TI SN75179BD

SN75179B
DIFFERENTIAL DRIVER AND RECEIVER PAIR
SLLS003E – OCTOBER 1985 – REVISED JUNE 1998
D
D
D
D
D
D
D
D
D
D
D OR P PACKAGE
(TOP VIEW)
Meets or Exceeds the Requirements of
TIA/EIA-422-B, TIA/EIA-485-A, and ITU
Recommendation V.11
Bus Voltage Range . . . – 7 V to 12 V
Positive- and Negative-Current Limiting
Driver Output Capability . . . 60 mA Max
Driver Thermal-Shutdown Protection
Receiver Input Impedance . . . 12 kΩ Min
Receiver Input Sensitivity . . . ± 200 mV
Receiver Input Hysteresis . . . 50 mV Typ
Operates From Single 5-V Supply
Low Power Requirements
VCC
R
D
GND
1
8
2
7
3
6
4
5
A
B
Z
Y
description
The SN75179B is a differential driver and receiver pair designed for balanced transmission-line applications
and meets TIA/EIA-422-B, TIA/EIA-485-A, and ITU Recommendation V.11. It is designed to improve the
performance of full-duplex data communications over long bus lines.
The SN75179B driver output provides limiting for both positive and negative currents. The receiver features high
input impedance, input hysteresis for increased noise immunity, and input sensitivity of ± 200 mV over a
common-mode input voltage range of – 7 V to 12 V. The driver provides thermal shutdown for protection from
line fault conditions. Thermal shutdown is designed to occur at a junction temperature of approximately 150°C.
The SN75179B is designed to drive current loads of up to 60 mA maximum.
The SN75179B is characterized for operation from 0°C to 70°C.
Function Tables
DRIVER
INPUT
D
OUTPUTS
Y
Z
H
H
L
L
L
H
RECEIVER
DIFFERENTIAL INPUTS
A–B
OUTPUT
R
VID ≥ 0.2 V
– 0.2 V < VID < 0.2 V
H
VID ≤ – 0.2 V
L
Open
?
?
H = high level, L = low level, ? = indeterminate
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
Copyright  1998, Texas Instruments Incorporated
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of Texas Instruments
standard warranty. Production processing does not necessarily include
testing of all parameters.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
1
SN75179B
DIFFERENTIAL DRIVER AND RECEIVER PAIR
SLLS003E – OCTOBER 1985 – REVISED JUNE 1998
logic symbol†
logic diagram (positive logic)
8
2
7
R
6
3
5
D
8
A
B
R
2
7
A
B
Z
6
Y
D
3
5
† This symbol is in accordance with ANSI/IEEE Std 91-1984
and IEC Publication 617-12.
Z
Y
schematics of inputs and outputs
EQUIVALENT OF DRIVER INPUT
TYPICAL OF ALL DRIVER OUTPUTS
VCC
VCC
Input
Output
GND
Driver input: R(eq) = 3 kΩ NOM
R(eq) = equivalent resistor
EQUIVALENT OF EACH RECEIVER INPUT
TYPICAL OF ALL RECEIVER OUTPUTS
VCC
VCC
85 Ω
NOM
960 Ω
NOM
Input
16.8 kΩ
NOM
2
960 Ω
NOM
Output
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
SN75179B
DIFFERENTIAL DRIVER AND RECEIVER PAIR
SLLS003E – OCTOBER 1985 – REVISED JUNE 1998
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)†
Supply voltage, VCC (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Voltage range at any bus terminal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 10 V to 15 V
Differential input voltage, VID (see Note 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ± 25 V
Package thermal impedance, θJA (see Note 3): D package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 197°C/W
P package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104°C/W
Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 65°C to 150°C
Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 260°C
† Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
NOTES: 1. All voltage values, except differential input voltage, are with respect to network ground terminal.
