Wire Wound Chip Inductor High Q Type LWQ0805 - LWQ1008 Wire Wound Chip Inductor – High Q Type Features RC0201 RC0201 RC0201 Ceramic base provides high SRF Ultra-compact inductors provide high Q factors Miniature SMD chip inductor for fully automated assembly Outstanding endurance from pull-up force, mechanical shock and pressure Tight tolerance down to +/- 2% RoHS Compliant Applications RF products: Cellular Phone (CDMA/GSM/PHS) Cordless Phone (DECT/CT1CT2) Remote Control, Security System Wireless PDA WILL, Wireless LAN/ Mouse/ Keyboard/ Earphone VCO, RF Module & Other Wireless Products Base Station, Repeater GPS Receiver Broad Band Applications: CATV Filter, Tuner Cable Modem/ XDSL Tuner Set Top Box IT Applications: USB 2.0 IEEE 1394 TAITRON COMPONENTS INCORPORATED www.taitroncomponents.com Tel: (800)-TAITRON Fax: (800)-TAITFAX (800)-824-8766 (800)-824-8329 (661)-257-6060 (661)-257-6415 Rev. B/NX Page 1 of 9 169 Wire Wound Chip Inductor – High Q Type LWQ0805 - LWQ1008 Constructions and Dimensions Item Material ① Ceramic Core ② Magnet Wire ③ Electrode (Ag/Pd+Ni+Sn) ④ UV Glue Teminal Wraparound: Approx. 0.007”/0.18mm on both ends Unit=mm Type Size In Inch A Max. B Max. C Max. D Ref. E F G H I J LWQ0805 0805 2.29 1.73 1.03 0.51 1.27 0.44 1.02 1.78 1.02 0.76 LWQ1008 1008 2.92 2.79 1.40 0.65 2.03 0.51 1.52 2.54 1.02 1.27 Color Dot Coding 0805Type (1008 type has no color coding) Because of samll sizes, these parts are marked with a single color dot. The inductance value represented by the dot is shown on the data for each type. Rev. B/NX www.taitroncomponents.com Page 2 of 9 Wire Wound Chip Inductor – High Q Type LWQ0805 - LWQ1008 Electrical Specifications LWQ0805 Type: Inductance (nH) Tolerance (%) L Freq. (MHz) Quality Factor Min. SRF Min. (GHz) DCR Max. (Ω) IDC Max. (mA) Color Code 2.5 ±5, 10% 250 80 @ 1500MHz 6.00 0.020 1600 None 5.6 ±5, 10% 250 98 @ 1500MHz 6.00 0.035 1600 Brown 6.2 ±5, 10% 250 88 @ 1000MHz 4.75 0.035 1600 Red 6.8 ±5, 10% 250 80 @ 1000MHz 4.40 0.035 1600 White 8.2 ±5, 10% 250 75@ 1000MHz 3.00 0.075 1000 Gray 10 ±5, 10% 250 80 @ 1000MHz 3.00 0.060 1600 None 12 ±5, 10% 250 80 @ 1000MHz 3.00 0.045 1600 Orange 15 ±2, 5, 10% 250 80 @ 1000MHz 2.80 0.100 1200 None 16 ±2, 5, 10% 250 72 @ 500MHz 2.95 0.060 1500 Yellow 18 ±2, 5, 10% 250 75 @ 500MHz 2.55 0.060 1400 Green 20 ±2, 5, 10% 250 70 @ 500MHz 2.05 0.055 1400 Blue 22 ±2, 5, 10% 250 80 @ 500MHz 2.00 0.100 1200 None 27 ±2, 5, 10% 250 75 @ 500MHz 2.00 0.070 1300 Violet 30 ±2, 5, 10% 250 65 @ 500MHz 1.95 0.095 1200 Gray 39 ±2, 5, 10% 250 65 @ 500MHz 1.60 0.110 1100 White 48 ±2, 5, 10% 200 65 @ 500MHz 1.40 0.095 1200 None 51 ±2, 5, 10% 200 65 @ 500MHz 1.40 0.120 1000 Brown Rev. B/NX www.taitroncomponents.com Page 3 of 9 Wire Wound Chip Inductor – High Q Type LWQ0805 - LWQ1008 LWQ1008 Type: Inductance (nH) Tolerance (%) L Freq. (MHz) Quality Factor Min. SRF Min. (GHz) DCR Max. (Ω) IDC Max. (mA) 3.0 ±5, 10% 50 70 @ 1500MHz 6.00 0.04 1600 3.9 ±5, 10% 50 75 @ 500MHz 6.00 0.05 1600 4.1 ±5, 10% 50 75 @ 1500MHz 6.00 0.05 1600 7.8 ±5, 10% 50 75 @ 500MHz 3.80 0.05 1600 10 ±2, 5, 10% 50 60 @ 500MHz 3.60 0.06 1600 12 ±2, 5, 10% 50 70 @ 500MHz 2.80 0.06 1500 18 ±2, 5, 10% 50 62 @ 350MHz 2.70 0.07 1400 22 ±2, 5, 10% 50 62 @ 350MHz 2.05 0.07 1400 33 ±2, 5, 10% 50 75 @ 350MHz 1.70 0.09 1300 39 ±2, 5, 10% 50 75 @ 350MHz 1.30 0.09 1300 47 ±2, 5, 10% 50 75 @ 350MHz 1.45 0.12 1200 56 ±2, 5, 10% 50 75 @ 350MHz 1.23 0.12 1200 68 ±2, 5, 10% 50 80 @ 350MHz 1.15 0.13 1100 82 ±2, 5, 10% 50 80 @ 350MHz 1.06 0.16 1100 100 ±2, 5, 10% 50 50 @ 350MHz 0.82 0.16 1000 Rev. B/NX www.taitroncomponents.com Page 4 of 9 Wire Wound Chip Inductor – High Q Type LWQ0805 - LWQ1008 Environment Characteristics Electrical Performance Test Test Item Inductance Q Value SRF DC Resistance RDC Test Method Requirement HP4286 HP4286 HP4287 Micro-Ohm meter (Gom-801G) Applied the current to coils, The inductance change should be less than 10% to initial value. Refer to standard electrical characteristic spec. Over Load Applied 2 times of rated allowed DC current to inductor for a period of 5 minutes Inductors shall have no evidence of electrical and mechanical damage Withstanding Voltage AC voltage of 500 VAC applied between inductor terminals and case for 1 min. Inductors shall have no evidence of electrical and mechanical damage Insulation Resistance 100 VDC applied between inductor terminal and case 1000M ohm min. Rated Current IDC Mechanical Performance Test Test Item Vibration Resistance to Soldering Heat Component Adhesion (Push Test) Drop Solderability Resistance to Solvent Test Method Test device shall be soldered on the substrate Oscillation Frequency: 10 to 55 to 10Hz for 1 min. Amplitude: 1.5mm Time: 2 hrs for each axis (X, Y & Z), total 6 hrs Solder Temperature: 270±5C Immersion Time: 10±2 seconds The device should be soldered (260±5 for 10 seconds) to a tinned copper substrate. A dynamiter force gauge should be applied to the side of the component. The device must withstand a minimum force of 2 or 4 pounds without a failure of adhesion on termination Dropping chip by each side and each corner. Drop 10 times in total Drop height: 100 cm Drop weight: 125 g Inductor shall be dipped in a melted solder bath at 245℃±5℃ for 3 seconds MIL-STD202F, Method 215D Requirement Appearance :No damage L change: within ±5% Q change: within ±10% 3 lbs. No damage 90% covered with solder No damage on appearance and marking Rev. B/NX www.taitroncomponents.com Page 5 of 9 Wire Wound Chip Inductor – High Q Type LWQ0805 - LWQ1008 Climatic Test Test Item Temperature Characteristic Humidity Low Temperature Storage Thermal Shock High Temperature Storage