TI MC79L12ACD

 SLVS011D − OCTOBER 1982 − REVISED AUGUST 2003
D
D
D
D
D
D
D
D PACKAGE
(TOP VIEW)
3-Terminal Regulators
Output Current Up To 100 mA
No External Components Required
Internal Thermal-Overload Protection
Internal Short-Circuit Current Limiting
Direct Replacement for Industry-Standard
MC79L00 Series
Available in 5% or 10% Selections
OUTPUT
INPUT†
INPUT†
NC
1
8
2
7
3
6
4
5
NC
INPUT†
INPUT†
COMMON
† Internally connected
NC − No internal connection
description/ordering information
LP PACKAGE
(TOP VIEW)
This
series
of
fixed
negative-voltage
OUTPUT
integrated-circuit voltage regulators is designed
INPUT
for a wide range of applications. These include
COMMON
on-card regulation for elimination of noise and
distribution problems associated with single-point
regulation. In addition, they can be used to control series pass elements to make high-current voltage-regulator
circuits. One of these regulators can deliver up to 100 mA of output current. The internal current-limiting and
thermal-shutdown features essentially make the regulators immune to overload. When used as a replacement
for a Zener-diode and resistor combination, these devices can provide an effective improvement in output
impedance of two orders of magnitude, with lower bias current.
ORDERING INFORMATION
TJ
OUTPUT
VOLTAGE
TOLERANCE
NOMINAL
OUTPUT
VOLTAGE
(V)
PACKAGE†
SOIC (D)
−5
TO-226 / TO-92 (LP)
5%
0°C
0
C to 125
125°C
C
SOIC (D)
−12
TO-226 / TO-92 (LP)
−15
10%
−12
TO-226 / TO-92 (LP)
TO-226 / TO-92 (LP)
ORDERABLE
PART NUMBER
Tube of 75
MC79L05ACD
Reel of 2500
MC79L05ACDR
Bulk of 1000
MC79L05ACLP
Reel of 2000
MC79L05ACLPR
Tube of 75
MC79L12ACD
Reel of 2500
MC79L12ACDR
Bulk of 1000
MC79L12ACLP
Reel of 2000
MC79L12ACLPR
Bulk of 1000
MC79L15ACLP
Ammo of 2000
MC79L15ACLPM
Reel of 2000
MC79L15ACLPR
Bulk of 1000
MC79L12CLP
TOP-SIDE
MARKING
79L05A
79L05AC
79L12A
79L12AC
79L15AC
79L12C
−15
SOIC (D)
Tube of 75
MC79L15CD
79L15C
† Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines are available at
www.ti.com/sc/package.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
Copyright  2003, Texas Instruments Incorporated
! "#$ %!&
% "! "! '! ! !( !
%% )*& % "!+ %! !!$* $%!
!+ $$ "!!&
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
1
SLVS011D − OCTOBER 1982 − REVISED AUGUST 2003
equivalent schematic
COMMON
OUTPUT
INPUT
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)†
Input voltage: MC79L05 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −30 V
MC79L12, MC79L15 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −35 V
Package thermal impedance, θJA (see Notes 1 and 2): D package . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97°C/W
LP package . . . . . . . . . . . . . . . . . . . . . . . . . . 140°C/W
Operating free-air, case, or virtual junction temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150°C
Lead temperature 1.6 mm (1/16 inch) from case for 10 seconds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 260°C
Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −65°C to 150°C
† Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied.
Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
NOTES: 1. Maximum power dissipation is a function of TJ(max), θJA, and TA. The maximum allowable power dissipation at any allowable ambient
temperature is PD = (TJ(max) − TA)/θJA. Operating at the absolute maximum TJ of 150°C can affect reliability.
2. The package thermal impedance is calculated in accordance with JESD 51-7.
recommended operating conditions
VI
IO
TJ
2
Input voltage
MIN
MAX
MC79L05
−7
−20
MC79L12
−14.5
−27
MC79L15
−17.5
−30
Output current
Operating virtual junction temperature
0
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
UNIT
V
100
mA
125
°C
SLVS011D − OCTOBER 1982 − REVISED AUGUST 2003
electrical characteristics at specified virtual junction temperature, VI = −10 V, IO = 40 mA (unless
otherwise noted)
PARAMETER
Output voltage‡
Input regulation
Ripple rejection
Output regulation
VI = −7 V to −20 V,
IO = 1 mA to 40 mA
VI = −10 V, IO = 1 mA to 70 mA
VI = −7 V to −20 V
VI = −8 V to −20 V
Output noise voltage
Dropout voltage
IO = 40 mA
Bias current
VI = −8 V to −20 V
IO = 1 mA to 40 mA
MC79L05AC
TJ
MIN
TYP
MAX
MIN
TYP
MAX
25°C
−4.6
−5
−5.4
−4.8
−5
−5.2
0°C to 125°C
−4.5
−5.5
−4.75
−5.25
0°C to 125°C
−4.5
−5.5
−4.75
−5.25
25°C
VI = −8 V to −18 V, f = 120 Hz
IO = 1 mA to 100 mA
IO = 1 mA to 40 mA
f = 10 Hz to 100 kHz
Bias current change
MC79L05C
TEST CONDITIONS†
25°C
40
200
150
150
100
49
25°C
25°C
40
25°C
1.7
41
49
V
mV
dB
60
60
30
30
mV
µV
40
1.7
V
25°C
6
6
125°C
5.5
5.5
1.5
1.5
0.2
0.1
0°C to 125°C
UNIT
mA
mA
† All characteristics are measured with a 0.33-µF capacitor across the input and a 0.1-µF capacitor across the output. Pulse-testing techniques are
used to maintain the junction temperature as close to the ambient temperature as possible. Thermal effects must be taken into account separately.