2. Differential input voltage is measured at the noninverting input with respect to the corresponding inverting input.
3. The package thermal impedance is calculated in accordance with JESD 51, except for through-hole packages, which use a trace
length of zero.
recommended operating conditions
Supply voltage, VCC
High-level input voltage, VIH
Driver
Low-level input voltage, VIL
Driver
MAX
UNIT
5
5.25
V
–7‡
Differential input voltage, VID
Low level output current,
Low-level
current IOL
NOM
2
Common-mode input voltage, VIC
High level output current,
High-level
current IOH
MIN
4.75
Driver
Receiver
Driver
V
0.8
V
12
V
± 12
V
– 60
mA
– 400
µA
60
Receiver
8
mA
Operating free-air temperature, TA
0
70
°C
‡ The algebraic convention, where the less positive (more negative) limit is designated minimum, is used in this data sheet for common-mode input
voltage and threshold voltage.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
3
SN75179B
DIFFERENTIAL DRIVER AND RECEIVER PAIR
SLLS003E – OCTOBER 1985 – REVISED JUNE 1998
DRIVER SECTION
electrical characteristics over recommended ranges of supply voltage and operating free-air
temperature (unless otherwise noted)
PARAMETER
TEST CONDITIONS
VIK
Input clamp voltage
II = - 18 mA
VO
VOD1 
Output voltage
IO = 0
Differential output voltage
IO = 0
VOD2 
g
Differential output voltage
VOD3 
Differential output voltage
∆VOD 
Change in magnitude of common-mode
output voltage§
VOC
Common-mode output voltage
∆VOC 
Change in magnitude of common-mode
output voltage§
IO
IIH
Output current
IIL
Low-level input current
IOS
MIN
V
6
V
1.5
6
V
See Figure 1
RL = 54 Ω,
See Figure 1
1.5
V
2.5
1.5
VCC = 0,
VI = 2.4 V
High-level input current
See Figure 1
VO = – 7 V to 12 V
VI = 0.4 V
VO = – 7 V
Short circuit output current
Short-circuit
UNIT
– 1.5
RL = 100 Ω,
RL = 54 Ω or 100 Ω,
MAX
0
1/2VOD1
or 2‡
See Note 4
TYP†
5
V
5
V
± 0.2
V
3
–1
V
± 0.2
V
± 100
µA
20
µA
– 200
µA
– 250
VO = VCC or 12 V
No load
250
mA
ICC
Supply current (total package)
57
70
mA
† All typical values are at VCC = 5 V and TA = 25°C.
‡ The minimum VOD2 with 100-Ω load is either 1/2 VOD2 or 2 V, whichever is greater.
§ ∆|VOD| and ∆|VOC| are the changes in magnitude of VOD and VOC, respectively, that occur when the input changes from a high level to a low
level.
NOTE 4: See TIA/EIA-485-A, Figure 3.5, Test Termination Measurement 2.
switching characteristics, VCC = 5 V, TA = 25°C
PARAMETER
td(OD)
tt(OD)
TEST CONDITIONS
Differential output delay time
RL = 54 Ω
Ω,
Differential output transition time
MIN
TYP
MAX
15
22
ns
20
30
ns
See Figure 3
Symbol Equivalents
DATA-SHEET PARAMETER
TIA/EIA-422-B
VO
| VOD1 |
Voa, Vob
Vo
Voa, Vob
Vo
| VOD2 |
Vt (RL = 100 Ω)
Vt (RL = 54 Ω)
Vt (Test Termination Measurement 2)
∆ | VOD |
| | Vt | – |Vt | |
| | Vt | – |Vt | |
VOC
∆ | VOC |
| Vos |
| Vos |
| Vos – Vos |
| Vos – Vos |
IOS
IO
| Isa |, | Isb |
| VOD3 |
4
TIA/EIA-485-A
| Ixa |, | Ixb |
POST OFFICE BOX 655303
Iia , Iib
• DALLAS, TEXAS 75265
UNIT
SN75179B
DIFFERENTIAL DRIVER AND RECEIVER PAIR
SLLS003E – OCTOBER 1985 – REVISED JUNE 1998
RECEIVER SECTION
electrical characteristics over recommended ranges of common-mode input voltage, supply
voltage, and operating free-air temperature (unless otherwise noted)
PARAMETER
TEST CONDITIONS
VIT +
VIT –
Positive-going input threshold voltage
Vhys
VOH
Hysteresis voltage (VIT + – VIT –)
VOL
Low-level output voltage
Negative-going input threshold voltage
High-level output voltage
II
Line input current
ri
Input resistance
VO = 2.7 V,
VO = 0.5 V,
MIN
IO = – 0.4 mA
IO = 8 mA
TYP†
MAX
0.2
– 0.2‡
IOH = – 400 µA,
IOL = 8 mA,
Other input at 0 V
V,
See Figure 2
mV
2.7
V
See Figure 2
0.45
VI = 12 V
VI = – 7 V
See Note 5
V
V
50
VID = 200 mV,
VID = – 200 mV,
UNIT
1
– 0.8
12
V
mA
kΩ
IOS
Short-circuit output current
– 15
– 85
mA
ICC
Supply current (total package)
No load
57
70
mA
† All typical values are at VCC = 5 V, TA = 25°C.
