TI TLC272IP

TLC272, TLC272A, TLC272B, TLC272Y, TLC277
LinCMOS PRECISION DUAL OPERATIONAL AMPLIFIERS
SLOS091B – OCTOBER 1987 – REVISED AUGUST 1994
D
D
D
D
D
D
D
D
D
D, JG, P, OR PW PACKAGE
(TOP VIEW)
1OUT
1IN –
1IN +
GND
1
8
2
7
3
6
4
5
VDD
2OUT
2IN –
2IN +
FK PACKAGE
(TOP VIEW)
NC
1OUT
NC
VDD
NC
D
Trimmed Offset Voltage:
TLC277 . . . 500 µV Max at 25°C,
VDD = 5 V
Input Offset Voltage Drift . . . Typically
0.1 µV/Month, Including the First 30 Days
Wide Range of Supply Voltages Over
Specified Temperature Range:
0°C to 70°C . . . 3 V to 16 V
– 40°C to 85°C . . . 4 V to 16 V
– 55°C to 125°C . . . 4 V to 16 V
Single-Supply Operation
Common-Mode Input Voltage Range
Extends Below the Negative Rail (C-Suffix,
I-Suffix types)
Low Noise . . . Typically 25 nV/√Hz at
f = 1 kHz
Output Voltage Range Includes Negative
Rail
High Input impedance . . . 1012 Ω Typ
ESD-Protection Circuitry
Small-Outline Package Option Also
Available in Tape and Reel
Designed-in Latch-Up Immunity
NC
1IN –
NC
1IN +
NC
4
3 2 1 20 19
18
5
17
6
16
7
15
8
14
9 10 11 12 13
NC
2OUT
NC
2IN –
NC
NC
GND
NC
2IN +
NC
D
NC – No internal connection
DISTRIBUTION OF TLC277
INPUT OFFSET VOLTAGE
30
description
These devices use Texas instruments silicon-gate
LinCMOS technology, which provides offset
voltage stability far exceeding the stability
available with conventional metal-gate processes.
25
Percentage of Units – %
The TLC272 and TLC277 precision dual
operational amplifiers combine a wide range of
input offset voltage grades with low offset voltage
drift, high input impedance, low noise, and speeds
approaching that of general-purpose BiFET
devices.
473 Units Tested From 2 Wafer Lots
VDD = 5 V
TA = 25°C
P Package
20
15
10
5
The extremely high input impedance, low bias
currents, and high slew rates make these cost0
effective devices ideal for applications which have
– 800
– 400
0
400
800
previously been reserved for BiFET and NFET
VIO – Input Offset Voltage – µV
products. Four offset voltage grades are available
(C-suffix and I-suffix types), ranging from the
low-cost TLC272 (10 mV) to the high-precision TLC277 (500 µV). These advantages, in combination with good
common-mode rejection and supply voltage rejection, make these devices a good choice for new
state-of-the-art designs as well as for upgrading existing designs.
LinCMOS is a trademark of Texas Instruments Incorporated.
Copyright  1994, Texas Instruments Incorporated
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of Texas Instruments
standard warranty. Production processing does not necessarily include
testing of all parameters.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
1
TLC272, TLC272A, TLC272B, TLC272Y, TLC277
LinCMOS PRECISION DUAL OPERATIONAL AMPLIFIERS
SLOS091B – OCTOBER 1987 – REVISED AUGUST 1994
AVAILABLE OPTIONS
PACKAGED DEVICES
TA
VIOmax
AT 25°C
SMALL
OUTLINE
(D)
CHIP
CARRIER
(FK)
CERAMIC
DIP
(JG)
PLASTIC
DIP
(P)
TSSOP
(PW)
CHIP
FORM
(Y)
0°C to 70°c
500 µV
2 mV
5 mV
10mV
TLC277CD
TLC272BCD
TLC272ACD
TLC272CD
—
—
—
—
—
—
—
—
TLC277CP
TLC272BCP
TLC272ACP
TLC272CP
—
—
—
TLC272CPW
—
—
—
TLC272Y
– 40°C to 85°C
500 µV
2 mV
5 mV
10 mV
TLC277ID
TLC272BID
TLC272AID
TLC272ID
—
—
—
—
—
—
—
—
TLC277IP
TLC272BIP
TLC272AIP
TLC272IP
—
—
—
—
—
—
—
—
– 55°C to 125°C
500 µV
µ
10 mV
TLC277MD
TLC272MD
TLC277MFK
TLC272MFK
TLC277MJG
TLC272MJG
TLC277MP
TLC272MP
—
—
—
—
The D package is available taped and reeled. Add R suffix to the device type (e.g., TLC277CDR).
description (continued)
In general, many features associated with bipolar technology are available on LinCMOS operational amplifiers
without the power penalties of bipolar technology. General applications such as transducer interfacing, analog
calculations, amplifier blocks, active filters, and signal buffering are easily designed with the TLC272 and
TLC277. The devices also exhibit low voltage single-supply operation, making them ideally suited for remote
and inaccessible battery-powered applications. The common-mode input voltage range includes the negative
rail.
A wide range of packaging options is available, including small-outline and chip carrier versions for high-density
system applications.
The device inputs and outputs are designed to withstand –100-mA surge currents without sustaining latch-up.
The TLC272 and TLC277 incorporate internal ESD-protection circuits that prevent functional failures at voltages
up to 2000 V as tested under MIL-STD-883C, Method 3015.2; however, care should be exercised in handling
these devices as exposure to ESD may result in the degradation of the device parametric performance.
The C-suffix devices are characterized for operation from 0°C to 70°C. The I-suffix devices are characterized
for operation from – 40°C to 85°C. The M-suffix devices are characterized for operation over the full military
temperature range of – 55°C to 125°C.
2
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
TLC272, TLC272A, TLC272B, TLC272Y, TLC277
LinCMOS PRECISION DUAL OPERATIONAL AMPLIFIERS
SLOS091B – OCTOBER 1987 – REVISED AUGUST 1994
equivalent schematic (each amplifier)
VDD
P3
P4
R6
R1
N5
R2
IN –
P5
P1
P6
P2
IN +
R5
C1
OUT
N3
N1
R3
N2
D1
N4
R4
N6
N7
R7
D2
GND
TLC272Y chip information
This chip, when properly assembled, displays characteristics similar to the TLC272C. Thermal compression or
ultrasonic bonding may be used on the doped-aluminum bonding pads. Chips may be mounted with conductive
epoxy or a gold-silicon preform.
BONDING PAD ASSIGNMENTS
1IN +
(3)
(2)
1IN –
2OUT
VDD
(8)
+
(1)
+
(7)
–
60
1OUT
–
(5)
(6)
2IN +
2IN –
(4)
GND
CHIP THICKNESS: 15 TYPICAL
BONDING PADS: 4 × 4 MINIMUM
TJmax = 150°C
TOLERANCES ARE ± 10%.
ALL DIMENSIONS ARE IN MILS.
73
POST OFFICE BOX 655303
PIN (4) IS INTERNALLY CONNECTED
TO BACKSIDE OF CHIP.
• DALLAS, TEXAS 75265
3
TLC272, TLC272A, TLC272B, TLC272Y, TLC277
LinCMOS PRECISION DUAL OPERATIONAL AMPLIFIERS
SLOS091B – OCTOBER 1987 – REVISED AUGUST 1994
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)†
Supply voltage, VDD (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 V
Differential input voltage, VID (see Note 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ± VDD
Input voltage range, VI (any input) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 0.3 V to VDD
Input current, II . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ± 5 mA
output current, IO (each output) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ± 30 mA
Total current into VDD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 mA
Total current out of GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 mA
Duration of short-circuit current at (or below) 25°C (see Note 3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . unlimited
Continuous total dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See Dissipation Rating Table
Operating free-air temperature, TA: C suffix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0°C to 70°C
I suffix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 40°C to 85°C
M suffix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 55°C to 125°C
Storage temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 65°C to 150°C
Case temperature for 60 seconds: FK package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 260°C
Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds: D, P, or PW package . . . . . . . . . . . . 260°C
Lead temperature 1,6 mm (1/16 inch) from case for 60 seconds: JG package . . . . . . . . . . . . . . . . . . . . 300°C
† Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
NOTES: 1. All voltage values, except differential voltages, are with respect to network ground.
2. Differential voltages are at IN+ with respect to IN –.
3. The output may be shorted to either supply. Temperature and/or supply voltages must be limited to ensure that the maximum
dissipation rating is not exceeded (see application section).
