TC620/TC621 5V, Dual Trip Point Temperature Sensors Features: Package Type • User Programmable Hysteresis and Temperature Set Point • Easily Programs with 2 External Resistors • Wide Temperature Detection Range: -0°C to 70°C: (TC620/TC621CCX) 8-PDIP NC 1 LOW SET 2 HIGH SET 3 TC620XCPA TC620XEPA 6 LOW LIMIT 5 CONTROL GND 4 -40°C to +125°C: (TC620/TC621CVX) VDD 7 HIGH LIMIT 8 8-PDIP -40°C to +85°C: (TC620/TC621CEX) -55°C to +125°C: (TC620/TC621CMX) • Onboard Temperature Sensing Applications (TC620X) • External NTC Thermistor for Remote Sensing Applications (TC621X) • Available in 8-Pin PDIP and SOIC Packages Applications: • • • • HIGH SET 2 LOW SET 3 Device Selection Table Part Number Package Temperature Range TC620X*COA 8-Pin SOIC 0°C to +70°C TC620X*CPA 8-Pin PDIP 0°C to +70°C TC620X*EOA 8-Pin SOIC -40°C to +85°C TC620X*EPA 8-Pin PDIP -40°C to +85°C TC620C*VOA 8-Pin SOIC -40°C to +125°C TC621X*COA 8-Pin SOIC 0°C to +70°C TC621X*CPA 8-Pin PDIP 0°C to +70°C TC621X*EOA 8-Pin SOIC -40°C to +85°C TC621X*EPA 8-Pin PDIP -40°C to +85°C *The part code will be C or H (see Functional Block Diagrams). VDD 7 HIGH LIMIT 8 TC621XCPA TC621XEPA 6 LOW LIMIT 5 CONTROL GND 4 8-SOIC NC 1 8 VDD LOW SET 2 7 LOW LIMIT 5 CONTROL HIGH SET 3 Power Supply Over Temperature Detection Consumer Equipment Temperature Regulators CPU Thermal Protection Note: THERMISTOR 1 GND 4 TC620XCOA TC620XEOA 6 HIGH LIMIT TC620CVOA 8-SOIC THERMISTOR 1 HIGH SET 2 VDD HIGH LIMIT 7 8 LOW SET 3 TC621XCOA TC621XEOA 6 LOW LIMIT GND 4 5 CONTROL General Description: The TC620 and TC621 are programmable logic output temperature detectors designed for use in thermal management applications. The TC620 features an onboard temperature sensor, while the TC621 connects to an external NTC thermistor for remote sensing applications. Both devices feature dual thermal interrupt outputs (HIGH LIMIT and LOW LIMIT), each of which is programmed with a single external resistor. On the TC620, these outputs are driven active (high) when measured temperature equals the user programmed limits. The CONTROL (hysteresis) output is driven high when temperature equals the high limit setting and returns low when temperature falls below the low limit setting. This output can be used to provide ON/OFF control to a cooling fan or heater. The TC621 provides the same output functions except that the logical states are inverted. The TC620/TC621 are usable over operating temperature ranges of 0°C to 70°C, -40°C to +125°C and -55°C to 125°C. 2001-2012 Microchip Technology Inc. DS21439D-page 1 TC620/TC621 Functional Block Diagrams VDD 8 Temp. to Voltage Converter 4 TC620 + 2 LOW SET VREF GEN 7 LOW LIMIT – VREF + HIGH SET 3 VREF GEN 6 HIGH LIMIT – R S Q Q 5 CONTROL* VDD 8 1 THERMISTOR Thermistor Interface Circuit 4 TC621 + HIGH SET 2 VREF GEN 7 HIGH LIMIT – VREF + LOW SET 3 VREF GEN 6 LOW LIMIT – R S Q Q 5 CONTROL* *Suffix code "C" denotes cooling option (High true CONTROL output). Suffix code "H" denotes heating option (Low true CONTROL output). DS21439D-page 2 2001-2012 Microchip Technology Inc. TC620/TC621 1.0 ELECTRICAL CHARACTERISTICS *Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only and functional operation of the device at these or any other conditions above those indicated in the operation sections of the specifications is not implied. Exposure to Absolute Maximum Rating conditions for extended periods may affect device reliability. Absolute Maximum Ratings* Supply Voltage ....................................................... 20V Input Voltage Any Input .. (GND – 0.3V) to (VDD +0.3V) Package Power Dissipation (TA 70°C) PDIP ............................................. 730 mW SOIC ............................................. 