Ordering number : ENA1394 Bi-CMOS IC LV5052V Built-in 2-channels DC/DC Converter Controller Overview The LV5052V is a high efficiency DC/DC converter controller with 2-channels IC adopting a synchronous rectifying system. Incorporating numerous functions on a single chip with easy external setting, it can be used for a wide variety of applications. This device is optimal for use in internal power supply systems which are used in electronic devices, LCD-TVs, DVD recorders, etc. Functions • Step-down DC/DC converter controller with 2-channel • Built-in input UVLO circuit, Over current detection function, soft-start/soft-stop function and Start-up delay circuit • Built-in output voltage monitor function (Under voltage protection with power good and timer latch) • 180 degree interleaving operation during 1-phase to 2-phase • Synchronized operation is possible (Master-slave operation is possible when using plural devices) Specifications Absolute Maximum Ratings at Ta = 25°C Parameter Symbol Supply voltage VIN Output peak current IOUT Conditions Mounted on a specified board *1 Ratings Unit 18 V ±1.0 A Allowable power dissipation Pd max 1.0 W Operating temperature Topr -20 to 85 °C Storage temperature Tstg -55 to +150 °C *1: Specified board: 114.3mm × 76.1mm ×1.6mm, glass epoxy board. Continued on next page. Any and all SANYO Semiconductor Co.,Ltd. products described or contained herein are, with regard to "standard application", intended for the use as general electronics equipment (home appliances, AV equipment, communication device, office equipment, industrial equipment etc.). The products mentioned herein shall not be intended for use for any "special application" (medical equipment whose purpose is to sustain life, aerospace instrument, nuclear control device, burning appliances, transportation machine, traffic signal system, safety equipment etc.) that shall require extremely high level of reliability and can directly threaten human lives in case of failure or malfunction of the product or may cause harm to human bodies, nor shall they grant any guarantee thereof. If you should intend to use our products for applications outside the standard applications of our customer who is considering such use and/or outside the scope of our intended standard applications, please consult with us prior to the intended use. If there is no consultation or inquiry before the intended use, our customer shall be solely responsible for the use. Specifications of any and all SANYO Semiconductor Co.,Ltd. products described or contained herein stipulate the performance, characteristics, and functions of the described products in the independent state, and are not guarantees of the performance, characteristics, and functions of the described products as mounted in the customer' s products or equipment. To verify symptoms and states that cannot be evaluated in an independent device, the customer should always evaluate and test devices mounted in the customer' s products or equipment. 12809 MS 20081209-S00004 No.A1394-1/9 LV5052V Continued from preceding page. Parameter Symbol Conditions Ratings Unit Allowable terminal voltage *2 1 HDRV1,2, CBOOT1,2 25 V 2 Between HDRV1,2, CBOOT1,2 and SW1,2 6.5 V 3 VIN, ILIM1,2, RSNS1,2, SW1,2, PGOOD1,2 18 V 4 VLIN5, VDD, LDRV1,2 5 COMP1,2, FB1,2, SS1,2, UV_DELAY,TD1,2, CT, CLKO 6.5 V VLIN5+0.3 V *2: The Allowable Terminal Voltage, the SGND+PGND pin becomes a standard except for No.2 of the allowable terminal voltage about No.2 of the allowable terminal voltage, the SW pin becomes a standard. Recommended Operating Condition at Ta = 25°C Parameter Supply voltage Symbol Conditions Ratings VIN Unit 9.4 to 16 V Electrical Characteristics at Ta = 25°C, VIN=12V, Unless especially specified. Parameter Symbol Ratings Conditions min typ Unit max System Reference voltage for comparing VREF Supply