DISSIPATION RATING TABLE
PACKAGE
TA ≤ 25°C
POWER RATING
DERATING FACTOR
ABOVE TA = 25°C
TA = 70°C
POWER RATING
TA = 85°C
POWER RATING
TA = 125°C
POWER RATING
D
725 mW
5.8 mW/°C
464 mW
377 mW
N/A
FK
1375 mW
11 mW/°C
880 mW
715 mW
275 mW
JG
1050 mW
8.4 mW/°C
672 mW
546 mW
210 mW
P
1000 mW
8.0 mW/°C
640 mW
520 mW
N/A
PW
525 mW
4.2 mW/°C
336 mW
N/A
N/A
recommended operating conditions
Supply voltage, VDD
Common mode input voltage,
Common-mode
voltage VIC
VDD = 5 V
VDD = 10 V
Operating free-air temperature, TA
4
POST OFFICE BOX 655303
C SUFFIX
I SUFFIX
M SUFFIX
MIN
MAX
MIN
MAX
MIN
MAX
3
16
4
16
4
16
– 0.2
3.5
– 0.2
3.5
0
3.5
– 0.2
8.5
– 0.2
8.5
0
8.5
0
70
– 40
85
– 55
125
• DALLAS, TEXAS 75265
UNIT
V
V
°C
TLC272, TLC272A, TLC272B, TLC272Y, TLC277
LinCMOS PRECISION DUAL OPERATIONAL AMPLIFIERS
SLOS091B – OCTOBER 1987 – REVISED AUGUST 1994
electrical characteristics at specified free-air temperature, VDD = 5 V (unless otherwise noted)
PARAMETER
TEST CONDITIONS
TA†
TLC272C, TLC272AC,
TLC272BC, TLC277C
MIN
VIO
TLC272C
VO = 1.4 V,,
RS = 50 Ω,
VIC = 0,,
RL = 10 kΩ
TLC272AC
VO = 1.4 V,,
RS = 50 Ω,
VIC = 0,,
RL = 10 kΩ
Input offset voltage
TLC272BC
TLC277C
VO = 1.4 V,,
RS = 50 Ω,
VIC = 0,,
RL = 10 kΩ
VO = 1.4 V,,
RS = 50 Ω,
VIC = 0,,
RL = 10 kΩ
αVIO
Temperature coefficient of input offset voltage
IIO
Input offset current (see Note 4)
VO = 2
2.5
5V
V,
VIC = 2
2.5
5V
IIB
Input bias current (see Note 4)
VO = 2
2.5
5V
V,
VIC = 2
2.5
5V
VICR
VOH
VOL
AVD
CMRR
kSVR
IDD
25°C
VID = 100 mV,
Low-level output voltage
VID = –100 mV,
Large-signal differential voltage amplification
Common-mode rejection ratio
VO = 0.25 V to 2 V,
RL = 10 kΩ
IOL = 0
RL = 10 kΩ
VIC = VICRmin
Supply-voltage
S
l
lt
rejection
j ti ratio
ti
(∆VDD /∆VIO)
VDD = 5 V to 10 V,
Supply current (two amplifiers)
VO = 2.5
2 5 V,
V
No load
VO = 1.4 V
VIC = 5 V
V,
MAX
1.1
10
Full range
12
25°C
0.9
5
230
2000
Full range
UNIT
mV
6.5
25°C
Full range
3000
25°C
200
Full range
500
µV
1500
25°C to
70°C
1.8
25°C
0.1
70°C
7
25°C
0.6
70°C
40
25°C
– 0.2
to
4
Full range
– 0.2
to
3.5
Common-mode input voltage
g range
g
(see Note 5)
High-level output voltage
TYP
µV/°C
300
600
– 0.3
to
4.2
pA
pA
V
V
25°C
3.2
3.8
0°C
3
3.8
70°C
3
3.8
V
25°C
0
50
0°C
0
50
70°C
0
50
25°C
5
23
0°C
4
27
70°C
4
20
25°C
65
80
0°C
60
84
70°C
60
85
25°C
65
95
0°C
60
94
70°C
60
96
mV
V/mV
dB
dB
25°C
1.4
3.2
0°C
1.6
3.6
70°C
1.2
2.6
mA
† Full range is 0°C to 70°C.
NOTES: 4. The typical values of input bias current and input offset current below 5 pA were determined mathematically.
5. This range also applies to each input individually.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
5
TLC272, TLC272A, TLC272B, TLC272Y, TLC277
LinCMOS PRECISION DUAL OPERATIONAL AMPLIFIERS
SLOS091B – OCTOBER 1987 – REVISED AUGUST 1994
electrical characteristics at specified free-air temperature, VDD = 10 V (unless otherwise noted)
PARAMETER
TEST CONDITIONS
TA†
TLC272C, TLC272AC,
TLC272BC, TLC277C
MIN
VIO
TLC272C
VO = 1.4 V,,
RS = 50 Ω,
VIC = 0,,
RL = 10 kΩ
TLC272AC
VO = 1.4 V,,
RS = 50 Ω,
VIC = 0,,
RL = 10 kΩ
Input offset voltage
TLC272BC
TLC277C
VO = 1.4 V,,
RS = 50 Ω,
VO = 1.4 V,,
RS = 50 Ω,
VIC = 0,,
RL = 10 kΩ
VIC = 0,,
RL = 10 kΩ
Temperature coefficient of input offset voltage
IIO
Input offset current (see Note 4)
VO = 5 V,
V
VIC = 5 V
IIB
Input bias current (see Note 4)
VO = 5 V,
V
VIC = 5 V
VOH
VOL
AVD
CMRR
kSVR
IDD
VID = 100 mV,
Low-level output voltage
VID = –100 mV,
Large-signal differential voltage amplification
Common-mode rejection ratio
VO = 1 V to 6 V,
RL = 10 kΩ
IOL = 0
RL = 10 kΩ
VIC = VICRmin
Supply-voltage
S
l
lt
rejection
j ti ratio
ti
(∆VDD /∆VIO)
VDD = 5 V to 10 V,
Supply current (two amplifiers)
VO = 2.5
25V
V,
No load
VO = 1.4 V
VIC = 5 V
V,
1.1
10
12
25°C
0.9
5
290
2000
Full range
Full range
3000
25°C
250
Full range
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
mV
800
µV
1900
µV/°C
2
25°C
0.1
70°C
7
25°C
0.7
70°C
50
25°C
– 0.2
to
9
Full range
– 0.2
to
8.5
300
600
– 0.3
to
9.2
pA
pA
V
V
25°C
8
8.5
0°C
7.8
8.5
70°C
7.8
8.4
V
25°C
0
50
0°C
0
50
70°C
0
50
25°C
10
36
0°C
7.5
42
70°C
7.5
32
25°C
65
85
0°C
60
88
70°C
60
88
25°C
65
95
0°C
60
94
70°C
60
96
mV
V/mV
dB
dB
25°C
1.9
4
0°C
2.3
4.4
70°C
1.6
3.4
† Full range is 0°C to 70°C.
NOTES: 4. The typical values of input bias current and input offset current below 5 pA were determined mathematically.
5. This range also applies to each input individually.
6
UNIT
6.5
25°C
Common-mode input voltage
g range
g
(see Note 5)
High-level output voltage
MAX
Full range
25°C to
70°C
αVIO
VICR
25°C
TYP
mA
TLC272, TLC272A, TLC272B, TLC272Y, TLC277
LinCMOS PRECISION DUAL OPERATIONAL AMPLIFIERS
SLOS091B – OCTOBER 1987 – REVISED AUGUST 1994
electrical characteristics at specified free-air temperature, VDD = 5 V (unless otherwise noted)
PARAMETER
TEST CONDITIONS
TA†
TLC272I, TLC272AI,
TLC272BI, TLC277I
MIN
VIO
TLC272I
VO = 1.4 V,,
RS = 50 Ω,
VIC = 0,,
RL = 10 kΩ
TLC272AI
VO = 1.4 V,,
RS = 50 Ω,
VIC = 0,,
RL = 10 kΩ
Input offset voltage
TLC272BI
TLC277I
VO = 1.4 V,,
RS = 50 Ω,
VIC = 0,,
RL = 10 kΩ
VO = 1.4 V,,
RS = 50 Ω,
VIC = 0,,
RL = 10 kΩ
αVIO
Temperature coefficient of input offset voltage
IIO
Input offset current (see Note 4)
VO = 2
2.5
5V
V,
VIC = 2
2.5
5V
IIB
Input bias current (see Note 4)
VO = 2
2.5
5V
V,
VIC = 2
2.5
5V
25°C
VOL
AVD
CMRR
kSVR
VID = 100 mV,
Low-level output voltage
VID = –100 mV,
L
Large-signal
i
l diff
differential
ti l voltage
lt
amplification
lifi ti
Common-mode rejection ratio
S
l
lt
j ti ratio
ti
Supply-voltage
rejection
(∆VDD /∆VIO)
VO = 1 V to 6 V,
RL = 10 kΩ
IOL = 0
RL = 10 kΩ
VIC = VICRmin
VDD = 5 V to 10 V,
VO = 1.4 V
10
0.9
5
230
2000
25°C
3500
Full range
25°C
200
500
25°C to
85°C
1.8
25°C
0.1
85°C
24
25°C
0.6
85°C
200
– 0.2
to
4
15
35
– 0.3
to
4.2
– 0.2
to
3.5
25°C
3.2
3.8
– 40°C
3
3.8
85°C
3
3.8
V
25°C
0
50
– 40°C
0
50
85°C
0
50
25°C
5
23
– 40°C
3.5
32
85°C
3.5
19
25°C
65
80
– 40°C
60
81
85°C
60
86
25°C
65
95
– 40°C
60
92
85°C
60
dB
dB
96
4.4
85°C
1.1
† Full range is – 40°C to 85°C.
NOTES: 4. The typical values of input bias current and input offset current below 5 pA were determined mathematically.
5. This range also applies to each input individually.
2.4
• DALLAS, TEXAS 75265
mV
V/mV
3.2
POST OFFICE BOX 655303
pA
V
1.9
VIC = 5 V
V,
pA
V
– 40°C
VO = 5 V,
V
No load
µV
µV/°C
1.4
Supply current (two amplifiers)
mV
2000
Full range
25°C
IDD
UNIT
7
Full range
Common-mode input voltage
g range
g
(see Note 5)
High-level output voltage
1.1
13
25°C
Full range
VOH
MAX
Full range
25°C
VICR
TYP
mA
7
TLC272, TLC272A, TLC272B, TLC272Y, TLC277
LinCMOS PRECISION DUAL OPERATIONAL AMPLIFIERS
SLOS091B – OCTOBER 1987 – REVISED AUGUST 1994
electrical characteristics at specified free-air temperature, VDD = 10 V (unless otherwise noted)
PARAMETER
TEST CONDITIONS
TA†
TLC272I, TLC272AI,
TLC272BI, TLC277I
MIN
VIO
TLC272I
VO = 1.4 V,,
RS = 50 Ω,
VIC = 0,,
RL = 10 kΩ
TLC272AI
VO = 1.4 V,,
RS = 50 Ω,
VIC = 0,,
RL = 10 kΩ
Input offset voltage
TLC272BI
TLC277I
VO = 1.4 V,,
RS = 50 Ω,
VIC = 0,,
RL = 10 kΩ
VO = 1.4 V,,
RS = 50 Ω,
VIC = 0,,
RL = 10 kΩ
Temperature coefficient of input offset voltage
IIO
Input offset current (see Note 4)
VO = 5 V,
V
VIC = 5 V
IIB
Input bias current (see Note 4)
VO = 5 V,
V
VIC = 5 V
VOH
VOL
AVD
CMRR
kSVR
VID = 100 mV,
Low-level output voltage
VID = –100 mV,
Large-signal differential voltage amplification
Common-mode rejection ratio
S
l
lt
j ti ratio
ti
Supply-voltage
rejection
(∆VDD /∆VIO)
VO = 1 V to 6 V,
RL = 10 kΩ
IOL = 0
RL = 10 kΩ
VIC = VICRmin
VDD = 5 V to 10 V,
VO = 1.4 V
1.1
10
13
25°C
0.9
5
290
2000
25°C
3500
Full range
25°C
250
800
25°C
0.1
85°C
26
25°C
0.7
85°C
220
25°C
– 0.2
to
9
Full range
– 0.2
to
8.5
1000
2000
– 0.3
to
9.2
25°C
8
8.5
– 40°C
7.8
8.5
85°C
7.8
8.5
V
25°C
0
50
– 40°C
0
50
85°C
0
50
25°C
10
36
– 40°C
7
46
85°C
7
31
25°C
65
85
– 40°C
60
87
85°C
60
88
25°C
65
95
– 40°C
60
92
85°C
60
dB
dB
96
5
85°C
1.5
† Full range is – 40°C to 85°C.