470 mW Derating Factors: Plastic .......................................... 8 mW/°C Operating Temperature: M Version......................... -55°C to +125°C V Version ......................... -40°C to +125°C E Version ........................... -40°C to +85°C C Version .............................. 0°C to +70°C Storage Temperature ......................... -65°C to +150°C TC620/TC621 ELECTRICAL SPECIFICATIONS Electrical Characteristics: TA = 25°C, unless otherwise specified. Symbol Parameter VDD Supply Voltage Range Min Typ Max Unit 4.5 — 18 V Test Conditions IDD Supply Current — 270 400 A 5V VDD 18V ROUT Output Resistance — 400 1000 W Output High or Low, 5V VDD 18V IOUT Output Current — — 1 mA Temp. Sensed Source/Sink IOUT Output Current — — 1 mA Cool/Heat Source/Sink TERR Absolute Accuracy T-3 T T+3 °C T = Programmed Temperature 2001-2012 Microchip Technology Inc. DS21439D-page 3 TC620/TC621 2.0 PIN DESCRIPTIONS The descriptions of the pins are listed in Table 2-1. TABLE 2-1: PIN FUNCTION TABLE Pin No. (8-Pin PDIP) (8-Pin SOIC) 0°C to +70°C -40°C to +85°C -40°C to +125°C Symbol 1 NC 2 LOW SET Low temperature set point. Connect an external 1% resistor from LOW SET to VDD to set trip point. 3 HIGH SET High temperature set point. Connect an external 1% resistor from HIGH SET to VDD to set trip point. 4 GND Description No Internal Connection. Ground Terminal. 5 CONTROL Control output. 6 HIGH LIMIT High temperature push/pull output. 7 LOW LIMIT Low temperature push/pull output. 8 VDD Power supply input. Pin No. (8-Pin PDIP) (8-Pin SOIC) 0°C to +70°C -40°C to +85°C Symbol 1 THERMISTOR 2 HIGH SET High temperature set point. Connect an external 1% resistor from HIGH SET to VDD to set trip point. 3 LOW SET Low temperature set point. Connect an external 1% resistor from LOW SET to VDD to set trip point. Description Thermistor input. 4 GND 5 CONTROL Control output. 6 LOW LIMIT Low temperature push/pull output. 7 HIGH LIMIT 8 VDD DS21439D-page 4 Ground Terminal. High temperature push/pull output. Power supply input. 2001-2012 Microchip Technology Inc. TC620/TC621 DETAILED DESCRIPTION The TC620 has a positive temperature coefficient temperature sensor and a dual threshold detector. Temperature set point programming is accomplished with external resistors from the HIGH SET and LOW SET inputs to VDD. The HIGH LIMIT and LOW LIMIT outputs remain low as long as measured temperature is below set point values. As measured temperature increases, the LOW LIMIT output is driven high when temperature equals the LOW SET set point (±3°C max). If temperature continues to climb, the HIGH LIMIT output is driven high when temperature equals the HIGH SET set point (Figure 3-1). The CONTROL (hysteresis) output is latched in its active state at the temperature specified by the HIGH SET resistor. CONTROL is maintained active until temperature falls to the value specified by the LOW SET resistor. Care must also be taken to ensure the LOW SET temperature setting is at least 5°C lower than the HIGH SET temperature setting. Figure 3-2 can help the user obtain an estimate of the external resistor values required for the desired LOW SET and HIGH SET trip points. 