current 1 ICC1 TD1,2 = 5V (Except for the Ciss charge) Supply current 2 ICC2 TD1,2 = 0V 5V supply voltage VLIN5 IVIN5 = 0 to 10mA Over-current sense comparator offset VCLOS Over-current sense reference current ICL 0.838 0.840 0.848 4 6 8 mA 0.8 1.4 2.0 mA 5.10 5.30 5.50 -5 VIN = 10 to 14V V V +5 mV µA 75 85 95 -7.0 source Soft start source current ISSSC TD = 5V -1.8 -3.5 Soft start sink current ISSSK TD = 0V 0.2 1.0 Soft start clamp voltage VSST0 UV_DELAY source current ISCUVD UV_DELAY = 2V UV_DELAY sink current ISKUVD UV_DELAY = 2V UV_DELAY threshold voltage VUVD UV_DELAY operating voltage VUVP VUVP detection hysteresis ∆VUVP Over-voltage detection VOVP Output discharge transistor ON resistance VSWON 100% at VFBx = VREF 1.2 1.6 2.0 V -4.3 -8.6 -17.2 µA 0.2 1.0 1.5 2.4 3.5 mA V 77 82 87 % 4 100% at VFBx = VREF µA mA % 113 118 123 % 5 10 20 Ω 10 µA Output part CBOOT leakage current ICBOOT VCBOOT = VSW + 6.5V HDRVx LDRVx source current ISCDRV 1.0 HDRVx LDRVx sink current ISKDRV 1.0 HDRVx lower ON resistance RHDRV LDRVx lower ON resistance Synchronous ON prevention dead time 1 Synchronous ON prevention dead time 2 A A Ω IOUT = 500mA 1.5 2.5 RLDRV IOUT = 500mA 1.5 2.5 Tdead1 LDRV OFF→HDRV ON 50 ns Tdead2 HDRV OFF→LDRV ON 120 ns Oscillation frequency fosc CT=130pF Oscillation frequency range foscop Maximum ON duty DON max Ω Oscillator 280 330 250 CT=130pF 380 kHz 1100 kHz 82 % Minimum ON time TON min CT=130pF 100 Upper-side voltage saw- tooth wave VsawH fOSC=300kHz 2.75 3.2 V Lower-side voltage saw-tooth wave VsawL fOSC=300kHz 1 1.2 V ON time difference between CH1 to CH2 ∆Tdead 5 ns % Continued on next page. No.A1394-2/9 LV5052V Continued from preceding page. Parameter Symbol Ratings Conditions min typ Unit max Error Amplifier Error amplifier input current IFB COMP pin source current ICOMPSC COMP pin sink current ICOMPSK Error amplifier gm gm Current detection amplifier gain GISNS -200 -100 200 nA -100 -18 µA µA 18 100 500 700 900 5 6.4 7.8 0.5 1.0 umho Logic output Power Good low level source current IpwrgdL VPGOOD = 0.4V Power Good high level leakage current IpwrgdH VPGOOD = 12V TP pin threshold voltage VONTD When the voltage of the TD pin rises TP pin high impedance voltage VTDH When VIN and VLIN5 pins are set to open 4.5 5.2 5.5 V TD pin charge source current ITDSC -1.8 -3.5 -7.0 µA TD pin discharge sink current ITDSK 0.2 1.0 CLKO high level voltage VCLKOH ICLKO = 1mA CLKO low level voltage VCLKOL ICLKO = 1mA 1.5 2.6 mA 10 µA 3.5 V mA 0.7V5LIN V 0.3V5LIN V Protection function VIN UVLO Release voltage VUVLO UVLO Hysteresis ∆VUVLO 3.5 4.1 0.4 4.3 mA µA No.A1394-3/9 LV5052V Package Dimensions unit : mm (typ) 3191B Pd max - Ta Allowable power dissipation, Pd max -- mW 1200 9.75 0.5 5.6 7.6 16 30 1 15 0.65 0.15 0.22 1.5max (1.3) (0.33) Specified board: 114.3×76.1×1.6mm3 glass epoxy board. 1000 950 800 600 494 400 200 0 -20 0 20 40 60 80 85 100 0.1 Ambient temperature, Ta -- °C SANYO : SSOP30(275mil) PGND LDRV2 HDRV2 SW2 CBOOT2 SGND COMP2 FB2 RSNS2 ILIM2 TD2 SS2 PGOOD2 CT CLKO Pin Assignment 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 VDD LDRV1 HDRV1 SW1 CBOOT1 VLIN5 COMP1 FB1 RSNS1 ILIM1 TD1 SS1 PGOOD1 UV_DELAY VIN LV5052V Top view No.A1394-4/9 LV5052V Block Diagram Voltage and current generator BG BG reference IREF VIN VIN POR 9.0V /8.0V Current bias Input Power Supply VLIN5 5.3V 5V REG (always ON) Vref VLIN5 Internal Bias Vref 0.84V 4.5V /4.0V Typ 85µA ILIM Comp COMP1 ILIM1 VIN SENSE Amp CH1 output RSNS1 PWM comp Error Amp FB1 0.82Vref UV1 1.18Vref OV1 Shifter & latch PWM logic SKIP control Vref SS1 SW1 Corrective ramp SD SS1EN D SD HDRV1 S Q 1.6V 3.5µA CBOOT1 R Q Shoot through protection sequencer CH1 output VDD LDRV1 0 deg Active discharge Rdson = 15Ω 3.5µA TD1 Typ 85µA CONT1 POR 2.6V ILIM Comp COMP2 ILIM2 VIN SENSE Amp CH2 output RSNS2 PWM comp Error Amp FB2 0.82Vref UV2 1.18Vref OV2 