NOTES: 4. The typical values of input bias current and input offset current below 5 pA were determined mathematically.
5. This range also applies to each input individually.
3.2
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
mV
V/mV
4
8
pA
V
2.8
VIC = 5 V
V,
pA
V
– 40°C
VO = 5 V,
V
No load
µV
µV/°C
2
1.4
Supply current (two amplifiers)
mV
2900
Full range
25°C
IDD
UNIT
7
Full range
Common-mode input voltage
g range
g
(see Note 5)
High-level output voltage
MAX
Full range
25°C to
85°C
αVIO
VICR
25°C
TYP
mA
TLC272, TLC272A, TLC272B, TLC272Y, TLC277
LinCMOS PRECISION DUAL OPERATIONAL AMPLIFIERS
SLOS091B – OCTOBER 1987 – REVISED AUGUST 1994
electrical characteristics at specified free-air temperature, VDD = 5 V (unless otherwise noted)
PARAMETER
VIO
TEST CONDITIONS
VO = 1.4 V,,
RS = 50 Ω,
VIC = 0,,
RL = 10 kΩ
Full range
TLC277M
VO = 1.4 V,,
RS = 50 Ω,
VIC = 0,,
RL = 10 kΩ
Full range
Input offset voltage
Temperature coefficient of input offset
voltage
IIO
Input offset current (see Note 4)
VO = 2
2.5
5V
Input bias current (see Note 4)
VIC = 2
2.5
5V
5V
VO = 2
2.5
5V
VIC = 2
2.5
VOL
AVD
CMRR
kSVR
VID = 100 mV,
Low-level output voltage
VID = – 100 mV,
Large-signal differential voltage amplification
Common-mode rejection ratio
Supply-voltage
S
l
lt
rejection
j ti ratio
ti
(∆VDD /∆VIO)
VO = 0.25 V to 2 V
RL = 10 kΩ
IOL = 0
RL = 10 kΩ
VIC = VICRmin
VDD = 5 V to 10 V,
VO = 1.4 V
MAX
1.1
10
12
200
500
3750
2.1
25°C
0.1
125°C
1.4
25°C
0.6
125°C
Common-mode input voltage
g range
g
(see Note 5)
High-level output voltage
TYP
25°C to
125°C
Full range
VOH
MIN
25°C
25°C
VICR
TLC272M, TLC277M
25°C
TLC272M
αVIO
IIB
TA†
9
0
to
4
35
– 0.3
to
4.2
0
to
3.5
V
25°C
3.2
3.8
– 55°C
3
3.8
125°C
3
3.8
V
25°C
0
50
– 55°C
0
50
125°C
0
50
25°C
5
23
– 55°C
3.5
35
125°C
3.5
16
25°C
65
80
– 55°C
60
81
125°C
60
84
25°C
65
95
– 55°C
60
90
125°C
60
dB
dB
97
5
125°C
1
† Full range is – 55°C to 125°C.
NOTES: 4. The typical values of input bias current and input offset current below 5 pA were determined mathematically.
5. This range also applies to each input individually.
2.2
• DALLAS, TEXAS 75265
mV
V/mV
3.2
POST OFFICE BOX 655303
nA
V
2
VIC = 2
2.5
5V
V,
nA
pA
– 55°C
VO = 2.5
25V
V,
No load
µV
pA
15
1.4
Supply current (two amplifiers)
mV
µV/°C
25°C
IDD
UNIT
mA
9
TLC272, TLC272A, TLC272B, TLC272Y, TLC277
LinCMOS PRECISION DUAL OPERATIONAL AMPLIFIERS
SLOS091B – OCTOBER 1987 – REVISED AUGUST 1994
electrical characteristics at specified free-air temperature, VDD = 10 V (unless otherwise noted)
PARAMETER
VIO
TEST CONDITIONS
TLC272M
VO = 1.4 V,
RS = 50 Ω,
VIC = 0,
RL = 10 kΩ
Full range
TLC277M
VO = 1.4 V,
RS = 50 Ω,
VIC = 0,
RL = 10 kΩ
Full range
Input offset voltage
αVIO
Temperature coefficient of input offset
voltage
IIO
Input offset current (see Note 4)
IIB
VICR
VOH
VOL
TA†
Input bias current (see Note 4)
VO = 5 V,
V
VIC = 5 V
V
VO = 5 V,
VIC = 5 V
Low-level output voltage
VID = 100 mV,
VID = – 100 mV,
RL = 10 kΩ
IOL = 0
MIN
25°C
CMRR
kSVR
Large-signal
L
i
l differential
diff
ti l voltage
lt
amplification
am
lification
Common-mode rejection ratio
VO = 1 V to 6 V,
RL = 10 kΩ
VIC = VICRmin
S
l
lt
j ti ratio
ti
Supply-voltage
rejection
(∆VDD /∆VIO)
VDD = 5 V to 10 V,
Supply current (two amplifiers)
VO = 5 V,
V
No load
VO = 1.4 V
IDD
1.1
10
2.2
25°C
0.1
125°C
1.8
25°C
0.7
125°C
10
25°C
0
to
9
Full range
0
to
8.5
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
UNIT
mV
µV
µV/°C
pA
15
nA
pA
35
– 0.3
to
9.2
nA
V
V
25°C
8
8.5
– 55°C
7.8
8.5
125°C
7.8
8.4
V
25°C
0
50
– 55°C
0
50
0
50
25°C
10
36
– 55°C
7
50
125°C
7
27
25°C
65
85
– 55°C
60
87
125°C
60
86
25°C
65
95
– 55°C
60
90
125°C
60
97
1.9
mV
V/mV
dB
dB
4
– 55°C
3
6
125°C
1.3
2.8
† Full range is – 55°C to 125°C.
NOTES: 4. The typical values of input bias current and input offset current below 5 pA were determined mathematically.
5. This range also applies to each input individually.
10
800
4300
25°C to
125°C
25°C
VIC = 5 V
V,
MAX
250
125°C
AVD
TYP
12
25°C
Common-mode input voltage
g range
g
(see Note 5)
High-level output voltage
TLC272M, TLC277M
mA
TLC272, TLC272A, TLC272B, TLC272Y, TLC277
LinCMOS PRECISION DUAL OPERATIONAL AMPLIFIERS
SLOS091B – OCTOBER 1987 – REVISED AUGUST 1994
electrical characteristics, VDD = 5 V, TA = 25°C (unless otherwise noted)
PARAMETER
TEST CONDITIONS
VIO
Input offset voltage
αVIO
Temperature coefficient of input offset voltage
IIO
IIB
Input offset current (see Note 4)
VICR
Common-mode input voltage range (see Note 5)
VOH
VOL
High-level output voltage
AVD
CMRR
Large-signal differential voltage amplification
kSVR
Supply-voltage rejection ratio (∆VDD /∆VIO)
IDD
Supply current (two amplifiers)
Input bias current (see Note 4)
VO = 1.4 V,,
RS = 50 Ω,
VIC = 0,,
RL = 10 kΩ
VO = 2.5 V,
VO = 2.5 V,
VIC = 2.5 V
VIC = 2.5 V
VID = 100 mV,
VID = –100 mV,
Low-level output voltage
Common-mode rejection ratio
VO = 0.25 V to 2 V
VIC = VICRmin
VDD = 5 V to 10 V,
VO = 2.5 V,
No load
TLC272Y
MIN
TYP
MAX
11
1.1
10
UNIT
mV
1.8
µV/°C
0.1
pA
0.6
pA
– 0.2
to
4
– 0.3
to
4.2
V
RL = 10 kΩ
3.2
3.8
V
IOL = 0
RL = 10 kΩ
5
23
V/mV
65
80
dB
65
95
dB
VO = 1.4 V
VIC = 2.5 V,
0
1.4
50
3.2
mV
mA
NOTES: 4. The typical values of input bias current and input offset current below 5 pA were determined mathematically.
5. This range also applies to each input individually.
electrical characteristics, VDD = 10 V, TA = 25°C (unless otherwise noted)
PARAMETER
TEST CONDITIONS
VIO
Input offset voltage
αVIO
Temperature coefficient of input offset voltage
IIO
IIB
Input offset current (see Note 4)
Input bias current (see Note 4)
VICR
Common-mode input voltage range (see Note 5)
VOH
VOL
High-level output voltage
AVD
CMRR
Large-signal differential voltage amplification
kSVR
Supply-voltage rejection ratio (∆VDD /∆VIO)
IDD
Supply current (two amplifiers)
VO = 1.4 V,,
RS = 50 Ω,
VIC = 0,,
RL = 10 kΩ
VO = 5 V,
VO = 5 V,
VIC = 5 V
VIC = 5 V
VID = 100 mV,
VID = –100 mV,
Low-level output voltage
Common-mode rejection ratio
VO = 1 V to 6 V,
VIC = VICRmin
VDD = 5 V to 10 V,
VO = 5 V,
No load
RL = 10 kΩ
IOL = 0
RL = 10 kΩ
VO = 1.4 V
VIC = 5 V,
TLC272Y
MIN
TYP
MAX
11
1.1
10
UNIT
mV
1.8
µV/°C
0.1
pA
0.7
pA
– 0.2
to
9
– 0.3
to
9.2
V
8
8.5
0
V
50
mV
10
36
V/mV
65
85
dB
65
95
dB
1.9
4
mA
NOTES: 4. The typical values of input bias current and input offset current below 5 pA were determined mathematically.