‡ This specification applies only for dc power dissipation permitted by absolute maximum ratings.
electrical characteristics at specified virtual junction temperature, VI = −19 V, IO = 40 mA (unless
otherwise noted)
PARAMETER
Output voltage‡
Input regulation
Ripple rejection
Output regulation
VI = −14.5 V to −27 V,
IO = 1 mA to 40 mA
VI = −19 V, IO = 1 mA to 70 mA
VI = −14.5 V to −27 V
VI = −16 V to −27 V
Output noise voltage
Dropout voltage
IO = 40 mA
Bias current
VI = −16 V to −27 V
IO = 1 mA to 40 mA
MC79L12AC
TJ
MIN
TYP
MAX
MIN
TYP
MAX
25°C
−11.1
−12
−12.9
−11.5
−12
−12.5
0°C to 125°C
−10.8
−13.2
−11.4
−12.6
0°C to 125°C
−10.8
−13.2
−11.4
−12.6
25°C
VI = −15 V to −25 V, f = 120 Hz
IO = 1 mA to 100 mA
IO = 1 mA to 40 mA
f = 10 Hz to 100 kHz
Bias current change
MC79L12C
TEST CONDITIONS†
25°C
36
250
250
200
200
42
25°C
37
42
UNIT
V
mV
dB
100
100
50
50
mV
25°C
80
80
µV
25°C
1.7
1.7
V
25°C
6.5
6.5
125°C
6
6
1.5
1.5
0.2
0.1
0°C to 125°C
mA
mA
† All characteristics are measured with a 0.33-µF capacitor across the input and a 0.1-µF capacitor across the output. Pulse-testing techniques are
used to maintain the junction temperature as close to the ambient temperature as possible. Thermal effects must be taken into account separately.
‡ This specification applies only for dc power dissipation permitted by absolute maximum ratings.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
3
SLVS011D − OCTOBER 1982 − REVISED AUGUST 2003
electrical characteristics at specified virtual junction temperature, VI = −23 V, IO = 40 mA (unless
otherwise noted)
PARAMETER
Output voltage‡
Input regulation
Ripple rejection
Output regulation
VI = −17.5 V to −30 V,
IO = 1 mA to 40 mA
VI = −23 V, IO = 1 mA to 70 mA
VI = −17.5 V to −30 V
VI = −17.5 V to −30 V
VI = −18.5 V to −28.5 V, f = 120 Hz
IO = 1 mA to 100 mA
Output noise voltage
IO = 1 mA to 40 mA
f = 10 Hz to 100 kHz
Dropout voltage
IO = 40 mA
Bias current
Bias current change
MC79L15C
TEST CONDITIONS†
VI = −20 V to −30 V
IO = 1 mA to 40 mA
MC79L15AC
TJ
MIN
TYP
MAX
MIN
TYP
MAX
25°C
−13.8
−15
−16.2
−14.4
−15
−15.6
0°C to 125°C
−13.5
−16.5
−14.25
−15.75
0°C to 125°C
−13.5
−16.5
−14.25
−15.75
25°C
25°C
33
300
300
250
250
39
25°C
25°C
90
25°C
1.7
34
39
V
mV
dB
150
150
75
75
mV
µV
90
1.7
V
25°C
6.5
6.5
125°C
6
6
1.5
1.5
0.2
0.1
0°C to 125°C
UNIT
mA
mA
† All characteristics are measured with a 0.33-µF capacitor across the input and a 0.1-µF capacitor across the output. Pulse-testing techniques are
used to maintain the junction temperature as close to the ambient temperature as possible. Thermal effects must be taken into account separately.
‡ This specification applies only for dc power dissipation permitted by absolute maximum ratings.