250 RESISTANCE, RTRIP (kΩ) 3.0 200 150 100 50 -55 -35 -15 5 25 45 65 85 105 125 TEMPERATURE (°C) High Set Point Temperature Low Set Point Low Limit Output FIGURE 3-2: Trip Temperature 3.2 TC620 Sense Resistors vs. Built-in Hysteresis High Limit Output Control Output (Cool Option Control Output (Heat Option) FIGURE 3-1: Output Logic 3.1 TC620/TC621 Input vs. To prevent output “chattering” when measured temperature is at (or near) the programmed trip point values, the LOW SET and HIGH SET inputs each have built-in hysteresis of -2°C below the programmed settings (Figure 3-3). Programming the TC620 The resistor values to achieve the desired trip point temperatures on HIGH SET and LOW SET are calculated using Equation 3-1: Set Point (Set Point 2°C) EQUATION 3-1: RTRIP = 0.5997 x T 2.1312 High Limit or Low Limit Output Where: RTRIP = Programming resistor in Ohms T = The desired trip point temperature in degrees Kelvin. For example, a 50°C setting on either the HIGH SET or LOW SET input is calculated using Equation 3-2 as follows: FIGURE 3-3: Built-In Hysteresis on Low Limit and High Limit Outputs As shown, the outputs remain in their active state (hysteresis) until temperature falls an additional 2°C below the user’s setting. EQUATION 3-2: RSET = 0.5997 x ((50 + 273.15)2.1312) = 133.6 k Care must be taken to ensure the LOW SET programming resistor is a smaller value than the HIGH SET programming resistor. Failure to do this will result in erroneous operation of the CONTROL output. 2001-2012 Microchip Technology Inc. DS21439D-page 5 TC620/TC621 Using the TC621 The TC621 operation is similar to that of the TC620, but requires an external NTC thermistor. Use the resistance versus temperature curve of the thermistor to determine the values of the programming resistors. Note that the pin numbers for the HIGH SET and LOW SET programming resistors for the TC621 are reversed versus that of the TC620 (i.e., the resistor value on HIGH SET [Pin 2] should always be lower than the one connected to LOW SET [Pin 3]). Also note that the outputs of the TC621 are LOW TRUE when used with an NTC thermistor. 350 300 THERMISTOR RESISTANCE (kΩ) 3.3 250 200 150 100 50 0 0 3.4 10 TC621 Thermistor Selection 20 30 40 50 60 70 TEMPERATURE (°C) The TC621 uses an external thermistor to monitor the controlling temperature. A thermistor with a resistance value of approximately 100 k at 25°C is recommended. FIGURE 3-4: A temperature set point is selected by picking a resistor whose value is equal to the resistance of the thermistor at the desired temperature. For example, using the data shown in Figure 3-4, a 30 k resistor between HIGH TEMP (Pin 2) and VDD (Pin 8) sets the high temperature trip point at +51°C and a 49 k resistor on LOW TEMP (Pin 3) sets the low temperature trip point to +41°C. Both devices have complimentary output stages. They are rated at a source or sink current of 1 mA maximum. DS21439D-page 6 3.5 Typical NTC Thermistor TC620/TC621 Outputs 2001-2012 Microchip Technology Inc. TC620/TC621 4.0 TYPICAL APPLICATIONS 4.1 Dual Speed Temperature Control 4.2 Temperature Controlled Fan In the application in Figure 4-2, a high and a low temperature is selected by two RL and RH. The TC620 monitors the ambient temperature and turns the FET switch on when the temperature exceeds the HIGH TEMP set point. The fan remains on until the temperature decreases to the LOW TEMP set point. This provides the hysteresis. In this application, the fan turns on only when required. In Figure 4-1, the Dual Speed Temperature Control uses a TC620 and a TC4469 quad driver. Two of the drivers of the TC4469 are configured in a simple oscillator. When the temperature is below the LOW TEMP set point, the output of the driver is OFF. When the temperature exceeds the LOW TEMP set point, the TC4469 gates the oscillator signal to the outputs of the driver. This square wave signal modulates the remaining outputs and drives the motor at a low speed. If this speed cannot keep the temperature below the HIGH TEMP set point, then the driver turns on continuously which increases the fan speed to high. The TC620 will monitor the temperature and only allow the fan to operate when needed and at the required speed to maintain the desired temperature. A higher power option