5. This range also applies to each input individually.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
11
TLC272, TLC272A, TLC272B, TLC272Y, TLC277
LinCMOS PRECISION DUAL OPERATIONAL AMPLIFIERS
SLOS091B – OCTOBER 1987 – REVISED AUGUST 1994
operating characteristics at specified free-air temperature, VDD = 5 V
PARAMETER
TEST CONDITIONS
TA
TLC272C, TLC272AC,
TLC272BC, TLC277C
MIN
VIPP = 1 V
SR
Slew rate at unity gain
RL = 10 kΩ,
CL = 20 pF,
pF
See Figure 1
VIPP = 2.5 V
Vn
Equivalent input noise voltage
f = 1 kHz,
See Figure 2
RS = 20 Ω,
BOM
Maximum output-swing bandwidth
VO = VOH,
RL = 10 kΩ
kΩ,
CL = 20 pF,
F
See Figure 1
B1
φm
Unity-gain bandwidth
Phase margin
V
VI = 10 mV,
See Figure 3
VI = 10 mV,
mV
CL = 20 pF
F,
CL = 20 pF,
F
f = B1,
See Figure 3
TYP
25°C
3.6
0°C
4
70°C
3
25°C
2.9
0°C
3.1
70°C
2.5
25°C
25
25°C
320
0°C
340
70°C
260
25°C
1.7
0°C
2
70°C
1.3
25°C
46°
0°C
47°
70°C
43°
UNIT
MAX
V/µs
nV/√Hz
kHz
MHz
operating characteristics at specified free-air temperature, VDD = 10 V
PARAMETER
TEST CONDITIONS
TA
TLC272C, TLC272AC,
TLC272BC, TLC277C
MIN
VIPP = 1 V
SR
Slew rate at unity gain
RL = 10 kΩ,
CL = 20 pF,
pF
See Figure 1
VIPP = 5.5 V
Vn
Equivalent input noise voltage
f = 1 kHz,
See Figure 2
RS = 20 Ω,
BOM
Maximum output-swing bandwidth
VO = VOH,
RL = 10 kΩ
kΩ,
F
CL = 20 pF,
See Figure 1
V
VI = 10 mV,
See Figure 3
CL = 20 pF,
F
B1
φm
12
Unity-gain bandwidth
Phase margin
VI = 10 mV,
mV
CL = 20 pF
F,
POST OFFICE BOX 655303
f = B1,
See Figure 3
• DALLAS, TEXAS 75265
TYP
25°C
5.3
0°C
5.9
70°C
4.3
25°C
4.6
0°C
5.1
70°C
3.8
25°C
25
25°C
200
0°C
220
70°C
140
25°C
2.2
0°C
2.5
70°C
1.8
25°C
49°
0°C
50°
70°C
46°
UNIT
MAX
V/µs
nV/√Hz
kHz
MHz
TLC272, TLC272A, TLC272B, TLC272Y, TLC277
LinCMOS PRECISION DUAL OPERATIONAL AMPLIFIERS
SLOS091B – OCTOBER 1987 – REVISED AUGUST 1994
operating characteristics at specified free-air temperature, VDD = 5 V
PARAMETER
TEST CONDITIONS
TA
TLC272I, TLC272AI,
TLC272BI, TLC277I
MIN
VIPP = 1 V
SR
Slew rate at unity gain
RL = 10 kΩ,
CL = 20 pF,
pF
See Figure 1
VIPP = 2.5 V
Vn
Equivalent input noise voltage
f = 1 kHz,
See Figure 2
RS = 20 Ω,
BOM
Maximum output-swing bandwidth
VO = VOH,
RL = 10 kΩ
kΩ,
CL = 20 pF,
F
See Figure 1
V
VI = 10 mV,
See Figure 3
CL = 20 pF,
F
B1
φm
Unity-gain bandwidth
Phase margin
VI = 10 mV,
mV
CL = 20 pF
F,
f = B1,
See Figure 3
TYP
25°C
3.6
– 40°C
4.5
85°C
2.8
25°C
2.9
– 40°C
3.5
85°C
2.3
25°C
25
25°C
320
– 40°C
380
85°C
250
25°C
1.7
– 40°C
2.6
85°C
1.2
25°C
46°
– 40°C
49°
85°C
43°
UNIT
MAX
V/µs
nV/√Hz
kHz
MHz
operating characteristics at specified free-air temperature, VDD = 10 V
PARAMETER
TEST CONDITIONS
TA
TLC272I, TLC272AI,
TLC272BI, TLC277I
MIN
VIPP = 1 V
SR
Slew rate at unity gain
RL = 10 kΩ,
CL = 20 pF,
pF
See Figure 1
VIPP = 5.5 V
Vn
BOM
B1
φm
Equivalent input noise voltage
f = 1 kHz,
See Figure 2
RS = 20 Ω,
Maximum output-swing bandwidth
VO = VOH,
RL = 10 kΩ
kΩ,
F
CL = 20 pF,
See Figure 1
V
VI = 10 mV,
See Figure 3
CL = 20 pF,
F
Unity-gain bandwidth
Phase margin
VI = 10 mV,
mV
CL = 20 pF
F,
POST OFFICE BOX 655303
f = B1,
See Figure 3
• DALLAS, TEXAS 75265
TYP
25°C
5.3
– 40°C
6.8
85°C
4
25°C
4.6
– 40°C
5.8
85°C
3.5
25°C
25
25°C
200
– 40°C
260
85°C
130
25°C
2.2
– 40°C
3.1
85°C
1.7
25°C
49°
– 40°C
52°
85°C
46°
UNIT
MAX
V/µs
nV/√Hz
kHz
MHz
13
TLC272, TLC272A, TLC272B, TLC272Y, TLC277
LinCMOS PRECISION DUAL OPERATIONAL AMPLIFIERS
SLOS091B – OCTOBER 1987 – REVISED AUGUST 1994
operating characteristics at specified free-air temperature, VDD = 5 V
PARAMETER
TEST CONDITIONS
VIPP = 1 V
SR
Slew rate at unity gain
RL = 10 kΩ,
CL = 20 pF,
pF
See Figure 1
VIPP = 2.5 V
Vn
BOM
B1
φm
Equivalent input noise voltage
f = 1 kHz,
See Figure 2
RS = 20 Ω,
Maximum output-swing bandwidth
VO = VOH,
RL = 10 kΩ
kΩ,
F
CL = 20 pF,
See Figure 1
V
VI = 10 mV,
See Figure 3
CL = 20 pF,
F
Unity-gain bandwidth
Phase margin
VI = 10 mV,
mV
CL = 20 pF
F,
f = B1,
See Figure 3
TA
TLC272M, TLC277M
MIN
TYP
25°C
3.6
– 55°C
4.7
125°C
2.3
25°C
2.9
– 55°C
3.7
125°C
2
25°C
25
25°C
320
– 55°C
400
125°C
230
25°C
1.7
– 55°C
2.9
125°C
1.1
25°C
46°
– 55°C
49°
125°C
41°
MAX
UNIT
V/µs
nV/√Hz
kHz
MHz
operating characteristics at specified free-air temperature, VDD = 10 V
PARAMETER
TEST CONDITIONS
VIPP = 1 V
SR
Slew rate at unity gain
RL = 10 kΩ,
CL = 20 pF,
pF
See Figure 1
VIPP = 5.5 V
Vn
Equivalent input noise voltage
f = 1 kHz,
See Figure 2
RS = 20 Ω,
BOM
Maximum output-swing bandwidth
VO = VOH,
RL = 10 kΩ
kΩ,
F
CL = 20 pF,
See Figure 1
B1
φm
14
Unity-gain bandwidth
Phase margin
V
VI = 10 mV,
See Figure 3
VI = 10 mV,
mV
CL = 20 pF
F,
POST OFFICE BOX 655303
CL = 20 pF,
F
f = B1,
See Figure 3
• DALLAS, TEXAS 75265
TA
TLC272M, TLC277M
MIN
TYP
25°C
5.3
– 55°C
7.1
125°C
3.1
25°C
4.6
– 55°C
6.1
125°C
2.7
25°C
25
25°C
200
– 55°C
280
125°C
110
25°C
2.2
– 55°C
3.4
125°C
1.6
25°C
49°
– 55°C
52°
125°C
44°
MAX
UNIT
V/µs
nV/√Hz
kHz
MHz
TLC272, TLC272A, TLC272B, TLC272Y, TLC277
LinCMOS PRECISION DUAL OPERATIONAL AMPLIFIERS
SLOS091B – OCTOBER 1987 – REVISED AUGUST 1994
operating characteristics, VDD = 5 V, TA = 25°C
PARAMETER
TEST CONDITIONS
MAX
UNIT
3.6
RS = 20 Ω,
See Figure 2
25
nV/√Hz
VO = VOH,
See Figure 1
CL = 20 pF,
RL = 10 kΩ,
320
kHz
VI = 10 mV,
VI = 10 mV,
See Figure 3
CL = 20 pF,
See Figure 3
1.7
MHz
f = B1,
CL = 20 pF,
46°
Slew rate at unity gain
RL = 10 kΩ,,
See Figure 1
CL = 20 pF,,
Vn
Equivalent input noise voltage
f = 1 kHz,
BOM
Maximum output-swing bandwidth
B1
Unity-gain bandwidth
Phase margin
TYP
VIPP = 1 V
VIPP = 2.5 V
SR
φm
TLC272Y
MIN
V/µs
2.9
operating characteristics, VDD = 10 V, TA = 25°C
PARAMETER
TEST CONDITIONS
TYP
MAX
UNIT
VIPP = 1 V
VIPP = 5.5 V
5.3
RS = 20 Ω,
See Figure 2
25
nV/√Hz
CL = 20 pF,
RL = 10 kΩ,
200
kHz
CL = 20 pF,
See Figure 3
2.2
MHz
f = B1,
CL = 20 pF,
49°
SR
Slew rate at unity gain
RL = 10 kΩ,,
See Figure 1
CL = 20 pF,,
Vn
Equivalent input noise voltage
f = 1 kHz,
BOM
Maximum output-swing bandwidth
VO = VOH,
See Figure 1
B1
Unity-gain bandwidth
φm
Phase margin
VI = 10 mV,
VI = 10 mV,
See Figure 3
POST OFFICE BOX 655303
TLC272Y
MIN
• DALLAS, TEXAS 75265
4.6
V/µs
15
TLC272, TLC272A, TLC272B, TLC272Y, TLC277
LinCMOS PRECISION DUAL OPERATIONAL AMPLIFIERS
SLOS091B – OCTOBER 1987 – REVISED AUGUST 1994
PARAMETER MEASUREMENT INFORMATION
single-supply versus split-supply test circuits
Because the TLC272 and TLC277 are optimized for single-supply operation, circuit configurations used for the
various tests often present some inconvenience since the input signal, in many cases, must be offset from
ground. This inconvenience can be avoided by testing the device with split supplies and the output load tied to
the negative rail. A comparison of single-supply versus split-supply test circuits is shown below. The use of either
circuit gives the same result.