4
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
PACKAGE OPTION ADDENDUM
www.ti.com
23-Apr-2007
PACKAGING INFORMATION
Orderable Device
Status (1)
Package
Type
Package
Drawing
Pins Package Eco Plan (2)
Qty
MC79L05ACD
ACTIVE
SOIC
D
8
75
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
MC79L05ACDE4
ACTIVE
SOIC
D
8
75
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
MC79L05ACDG4
ACTIVE
SOIC
D
8
75
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
MC79L05ACDR
ACTIVE
SOIC
D
8
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
MC79L05ACDRE4
ACTIVE
SOIC
D
8
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
MC79L05ACDRG4
ACTIVE
SOIC
D
8
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
MC79L05ACLP
ACTIVE
TO-92
LP
3
1000
Pb-Free
(RoHS)
CU SN
N / A for Pkg Type
MC79L05ACLPE3
ACTIVE
TO-92
LP
3
1000
Pb-Free
(RoHS)
CU SN
N / A for Pkg Type
MC79L05ACLPM
ACTIVE
TO-92
LP
3
2000
Pb-Free
(RoHS)
CU SN
N / A for Pkg Type
MC79L05ACLPME3
ACTIVE
TO-92
LP
3
2000
Pb-Free
(RoHS)
CU SN
N / A for Pkg Type
MC79L05ACLPR
ACTIVE
TO-92
LP
3
2000
Pb-Free
(RoHS)
CU SN
N / A for Pkg Type
MC79L05ACLPRE3
ACTIVE
TO-92
LP
3
2000
Pb-Free
(RoHS)
CU SN
N / A for Pkg Type
MC79L05AILP
OBSOLETE
TO-92
LP
3
TBD
Call TI
Call TI
MC79L05CD
OBSOLETE
SOIC
D
8
TBD
Call TI
Call TI
MC79L05CDR
OBSOLETE
SOIC
D
8
TBD
Call TI
Call TI
MC79L05CLP
OBSOLETE
TO-92
LP
3
TBD
Call TI
Call TI
MC79L12ACD
ACTIVE
SOIC
D
8
75
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
MC79L12ACDE4
ACTIVE
SOIC
D
8
75
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
MC79L12ACDG4
ACTIVE
SOIC
D
8
75
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
MC79L12ACDR
ACTIVE
SOIC
D
8
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
MC79L12ACDRE4
ACTIVE
SOIC
D
8
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
MC79L12ACDRG4
ACTIVE
SOIC
D
8
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
MC79L12ACLP
ACTIVE
TO-92
LP
3
1000
Pb-Free
(RoHS)
CU SN
N / A for Pkg Type
MC79L12ACLPE3
ACTIVE
TO-92
LP
3
1000
Pb-Free
(RoHS)
CU SN
N / A for Pkg Type
MC79L12ACLPR
ACTIVE
TO-92
LP
3
2000
Pb-Free
(RoHS)
CU SN
N / A for Pkg Type
MC79L12ACLPRE3
ACTIVE
TO-92
LP
3
2000
Pb-Free
(RoHS)
CU SN
N / A for Pkg Type
MC79L12CD
OBSOLETE
SOIC
D
8
TBD
Call TI
Call TI
Addendum-Page 1
Lead/Ball Finish
MSL Peak Temp (3)
PACKAGE OPTION ADDENDUM
www.ti.com
23-Apr-2007
Orderable Device
Status (1)
Package
Type
Package
Drawing
Pins Package Eco Plan (2)
Qty
MC79L12CLP
ACTIVE
TO-92
LP
3
1000
Pb-Free
(RoHS)
CU SN
N / A for Pkg Type
MC79L12CLPE3
ACTIVE
TO-92
LP
3
1000
Pb-Free
(RoHS)
CU SN
N / A for Pkg Type
Lead/Ball Finish
MSL Peak Temp (3)
MC79L15ACD
OBSOLETE
SOIC
D
8
TBD
Call TI
Call TI
MC79L15ACLP
ACTIVE
TO-92
LP
3
1000
Pb-Free
(RoHS)
CU SN
N / A for Pkg Type
MC79L15ACLPE3
ACTIVE
TO-92
LP
3
1000
Pb-Free
(RoHS)
CU SN
N / A for Pkg Type
MC79L15ACLPM
ACTIVE
TO-92
LP
3
2000
Pb-Free
(RoHS)
CU SN
N / A for Pkg Type
MC79L15ACLPME3
ACTIVE
TO-92
LP
3
2000
Pb-Free
(RoHS)
CU SN
N / A for Pkg Type
MC79L15ACLPR
ACTIVE
TO-92
LP
3
2000
Pb-Free
(RoHS)
CU SN
N / A for Pkg Type
MC79L15ACLPRE3
ACTIVE
TO-92
LP
3
2000
Pb-Free
(RoHS)
CU SN
N / A for Pkg Type
MC79L15CD
ACTIVE
SOIC
D
8
75
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
MC79L15CDE4
ACTIVE
SOIC
D
8
75
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
MC79L15CDG4
ACTIVE
SOIC
D
8
75
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
MC79L15CLP
OBSOLETE
TO-92
LP
3
TBD
Call TI
Call TI
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check
http://www.ti.com/productcontent for the latest availability information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and
package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS
compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame
retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder
temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
Addendum-Page 2
PACKAGE OPTION ADDENDUM
www.ti.com
23-Apr-2007
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.