can be designed by adding a resistor and a power MOSFET. The TC621 uses an external thermistor to monitor the ambient temperature. This adds one part, but allows more flexibility with the location of the temperature sensor. +12V 0.1 µF 2 3 High Temp. 1 5 50˚C High 6 1N4148 Limit TC620 Low 7 Limit Temperature Scale 1M 1N4148 1 µF Fan Motor 14 2 1 3 5 8 TC4469 4 0˚C – 30˚C (Fan Off) 30˚C – 50˚C (Fan Low) 50˚C – UP (Fan High) FIGURE 4-1: 10 µF 8 Low Temp. 30˚C VMOTOR 10k 13 4 6 9 10 11 12 100k 50 Ω MOSFET 50 pF Higher Power Option 7 Fan Motor Dual Speed Temperature Control +12V +12V Thermistor (NTC) Low Temp. 1 RL 2 3 RH 4 High Temp. FIGURE 4-2: 8 TC620 Fan Motor 7 6 5 MTP3055E High Temp. 1 RH 3 Low Temp. RL 4 2 8 TC621 Fan Motor 7 6 5 MTP3055E Temperature Controlled Fan 2001-2012 Microchip Technology Inc. DS21439D-page 7 TC620/TC621 4.5V to 18V High Temp. Low Temp. 1 2 3 4 TC620 8 7 6 5 1 2 3 4 5 6 7 TC4469 14 13 12 11 10 9 8 1k 1k High Temp. Warning Low Temp. Warning Heating/Cooling Equipment FIGURE 4-3: DS21439D-page 8 Heating and Cooling Application 2001-2012 Microchip Technology Inc. TC620/TC621 5.0 PACKAGING INFORMATION 5.1 Package Marking Information Package marking data not available at this time. 5.2 Taping Form Component Taping Orientation for 8-Pin SOIC (Narrow) Devices User Direction of Feed Pin 1 W P Standard Reel Component Orientation for 713 Suffix Device Carrier Tape, Number of Components Per Reel and Reel Size Package 8-Pin SOIC (N) 2001-2012 Microchip Technology Inc. Carrier Width (W) Pitch (P) Part Per Full Reel Reel Size 12 mm 8 mm 2500 13 in DS21439D-page 9 TC620/TC621 5.3 Package Dimensions Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging 8-Pin Plastic DIP Pin 1 .260 (6.60) .240 (6.10) .045 (1.14) .030 (0.76) .070 (1.78) .040 (1.02) .310 (7.87) .290 (7.37) .400 (10.16) .348 (8.84) .200 (5.08) .140 (3.56) .040 (1.02) .020 (0.51) .150 (3.81) .115 (2.92) .110 (2.79) .090 (2.29) .015 (0.38) .008 (0.20) 3° Min. .400 (10.16) .310 (7.87) .022 (0.56) .015 (0.38) Dimensions: inches (mm) Package Dimensions (Continued) Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging 8-Pin SOIC Pin 1 .157 (3.99) .150 (3.81) .244 (6.20) .228 (5.79) .050 (1.27) Typ. .197 (5.00) .189 (4.80) .069 (1.75) .053 (1.35) .020 (0.51) .010 (0.25) .013 (0.33) .004 (0.10) .010 (0.25) .007 (0.18) 8° Max. .050 (1.27) .016 (0.40) Dimensions: inches (mm) DS21439D-page 10 2001-2012 Microchip Technology Inc. TC620/TC621 6.0 REVISION HISTORY Revision D (December 2012) Added a note to each package outline drawing. 2001-2012 Microchip Technology Inc. DS21439D-page 11 TC620/TC621 NOTES: DS21439D-page 12 2001-2012 Microchip Technology Inc. TC620/TC621 SALES AND SUPPORT Data Sheets Products supported by a preliminary Data Sheet may have an errata sheet describing minor operational differences and recommended workarounds. To determine if an errata sheet exists for a particular device, please contact one of the following: 1. 2. Your local Microchip sales office The Microchip Worldwide Site (www.microchip.com) Please specify which device, revision of silicon and Data Sheet (include Literature #) you are using. New Customer Notification System Register on our web site (www.microchip.com/cn) to receive the most current information on our products. 