VDD +
VDD
–
–
VO
VO
+
CL
+
VI
VI
RL
CL
RL
VDD –
(a) SINGLE SUPPLY
(b) SPLIT SUPPLY
Figure 1. Unity-Gain Amplifier
2 kΩ
VDD
VDD +
–
–
20 Ω
2 kΩ
1/2 VDD
VO
VO
+
+
20 Ω
20 Ω
20 Ω
VDD –
(a) SINGLE SUPPLY
(b) SPLIT SUPPLY
Figure 2. Noise-Test Circuit
10 kΩ
VDD
VDD +
100 Ω
–
100 Ω
–
VI
10 kΩ
VI
VO
+
+
1/2 VDD
VO
CL
CL
VDD –
(a) SINGLE SUPPLY
(b) SPLIT SUPPLY
Figure 3. Gain-of-100 Inverting Amplifier
16
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
TLC272, TLC272A, TLC272B, TLC272Y, TLC277
LinCMOS PRECISION DUAL OPERATIONAL AMPLIFIERS
SLOS091B – OCTOBER 1987 – REVISED AUGUST 1994
PARAMETER MEASUREMENT INFORMATION
input bias current
Because of the high input impedance of the TLC272 and TLC277 operational amplifiers, attempts to measure
the input bias current can result in erroneous readings. The bias current at normal room ambient temperature
is typically less than 1 pA, a value that is easily exceeded by leakages on the test socket. Two suggestions are
offered to avoid erroneous measurements:
1. Isolate the device from other potential leakage sources. Use a grounded shield around and between the
device inputs (see Figure 4). Leakages that would otherwise flow to the inputs are shunted away.
2. Compensate for the leakage of the test socket by actually performing an input bias current test (using
a picoammeter) with no device in the test socket. The actual input bias current can then be calculated
by subtracting the open-socket leakage readings from the readings obtained with a device in the test
socket.
One word of caution: many automatic testers as well as some bench-top operational amplifier testers use the
servo-loop technique with a resistor in series with the device input to measure the input bias current (the voltage
drop across the series resistor is measured and the bias current is calculated). This method requires that a
device be inserted into the test socket to obtain a correct reading; therefore, an open-socket reading is not
feasible using this method.
8
5
V = VIC
1
4
Figure 4. Isolation Metal Around Device Inputs
(JG and P packages)
low-level output voltage
To obtain low-supply-voltage operation, some compromise was necessary in the input stage. This compromise
results in the device low-level output being dependent on both the common-mode input voltage level as well
as the differential input voltage level. When attempting to correlate low-level output readings with those quoted
in the electrical specifications, these two conditions should be observed. If conditions other than these are to
be used, please refer to Figures 14 through 19 in the Typical Characteristics of this data sheet.
input offset voltage temperature coefficient
Erroneous readings often result from attempts to measure temperature coefficient of input offset voltage. This
parameter is actually a calculation using input offset voltage measurements obtained at two different
temperatures. When one (or both) of the temperatures is below freezing, moisture can collect on both the device
and the test socket. This moisture results in leakage and contact resistance, which can cause erroneous input
offset voltage readings. The isolation techniques previously mentioned have no effect on the leakage since the
moisture also covers the isolation metal itself, thereby rendering it useless. It is suggested that these
measurements be performed at temperatures above freezing to minimize error.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
17
TLC272, TLC272A, TLC272B, TLC272Y, TLC277
LinCMOS PRECISION DUAL OPERATIONAL AMPLIFIERS
SLOS091B – OCTOBER 1987 – REVISED AUGUST 1994
PARAMETER MEASUREMENT INFORMATION
full-power response
Full-power response, the frequency above which the operational amplifier slew rate limits the output voltage
swing, is often specified two ways: full-linear response and full-peak response. The full-linear response is
generally measured by monitoring the distortion level of the output while increasing the frequency of a sinusoidal
input signal until the maximum frequency is found above which the output contains significant distortion. The
full-peak response is defined as the maximum output frequency, without regard to distortion, above which full
peak-to-peak output swing cannot be maintained.
Because there is no industry-wide accepted value for significant distortion, the full-peak response is specified
in this data sheet and is measured using the circuit of Figure 1. The initial setup involves the use of a sinusoidal
input to determine the maximum peak-to-peak output of the device (the amplitude of the sinusoidal wave is
increased until clipping occurs). The sinusoidal wave is then replaced with a square wave of the same
amplitude. The frequency is then increased until the maximum peak-to-peak output can no longer be maintained
(Figure 5). A square wave is used to allow a more accurate determination of the point at which the maximum
peak-to-peak output is reached.
(a) f = 1 kHz
(b) BOM > f > 1 kHz
(c) f = BOM
(d) f > BOM
Figure 5. Full-Power-Response Output Signal
test time
Inadequate test time is a frequent problem, especially when testing CMOS devices in a high-volume,
short-test-time environment. Internal capacitances are inherently higher in CMOS than in bipolar and BiFET
devices and require longer test times than their bipolar and BiFET counterparts. The problem becomes more
pronounced with reduced supply levels and lower temperatures.
18
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
TLC272, TLC272A, TLC272B, TLC272Y, TLC277
LinCMOS PRECISION DUAL OPERATIONAL AMPLIFIERS
SLOS091B – OCTOBER 1987 – REVISED AUGUST 1994
TYPICAL CHARACTERISTICS
Table of Graphs
FIGURE
VIO
αVIO
Input offset voltage
Distribution
6, 7
Temperature coefficient of input offset voltage
Distribution
8, 9
VOH
High-level
g
output voltage
g
vs High-level
High level output
out ut current
vs Supply
y voltage
g
vs Free-air temperature
10, 11
12
13
VOL
Low level output voltage
Low-level
vs Common-mode
Common mode input
in ut voltage
vs Differential input voltage
g
vs Free-air temperature
vs Low-level output current
14, 15
16
17
18, 19
AVD
Large-signal
g
g
differential voltage
g amplification
vs Su
Supply
ly voltage
vs Free-air temperature
vs Frequency
20
21
32, 33
IIB
IIO
Input bias current
vs Free-air temperature
22
Input offset current
vs Free-air temperature
22
VIC
Common-mode input voltage
vs Supply voltage
23
IDD
Supply current
vs Supply
y voltage
g
vs Free-air temperature
24
25
SR
Slew rate
vs Supply
y voltage
g
vs Free-air temperature
26
27
Normalized slew rate
vs Free-air temperature
28
Maximum peak-to-peak output voltage
vs Frequency
29
B1
Unity gain bandwidth
Unity-gain
vs Free-air temperature
vs Supply voltage
30
31
φm
Phase margin
g
vs Su
Supply
ly voltage
vs Free-air temperature
vs Load capacitance
34
35
36
Vn
Equivalent input noise voltage
vs Frequency
37
Phase shift
vs Frequency
32, 33
VO(PP)
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
19
TLC272, TLC272A, TLC272B, TLC272Y, TLC277
LinCMOS PRECISION DUAL OPERATIONAL AMPLIFIERS
SLOS091B – OCTOBER 1987 – REVISED AUGUST 1994
TYPICAL CHARACTERISTICS
DISTRIBUTION OF TLC272
INPUT OFFSET VOLTAGE
DISTRIBUTION OF TLC272
INPUT OFFSET VOLTAGE
Percentage of Units – %
50
40
ÌÌÌÌ
ÌÌÌÌÌÌÌÌÌÌÌÌ
ÌÌÌÌÌ
ÌÌÌÌÌÌÌÌÌÌÌÌ
ÌÌÌÌ
ÌÌÌÌÌ
ÌÌÌÌÌ
60
753 Amplifiers Tested From 6 Wafer Lots
VDD = 5 V
TA = 25°C
P Package
50
Percentage of Units – %
60
30
20
40
ÌÌÌÌÌÌÌÌÌÌÌ
ÌÌÌÌ
ÌÌÌÌÌÌÌÌÌÌÌ
ÌÌÌÌ
ÌÌÌÌ
753 Amplifiers Tested From 6 Wafer Lots
VDD = 10 V
TA = 25°C
P Package
30
20
10
10
0
–5
0
–4
–3 –2 –1
0
1
2
3
VIO – Input Offset Voltage – mV
4
–5
5
–4
DISTRIBUTION OF TLC272 AND TLC277
INPUT OFFSET VOLTAGE
TEMPERATURE COEFFICIENT
40
DISTRIBUTION OF TLC272 AND TLC277
INPUT OFFSET VOLTAGE
TEMPERATURE COEFFICIENT
ÌÌÌÌÌÌÌÌÌÌÌÌ
ÌÌÌÌÌÌÌÌÌÌÌÌ
ÌÌÌÌÌÌÌÌÌÌÌÌ
ÌÌÌÌÌÌÌÌÌÌÌÌ
ÌÌÌÌÌÌÌÌÌÌÌÌ
ÌÌÌÌÌÌÌÌÌÌÌÌ
ÌÌÌÌÌÌÌÌÌÌÌÌ
ÌÌÌÌÌÌÌÌÌÌÌÌ
60
324 Amplifiers Tested From 8 Wafer Lots
VDD = 5 V
TA = 25°C to 125°C
P Package
Outliers:
(1) 20.5 µV/°C
50
Percentage of Units – %
Percentage of Units – %
50
30
20
40
324 Amplifiers Tested From 8 Wafer Lots
VDD = 5 V
TA = 25°C to 125°C
P Package
Outliers:
(1) 21.2 µV/°C
30
20
10
10
0
0
2
– 10 – 8 – 6 – 4 – 2
4
6
8
αVIO – Temperature Coefficient – µV/°C
10
0
2
4
6
8
– 10 – 8 – 6 – 4 – 2 0
αVIO – Temperature Coefficient – µV/°C
Figure 9
Figure 8
20
5
4
Figure 7
Figure 6
60
–3 –2 –1
0
1
2
3
VIO – Input Offset Voltage – mV
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
Á
10
TLC272, TLC272A, TLC272B, TLC272Y, TLC277
LinCMOS PRECISION DUAL OPERATIONAL AMPLIFIERS
SLOS091B – OCTOBER 1987 – REVISED AUGUST 1994
TYPICAL CHARACTERISTICS†
HIGH-LEVEL OUTPUT VOLTAGE
vs
HIGH-LEVEL OUTPUT CURRENT
HIGH-LEVEL OUTPUT VOLTAGE
vs
HIGH-LEVEL OUTPUT CURRENT
16
VID = 100 mV
TA = 25°C
See Note A
4
VOH
V
OH – High-Level Output Voltage – V
VOH
VOH – High-Level Output Voltage – V
5
VDD = 5 V
3
VDD = 4 V
VDD = 3 V
2
ÁÁ
ÁÁ
ÁÁ
ÁÁ
ÁÁ
ÁÁ
1
0
–2
–4
–6
–8
IOH – High-Level Output Current – mA
0
– 10
14
VDD = 16 V
VID = 100 mV
TA = 25°C
12
10
8
VDD = 10 V
6
4
2
0
0
– 5 – 10 – 15 – 20 – 25 – 30 – 35 – 40
IOH – High-Level Output Current – mA
NOTE A: The 3-V curve only applies to the C version.