Addendum-Page 3
PACKAGE MATERIALS INFORMATION
www.ti.com
12-Jan-2008
TAPE AND REEL BOX INFORMATION
Device
Package Pins
Site
Reel
Diameter
(mm)
Reel
Width
(mm)
A0 (mm)
B0 (mm)
K0 (mm)
P1
(mm)
W
Pin1
(mm) Quadrant
MC79L05ACDR
D
8
SITE 27
330
12
6.4
5.2
2.1
8
12
Q1
MC79L12ACDR
D
8
SITE 27
330
12
6.4
5.2
2.1
8
12
Q1
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
12-Jan-2008
Device
Package
Pins
Site
Length (mm)
Width (mm)
Height (mm)
MC79L05ACDR
D
8
SITE 27
342.9
338.1
20.64
MC79L12ACDR
D
8
SITE 27
342.9
338.1
20.64
Pack Materials-Page 2
MECHANICAL DATA
MSOT002A – OCTOBER 1994 – REVISED NOVEMBER 2001
LP (O-PBCY-W3)
PLASTIC CYLINDRICAL PACKAGE
0.205 (5,21)
0.175 (4,44)
0.165 (4,19)
0.125 (3,17)
DIA
0.210 (5,34)
0.170 (4,32)
Seating
Plane
0.157 (4,00) MAX
0.050 (1,27)
C
0.500 (12,70) MIN
0.104 (2,65)
FORMED LEAD OPTION
0.022 (0,56)
0.016 (0,41)
0.016 (0,41)
0.014 (0,35)
STRAIGHT LEAD OPTION
D
0.135 (3,43) MIN
0.105 (2,67)
0.095 (2,41)
0.055 (1,40)
0.045 (1,14)
1
2
3
0.105 (2,67)
0.080 (2,03)
0.105 (2,67)
0.080 (2,03)
4040001-2 /C 10/01
NOTES: A. All linear dimensions are in inches (millimeters).
B. This drawing is subject to change without notice.
C. Lead dimensions are not controlled within this area
D. FAlls within JEDEC TO -226 Variation AA (TO-226 replaces TO-92)
E. Shipping Method:
Straight lead option available in bulk pack only.
Formed lead option available in tape & reel or ammo pack.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
1
MECHANICAL DATA
MSOT002A – OCTOBER 1994 – REVISED NOVEMBER 2001
LP (O-PBCY-W3)
PLASTIC CYLINDRICAL PACKAGE
0.539 (13,70)
0.460 (11,70)
1.260 (32,00)
0.905 (23,00)
0.650 (16,50)
0.610 (15,50)
0.020 (0,50) MIN
0.098 (2,50)
0.384 (9,75)
0.335 (8,50)
0.748 (19,00)
0.217 (5,50)
0.433 (11,00)
0.335 (8,50)
0.748 (19,00)
0.689 (17,50)
0.114 (2,90)
0.094 (2,40)
0.114 (2,90)
0.094 (2,40)
0.169 (4,30)
0.146 (3,70)
DIA
0.266 (6,75)
0.234 (5,95)
0.512 (13,00)
0.488 (12,40)
TAPE & REEL
4040001-3 /C 10/01
NOTES: A. All linear dimensions are in inches (millimeters).
B. This drawing is subject to change without notice.
C. Tape and Reel information for the Format Lead Option package.
2
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Amplifiers
Data Converters
DSP
Clocks and Timers
Interface
Logic
Power Mgmt
Microcontrollers
RFID
RF/IF and ZigBee® Solutions
amplifier.ti.com
dataconverter.ti.com
dsp.ti.com
www.ti.com/clocks
interface.ti.com
logic.ti.com
power.ti.com
microcontroller.ti.com
www.ti-rfid.com
www.ti.com/lprf
Applications
Audio
Automotive
Broadband
Digital Control
Medical
Military
Optical Networking
Security
Telephony
Video & Imaging
Wireless
www.ti.com/audio
www.ti.com/automotive
www.ti.com/broadband
www.ti.com/digitalcontrol
www.ti.com/medical
www.ti.com/military
www.ti.com/opticalnetwork
www.ti.com/security
www.ti.com/telephony
www.ti.com/video
www.ti.com/wireless
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright 2008, Texas Instruments Incorporated