‡ The algebraic convention, where the less positive (more negative) limit is designated minimum, is used in this data sheet for common-mode input
voltage and threshold voltage levels only.
NOTE 5: Refer to TIA/EIA-422-B for exact conditions.
switching characteristics, VCC = 5 V, TA = 25°C
PARAMETER
tPLH
tPHL
TEST CONDITIONS
Propagation delay time, low- to high-level output
VID = – 1.5 V to 1.5 V,
CL = 15 pF,
See Figure 4
Propagation delay time, high- to low-level output
MIN
TYP
MAX
19
35
UNIT
ns
30
40
ns
PARAMETER MEASUREMENT INFORMATION
RL
2
VOD2
RL
2
VOC
Figure 1. Driver VDD and VOC
VID
VOL
VOH
+ IOL
– IOH
Figure 2. Receiver VOH and VOL
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
5
SN75179B
DIFFERENTIAL DRIVER AND RECEIVER PAIR
SLLS003E – OCTOBER 1985 – REVISED JUNE 1998
PARAMETER MEASUREMENT INFORMATION (CONTINUED)
3V
Input
RL = 54 Ω
Generator
(see Note A)
50 Ω
CL = 50 pF
(see Note B)
Output
1.5 V
1.5 V
0V
td(OD)
Output
td(OD)
90%
10%
50%
≈ 2.5 V
50%
≈ – 2.5 V
tt(OD)
tt(OD)
TEST CIRCUIT
VOLTAGE WAVEFORMS
NOTES: A. The input pulse is supplied by a generator having the following characteristics: PRR ≤ 1 MHz, 50% duty cycle, tr ≤ 6 ns,
tf ≤ 6 ns, ZO = 50 Ω.
B. CL includes probe and jig capacitance.
Figure 3. Driver Test Circuit and Voltage Waveforms
Input
Generator
(see Note A)
50 Ω
3V
1.5 V
1.5 V
0V
Output
1.5 V
CL = 50 pF
(see Note B)
tPLH
tPHL
VOH
Output
1.3 V
1.3 V
VOL
TEST CIRCUIT
VOLTAGE WAVEFORMS
NOTES: A. The input pulse is supplied by a generator having the following characteristics: PRR ≤ 1 MHz, 50% duty cycle, tr ≤ 6 ns,
tf ≤ 6 ns, ZO = 50 Ω.
B. CL includes probe and jig capacitance.
Figure 4. Receiver Test Circuit and Voltage Waveforms
6
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
SN75179B
DIFFERENTIAL DRIVER AND RECEIVER PAIR
SLLS003E – OCTOBER 1985 – REVISED JUNE 1998
TYPICAL CHARACTERISTICS
DRIVER
DRIVER
HIGH-LEVEL OUTPUT VOLTAGE
vs
HIGH-LEVEL OUTPUT CURRENT
LOW-LEVEL OUTPUT VOLTAGE
vs
LOW-LEVEL OUTPUT CURRENT
5
VCC = 5 V
TA = 25°C
4.5
VCC = 5 V
TA = 25°C
4.5
VOL – Low-Level Output Voltage – V
VOH – High-Level Output Voltage – V
5
4
3.5
3
2.5
2
1.5
1
4
3.5
3
2.5
2
1.5
1
0.5
0.5
0
0
0
– 20
– 40
– 60
– 80
– 100
0
– 120
IOH – High-Level Output Current – mA
80
100
20
40
60
IOL – Low-Level Output Current – mA
Figure 5
Figure 6
DRIVER
RECEIVER
DIFFERENTIAL OUTPUT VOLTAGE
vs
OUTPUT CURRENT
OUTPUT VOLTAGE
vs
DIFFERENTIAL INPUT VOLTAGE
4
5
VCC = 5 V
TA = 25°C
3.5
4.5
VCC = 5 V
IO = 0
TA = 25°C
4
3
VO – Output Voltage – V
VOD – Differential Output Voltage – V
120
2.5
2
1.5
3.5
VIC =
–12 V
VIC =
0
VIT–
VIT–
VIC =
12 V
3
VIT–
2.5
2
VIT+
VIT+
VIT+
1.5
1
1
0.5
0
0.5
0
10
20
30 40 50 60 70 80
IO – Output Current – mA
90
100
0
–125 –100 –75 – 50 – 25 0
25 50 75 100 125
VID – Differential Input Voltage – mV
Figure 8
Figure 7
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
7
SN75179B
DIFFERENTIAL DRIVER AND RECEIVER PAIR
SLLS003E – OCTOBER 1985 – REVISED JUNE 1998
TYPICAL CHARACTERISTICS
HIGH-LEVEL OUTPUT VOLTAGE
vs
FREE-AIR TEMPERATURE