Shifter & latch PWM logic SKIP control SW2 1.6V SS2 Corrective ramp SD SS2EN D SD HDRV2 S Q Vref 3.5µA CBOOT2 R Q Shoot through protection sequencer LDRV2 180 deg PGND Active discharge Rdson = 15Ω 3.5µA TD2 POR CH2 output CONT2 2.6V CONT1 CONT2 POR OV1 9µA OV2 1µs delay R Q 0V S Q UV1 UV2 SS1EN D SS2EN D PGOOD1 PGOOD2 2.6V UV_DELAY UV timeout 0 180 deg deg OSC 300kHz CT CLKO SGND Sync. pulse out 5V 0V No.A1394-5/9 LV5052V Pin Functions Pin No. 1 Pin name VDD Description Power supply pin for the gate drive of an external lower-side MOS-FET. This pin is connected to the VLIN5 pin through a filter. 2 LDRV The gate drive pin of an external lower-side MOS-FET of channel 1. This pin has the signal input part for prevention of short-through of both the upper and lower MOS-FETs. When the voltage of this pin becomes less than 1V, the HDRV pin is turned on. 3 HDRV1 The gate drive pin for an external upper side MOS-FET of channel 1. 4 SW1 This pin is connected with the switching node of channel 1. A source of an external upper side MOSFET and a drain of an external lower side MOS-FET are connected with this pin. This pin becomes the return current path of the HDRV pin. This pin is connected with a transistor drain of the discharge MOS-FET for SOFT STOP in the IC (typical 30Ω). Also, this pin has the signal output part for the short through prevention of both the upper and lower MOS-FETs. When this terminal voltage becomes 1V or less for PGND, the LDRV pin is turned on. 5 CBOOT1 The bootstrap capacity connection pin of channel 1. The gate drive power of upper MOSFET is provided by this pin. This pin is connected to the VDD pin through a diode and is connected to the SW pin through the bootstrap capacity. 6 VLIN5 The output pin of an internal regulator of 5V. the current is provided by the VIN pin. Also, power supply of the control circuit in the IC is provided by this pin. Connect an output capacitor of 4.7µF between this pin and SGND. A regulator of 5V operates, even if the IC is in the standby state. This pin is monitored by an UVLO function and the IC starts by the voltage of 4.5V or more (the IC is off by the voltage of 4.0V or less.) 7 COMP1 The phase compensation pin of channel 1. The output of an internal transformer conductance amplifier is connected. Connect an external phase compensation circuit between this pin and SGND. 8 FB1 Feed back input pin of channel 1. The minus terminal (-) of the trans conductance amplifier is connected. The voltage generated when the output voltage was divided by a resistor is input into this pin. The converter operates so that this pin becomes an internal reference voltage (VREF=0.8V). Also, this pin is monitored by the comparators UVP and OVP. When the voltage of this pin becomes less than 82% of the set voltage, the PGOOD pin is low level. A timer of the UV_DELAY function operates. Also, when the voltage of this pin becomes more than 117% of the set voltage, the IC latches off. 9 RSNS1 Channel 1 side input pin of the over current detection comparator / the current detection amplifier. To detect resistance, this pin is connected to the under side of a resistor for the current detection between the VIN pin and the DRAIN of the upper MOS-FET. Also, to use the ON resistance of MOS-FET for the current detection, connect this pin to the SOURCE of the upper MOS-FET. To prevent the common impedance of main current to the detection-voltage, this pin is connected by independent wiring. 10 ILIM The pin to set the trip point for over current detection of channel 1. Since the SINK current source of 85µA (ILIM) is connected in the IC, the over-current detection voltage (ILIM × RLIM) is generated by connecting a resistor RLIM between this pin and the VIN pin. The over-current is detected by comparing the voltage between the VIN pin and the ILIM pin to the current detection resistance RSNS or both end voltage of the upper MOSFET. 