STB11NK40Z, STP11NK40ZFP STP11NK40Z N-channel 400 V, 0.49 Ω, 9 A, TO-220, TO-220FP, D2PAK Zener-protected SuperMESHTM Power MOSFET Features Type VDSS RDS(on) ID Pw STB11NK40Z 400V <0.55Ω 10A 110W STP11NK40Z 400V <0.55Ω 10A 110W 3 3 1 STP11NK40ZFP 400V <0.55Ω 10A 2 1 30W TO-220FP TO-220 ■ Extremely high dv/dt capability ■ 100% avalanche tested 2 3 1 ■ Gate charge minimized ■ Very low intrinsic capacitances ■ Very good manufacturing repeatability D2PAK Applications ■ Figure 1. Switching application Internal schematic diagram Description The SuperMESH™ series is obtained through an extreme optimization of ST’s well established strip-based PowerMESH™ layout. In addition to pushing on-resistance significantly down, special care is taken to ensure a very good dv/dt capability for the most demanding applications. Table 1. Device summary Order code Marking Package Packaging STB11NK40ZT4 B11NK40Z D²PAK Tape and reel STP11NK40Z P11NK40Z TO-220 Tube STP11NK40ZFP P11NK40ZFP TO-220FP Tube April 2009 Doc ID 8936 Rev 7 1/17 www.st.com 17 Contents STB11NK40Z, STP11NK40ZFP, STP11NK40Z Contents 1 Electrical ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 2.1 Electrical characteristics (curves) ............................ 7 3 Test circuits 4 Package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 5 Packaging mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 6 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 2/17 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Doc ID 8936 Rev 7 STB11NK40Z, STP11NK40ZFP, STP11NK40Z 1 Electrical ratings Electrical ratings Table 2. Absolute maximum ratings Value Symbol Parameter Unit TO-220/D²PAK VDS VDGR VGS ID ID TO-220FP Drain-source voltage (VGS = 0) 400 V Drain-gate voltage (RGS = 20KΩ) 400 V Gate-source voltage ± 30 Drain current (continuous) at TC = 25°C Drain current (continuous) at TC=100°C V 9 9(1) A 5.67 5.67(1) A A IDM(2) Drain current (pulsed) 36 36(1) PTOT Total dissipation at TC = 25°C 110 30 W Derating factor 0.88 0.24 W/°C VESD(G-S) Gate source ESD (HBM-C= 100pF, R= 1.5kΩ) 3500 V dv/dt(3) Peak diode recovery voltage slope 4.5 V/ns VISO Insulation withstand voltage (DC) TJ Tstg Operating junction temperature Storage temperature -- 2500 -55 to 150 V °C 1. Limited only by maximum temperature allowed 2. Pulse width limited by safe operating area 3. ISD ≤9A, di/dt ≤200 A/µs, VDD ≤V(BR)DSS, Tj ≤TJMAX. Table 3. Thermal data Value Symbol Rthj-case Parameter Thermal resistance junction-case max Unit TO-220/D²PAK TO-220FP 1.14 4.2 °C/W Rthj-a Thermal resistance junction-ambient max 62.5 °C/W Tl Maximum lead temperature for soldering purpose 300 °C Doc ID 8936 Rev 7 3/17 Electrical ratings Table 4. Symbol 4/17 STB11NK40Z, STP11NK40ZFP, STP11NK40Z Avalanche characteristics Parameter IAR Avalanche current, repetitive or notrepetitive (pulse width limited by Tj max) EAS Single pulse avalanche energy (starting Tj=25°C, Id=Iar, Vdd=50V) Doc ID 8936 Rev 7 Value Unit 9 A 190 mJ STB11NK40Z, STP11NK40ZFP, STP11NK40Z 2 Electrical characteristics Electrical characteristics (TCASE=25°C unless otherwise specified) Table 5. Symbol V(BR)DSS On/off states Parameter Test conditions Drain-source breakdown voltage ID = 1mA, VGS= 0 Min. Typ. Max. Unit 400 V VDS = Max rating, VDS = Max rating @125°C 1 50 µA µA Gate body leakage current (VDS = 0) VGS = ± 20V, VDS = 0 ±10 µA VGS(th) Gate threshold voltage VDS= VGS, ID = 100µA 3.75 4.5 V RDS(on) Static drain-source on resistance VGS= 10V, ID= 4.5A 0.49 0.55 Ω Min. Typ. Max. Unit IDSS Zero gate voltage drain current (VGS = 0) IGSS Table 6. Symbol gfs (1) Ciss Coss Crss Dynamic