TI UC3526N

UC1526
UC2526
UC3526
Regulating Pulse Width Modulator
FEATURES
DESCRIPTION
•
8 To 35V Operation
•
5V Reference Trimmed To ±1%
•
1Hz To 400kHz Oscillator Range
•
Dual 100mA Source/Sink Outputs
•
Digital Current Limiting
•
Double Pulse Suppression
•
Programmable Deadtime
•
Under-Voltage Lockout
•
Single Pulse Metering
•
Programmable Soft-Start
•
Wide Current Limit Common Mode Range
•
TTL/CMOS Compatible Logic Ports
The UC1526 is a high performance monolithic pulse width modulator
circuit designed for fixed-frequency switching regulators and other
power control applications. Included in an 18-pin dual-in-line package are a temperature compensated voltage reference, sawtooth oscillator, error amplifier, pulse width modulator, pulse metering and
setting logic, and two low impedance power drivers. Also included
are protective features such as soft-start and under-voltage lockout,
digital current limiting, double pulse inhibit, a data latch for single
pulse metering, adjustable deadtime, and provision for symmetry correction inputs. For ease of interface, all digital control ports are TTL
and B-series CMOS compatible. Active LOW logic design allows
wired-OR connections for maximum flexibility. This versatile device
can be used to implement single-ended or push-pull switching regulators of either polarity, both transformerless and transformer coupled. The UC1526 is characterized for operation over the full military
temperature range of -55°C to +125°C. The UC2526 is characterized
for operation from -25°C to +85°C, and the UC3526 is characterized
for operation from 0° to +70°C.
•
Symmetry Correction Capability
•
Guaranteed 6 Unit Synchronization
BLOCK DIAGRAM
6/93
UC1526
UC2526
UC3526
ABSOLUTE MAXIMUM RATINGS (Note 1, 2)
RECOMMENDED OPERATING CONDITIONS (Note 3)
Input Voltage (+VIN) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +40V
Collector Supply Voltage (+VC) . . . . . . . . . . . . . . . . . . . . . +40V
Logic Inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to +5.5V
Analog Inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to +VIN
Source/Sink Load Current (each output) . . . . . . . . . . . . . 200mA
Reference Load Current . . . . . . . . . . . . . . . . . . . . . . . . . . . 50mA
Logic Sink Current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15mA
Power Dissipation at TA = +25°C (Note 2) . . . . . . . . . . 1000mW
Power Dissipation at TC = +25°C (Note 2) . . . . . . . . . . 3000mW
Operating Junction Temperature . . . . . . . . . . . . . . . . . . +150°C
Storage Temperature Range . . . . . . . . . . . . . . -65°C to +150°C
Lead Temperature (soldering, 10 seconds) . . . . . . . . . . +300°C
Note 1: Values beyond which damage may occur.
Note 2: Consult packaging section of databook for thermal
limitations and considerations of package.
Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +8V to +35V
Collector Supply Voltage . . . . . . . . . . . . . . . . . . . +4.5V to +35V
Sink/Source Load Current (each output) . . . . . . . . . 0 to 100mA
Reference Load Current . . . . . . . . . . . . . . . . . . . . . . 0 to 20mA
Oscillator Frequency Range . . . . . . . . . . . . . . . . 1Hz to 400kHz
Oscillator Timing Resistor . . . . . . . . . . . . . . . . . . . 2kΩ to 150kΩ
Oscillator Timing Capacitor . . . . . . . . . . . . . . . . . . . 1nF to 20µF
Available Deadtime Range at 40kHz . . . . . . . . . . . . . 3% to 50%
Operating Ambient Temperature Range
UC1526 . . . . . . . . . . . . . . . . . . . . . . . . . . . . -55°C to +125°C
UC2526 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -25°C to +85°C
UC3526 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0°C to +70°C
Note 3: Range over which the device is functional and
parameter limits are guaranteed.
CONNECTION DIAGRAMS
DIL-18, SOIC-18 (TOP VIEW)
J or N Package, DW Package
PACKAGE PIN FUNCTION
FUNCTION
PIN
PLCC-20, LCC-20
(TOP VIEW)
Q and L Packages
N/C
+Error
-Error
Comp.