11 TD Start-up delay pin of channel 1. The time until the IC starts after releasing POR is set by connecting a capacitor between this pin and SGND. After releasing POR, an external capacitor is charged up by the constant current source of 3.5µA in the IC. When this terminal voltage becomes 2.6V or more, The IC starts. Also, when this terminal voltage becomes 2.6V or less, The IC becomes the standby state. If external capacitor is not connected, the IC instantly starts after releasing POR. 12 SS1 The pin to connect a capacitor for soft start of channel 1. After releasing POR, when the voltage of the TD pin becomes 2.6V or more, the SS1 pin is charged by an internal constant current source of 3.5µA. Since this pin is connected to the positive (+) input of the transformer conductance amplifier, the ramp-up wave form of the SS pin becomes the ramp-up wave form of the output. During POR operations and after the UV_DELAY time-out, the SS1 pin is discharged 13 PGOOD The power good pin of channel 1. The open drain MOS-FET of the withstand of 28V is connected in the IC. When the output voltage of channel 1 is less than -13% for the setup voltage, the low level is output. This pin has hysteresis of about (VREF × 4.0%). 14 UV_DELAY Common UVP DELAY pin to channel 1 and channel 2. By connecting a capacitor between this pin and SGND, the time until the IC latches off after detecting the UVP state can be set. Also, after channel 1 or channel 2 terminated the soft-start function, when the output voltage becomes 82% or less for the setup voltage, an external capacitor is charged by the constant current source of 8.6µA in the IC. When this terminal voltage becomes 2.6V or more, the IC is latched off. If an external capacitor is not connected, the IC is instantly latched off after detecting the UVP state. Also, when this pin is shorted to GND, the UV_DELAY function is not operated. Continued on next page. No.A1394-6/9 LV5052V Continued from preceding page. Pin No. Pin name 15 VIN 16 CLKO Description Power supply pin of the IC. This pin is observed by the UVLO function and IC starts by 9.0V or more. (After starts, stop by 8.0V or less. ) The clock output pin. The clock that synchronized to the oscillation waveform of the CT pin is output. To synchronize two or more LV5052Vs, the CLKO pin of the device that becomes a master is connected to the CT pin of the device that becomes a slave. When two or more the devices are synchronized and the start-up timing is changed by using the TD pin between each device, the earliest start-up device is determined as the master. 17 CT The pin to connect an external capacitor for the oscillator. Connect a capacitor between this pin and SGND. When a capacitor of 130pF is connected between this pin and GND, the oscillation frequency can be set up by 330kHz. Also, this pin is applied by an external clock signal. The PWM operation is performed by the frequency of applied clock signal. When an external clock signal is applied, the rectangular wave of 0V in low level and from 0V / 3.3V to 5V in high level is applied. The rectangular wave source needs the fan-out of 1mA or more. 18 PGOOD2 The power good pin of channel 2. 19 SS2 The pin to connect a capacitor for soft start of channel 2. 20 TD2 Start-up delay pin of channel 2. 21 ILIM2 The pin to set the trip point for over current detection of channel 2. 22 RSNS2 Channel 2 side input pin of the over current detection comparator / the current detection amplifier. 23 FB2 Feed back input pin of channel 2. 24 COMP2 The phase compensation pin of channel 2. 25 SGND The system ground of the IC. The reference voltage is generated based on this pin. 26 CBOOT2 The bootstrap capacity connection pin of channel 2. 27 SW2 This pin is connected with the switching node of channel 2. 