SS12 - SS115 1.0 AMP. Surface Mount Schottky Barrier Rectifiers SMA/DO-214AC Features For surface mounted application Easy pick and place Metal to silicon rectifier, majority carrier conduction Low power loss, high efficiency High current capability, low VF High surge current capability Plastic material used carriers Underwriters Laboratory Classification 94V-0 Epitaxial construction High temperature soldering: 260oC / 10 seconds at terminals Mechanical Data Case: JEDEC SMA/DO-214AC Molded plastic Terminals: Pure tin plated, lead free Polarity: Indicated by cathode band Packaging: 12mm tape per EIA STD RS-481 Weight: 0.066 gram Dimensions in inches and (millimeters) Maximum Ratings and Electrical Characteristics Rating at 25oC ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20% Symbol SS SS SS SS Type Number Maximum Recurrent Peak Reverse Voltage Maximum RMS Voltage Maximum DC Blocking Voltage Maximum Average Forward Rectified Current at TL(See Fig. 1) Peak Forward Surge Current, 8.3 ms Single Half Sine-wave Superimposed on Rated Load (JEDEC method ) Maximum Instantaneous Forward Voltage o (Note 1) IF= 1.0A @ 25 C @ 100oC o Maximum DC Reverse Current @ TA =25 C at Rated DC Blocking Voltage @ TA=125 oC Maximum DC Reverse Current at VR=33V & TA=50 oC Typical Junction Capacitance (Note 3) Typical Thermal Resistance ( Note 2 ) VRRM VRMS VDC 12 20 14 20 13 30 21 30 14 40 28 40 SS 16 60 42 60 15 50 35 50 SS 19 90 63 90 SS 110 100 70 100 SS Units 115 150 V 105 V 150 V I(AV) 1.0 A IFSM 30 A 0.5 0.4 VF 0.75 0.65 0.4 IR 10 5.0 - HTIR Cj 0.80 0.95 0.70 0.85 0.1 2.0 mA mA 5.0 uA V 50 R ΘJL 28 88 R θJA Operating Temperature Range TJ -65 to +125 -65 to +150 Storage Temperature Range TSTG -65 to +150 Notes: 1. Pulse Test with PW=300 usec, 1% Duty Cycle 2. Measured on P.C.Board with 0.2” x 0.2” (5.0mm x 5.0mm) Copper Pad Areas. 3. Measured at 1 MHz and Applied Reverse Voltage of 4.0V D.C. - 32 - pF o C/W o o C C Version: C07 RATINGS AND CHARACTERISTIC CURVES (SS12 THRU SS115) FIG.1- MAXIMUM FORWARD CURRENT DERATING CURVE FIG.2- MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT 50 RESISTIVE OR INDUCTIVE LOAD SS12- SS14 SS15-SS115 0.5 PCB MOUNTED ON 0.2X0.2" (5.0X5.0mm) COPPER PAD AREAS 0 PEAK FORWARD SURGE CURRENT. (A) AVERAGE FORWARD CURRENT. (A) 1.0 AT RATED TL 8.3ms Single Half Sine Wave JEDEC Method 40 30 20 10 0 50 60 70 80 90 100 110 120 130 140 150 160 1 170 10 NUMBER OF CYCLES AT 60Hz o LEAD TEMPERATURE. ( C) 100 FIG.4- TYPICAL REVERSE CHARACTERISTICS FIG.3- TYPICAL FORWARD CHARACTERISTICS 100 50 SS12-SS14 SS15-SS115 SS15-SS16 10 INSTANTANEOUS FORWARD CURRENT. (A) INSTANTANEOUS REVERSE CURRENT. (mA) SS19-SS110 SS12-SS14 1 SS115 0.1 10 Tj=125 0C 1 Tj=75 0C 0.1 0.01 O Tj=25 C PULSE WIDTH=300 S 1% DUTY CYCLE 0.001 0.01 0 .2 .4 .6 .8 1.0 1.2 1.4 1.6 FORWARD VOLTAGE. (V) 0 Tj=25 C f=1.0MHz Vsig=50mVp-p SS12-SS14 SS15-SS16 SS19-SS115 100 1.0 10 100 TRANSIENT THERMAL IMPEDANCE. (OC/W) 100 400 JUNCTION CAPACITANCE.(pF) 20 40 60 80 100 120 140 PERCENT OF RATED PEAK REVERSE VOLTAGE. (%) FIG.6- TYPICAL TRANSIENT THERMAL CHARACTERISTICS FIG.5- TYPICAL JUNCTION CAPACITANCE 10 0.1 0 10 1 0.1 0.01 REVERSE VOLTAGE. (V) 0.1 1 10 T, PULSE DURATION. (sec) Version: C07 100