Figure 11
Figure 10
HIGH-LEVEL OUTPUT VOLTAGE
vs
SUPPLY VOLTAGE
14
12
ÌÌÌÌÌ
ÌÌÌÌ
ÌÌÌÌÌ
ÌÌÌÌ
VDD – 1.6
VID = 100 mV
RL = 10 kΩ
TA = 25°C
VOH
V
OH – High-Level Output Voltage – V
VOH
V
OH – High-Level Output Voltage – V
16
HIGH-LEVEL OUTPUT VOLTAGE
vs
FREE-AIR TEMPERATURE
10
ÁÁ
ÁÁ
ÁÁ
8
6
IOH = – 5 mA
VID = 100 mA
VDD – 1.7
VDD = 5 V
VDD –1.8
VDD – 1.9
VDD – 2
VDD = 10 V
VDD –2.1
ÁÁ
ÁÁ
ÁÁ
4
2
0
0
2
4
6
8
10
12
VDD – Supply Voltage – V
14
16
VDD – 2.2
VDD –2.3
VDD –2.4
– 75
– 50
Figure 12
– 25
0
20
50
75 100
TA – Free-Air Temperature – °C
125
Figure 13
† Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
21
TLC272, TLC272A, TLC272B, TLC272Y, TLC277
LinCMOS PRECISION DUAL OPERATIONAL AMPLIFIERS
SLOS091B – OCTOBER 1987 – REVISED AUGUST 1994
TYPICAL CHARACTERISTICS†
LOW-LEVEL OUTPUT VOLTAGE
vs
COMMON-MODE INPUT VOLTAGE
LOW-LEVEL OUTPUT VOLTAGE
vs
COMMON-MODE INPUT VOLTAGE
500
VDD = 5 V
IOL = 5 mA
650
VOL – Low-Level Output Voltage – mV
VOL
V
VOL
OL – Low-Level Output Voltage – mV
700
TA = 25°C
600
550
VID = – 100 mV
500
450
ÁÁ
ÁÁ
ÁÁ
VID = – 1 V
350
300
0
450
400
VID = – 100 mV
0.5
1
1.5
2
2.5
3
3.5
VIC – Common-Mode Input Voltage – V
VID = – 1 V
350
VID = – 2.5 V
ÁÁ
ÁÁ
400
VDD = 10 V
IOL = 5 mA
TA = 25°C
4
300
250
0
1
3
5
7
9
2
4
6
8
VIC – Common-Mode Input Voltage – V
Figure 14
Figure 15
LOW-LEVEL OUTPUT VOLTAGE
vs
DIFFERENTIAL INPUT VOLTAGE
LOW-LEVEL OUTPUT VOLTAGE
vs
FREE-AIR TEMPERATURE
900
IOL = 5 mA
VIC = |VID/2|
TA = 25°C
700
V
VOL
OL – Low-Level Output Voltage – mV
VOL – Low-Level Output Voltage – mV
VOL
800
600
500
VDD = 5 V
400
300
ÁÁ
ÁÁ
ÁÁ
VDD = 10 V
200
100
0
800
700
IOL = 5 mA
VID = – 1 V
VIC = 0.5 V
VDD = 5 V
600
500
400
ÁÁ
ÁÁ
ÁÁ
VDD = 10 V
300
200
100
0
–1
– 2 – 3 – 4 – 5 – 6 – 7 – 8 – 9 – 10
VID – Differential Input Voltage – V
0
– 75
– 50
Figure 16
– 25
0
25
50
75 100
TA – Free-Air Temperature – °C
Figure 17
† Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.
22
10
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
125
TLC272, TLC272A, TLC272B, TLC272Y, TLC277
LinCMOS PRECISION DUAL OPERATIONAL AMPLIFIERS
SLOS091B – OCTOBER 1987 – REVISED AUGUST 1994
TYPICAL CHARACTERISTICS†
LOW-LEVEL OUTPUT VOLTAGE
vs
LOW-LEVEL OUTPUT CURRENT
V
VOL
OL – Low-Level Output Voltage – V
0.9
0.8
0.7
ÌÌÌÌ
ÌÌÌÌ
ÌÌÌÌ
3.0
VID = – 1 V
VIC = 0.5 V
TA = 25°C
See Note A
V
VOL
OL – Low-Level Output Voltage – V
1.0
LOW-LEVEL OUTPUT VOLTAGE
vs
LOW-LEVEL OUTPUT CURRENT
VDD = 5 V
VDD = 4 V
0.6
VDD = 3 V
0.5
0.4
ÁÁ
ÁÁ
2.5
2.0
0.2
0.1
0
0
1
2
3
4
5
6
7
IOL – Low-Level Output Current – mA
VID = – 1 V
VIC = 0.5 V
TA = 25°C
VDD = 16 V
VDD = 10 V
1.5
ÁÁ
ÁÁ
ÁÁ
0.3
ÌÌÌÌÌ
ÌÌÌÌ
ÌÌÌÌ
ÌÌÌÌÌ
ÌÌÌÌ
1.0
0.5
8
0
0
5
10
15
20
25
IOL – Low-Level Output Current – mA
30
NOTE A: The 3-V curve only applies to the C version.
Figure 19
Figure 18
LARGE-SIGNAL
DIFFERENTIAL VOLTAGE AMPLIFICATION
vs
SUPPLY VOLTAGE
60
ÌÌÌÌ
50
TA = 0°C
40
ÌÌÌÌ
ÌÌÌÌ
ÁÁ
ÌÌÌÌÌÁÁ
ÁÁ
30
TA = 25°C
TA = 85°C
20
TA = 125°C
10
0
0
2
4
6
8
10
12
VDD – Supply Voltage – V
14
16
RL = 10 kΩ
45
AVD
A
VD – Large-Signal Differential
Voltage Amplification – V/mV
AVD
AVD – Large-Signal Differential
Voltage Amplification – V/mV
50
TA = – 55°C
RL = 10 kΩ
ÁÁ
ÁÁ
ÁÁ
LARGE-SIGNAL
DIFFERENTIAL VOLTAGE AMPLIFICATION
vs
FREE-AIR TEMPERATURE
40
VDD = 10 V
35
30
25
20
VDD = 5 V
15
10
5
0
– 75
– 50
Figure 20
– 25
0
25
50
75
100
TA – Free-Air Temperature – °C
125
Figure 21
† Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
23
TLC272, TLC272A, TLC272B, TLC272Y, TLC277
LinCMOS PRECISION DUAL OPERATIONAL AMPLIFIERS
SLOS091B – OCTOBER 1987 – REVISED AUGUST 1994
TYPICAL CHARACTERISTICS†
COMMON-MODE
INPUT VOLTAGE POSITIVE LIMIT
vs
SUPPLY VOLTAGE
10000
16
VDD = 10 V
VIC = 5 V
See Note A
ÌÌ
1000
VIC – Common-Mode Input Voltage – V
I IB and I IO – Input Bias and Offset Currents – pA
INPUT BIAS CURRENT AND INPUT OFFSET CURRENT
vs
FREE-AIR TEMPERATURE
IIB
100
ÌÌ
ÌÌ
IIO
10
1
0.1
25
TA = 25°C
14
12
10
8
6
4
2
0
35
45 55 65 75 85 95 105 115 125
TA – Free-Air Temperature – °C
NOTE A: The typical values of input bias current and input
offset current below 5 pA were determined mathematically.
0
2
4
6
8
10
12
VDD – Supply Voltage – V
14
16
0
25
50
75
100
– 25
TA – Free-Air Temperature – °C
125
Figure 23
Figure 22
SUPPLY CURRENT
vs
SUPPLY VOLTAGE
SUPPLY CURRENT
vs
FREE-AIR TEMPERATURE
5
4
VO = VDD/2
No Load
3.5
VO = VDD/2
No Load
TA = – 55°C
4
3.5
ÌÌÌÌ
ÌÌÌÌ
3
TA = 25°C
2.5
2
1.5
ÌÌÌ
TA = 0°C
ÌÌÌÌ
ÌÌÌÌ
ÌÌÌÌ
1
TA = 70°C
0.5
I DD – Supply Current – mA
I DD – Supply Current – mA
4.5
3
2.5
VDD = 10 V
2
1.5
VDD = 5 V
1
0.5
TA = 125°C
0
0
2
4
6
8
10
12
VDD – Supply Voltage – V
14
16
0
– 75
– 50
Figure 24
Figure 25
† Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.