28 HDRV2 The gate drive pin for an external upper side MOS-FET of channel 2. 29 LDRV2 The gate drive pin of an external lower-side MOS-FET of channel 2. 30 PGND Power ground pin. This pin becomes the return current path of the LDRV pin. This pin is connected to the power supply system ground. No.A1394-7/9 LV5052V Start-up Sequence Each signal control timing at power supply ON is as below. VIN=12V 9V typ VIN UVLO release * VLIN5=5V 4.5V typ VLIN5 2.4V typ TD=5V TD SS=1.6V 0.8V SS VOUT=Vout × 100% Vout × 82% VOUT PGOOD * Starts charging the TD at the trigger point of either VIN > 9V(typ) or VLIN5 > 4.5V(typ), whichever is later. Protection Operate Sequence (1) Latch-off release by UVLO The signal control timing diagram for resetting the latch-off condition using UVLO is shown below. VIN=12V 9V typ VIN 8V typ Restart VLIN5=5V VLIN5 TD discharge start TD=5V 2.4V typ TD SS=1.6V 0.8V SS Vout × 118% VOUT Vout × 82% VOUT=Vout × 100% Vout × 82% OVP PGOOD (2) Latch off release by TD The signal control timing diagram for resetting the latch-off condition using UVLO is shown below. VIN=12V VIN VLIN5=5V VLIN5 TD discharge start TD=5V 2.4V typ TD SS=1.6V 0.8V SS Vout × 118% VOUT Vout × 82% OVP VOUT=Vout × 100% Vout × 82% PGOOD No.A1394-8/9 LV5052V Synchronized operation A recommended circuit for synchronizing the LV5052V is shown below. Master Slave VIN VIN VIN (typ 12V) 10kΩ CLKO CT CT 130pF VIN 10kΩ CT SANYO Semiconductor Co.,Ltd. assumes no responsibility for equipment failures that result from using products at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges, or other parameters) listed in products specifications of any and all SANYO Semiconductor Co.,Ltd. products described or contained herein. SANYO Semiconductor Co.,Ltd. strives to supply high-quality high-reliability products, however, any and all semiconductor products fail or malfunction with some probability. It is possible that these probabilistic failures or malfunction could give rise to accidents or events that could endanger human lives, trouble that could give rise to smoke or fire, or accidents that could cause damage to other property. When designing equipment, adopt safety measures so that these kinds of accidents or events cannot occur. Such measures include but are not limited to protective circuits and error prevention circuits for safe design, redundant design, and structural design. In the event that any or all SANYO Semiconductor Co.,Ltd. products described or contained herein are controlled under any of applicable local export control laws and regulations, such products may require the export license from the authorities concerned in accordance with the above law. No part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying and recording, or any information storage or retrieval system, or otherwise, without the prior written consent of SANYO Semiconductor Co.,Ltd. Any and all information described or contained herein are subject to change without notice due to product/technology improvement, etc. When designing equipment, refer to the "Delivery Specification" for the SANYO Semiconductor Co.,Ltd. product that you intend to use. Information (including circuit diagrams and circuit parameters) herein is for example only; it is not guaranteed for volume production. Upon using the technical information or products described herein, neither warranty nor license shall be granted with regard to intellectual property rights or any other rights of SANYO Semiconductor Co.,Ltd. or any third party. SANYO Semiconductor Co.,Ltd. shall not be liable for any claim or suits with regard to a third party's intellctual property rights which has resulted from the use of the technical information and products mentioned above. This catalog provides information as of January, 2009. Specifications and information herein are subject to change without notice. PS No.A1394-9/9