2001-2012 Microchip Technology Inc. DS21439D-page 13 TC620/TC621 NOTES: DS21439D-page 14 2001-2012 Microchip Technology Inc. Note the following details of the code protection feature on Microchip devices: • Microchip products meet the specification contained in their particular Microchip Data Sheet. • Microchip believes that its family of products is one of the most secure families of its kind on the market today, when used in the intended manner and under normal conditions. • There are dishonest and possibly illegal methods used to breach the code protection feature. All of these methods, to our knowledge, require using the Microchip products in a manner outside the operating specifications contained in Microchip’s Data Sheets. Most likely, the person doing so is engaged in theft of intellectual property. • Microchip is willing to work with the customer who is concerned about the integrity of their code. • Neither Microchip nor any other semiconductor manufacturer can guarantee the security of their code. Code protection does not mean that we are guaranteeing the product as “unbreakable.” Code protection is constantly evolving. We at Microchip are committed to continuously improving the code protection features of our products. Attempts to break Microchip’s code protection feature may be a violation of the Digital Millennium Copyright Act. If such acts allow unauthorized access to your software or other copyrighted work, you may have a right to sue for relief under that Act. Information contained in this publication regarding device applications and the like is provided only for your convenience and may be superseded by updates. It is your responsibility to ensure that your application meets with your specifications. MICROCHIP MAKES NO REPRESENTATIONS OR WARRANTIES OF ANY KIND WHETHER EXPRESS OR IMPLIED, WRITTEN OR ORAL, STATUTORY OR OTHERWISE, RELATED TO THE INFORMATION, INCLUDING BUT NOT LIMITED TO ITS CONDITION, QUALITY, PERFORMANCE, MERCHANTABILITY OR FITNESS FOR PURPOSE. Microchip disclaims all liability arising from this information and its use. Use of Microchip devices in life support and/or safety applications is entirely at the buyer’s risk, and the buyer agrees to defend, indemnify and hold harmless Microchip from any and all damages, claims, suits, or expenses resulting from such use. No licenses are conveyed, implicitly or otherwise, under any Microchip intellectual property rights. Trademarks The Microchip name and logo, the Microchip logo, dsPIC, FlashFlex, KEELOQ, KEELOQ logo, MPLAB, PIC, PICmicro, PICSTART, PIC32 logo, rfPIC, SST, SST Logo, SuperFlash and UNI/O are registered trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. FilterLab, Hampshire, HI-TECH C, Linear Active Thermistor, MTP, SEEVAL and The Embedded Control Solutions Company are registered trademarks of Microchip Technology Incorporated in the U.S.A. Silicon Storage Technology is a registered trademark of Microchip Technology Inc. in other countries. Analog-for-the-Digital Age, Application Maestro, BodyCom, chipKIT, chipKIT logo, CodeGuard, dsPICDEM, dsPICDEM.net, dsPICworks, dsSPEAK, ECAN, ECONOMONITOR, FanSense, HI-TIDE, In-Circuit Serial Programming, ICSP, Mindi, MiWi, MPASM, MPF, MPLAB Certified logo, MPLIB, MPLINK, mTouch, Omniscient Code Generation, PICC, PICC-18, PICDEM, PICDEM.net, PICkit, PICtail, REAL ICE, rfLAB, Select Mode, SQI, Serial Quad I/O, Total Endurance, TSHARC, UniWinDriver, WiperLock, ZENA and Z-Scale are trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. SQTP is a service mark of Microchip Technology Incorporated in the U.S.A. GestIC and ULPP are registered trademarks of Microchip Technology Germany II GmbH & Co. & KG, a subsidiary of Microchip Technology Inc., in other countries. All other trademarks mentioned herein are property of their respective companies. © 2001-2012, Microchip Technology Incorporated, Printed in the U.S.A., All Rights Reserved. Printed on recycled paper. ISBN: 9781620768235 QUALITY MANAGEMENT SYSTEM CERTIFIED BY DNV == ISO/TS 16949 == 2001-2012 Microchip Technology Inc. Microchip received ISO/TS-16949:2009 certification for its worldwide headquarters, design and