UTC-IC R200LD10

UNISONIC TECHNOLOGIES CO., LTD
R200LD10
LINEAR INTEGRATED CIRCUIT
VOLTAGE REGULATOR
„
DESCRIPTION
The UTC R200LD10 shows a high current, high accuracy,
low-dropout voltage. The features are: low dropout voltage, very
low ground current. Cause the series have been designed for
high current loads, so they are also used in lower current,
extremely low dropout-critical systems (in which their tiny
dropout voltage and ground current values are important
attributes).
„
FEATURES
* Built-in ON/OFF function,
* Over current protection function,
* ASO protection function
* Overheat protection function
* 0.3A / 3.3V(R1=2KΩ)
Output low dropout voltage regulator
Lead-free:
R200LD10L
Halogen-free: R200LD10G
„
ORDERING INFORMATION
Normal
R200LD10-TN4-R
R200LD10-TN4-T
R200LD10-TN5-R
R200LD10-TN5-T
Ordering Number
Lead Free
R200LD10L-TN4-R
R200LD10L-TN4-T
R200LD10L-TN5-R
R200LD10L-TN5-T
www.unisonic.com.tw
Copyright © 2008 Unisonic Technologies Co., Ltd
Halogen Free
R200LD10G-TN4-R
R200LD10G-TN4-T
R200LD10G-TN5-R
R200LD10G-TN5-T
Package
Packing
TO-252-4
TO-252-4
TO-252-5
TO-252-5
Tape Reel
Tube
Tape Reel
Tube
1 of 9
QW-R101-022.D
R200LD10
„
LINEAR INTEGRATED CIRCUIT
PIN DESCRIPTIONS
PIN NO.
1
2
3
4
5
PIN NAME
VIN
VC
VOUT
VADJ
GND
PIN FUNCTION
DC Input Voltage.
On/Off Control
DC Output Voltage.
Output Voltage Adjustment
Ground
UNISONIC TECHNOLOGIES CO., LTD
www.unisonic.com.tw
2 of 9
QW-R101-022.D
R200LD10
„
LINEAR INTEGRATED CIRCUIT
BLOCK DIAGRAM
VIN
1
VC
2
3 VOUT
STARTING
CIRCUIT
REFERENCE
VOLTAGE
OTP
OVERCURRENT
PROTECTION
SOA
PROTE
CTION
4
VADJ
5
GND
UNISONIC TECHNOLOGIES CO., LTD
www.unisonic.com.tw
3 of 9
QW-R101-022.D
R200LD10
„
LINEAR INTEGRATED CIRCUIT
ABSOLUTE MAXIMUM RATINGS (Ta=25°C)
PARAMETER
SYMBOL
RATINGS
UNITS
Input Voltage (Note 2)
VIN
24
V
ON/OFF Control Terminal Voltage (Note 2)
VC
24
V
Output Adjustment Pin Voltage (Note 2)
VADJ
5
V
Output Current
IOUT
1
A
Power Dissipation (with infinite heat sink)
PD
8
W
Junction Temperature
TJ
+150
°C
Operating Temperature
TOPR
-40 ~ +85
°C
Storage Temperature
TSTG
-40 ~ +150
°C
Note: 1.Absolute maximum ratings are those values beyond which the device could be permanently damaged.
Absolute maximum ratings are stress ratings only and functional device operation is not implied.
2.All are open except GND and applicable terminals.
„
ELECTRICAL CHARACTERISTICS
(VI N=5V, VOUT=3.3 V(R1=2kΩ), IOUT=0.3A, VC=2.7V, TJ=25°C, CI=0.33μF, CO=10μF, unless otherwise specified)
PARAMETER
SYMBOL
CONDITIONS
MIN TYP MAX UNITS
Input Voltage
VIN
3.5
24
V
Output Voltage
VOUT
3.0
20
V
Load Regulation
ΔVOUT/ΔIOUT IOUT = 5mA~ 1A
1.0
%
Line Regulation
ΔVOUT/ΔVIN VIN = 4~ 10V, IOUT=5mA
1.0
Ripple Rejection
RR
Refer to Fig 3
60
dB
Dropout Voltage
VD
VIN=3.5V
0.5
V
Reference Voltage
VREF
2.583 2.65 2.717
Temperature Coefficient of Reference
TCVREF
TJ =0 ~ 125°C, IOUT = 5mA
±1.0
%
Voltage
On-State Voltage for Control
VC(ON)
(Note)
2.0
V
On-State Current for Control
IC(ON)
200
μA
On-State Voltage for Control
VC(OFF)
IOUT=0A
0.8
V
On-State Current for Control
IC(OFF)
IOUT=0A,VC=0.4V
-2
μA
Quiescent Current
IQ
IOUT=0A
8
mA
Output Off-State Consumption Current
IQS
VC=0.4V
5
μA
Note: In case of VC pin, output voltage turns OFF.
UNISONIC TECHNOLOGIES CO., LTD
www.unisonic.com.tw
4 of 9
QW-R101-022.D
R200LD10
„
LINEAR INTEGRATED CIRCUIT
TYPICAL APPLICATION CIRCUIT
UNISONIC TECHNOLOGIES CO., LTD
www.unisonic.com.tw
5 of 9
QW-R101-022.D
R200LD10
„
LINEAR INTEGRATED CIRCUIT
TEST CIRCUIT
For Standard Measuring Circuit of Regulation Portion
DC Input
A
CO=10μF
CI=0.33μF
4
2
5
IC
IOUT
R2
R200LD10
VIN
VOUT
3
3
1
R1
A
A
V
RL
IQ
VOUT=VREF*(1+R2/R1)
R1=2kΩ,VREF≈2.65V
For Standard Measuring Circuit of Ripple Rejection Critical Rate
DC Input
ei
+
3
3
1
IOUT
R2
R200LD10
VOUT
~
VIN
CO=10μF
CI=0.33μF
eo
4
2
5
V~
V
R1
RL
2.7V
f=120Hz sine wave ,ei(rms)=0.5V ,
VIN=5V,VOUT=3.3V(R1=2kΩ)
IOUT=0.3A,RR=20log{ei(rms)/eo(rms)}
UNISONIC TECHNOLOGIES CO., LTD
www.unisonic.com.tw
6 of 9
QW-R101-022.D
R200LD10
„
LINEAR INTEGRATED CIRCUIT
TYPICAL CHARACTERISTICS
UNISONIC TECHNOLOGIES CO., LTD
www.unisonic.com.tw
7 of 9
QW-R101-022.D
R200LD10
„
LINEAR INTEGRATED CIRCUIT
TYPICAL CHARACTERISTICS(Cont.)
UNISONIC TECHNOLOGIES CO., LTD
www.unisonic.com.tw
8 of 9
QW-R101-022.D
R200LD10
LINEAR INTEGRATED CIRCUIT
UTC assumes no responsibility for equipment failures that result from using products at values that
exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges, or
other parameters) listed in products specifications of any and all UTC products described or contained
herein. UTC products are not designed for use in life support appliances, devices or systems where
malfunction of these products can be reasonably expected to result in personal injury. Reproduction in
whole or in part is prohibited without the prior written consent of the copyright owner. The information
presented in this document does not form part of any quotation or contract, is believed to be accurate
and reliable and may be changed without notice.
UNISONIC TECHNOLOGIES CO., LTD
www.unisonic.com.tw
9 of 9
QW-R101-022.D