CSS _
_____
Reset
- Current Sense
+ Current Sense
_________
Shutdown
RTIMING
CT
RD
Sync
Output A
VC
N/C
Ground
Output B
+VIN
VREF
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
ELECTRICAL CHARACTERISTICS: +VIN = 15V, and over operating ambient temperature, unless otherwise
specified, TA = TJ.
PARAMETER
TEST CONDITIONS
UC1526 / UC2526
UC3526
UNITS
MIN
TYP
MAX
MIN
TYP
MAX
4.95
5.00
5.05
4.90
5.00
5.10
V
10
20
10
30
mV
Reference Section (Note 4)
Output Voltage
TJ = + 25°C
Line Regulation
+VIN = 8 to 35V
Load Regulation
IL = 0 to 20mA
10
30
10
50
mV
Temperature Stability
Over Operating TJ
15
50
15
50
mV
Total Output
Voltage Range
Over Recommended
Operating Conditions
4.90
5.00
5.10
4.85
5.00
5.15
V
Short Circuit Current
VREF = 0V
25
50
100
25
50
100
mA
0.2
0.4
0.2
0.4
V
Under
-Voltage Lockout
_______
RESET Output Voltage
VREF = 3.8V
VREF = 4.8V
2.4
Note 4: IL = 0mA.
2
4.8
2.4
4.8
V
UC1526
UC2526
UC3526
ELECTRICAL CHARACTERISTICS: +VIN = 15V, and over operating ambient temperature, unless otherwise
specified, TA = TJ.
PARAMETER
TEST CONDITIONS
UC1526 / UC2526
MIN
TYP
MAX
UC3526
MIN
UNITS
TYP
MAX
Oscillator Section (Note 5)
Initial Accuracy
TJ = + 25°C
±3
±8
±3
±8
%
Voltage Stability
+VIN = 8 to 35V
0.5
1
0.5
1
%
Temperature Stability
Over Operating TJ
7
10
3
Minimum Frequency
RT = 150kΩ
Ω, CT = 20µ
µF
Maximum Frequency
RT = 2kΩ
Ω, CT = 1.0nF
Sawtooth Peak Voltage
+VIN = 35V
Sawtooth Valley Voltage
+VIN = 8V
1
400
%
Hz
400
3.0
0.5
5
1
3.5
1.0
kHz
3.0
0.5
3.5
1.0
V
V
Error Amplifier Section (Note 6)
Input Offset Voltage
RS ≤ 2kΩ
Ω
Input Bias Current
Input Offset Current
2
5
2
10
mV
-350
-1000
-350
-2000
nA
35
100
35
200
nA
DC Open Loop Gain
RL ≥ 10MΩ
Ω
64
72
60
72
dB
HIGH Output Voltage
VPIN1-VPIN2 ≥ 150mV, ISOURCE =
100µ
µA
3.6
4.2
3.6
4.2
V
LOW Output Voltage
µA
VPIN2-VPIN1 ≥ 150mV, ISINK = 100µ
Common Mode Rejection
Rs ≤ 12kΩ
70
94
70
94
dB
Supply Voltage Rejection
+VIN = 12 to 18V
66
80
66
80
dB
0.2
0.4
0.2
0.4
V
PWM Comparator (Note 5)
Minimum Duty Cycle
VCOMPENSATION = +0.4V
Maximum Duty Cycle
VCOMPENSATION = +3.6V
0
45
49
2.4
4.0
0
45
49
2.4
4.0
%
%
Digital Ports (SYNC, SHUTDOWN, and RESET)
HIGH Output Voltage
ISOURCE =40µ
µA
LOW Output Voltage
ISINK = 3.6mA
HIGH Input Current
VIH = +2.4V
-125
-200
LOW Input Current
VIL = +0.4V
-225
-360
100
110
-3
-10
0.2
0.4
0.2
V
0.4
V
-125
-200
µA
-225
-360
µA
100
120
mV
-3
-10
µA
Current LImit Comparator (Note 7)
Sense Voltage
RS ≤ 50Ω
Ω
90
Input Bias Current
80
Soft-Start Section
Error Clamp Voltage
RESET = +0.4V
Cs Charging Current
RESET =+2.4V
0.1
0.4
50
100
150
ISOURCE = 20mA
12.5
13.5
ISOURCE = 100mA
12
0.1
0.4
V
50
100
150
µA
12.5
13.5
Output Drivers (Each Output) (Note 8)
HIGH Output Voltage
LOW Output Voltage
13
ISINK = 20mA
0.2
ISINK = 100mA
VC = 40V
Rise Time
Fall Time
____________
SHUTDOWN = +0.4V
Collector Leakage
Power Consumption (Note 9)
Standby Current
12
V
13
V
0.3
0.2
1.2
2.0
1.2
2.0
V
50
150
50
150
µA
CL = 1000pF
0.3
0.6
0.3
0.6
µs
CL = 1000pF
0.1
0.2
0.1
0.2
µs
18
30
18
30
mA
Note 4: IL = 0mA.
