU directly at 1-800-498-JDSU (5378) in North America and +800-5378-JDSU worldwide or via e-mail at [email protected]. Sample: CDPS532S-010 CDPS532SCode 010 020 Output Power 10 mW 20 mW CDPS532S Compliance with Regulatory Requirements The CDPS532S laser system is an OEM version of a JDSU diode-pumped solid state laser. As such, it is intended only for integration into other equipment. The CDPS532S laser does not comply with Center for Devices and Radiological Health (CDRH) standards. The customer is responsible for CDRH certification of any system that incorporates the CDPS532S laser. Warranty JDSU diode-pumped solid state lasers are warranted to be free of defects in materials and workmanship for 12 months from the date of shipment, or 5,000 hours, whichever comes first. LASER RADIATION IS EMITTED FROM THIS APERTURE AVOID EXPOSURE LASER RADIATION AVOID EXPOSURE TO BEAM CLASS 3B LASER PRODUCT (IEC) CLASS IIIb LASER PRODUCT (CDRH) 532NM / MAXIMUM POWER 500 mW THIS LASER DOES NOT COMPLY WITH 21 CFR 1040 OR IEC 825. USE ONLY AS A COMPONENT 02-000760_501 All statements, technical information and recommendations related to the products herein are based upon information believed to be reliable or accurate. However, the accuracy or completeness thereof is not guaranteed, and no responsibility is assumed for any inaccuracies. The user assumes all risks and liability whatsoever in connection with the use of a product or its application. JDSU reserves the right to change at any time without notice the design, specifications, function, fit or form of its products described herein, including withdrawal at any time of a product offered for sale herein. JDSU makes no representations that the products herein are free from any intellectual property claims of others. Please contact JDSU for more information. JDSU and the JDSU logo are trademarks of JDS Uniphase Corporation. Other trademarks are the property of their respective holders. ©2006 JDS Uniphase Corporation. All rights reserved. 10132857 Rev. 003 02/06 CDPS532S.DS.CL.AE NORTH AMERICA : 800 498-JDSU (5378) WORLDWIDE : +800 5378-JDSU WEBSITE : www.jdsu.com