24
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
TLC272, TLC272A, TLC272B, TLC272Y, TLC277
LinCMOS PRECISION DUAL OPERATIONAL AMPLIFIERS
SLOS091B – OCTOBER 1987 – REVISED AUGUST 1994
TYPICAL CHARACTERISTICS†
SLEW RATE
vs
FREE-AIR TEMPERATURE
SLEW RATE
vs
SUPPLY VOLTAGE
8
8
AV = 1
VIPP = 1 V
RL = 10 kΩ
CL = 20 pF
TA = 25°C
See Figure 1
6
7
5
4
3
3
1
1
0
4
6
8
10
12
VDD – Supply Voltage – V
14
VDD = 10 V
VIPP = 1 V
4
2
2
VDD = 10 V
VIPP = 5.5 V
5
2
0
VDD = 5 V
VIPP = 1 V
VDD = 5 V
VIPP = 2.5 V
0
– 75
16
– 50
NORMALIZED SLEW RATE
vs
FREE-AIR TEMPERATURE
VO(PP) – Maximum Peak-to-Peak Output Voltage – V
AV = 1
VIPP = 1 V
RL = 10 kΩ
CL = 20 pF
1.4
VDD = 10 V
Normalized Slew Rate
1.2
VDD = 5 V
1.0
0.9
0.8
0.7
0.6
0.5
– 75
– 50
– 25
0
25
125
MAXIMUM PEAK OUTPUT VOLTAGE
vs
FREQUENCY
1.5
1.1
– 25
0
25
50
75 100
TA – Free-Air Temperature – °C
Figure 27
Figure 26
1.3
AV = 1
RL = 10 kΩ
CL = 20 pF
See Figure 1
6
SR – Slew Rate – V/ µs
SR – Slew Rate – V/ µs
7
50
75
100
125
10
VDD = 10 V
9
8
TA = 125°C
TA = 25°C
TA = – 55°C
7
6
5
VDD = 5 V
4
3
RL = 10 kΩ
See Figure 1
2
1
0
10
TA – Free-Air Temperature – °C
100
1000
10000
f – Frequency – kHz
Figure 29
Figure 28
† Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
25
TLC272, TLC272A, TLC272B, TLC272Y, TLC277
LinCMOS PRECISION DUAL OPERATIONAL AMPLIFIERS
SLOS091B – OCTOBER 1987 – REVISED AUGUST 1994
TYPICAL CHARACTERISTICS†
UNITY-GAIN BANDWIDTH
vs
SUPPLY VOLTAGE
UNITY-GAIN BANDWIDTH
vs
FREE-AIR TEMPERATURE
2.5
VDD = 5 V
VI = 10 mV
CL = 20 pF
See Figure 3
2.5
B1 – Unity-Gain Bandwidth – MHz
B1 – Unity-Gain Bandwidth – MHz
3.0
2.0
1.5
1.0
– 75
VI = 10 mV
CL = 20 pF
TA = 25°C
See Figure 3
2.0
1.5
1.0
– 50
– 25
0
25
50
75
100
0
125
2
4
6
8
10
12
14
VDD – Supply Voltage – V
TA – Free-Air Temperature – °C
Figure 31
Figure 30
LARGE-SIGNAL DIFFERENTIAL VOLTAGE
AMPLIFICATION AND PHASE SHIFT
vs
FREQUENCY
107
Á
Á
VDD = 5 V
RL = 10 kΩ
TA = 25°C
10 5
0°
10 4
30°
AVD
10 3
60°
10 2
90°
Phase Shift
101
120°
1
150°
0.1
10
Phase Shift
AVD
AVD – Large-Signal Differential
Voltage Amplification
10 6
180°
100
1k
10 k
100 k
1M
10 M
f – Frequency – Hz
Figure 32
† Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.
26
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
16
TLC272, TLC272A, TLC272B, TLC272Y, TLC277
LinCMOS PRECISION DUAL OPERATIONAL AMPLIFIERS
SLOS091B – OCTOBER 1987 – REVISED AUGUST 1994
TYPICAL CHARACTERISTICS†
LARGE-SIGNAL DIFFERENTIAL VOLTAGE
AMPLIFICATION AND PHASE SHIFT
vs
FREQUENCY
10 7
VDD = 10 V
RL = 10 kΩ
TA = 25°C
ÁÁ
ÁÁ
10 5
0°
10 4
30°
Phase Shift
AVD
A
VD – Large-Signal Differential
Voltage Amplification
10 6
AVD
10 3
60°
10 2
90°
Phase Shift
101
120°
1
150°
0.1
10
100
1k
10 k
100 k
1M
180°
10 M
f – Frequency – Hz
Figure 33
PHASE MARGIN
vs
SUPPLY VOLTAGE
PHASE MARGIN
vs
FREE-AIR TEMPERATURE
53°
50°
VDD = 5 V
VI = 10 mV
CL = 20 pF
See Figure 3
52°
48°
φm
m – Phase Margin
φm
m – Phase Margin
51°
50°
49°
48°
VI = 10 mV
CL = 20 pF
TA = 25°C
See Figure 3
47°
46°
2
4
6
8
10
12
14
44°
42°
45°
0
46°
16
40°
–75
–50
–25
0
25
50
75
100
125
TA – Free-Air Temperature – °C
VDD – Supply Voltage – V
Figure 34
Figure 35
† Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
27
TLC272, TLC272A, TLC272B, TLC272Y, TLC277
LinCMOS PRECISION DUAL OPERATIONAL AMPLIFIERS
SLOS091B – OCTOBER 1987 – REVISED AUGUST 1994
TYPICAL CHARACTERISTICS
PHASE MARGIN
vs
CAPACITIVE LOAD
50°
VDD = 5 V
VI = 10 mV
TA = 25°C
See Figure 3
φm
m – Phase Margin
45°
40°
35°
30°
25°
VN
V n – Equivalent Input Noise Voltage – nV/ Hz
EQUIVALENT INPUT NOISE VOLTAGE
vs
FREQUENCY
400
VDD = 5 V
RS = 20 Ω
TA = 25°C
See Figure 2
300
200
100
0
0
10
20
30
40
50
60
70
80
90 100
1
CL – Capacitive Load – pF
100
f – Frequency – Hz
Figure 36
28
10
Figure 37
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
1000
TLC272, TLC272A, TLC272B, TLC272Y, TLC277
LinCMOS PRECISION DUAL OPERATIONAL AMPLIFIERS
SLOS091B – OCTOBER 1987 – REVISED AUGUST 1994
APPLICATION INFORMATION
single-supply operation
While the TLC272 and TLC277 perform well using dual power supplies (also called balanced or split supplies),
the design is optimized for single-supply operation. This design includes an input common-mode voltage range
that encompasses ground as well as an output voltage range that pulls down to ground. The supply voltage
range extends down to 3 V (C-suffix types), thus allowing operation with supply levels commonly available for
TTL and HCMOS; however, for maximum dynamic range, 16-V single-supply operation is recommended.
Many single-supply applications require that a voltage be applied to one input to establish a reference level that
is above ground. A resistive voltage divider is usually sufficient to establish this reference level (see Figure 38).
The low input bias current of the TLC272 and TLC277 permits the use of very large resistive values to implement
the voltage divider, thus minimizing power consumption.
The TLC272 and TLC277 work well in conjunction with digital logic; however, when powering both linear devices
and digital logic from the same power supply, the following precautions are recommended:
1. Power the linear devices from separate bypassed supply lines (see Figure 39); otherwise, the linear
device supply rails can fluctuate due to voltage drops caused by high switching currents in the digital
logic.
2. Use proper bypass techniques to reduce the probability of noise-induced errors. Single capacitive
decoupling is often adequate; however, high-frequency applications may require RC decoupling.
VDD
R4
R1
R2
–
VI
VO
+
VREF
R3
V
REF
V
C
0.01 µF
O
+
+
V
(V
)
R3
DD R1
REF
R3
* VI ) R4
)
R2
V
REF
Figure 38. Inverting Amplifier With Voltage Reference
–
OUT
Logic
Logic
Logic
Power
Supply
+
(a) COMMON SUPPLY RAILS
–
Logic
Logic
Logic
+
OUT
Power
Supply
(b) SEPARATE BYPASSED SUPPLY RAILS (preferred)
Figure 39. Common vs Separate Supply Rails
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
29
TLC272, TLC272A, TLC272B, TLC272Y, TLC277
LinCMOS PRECISION DUAL OPERATIONAL AMPLIFIERS
SLOS091B – OCTOBER 1987 – REVISED AUGUST 1994
APPLICATION INFORMATION
input characteristics
The TLC272 and TLC277 are specified with a minimum and a maximum input voltage that, if exceeded at either
input, could cause the device to malfunction. Exceeding this specified range is a common problem, especially
in single-supply operation. Note that the lower range limit includes the negative rail, while the upper range limit
is specified at VDD – 1 V at TA = 25°C and at VDD – 1.5 V at all other temperatures.
The use of the polysilicon-gate process and the careful input circuit design gives the TLC272 and TLC277 very
good input offset voltage drift characteristics relative to conventional metal-gate processes. Offset voltage drift
in CMOS devices is highly influenced by threshold voltage shifts caused by polarization of the phosphorus
dopant implanted in the oxide. Placing the phosphorus dopant in a conductor (such as a polysilicon gate)
alleviates the polarization problem, thus reducing threshold voltage shifts by more than an order of magnitude.
The offset voltage drift with time has been calculated to be typically 0.1 µV/month, including the first month of
operation.
Because of the extremely high input impedance and resulting low bias current requirements, the TLC272 and
TLC277 are well suited for low-level signal processing; however, leakage currents on printed-circuit boards and
sockets can easily exceed bias current requirements and cause a degradation in device performance. It is good
practice to include guard rings around inputs (similar to those of Figure 4 in the Parameter Measurement
Information section). These guards should be driven from a low-impedance source at the same voltage level
as the common-mode input (see Figure 40).