Parameter Qgs Qgd Test conditions Forward transconductance VDS =15V, ID = 4.5A - 5.8 - S Input capacitance Output capacitance Reverse transfer capacitance VDS =25V, f=1 MHz, VGS=0 - 930 140 30 - pF pF pF VGS=0, VDS =0V to 320V - 78 - pF - 32 6 18.5 - nC nC nC Coss eq(2). Equivalent output capacitance Qg 3 Total gate charge Gate-source charge Gate-drain charge VDD=320V, ID = 9A VGS =10V (see Figure 18) 1. Pulsed: pulse duration=300µs, duty cycle 1.5% 2. Coss eq. is defined as a constant equivalent capacitance giving the same charging time as Coss when VDS inceases from 0 to 80% VDSS Doc ID 8936 Rev 7 5/17 Electrical characteristics STB11NK40Z, STP11NK40ZFP, STP11NK40Z Table 7. Switching times Symbol Parameter td(on) tr td(off) tf tr(Voff) tf tc Table 8. Symbol ISD Test conditions Min. Typ. Max. Unit - 20 20 - ns ns - 40 18 - ns ns - 15 17 30 - ns ns ns Min. Typ. Max Unit VDD=200 V, ID=4.5A, Turn-on delay time Rise time RG=4.7Ω, VGS=10V (see Figure 20) VDD=200V, ID=4.5A, Turn-off delay time Fall time RG=4.7Ω, VGS=10V (see Figure 20) VDD=320V, ID=9A, Off-voltage rise time Fall time Cross-over time RG=4.7Ω, VGS=10V (see Figure 20) Source drain diode Parameter Test conditions Source-drain current - 9 A ISDM(1) Source-drain current (pulsed) - 36 A VSD(2) Forward on voltage ISD=9A, VGS=0 - 1.6 V Reverse recovery time Reverse recovery charge Reverse recovery current ISD=9A, trr Qrr IRRM di/dt = 100A/µs, VDD=45V, Tj=150°C - 225 1.6 14 ns µC A Min. Typ. Max. Unit 30 - - V 1. Pulse width limited by safe operating area 2. Pulsed: pulse duration=300 µs, duty cycle 1.5 % Table 9. Symbol BVGSO Gate-source zener diode Parameter Test conditions Gate-source breakdown voltage Igs=±1mA (open drain) The built-in back-to-back Zener diodes have specifically been designed to enhance not only the device’s ESD capability, but also to make them safely absorb possible voltage transients that may occasionally be applied from gate to source. In this respect the Zener voltage is appropriate to achieve an efficient and cost-effective intervention to protect the device’s integrity. These integrated Zener diodes thus avoid the usage of external components. 6/17 Doc ID 8936 Rev 7 STB11NK40Z, STP11NK40ZFP, STP11NK40Z Electrical characteristics 2.1 Electrical characteristics (curves) Figure 2. Safe operating area for TO-220 D²PAK Figure 3. Thermal impedance for TO-220 D²PAK Figure 4. Safe operating area for TO-220FP Figure 5. Thermal impedance for TO-220FP Figure 6. Output characteristics Figure 7. Transfer characteristics Doc ID 8936 Rev 7 7/17 Electrical characteristics Figure 8. STB11NK40Z, STP11NK40ZFP, STP11NK40Z Transconductance Figure 9. Static drain-source on resistance Figure 10. Gate charge vs gate-source voltage Figure 11. Capacitance variations Figure 12. Normalized gate threshold voltage vs temperature 8/17 Figure 13. Normalized on resistance vs temperature Doc ID 8936 Rev 7 STB11NK40Z, STP11NK40ZFP, STP11NK40Z Figure 14. Source-drain diode forward characteristics Electrical characteristics Figure 15. Normalized BVDSS vs temperature Figure 16. Maximum avalanche energy vs temperature Doc ID 8936 Rev 7 9/17 Test circuits 3 STB11NK40Z, STP11NK40ZFP, STP11NK40Z Test circuits Figure 17. Switching times test circuit for resistive load Figure 18. Gate charge test circuit Figure 19. Test circuit for inductive load Figure 20. Unclamped inductive load test switching and diode recovery times circuit Figure 21. Unclamped inductive waveform 10/17 Figure 22. Switching time waveform Doc ID 8936 Rev 7 STB11NK40Z, STP11NK40ZFP, STP11NK40Z 4 Package mechanical data Package mechanical data