High Temperature Load Life Damp Heat with Load Test Method Requirement -40~+125°C Temperature: 40±2°C Relative Humidity: 90~95% Time: 96±2 hrs Measured after exposure in the room condition for 2 hrs Temperature: -40±2°C Time: 96±2 hrs Inductors are tested after 1 hour at room temperature One cycle: Step Temperature（°C） Time（min.） 1 -25±3 30 2 25±2 15 3 125±3 30 4 25±2 15 Total: 5 cycles Temperature: 125±2°C Time: 96±2 hrs Measured after exposure in the room condition for 1hour Temperature: 85±2°C Time: 1000±12 hrs Load: Allowed DC current Temperature: 40±2°C Relative Humidity: 90~95% Time: 1000±12 hrs Load: Allowed DC current Appearance: No damage L change: within ±10% Q change: within ±20% There should be no evidence or short of open circuit. ■ Storage Temperature: 25±3°C; Humidity < 80%RH Rev. B/NX www.taitroncomponents.com Page 6 of 9 Wire Wound Chip Inductor – High Q Type LWQ0805 - LWQ1008 Packing Information: Reel Specifications Unit: mm Type A B C W T LWQ0805 178.0 ± 2.0 60 ± 0.5 13.0 ± 0.3 9.0 ± 0.3 11.4 ± 1.0 LWQ1008 178.0 ± 2.0 60 ± 0.5 13.0 ± 0.3 9.0 ± 0.3 11.4 ± 1.0 Embossed Plastic Tape Specifications and Packaging Quantity Unit: mm Type A B C D E F G H I Reel (EA) LWQ0805 8 ± 0.2 1.85 ±0.1 4 ± 0.1 2.30 ±0.1 3.5 ±0.05 1.75±0.1 2 ± 0.05 1.45±0.05 0.23±0.05 2000 LWQ1008 8 ± 0.2 2.70 ±0.1 4 ± 0.1 2.80 ±0.1 3.5 ±0.05 1.75±0.1 2 ± 0.05 2.00±0.05 0.23±0.05 2000 Rev. B/NX www.taitroncomponents.com Page 7 of 9 Wire Wound Chip Inductor – High Q Type LWQ0805 - LWQ1008 How to Order LWQ 0805 T 15N G- xx -TR70 Packing Code TR70:7” Reel, RoHS Factory Location Code Tolerance Code: G: ±2%; J: ±5%; K: ±10%; Inductance Code: 3N9:3.9nH; 15N: 15nH R10:100nH; T: Material Code Size Code in inch(mm) 0805(2012); 1008(2520); Taitron Wire Wound Chip Inductor - High Q Type Rev. B/NX www.taitroncomponents.com Page 8 of 9 Wire Wound Chip Inductor – High Q Type LWQ0805 - LWQ1008 How to contact us US HEADQUARTERS 28040 WEST HARRISON PARKWAY, VALENCIA, CA 91355-4162 Tel: (800)-TAITRON (800)-824-8766 (661)-257-6060 Fax: (800)-TAITFAX (800)-824-8329 (661)-257-6415 Email: [email protected] Http://www.taitroncomponents.com TAITRON COMPONENTS MEXICO, S.A .DE C.V. BOULEVARD CENTRAL 5000 INTERIOR 5 PARQUE INDUSTRIAL ATITALAQUIA, HIDALGO C.P. 42970 MEXICO Tel: +52-55-5560-1519 Fax: +52-55-5560-2190 TAITRON COMPONENTS INCORPORATED TAIWAN, TAIPEI 6F., No.190, Sec. 2, Zhongxing Rd., Xindian Dist., New Taipei City 23146, Taiwan R.O.C. Tel: 886-2-2913-6238 Fax: 886-2-2913-6239 TAITRON COMPONENT TECHNOLOGY, SHANGHAI CORPORATION METROBANK PLAZA,1160 WEST YAN’AN ROAD, SUITE 1503, SHANGHAI,200052, CHINA Tel: +86-21-5424-9942 Fax: +86-21-2302-5027 CROSS REGION PLAZA, 899 LINGLING ROAD, SUITE 18C, SHANGHAI, 200030, CHINA Tel: +86-21-5424-9942 Fax: +86-21-5424-9931 Rev. B/NX www.taitroncomponents.com Page 9 of 9