Note 5: FOSC = 40kHz (RT = 4.12kΩ ± 1%, CT = 0.1µF ± 1%,
RD = 0Ω)
Note 6: VCM = 0 to +5.2V
Note 8: VC = +15V
Note 9: +VIN = +35V, RT = 4.12kΩ
3
0.3
V
UC1526
UC2526
UC3526
APPLICATIONS INFORMATION
Voltage Reference
The reference regulator of the UC1526 is based on a temperature compensated zener diode. The circuitry is fully
active at supply voltages above +8V, and provides up to
20mA of load current to external circuitry at +5.0V. In systems where additional current is required, an external
PNP transistor can be used to boost the available current.
A rugged low frequency audio-type transistor should be
used, and lead lengths between the PWM and transistor
should be as short as possible to minimize the risk of oscillations. Even so, some types of transistors may require
collector-base capacitance for stability. Up to 1 amp of
load current can be obtained with excellent regulation if
the device selected maintains high current gain.
Figure 2. Under-Voltage Lockout Schematic
Soft-Start Circuit
The soft-start circuit protects the power transistors and
rectifier diodes from high current surges during power
supply turn-on. When supply voltage is first applied
to the
_______
UC1526, the under-voltage lockout circuit holds RESET
LOW with Q3. Q1 is turned on, which holds the soft-start
capacitor voltage at zero. The second collector of Q1
clamps the output of the error amplifier to ground, guaranteeing zero duty cycle at the driver outputs. When
the
_______
supply voltage reaches normal operating range, RESET
will go HIGH. Q1 turns off, allowing the internal 100mA
current source to charge CS. Q2 clamps the error amplifier output to 1VBE above the voltage on CS. As the softstart voltage ramps up to +5V, the duty cycle of the PWM
linearly increases to whatever value the voltage regulation loop requires for an error null.
Figure 1. Extending Reference Output Current
Under-Voltage Lockout
The under-voltage lockout circuit protects the UC1526
and the power devices it controls from inadequate supply
voltage, If +VIN is too low,
the circuit disables the output
_______
drivers and holds the RESET pin LOW. This prevents
spurious output pulses while the control circuitry is stabilizing, and holds the soft-start timing capacitor in a discharged state.
The circuit consists of a +1.2V bandgap reference and
comparator circuit which is active when the reference
voltage has risen to 3VBE or +1.8V at 25°C. When the reference voltage rises to approximately +4.4V,
the circuit
_______
enables the output drivers and releases the RESET pin,
allowing a normal soft-start. The comparator has 200mV
of hysteresis to minimize oscillation at the trip point.
When +VIN to the PWM is removed and the reference
_______
drops to +4.2V, the under-voltage circuit pulls RESET
LOW again. The soft-start capacitor is immediately discharged, and the PWM is ready for another soft-start cycle.
Figure 3. Soft-Start Circuit Schematic
Digital Control Ports
The three digital control ports of the UC1526 are bi-directional. Each pin can drive TTL and 5V CMOS logic directly, up to a fan-out of 10 low-power Schottky gates.
Each pin can also be directly driven by open-collector
The UC1526 can operate from a +5V supply by connecting the VREF pin to the +VIN pin and maintaining the supply between +4.8 and +5.2V.
4
UC1526
UC2526
UC3526
APPLICATIONS INFORMATION (cont.)