wafer fabrication facilities in Chandler and Tempe, Arizona; Gresham, Oregon and design centers in California and India. The Company’s quality system processes and procedures are for its PIC® MCUs and dsPIC® DSCs, KEELOQ® code hopping devices, Serial EEPROMs, microperipherals, nonvolatile memory and analog products. In addition, Microchip’s quality system for the design and manufacture of development systems is ISO 9001:2000 certified. DS21439D-page 15 Worldwide Sales and Service AMERICAS ASIA/PACIFIC ASIA/PACIFIC EUROPE Corporate Office 2355 West Chandler Blvd. Chandler, AZ 85224-6199 Tel: 480-792-7200 Fax: 480-792-7277 Technical Support: http://www.microchip.com/ support Web Address: www.microchip.com Asia Pacific Office Suites 3707-14, 37th Floor Tower 6, The Gateway Harbour City, Kowloon Hong Kong Tel: 852-2401-1200 Fax: 852-2401-3431 India - Bangalore Tel: 91-80-3090-4444 Fax: 91-80-3090-4123 India - New Delhi Tel: 91-11-4160-8631 Fax: 91-11-4160-8632 Austria - Wels Tel: 43-7242-2244-39 Fax: 43-7242-2244-393 Denmark - Copenhagen Tel: 45-4450-2828 Fax: 45-4485-2829 India - Pune Tel: 91-20-2566-1512 Fax: 91-20-2566-1513 France - Paris Tel: 33-1-69-53-63-20 Fax: 33-1-69-30-90-79 Japan - Osaka Tel: 81-6-6152-7160 Fax: 81-6-6152-9310 Germany - Munich Tel: 49-89-627-144-0 Fax: 49-89-627-144-44 Atlanta Duluth, GA Tel: 678-957-9614 Fax: 678-957-1455 Boston Westborough, MA Tel: 774-760-0087 Fax: 774-760-0088 Chicago Itasca, IL Tel: 630-285-0071 Fax: 630-285-0075 Cleveland Independence, OH Tel: 216-447-0464 Fax: 216-447-0643 Dallas Addison, TX Tel: 972-818-7423 Fax: 972-818-2924 Detroit Farmington Hills, MI Tel: 248-538-2250 Fax: 248-538-2260 Indianapolis Noblesville, IN Tel: 317-773-8323 Fax: 317-773-5453 Los Angeles Mission Viejo, CA Tel: 949-462-9523 Fax: 949-462-9608 Santa Clara Santa Clara, CA Tel: 408-961-6444 Fax: 408-961-6445 Toronto Mississauga, Ontario, Canada Tel: 905-673-0699 Fax: 905-673-6509 Australia - Sydney Tel: 61-2-9868-6733 Fax: 61-2-9868-6755 China - Beijing Tel: 86-10-8569-7000 Fax: 86-10-8528-2104 China - Chengdu Tel: 86-28-8665-5511 Fax: 86-28-8665-7889 China - Chongqing Tel: 86-23-8980-9588 Fax: 86-23-8980-9500 Netherlands - Drunen Tel: 31-416-690399 Fax: 31-416-690340 Korea - Daegu Tel: 82-53-744-4301 Fax: 82-53-744-4302 Spain - Madrid Tel: 34-91-708-08-90 Fax: 34-91-708-08-91 China - Hangzhou Tel: 86-571-2819-3187 Fax: 86-571-2819-3189 Korea - Seoul Tel: 82-2-554-7200 Fax: 82-2-558-5932 or 82-2-558-5934 China - Hong Kong SAR Tel: 852-2943-5100 Fax: 852-2401-3431 Malaysia - Kuala Lumpur Tel: 60-3-6201-9857 Fax: 60-3-6201-9859 China - Nanjing Tel: 86-25-8473-2460 Fax: 86-25-8473-2470 Malaysia - Penang Tel: 60-4-227-8870 Fax: 60-4-227-4068 China - Qingdao Tel: 86-532-8502-7355 Fax: 86-532-8502-7205 Philippines - Manila Tel: 63-2-634-9065 Fax: 63-2-634-9069 China - Shanghai Tel: 86-21-5407-5533 Fax: 86-21-5407-5066 Singapore Tel: 65-6334-8870 Fax: 65-6334-8850 China - Shenyang Tel: 86-24-2334-2829 Fax: 86-24-2334-2393 Taiwan - Hsin Chu Tel: 886-3-5778-366 Fax: 886-3-5770-955 China - Shenzhen Tel: 86-755-8864-2200 Fax: 86-755-8203-1760 Taiwan - Kaohsiung Tel: 886-7-213-7828 Fax: 886-7-330-9305 China - Wuhan Tel: 86-27-5980-5300 Fax: 86-27-5980-5118 Taiwan - Taipei Tel: 886-2-2508-8600 Fax: 886-2-2508-0102 China - Xian Tel: 86-29-8833-7252 Fax: 86-29-8833-7256 Thailand - Bangkok Tel: 66-2-694-1351 Fax: 66-2-694-1350 UK - Wokingham Tel: 44-118-921-5869 Fax: 44-118-921-5820 China - Xiamen Tel: 86-592-2388138 Fax: 86-592-2388130 China - Zhuhai Tel: 86-756-3210040 Fax: 86-756-3210049 DS21439D-page 16 Italy - Milan Tel: 39-0331-742611 Fax: 39-0331-466781 Japan - Tokyo Tel: 81-3-6880- 3770 Fax: 81-3-6880-3771 11/29/12 2001-2012 Microchip Technology Inc.