HIGH-LEVEL OUTPUT VOLTAGE
vs
HIGH-LEVEL OUTPUT CURRENT
5
5
VID = 0.2 V
TA = 25°C
4
3.5
3
VCC = 5.25 V
2.5
VCC = 5 V
2
1.5
1
VCC = 5 V
VID = 0.2 V
IOH = – 440 µA
4.5
VOH – High-Level Output Voltage – V
VOH – High-Level Output Voltage – V
4.5
VCC = 4.75 V
4
3.5
3
2.5
2
1.5
1
0.5
0.5
0
0
0
0
– 5 – 10 – 15 – 20 – 25 – 30 – 35 – 40 – 45 – 50
IOH – High-Level Output Current – mA
70
20
30 40
50
60
TA – Free-Air Temperature – °C
10
Figure 9
RECEIVER
RECEIVER
LOW-LEVEL OUTPUT VOLTAGE
vs
FREE-AIR TEMPERATURE
0.5
VCC = 5 V
TA = 25°C
VOL – Low-Level Output Voltage – V
VOL– Low-Level Output Voltage - V
0.6
0.4
0.3
0.2
0.1
0
0
5
10
15
20
25
30
IOL – Low-Level Output Current – mA
VCC = 5 V
VID = – 0.2 V
IOL = 8 mA
0.4
0.3
0.2
0.1
0
0
10
20
30
40
50
Figure 12
POST OFFICE BOX 655303
60
70
TA – Free-Air Temperature – °C
Figure 11
8
90
Figure 10
LOW-LEVEL OUTPUT VOLTAGE
vs
LOW-LEVEL OUTPUT CURRENT
0.5
80
• DALLAS, TEXAS 75265
80
90
IMPORTANT NOTICE
Texas Instruments and its subsidiaries (TI) reserve the right to make changes to their products or to discontinue
any product or service without notice, and advise customers to obtain the latest version of relevant information
to verify, before placing orders, that information being relied on is current and complete. All products are sold
subject to the terms and conditions of sale supplied at the time of order acknowledgement, including those
pertaining to warranty, patent infringement, and limitation of liability.
TI warrants performance of its semiconductor products to the specifications applicable at the time of sale in
accordance with TI’s standard warranty. Testing and other quality control techniques are utilized to the extent
TI deems necessary to support this warranty. Specific testing of all parameters of each device is not necessarily
performed, except those mandated by government requirements.
CERTAIN APPLICATIONS USING SEMICONDUCTOR PRODUCTS MAY INVOLVE POTENTIAL RISKS OF
DEATH, PERSONAL INJURY, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE (“CRITICAL
APPLICATIONS”). TI SEMICONDUCTOR PRODUCTS ARE NOT DESIGNED, AUTHORIZED, OR
WARRANTED TO BE SUITABLE FOR USE IN LIFE-SUPPORT DEVICES OR SYSTEMS OR OTHER
CRITICAL APPLICATIONS. INCLUSION OF TI PRODUCTS IN SUCH APPLICATIONS IS UNDERSTOOD TO
BE FULLY AT THE CUSTOMER’S RISK.
In order to minimize risks associated with the customer’s applications, adequate design and operating
safeguards must be provided by the customer to minimize inherent or procedural hazards.
TI assumes no liability for applications assistance or customer product design. TI does not warrant or represent
that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other
intellectual property right of TI covering or relating to any combination, machine, or process in which such
semiconductor products or services might be or are used. TI’s publication of information regarding any third
party’s products or services does not constitute TI’s approval, warranty or endorsement thereof.
Copyright  1998, Texas Instruments Incorporated