TTL, open-drain CMOS, and open-collector voltage comparators; fan-in is equivalent to 1 low-power Schottky
gate. Each port is normally HIGH; the pin_____
is pulled
LOW
_
to activate the particular function. Driving SYNC LOW initiates
a discharge cycle in the oscillator. Pulling
____________
SHUTDOWN LOW
immediately inhibits all PWM output
_______
pulses. Holding RESET LOW discharges the soft-start
capacitor. The logic threshold is +1.1V at +25°C. Noise
immunity can be gained at the expense of fan-out with an
external 2k pull-up resistor to +5V.
Multiple devices can be synchronized together by programming one master unit for the desired frequency and
then sharing its sawtooth and clock waveforms with the
slave units. All CT terminals
______ are connected to the CT pin
of the master, _____
and _all SYNC terminals are likewise connected to the SYNC pin of the master. Slave RT terminals are left open or connected to VREF. Slave RD
terminals may be either left open or grounded.
Error Amplifier
The error amplifier is a transconductance design, with an
output impedance of 2MΩ . Since all voltage gain takes
place at the output pin, the open-loop gain/frequency
characteristics can be controlled with shunt reactance to
ground. When compensated for unity-gain stability with
100pF, the amplifier has an open-loop pole at 800Hz.
The input connections to the error amplifier are determined by the polarity of the switching supply output voltage. For positive supplies, the common-mode voltage is
+5.0V and the feedback connections in Figure 6A are
used. With negative supplies, the common-mode voltage
is ground and the feedback divider is connected between
the negative output and the +5.0V reference voltage, as
shown in Figure 6B.
Figure 4. Digital Control Port Schematic
Oscillator
The oscillator is programmed for frequency and dead time
with three components: RT, CT and RD. Two waveforms
are generated: a sawtooth waveform at pin 10 for pulse
width modulation, and a logic clock at pin 12. The following procedure is recommended for choosing timing values:
Output Drivers
The totem-pole output drivers of the UC1526 are designed to source and sink 100mA continuously and
200mA peak. Loads can be driven either from the output
pins 13 and 16, or from the +VC, as required.
Since the bottom transistor of the totem-pole is allowed to
saturate, there is a momentary conduction path from the
+VC terminal to ground during switching. To limit the resulting current spikes a small resistor in series with pin 14
is always recommended. The resistor value is determined by the driver supply voltage, and should be chosen
for 200mA peak currents.
1. With RD = 0 (pin 11 shorted to ground) select values
for RT and CT from Figure 7 to give the desired oscillator
period. Remember that the frequency at each driver output is half the oscillator frequency, and the frequency at
the +VC terminal is the same as the oscillator frequency.
2. If more dead time is required, select a large value of
RD. At 40kHz dead time increases by 400ns/Ω .
3. Increasing the dead time will cause the oscillator frequency to decrease slightly. Go back and decrease the
value of RT slightly to bring the frequency back to the
nominal design value.
The UC1526 can be synchronized to an external logic
clock by programming the oscillator to free-run at a frequency 10% slower than the sync frequency. A periodic
______
LOW logic pulse approximately 0.5µs wide at the SYNC
pin will then lock the oscillator to the external frequency.
Figure 5. Oscillator Connections and Waveforms
5
UC1526
UC2526
UC3526
Figure 6. Error Amplifier Connections
Figure 8. Single-Ended Configuration
Figure 7. Push-Pull Configuration
Figure 9. Driving N-channel Power Mosfets
TYPICAL CHARACTERISTICS
Oscillator Period vs RT and CT
Oscillation Period
6
UC1526
UC2526
UC3526
TYPICAL CHARACTERISTICS
Output Driver Deadtime vs RD Value
Under Voltage Lockout Characteristic
Error Amplifier Open Loop Gain vs Frequency
Current Limit Transfer Function
Shutdown Delay
Output Driver Saturation Voltage
UNITRODE INTEGRATED CIRCUITS
7 CONTINENTAL BLVD. • MERRIMACK, NH 03054
TEL. (603) 424-2410 • FAX (603) 424-3460
7
PACKAGE OPTION ADDENDUM
www.ti.com
27-Sep-2005
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.