In order to meet environmental requirements, ST offers these devices in different grades of ECOPACK® packages, depending on their level of environmental compliance. ECOPACK® specifications, grade definitions and product status are available at: www.st.com. ECOPACK is an ST trademark. Doc ID 8936 Rev 7 11/17 Package mechanical data STB11NK40Z, STP11NK40ZFP, STP11NK40Z D²PAK (TO-263) mechanical data mm inch Dim Min A A1 b b2 c c2 D D1 E E1 e e1 H J1 L L1 L2 R V2 Typ 4.40 0.03 0.70 1.14 0.45 1.23 8.95 7.50 10 8.50 Max Min 4.60 0.23 0.93 1.70 0.60 1.36 9.35 0.173 0.001 0.027 0.045 0.017 0.048 0.352 0.295 0.394 0.334 10.40 2.54 4.88 15 2.49 2.29 1.27 1.30 Max 0.181 0.009 0.037 0.067 0.024 0.053 0.368 0.409 0.1 5.28 15.85 2.69 2.79 1.40 1.75 0.192 0.590 0.099 0.090 0.05 0.051 8° 0° 0.4 0° 0079457_M 12/17 Typ Doc ID 8936 Rev 7 0.208 0.624 0.106 0.110 0.055 0.069 0.016 8° STB11NK40Z, STP11NK40ZFP, STP11NK40Z Package mechanical data TO-220 mechanical data mm inch Dim Min A b b1 c D D1 E e e1 F H1 J1 L L1 L20 L30 ∅P Q Typ 4.40 0.61 1.14 0.48 15.25 Max Min 4.60 0.88 1.70 0.70 15.75 0.173 0.024 0.044 0.019 0.6 10.40 2.70 5.15 1.32 6.60 2.72 14 3.93 0.393 0.094 0.194 0.048 0.244 0.094 0.511 0.137 1.27 10 2.40 4.95 1.23 6.20 2.40 13 3.50 Doc ID 8936 Rev 7 Max 0.181 0.034 0.066 0.027 0.62 0.050 16.40 28.90 3.75 2.65 Typ 0.409 0.106 0.202 0.051 0.256 0.107 0.551 0.154 0.645 1.137 3.85 2.95 0.147 0.104 0.151 0.116 13/17 Package mechanical data STB11NK40Z, STP11NK40ZFP, STP11NK40Z TO-220FP mechanical data mm Dim. Min. Typ. Max. A 4.4 4.6 B 2.5 2.7 D 2.5 2.75 E 0.45 0.7 F 0.75 1 F1 1.15 1.70 F2 1.15 1.5 G 4.95 5.2 G1 2.4 2.7 H 10 10.4 L2 16 L3 28.6 30.6 L4 9.8 10.6 L5 2.9 3.6 L6 15.9 16.4 L7 9 9.3 Dia 3 3.2 L7 E A B D Dia L5 L6 F1 F2 F G H G1 L4 L2 L3 7012510_Rev_J 14/17 Doc ID 8936 Rev 7 STB11NK40Z, STP11NK40ZFP, STP11NK40Z 5 Packaging mechanical data Packaging mechanical data D2PAK FOOTPRINT TAPE AND REEL SHIPMENT REEL MECHANICAL DATA DIM. mm MIN. A B 1.5 C 12.8 D 20.2 G 24.4 N 100 T TAPE MECHANICAL DATA DIM. mm inch MIN. MAX. MIN. A0 10.5 10.7 0.413 0.421 B0 15.7 15.9 0.618 0.626 inch MAX. MIN. MAX. 330 12.992 13.2 0.504 0.520 26.4 0.960 1.039 0.059 0795 3.937 30.4 1.197 BASE QTY BULK QTY 1000 1000 MAX. D 1.5 1.6 0.059 0.063 D1 1.59 1.61 0.062 0.063 E 1.65 1.85 0.065 0.073 F 11.4 11.6 0.449 0.456 K0 4.8 5.0 0.189 0.197 P0 3.9 4.1 0.153 0.161 P1 11.9 12.1 0.468 0.476 P2 1.9 2.1 0.075 0.082 R 50 1.574 T 0.25 0.35 0.0098 0.0137 W 23.7 24.3 0.933 0.956 * on sales type Doc ID 8936 Rev 7 15/17 Revision history 6 STB11NK40Z, STP11NK40ZFP, STP11NK40Z Revision history Table 10. 16/17 Document revision history Date Revision Changes 23-Aug-2005 2 Preliminary version 28-Oct-2005 3 Complete version 26-Jul-2006 4 New template, no content change 22-Nov-2006 5 Corrected unit on Table 5.: On/off states 18-Jan-2007 6 Typo mistakes on page 1 20-Apr-2009 7 Updated mechanical data Doc ID 8936 Rev 7 STB11NK40Z, STP11NK40ZFP, STP11NK40Z Please Read Carefully: Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST’s terms and conditions of sale. Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein. UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY, DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK. Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST. ST and the ST logo are trademarks or registered trademarks of ST in various countries. Information in this document supersedes and replaces all information previously supplied. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners. © 2009 STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com Doc ID 8936 Rev 7 17/17