Unused amplifiers should be connected as grounded unity-gain followers to avoid possible oscillation.
noise performance
The noise specifications in operational amplifier circuits are greatly dependent on the current in the first-stage
differential amplifier. The low input bias current requirements of the TLC272 and TLC277 result in a very low
noise current, which is insignificant in most applications. This feature makes the devices especially favorable
over bipolar devices when using values of circuit impedance greater than 50 kΩ, since bipolar devices exhibit
greater noise currents.
–
OUT
+
+
(b) INVERTING AMPLIFIER
OUT
VI
+
–
(a) NONINVERTING AMPLIFIER
–
VI
VI
OUT
(c) UNITY-GAIN AMPLIFIER
Figure 40. Guard-Ring Schemes
output characteristics
The output stage of the TLC272 and TLC277 is designed to sink and source relatively high amounts of current
(see typical characteristics). If the output is subjected to a short-circuit condition, this high current capability can
cause device damage under certain conditions. Output current capability increases with supply voltage.
All operating characteristics of the TLC272 and TLC277 are measured using a 20-pF load. The devices can
drive higher capacitive loads; however, as output load capacitance increases, the resulting response pole
occurs at lower frequencies, thereby causing ringing, peaking, or even oscillation (see Figure 41). In many
cases, adding a small amount of resistance in series with the load capacitance alleviates the problem.
30
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
TLC272, TLC272A, TLC272B, TLC272Y, TLC277
LinCMOS PRECISION DUAL OPERATIONAL AMPLIFIERS
SLOS091B – OCTOBER 1987 – REVISED AUGUST 1994
APPLICATION INFORMATION
output characteristics (continued)
(b) CL = 130 pF, RL = NO LOAD
(a) CL = 20 pF, RL = NO LOAD
2.5 V
–
VO
+
VI
TA = 25°C
f = 1 kHz
VIPP = 1 V
CL
– 2.5 V
(c) CL = 150 pF, RL = NO LOAD
(d) TEST CIRCUIT
Figure 41. Effect of Capacitive Loads and Test Circuit
Although the TLC272 and TLC277 possess excellent high-level output voltage and current capability, methods
for boosting this capability are available, if needed. The simplest method involves the use of a pullup resistor
(RP) connected from the output to the positive supply rail (see Figure 42). There are two disadvantages to the
use of this circuit. First, the NMOS pulldown transistor N4 (see equivalent schematic) must sink a comparatively
large amount of current. In this circuit, N4 behaves like a linear resistor with an on resistance between
approximately 60 Ω and 180 Ω, depending on how hard the operational amplifier input is driven. With very low
values of RP, a voltage offset from 0 V at the output occurs. Second, pullup resistor RP acts as a drain load to
N4 and the gain of the operational amplifier is reduced at output voltage levels where N5 is not supplying the
output current.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
31
TLC272, TLC272A, TLC272B, TLC272Y, TLC277
LinCMOS PRECISION DUAL OPERATIONAL AMPLIFIERS
SLOS091B – OCTOBER 1987 – REVISED AUGUST 1994
APPLICATION INFORMATION
output characteristics (continued)
VDD
VI
+
IP
RP
VO
–
C
IF
R2
R1
IL
RL
–
VO
VDD – VO
IF + IL + IP
ÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁ
+
Rp =
Ip = Pullup current required by
the operational amplifier
(typically 500 µA)
Figure 42. Resistive Pullup to Increase VOH
Figure 43. Compensation for Input Capacitance
feedback
Operational amplifier circuits almost always employ feedback, and since feedback is the first prerequisite for
oscillation, some caution is appropriate. Most oscillation problems result from driving capacitive loads
(discussed previously) and ignoring stray input capacitance. A small-value capacitor connected in parallel with
the feedback resistor is an effective remedy (see Figure 43). The value of this capacitor is optimized empirically.
electrostatic discharge protection
The TLC272 and TLC277 incorporate an internal electrostatic discharge (ESD) protection circuit that prevents
functional failures at voltages up to 2000 V as tested under MIL-STD-883C, Method 3015.2. Care should be
exercised, however, when handling these devices as exposure to ESD may result in the degradation of the
device parametric performance. The protection circuit also causes the input bias currents to be temperature
dependent and have the characteristics of a reverse-biased diode.
latch-up
Because CMOS devices are susceptible to latch-up due to their inherent parasitic thyristors, the TLC272 and
TLC277 inputs and outputs were designed to withstand –100-mA surge currents without sustaining latch-up;
however, techniques should be used to reduce the chance of latch-up whenever possible. Internal protection
diodes should not, by design, be forward biased. Applied input and output voltage should not exceed the supply
voltage by more than 300 mV. Care should be exercised when using capacitive coupling on pulse generators.
Supply transients should be shunted by the use of decoupling capacitors (0.1 µF typical) located across the
supply rails as close to the device as possible.
The current path established if latch-up occurs is usually between the positive supply rail and ground and can
be triggered by surges on the supply lines and/or voltages on either the output or inputs that exceed the supply
voltage. Once latch-up occurs, the current flow is limited only by the impedance of the power supply and the
forward resistance of the parasitic thyristor and usually results in the destruction of the device. The chance of
latch-up occurring increases with increasing temperature and supply voltages.
32
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
TLC272, TLC272A, TLC272B, TLC272Y, TLC277
LinCMOS PRECISION DUAL OPERATIONAL AMPLIFIERS
SLOS091B – OCTOBER 1987 – REVISED AUGUST 1994
APPLICATION INFORMATION
10 kΩ
10 kΩ
0.016 µF
0.016 µF
10 kΩ
–
10 kΩ
5V
10 kΩ
1/2
TLC272
–
1/2
TLC272
–
VI
1/2
TLC272
Low Pass
+
+
+
High Pass
5 kΩ
Band Pass
R = 5 kΩ(3/d-1) (see Note A)
NOTE A: d = damping factor, 1/Q
Figure 44. State-Variable Filter
12 V
VI
+
1/2
TLC272
H.P.
5082-2835
+
1/2
TLC272
–
0.5 µF
Mylar
N.O.
Reset
VO
–
100 kΩ
Figure 45. Positive-Peak Detector
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
33
TLC272, TLC272A, TLC272B, TLC272Y, TLC277
LinCMOS PRECISION DUAL OPERATIONAL AMPLIFIERS
SLOS091B – OCTOBER 1987 – REVISED AUGUST 1994
APPLICATION INFORMATION
VI
(see Note A)
100 kΩ
1.2 kΩ
0.47 µF
4.7 kΩ
–
TL431
20 kΩ
1/2
TLC272
0.1 µF
1 kΩ
TIP31
15 Ω
+
TIS193
250 µF,
25 V
+
–
VO
(see Note B)
10 kΩ
47 kΩ
0.01 µF
110 Ω
22 kΩ
NOTES: A. VI = 3.5 to 15 V
B. VO = 2 V, 0 to 1 A
Figure 46. Logic-Array Power Supply
VO (see Note A)
9V
10 kΩ
0.1 µF
9V
C
100 kΩ
–
1/2
TLC272
R2
10 kΩ
1/2
TLC272
VO (see Note B)
+
100 kΩ
fO
R1
47 kΩ
R3
NOTES: A. VO(PP) = 8 V
B. VO(PP) = 4 V
Figure 47. Single-Supply Function Generator
34
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
1
+ 4C(R2)
[R1
R3]
TLC272, TLC272A, TLC272B, TLC272Y, TLC277
LinCMOS PRECISION DUAL OPERATIONAL AMPLIFIERS
SLOS091B – OCTOBER 1987 – REVISED AUGUST 1994
APPLICATION INFORMATION
5V
VI –
+
10 kΩ
1/2
TLC277
100 kΩ
–
–
1/2
TLC277
VO
+
10 kΩ
–
10 kΩ
1/2
TLC277
95 kΩ
R1,10 kΩ
(see Note A)
+
VI +
–5 V
NOTE B: CMRR adjustment must be noninductive.
Figure 48. Low-Power Instrumentation Amplifier
5V
–
R
10 MΩ
R
10 MΩ
1/2
TLC272
VO
+
VI
2C
540 pF
f NOTCH
R/2
5 MΩ
C
270 pF
+
1
2pRC
C
270 pF
Figure 49. Single-Supply Twin-T Notch Filter
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
35
IMPORTANT NOTICE
Texas Instruments and its subsidiaries (TI) reserve the right to make changes to their products or to discontinue
any product or service without notice, and advise customers to obtain the latest version of relevant information
to verify, before placing orders, that information being relied on is current and complete. All products are sold
subject to the terms and conditions of sale supplied at the time of order acknowledgement, including those
pertaining to warranty, patent infringement, and limitation of liability.
TI warrants performance of its semiconductor products to the specifications applicable at the time of sale in
accordance with TI’s standard warranty. Testing and other quality control techniques are utilized to the extent
TI deems necessary to support this warranty. Specific testing of all parameters of each device is not necessarily
performed, except those mandated by government requirements.
CERTAIN APPLICATIONS USING SEMICONDUCTOR PRODUCTS MAY INVOLVE POTENTIAL RISKS OF
DEATH, PERSONAL INJURY, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE (“CRITICAL
APPLICATIONS”). TI SEMICONDUCTOR PRODUCTS ARE NOT DESIGNED, AUTHORIZED, OR
WARRANTED TO BE SUITABLE FOR USE IN LIFE-SUPPORT DEVICES OR SYSTEMS OR OTHER
CRITICAL APPLICATIONS. INCLUSION OF TI PRODUCTS IN SUCH APPLICATIONS IS UNDERSTOOD TO
BE FULLY AT THE CUSTOMER’S RISK.
In order to minimize risks associated with the customer’s applications, adequate design and operating
safeguards must be provided by the customer to minimize inherent or procedural hazards.
TI assumes no liability for applications assistance or customer product design. TI does not warrant or represent
that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other
intellectual property right of TI covering or relating to any combination, machine, or process in which such
semiconductor products or services might be or are used. TI’s publication of information regarding any third
party’s products or services does not constitute TI’s approval, warranty or endorsement thereof.
Copyright  1998, Texas Instruments Incorporated