JDSU FCD488FC-020

COMMERCIAL LASERS
Continuous Wave 488 nm Solid-State Laser
FCD488
Key Features
• Compact – optics and electronics integrated in one housing
• Low heat load – no heat sink required
• Good efficiency – requires only small 5 V power supply
• Fiber-based architecture – enables fiber-delivered version
• High reliability – due to telecom-style packaging technology
Applications
• Biotechnology
• Semiconductor instrumentation
• General instrumentation
The FCD488 is a continuous wave 10, 20 and 25 mW 488 nm solid-state laser,
featuring fiber-based architecture. The package contains both the optical elements
of the laser and the control electronics, allowing full control and diagnostics of the
laser system through an analog interface and RS232 interface. Powered by an
external 5 V DC power supply, the laser is cost-efficient, reliable, and compact,
with excellent electrical and thermal efficiency. It has a low heat load, so the laser
operates without a heat sink.
Based on JDSU’s Frequency Converted Diode technology, the FCD488 enables
consistent high volume laser manufacturing, with a “package, splice, and test”
design. The components are put in hermetic packaging. The fibers are spliced
together. And the laser is tested.
The FCD488 is available in two versions: a free space and a fiber-delivered version
with the same characteristics and reliability as the free space laser.
NORTH AMERICA : 800 498-JDSU (5378)
WORLDWIDE : +800 5378-JDSU
WEBSITE : www.jdsu.com
CONTINUOUS WAVE 488 NM SOLID-STATE LASER
2
Dimensions Diagram
(Specifications in mm unless otherwise noted.)
125
115.0
5.0
COMMUNICATION PORT
15-PIN D-SUB CONNECTOR
7.5
5 V PO WER SUP PL Y
13.8
55.0
70
17.5
LA S E R S T A T U S
2 LEDS
4X 4.0
THRU
10.1
11.5
19.0
34
5.5
Free Space
COMMUNICATION PORT
15-PIN D-SUB CONNECTOR
1.5M HARNESS LENGTH
68 ROM LENGTH
7.5
5V POWER SUPPLY
55.0
70
12.7
20
LASER STATUS
2 LEDS
4X 4.0
THRU
115.0
125
34
5.5
Fiber Delivered
5.0
22
CONTINUOUS WAVE 488 NM SOLID-STATE LASER
3
Specifications
Parameter
Optical
Wavelength
Output power
Power stability (2 hour, 25±3 °C) after warm-up
Mode quality M2
Beam diameter (1/e2 point)
Beam divergence (full angle)
Polarization ratio (E-vector is vertical)
Noise (rms, 20 Hz to 2 MHz)
Ellipticity
Pointing stability after warm-up
Static alignment
Beam position
Beam angle
Environmental
Base plate temperature
Operating
Non-operating
Shock (11 ms duration)
Operating
Non-operating
Vibration (sinusoidal, 5 to 500 Hz)
Operating
Non-operating
Warm-up time
Electrical requirements
Operating voltage
Current required
FCD488-010
(Free Space)
FCD488-020
(Free Space)
10 mW
20 mW
± 0.25 mm
± 2.5 mrad
± 0.25 mm
± 2.5 mrad
FCD488-025
(Free Space)
FCD488FC-010 FCD488FC-020
(Fiber Delivered) (Fiber Delivered)
488 ± 2 nm
25 mW
10 mW
<2.0%
<1.2
0.7 mm ± 10%
<1.0 mrad
>100:1
<0.5%
<10%
<10 µrad/°C
± 0.25 mm
± 2.5 mrad
± 0.5 mm
± 50 mrad
20 mW
± 0.5 mm
± 50 mrad
10 to 45°C
0 to 60°C
1g
25 g
0.3 g
2g
<10 minutes
5.0 ± 0.4 V DC
4A
Ordering Information
For more information on this or other products and their availability, please contact your local JDSU account manager or
JDSU directly at 1-800-498-JDSU (5378) in North America and +800-5378-JDSU worldwide, or via e-mail at
[email protected].
Sample: FCD488-010
Product Code
FCD488-010
FCD488-020
FCD488-025
FCD488FC-010
FCD488FC-020
Description
FCD continuous wave 10 mW 488 nm free space solid-state laser
FCD continuous wave 20 mW 488 nm free space solid-state laser
FCD continuous wave 25 mW 488 nm free space solid-state laser
FCD continuous wave 10 mW 488 nm fiber delivered solid-state laser
FCD continuous wave 20 mW 488 nm fiber delivered solid-state laser
CONTINUOUS WAVE 488 NM SOLID-STATE LASER
Compliance with Regulatory Requirements
The FCD488 laser system is an OEM version of a JDSU solid-state laser and as such only intended for integration into other
equipment. These lasers do not comply with CDRH. The customer is responsible for CDRH certification of the system
incorporating the FCD488 laser system.
The unit has been designed and tested to comply with the following standards:
Electromagnetic radiated and line conducted emissions tested to standard EN 55022.
Electromagnetic immunity tested to standard EN 61326 in compliance with IEC 601010-1 and IEC 60825-1.
Warranty
JDSU FCD488 solid-state lasers are warranted to be free of defects in materials
and workmanship for twelve months from the date of shipment or 5,000
hours, whichever occurs first.
NORTH AMERICA : 800 498-JDSU (5378)
WORLDWIDE : +800 5378-JDSU
Product specifications and descriptions in this document subject to change without notice. © 2009 JDS Uniphase Corporation 30149042 003 0309
WEBSITE : www.jdsu.com
FCD488.DS.CL.AE
March 2009