Addendum-Page 2
PACKAGE OPTION ADDENDUM
www.ti.com
9-Oct-2007
PACKAGING INFORMATION
Orderable Device
Status (1)
Package
Type
Package
Drawing
Pins Package Eco Plan (2)
Qty
Lead/Ball Finish
MSL Peak Temp (3)
85515012A
ACTIVE
LCCC
FK
20
1
TBD
8551501VA
ACTIVE
CDIP
J
18
1
TBD
POST-PLATE N / A for Pkg Type
A42 SNPB
N / A for Pkg Type
UC1526J
ACTIVE
CDIP
J
18
1
TBD
A42 SNPB
N / A for Pkg Type
UC1526J883B
ACTIVE
CDIP
J
18
1
TBD
A42 SNPB
N / A for Pkg Type
UC1526L
ACTIVE
LCCC
FK
20
1
TBD
POST-PLATE N / A for Pkg Type
UC1526L883B
ACTIVE
LCCC
FK
20
1
TBD
POST-PLATE N / A for Pkg Type
UC2526AJ
ACTIVE
CDIP
J
18
1
TBD
A42 SNPB
N / A for Pkg Type
UC2526N
ACTIVE
PDIP
N
18
20
Green (RoHS &
no Sb/Br)
CU NIPDAU
N / A for Pkg Type
UC2526NG4
ACTIVE
PDIP
N
18
20
Green (RoHS &
no Sb/Br)
CU NIPDAU
N / A for Pkg Type
UC3526AJ
ACTIVE
CDIP
J
18
1
TBD
A42 SNPB
N / A for Pkg Type
UC3526DW
ACTIVE
SOIC
DW
18
40
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
UC3526DWG4
ACTIVE
SOIC
DW
18
40
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
UC3526DWTR
ACTIVE
SOIC
DW
18
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
UC3526DWTRG4
ACTIVE
SOIC
DW
18
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
UC3526N
ACTIVE
PDIP
N
18
20
Green (RoHS &
no Sb/Br)
CU NIPDAU
N / A for Pkg Type
UC3526NG4
ACTIVE
PDIP
N
18
20
Green (RoHS &
no Sb/Br)
CU NIPDAU
N / A for Pkg Type
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check
http://www.ti.com/productcontent for the latest availability information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and
package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS
compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame
retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder
temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
9-Oct-2007
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
5-Oct-2007
TAPE AND REEL BOX INFORMATION
Device
UC3526DWTR
Package Pins
DW
18
Site
Reel
Diameter
(mm)
Reel
Width
(mm)
A0 (mm)
B0 (mm)
K0 (mm)
P1
(mm)
SITE 41
330
24
10.9
12.0
2.7
12
Pack Materials-Page 1
W
Pin1
(mm) Quadrant
24
Q1
PACKAGE MATERIALS INFORMATION
www.ti.com
5-Oct-2007
Device
Package
Pins
Site
Length (mm)
Width (mm)
Height (mm)
UC3526DWTR
DW
18
SITE 41
346.0
346.0
41.0
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements,
improvements, and other changes to its products and services at any time and to discontinue any product or service without notice.
Customers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s
standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this
warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily
performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should
provide adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask
work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services
are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such
products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under
the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is
accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an
unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties
may be subject to additional restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service
voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business
practice. TI is not responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would
reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement
specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications
of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related
requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any
applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its
representatives against any damages arising out of the use of TI products in such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is
solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in
connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products
are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any
non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Applications
Amplifiers
amplifier.ti.com
Audio
www.ti.com/audio
Data Converters
dataconverter.ti.com
Automotive
www.ti.com/automotive
DSP
dsp.ti.com
Broadband
www.ti.com/broadband
Interface
interface.ti.com
Digital Control
www.ti.com/digitalcontrol
Logic
logic.ti.com
Military
www.ti.com/military
Power Mgmt
power.ti.com
Optical Networking
www.ti.com/opticalnetwork
Microcontrollers
microcontroller.ti.com
Security
www.ti.com/security
RFID
www.ti-rfid.com
Telephony
www.ti.com/telephony
Low Power
Wireless
www.ti.com/lpw
Video & Imaging
www.ti.com/video
Wireless
www.ti.com/wireless
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2007, Texas Instruments Incorporated