TC650/TC651 Tiny Integrated Temperature Sensor & Brushless DC Fan Controller with Overtemperature Alert Features General Description • Integrated Temperature Sensing and Multi-speed Fan Control • Built-in Overtemperature Alert (TOVER) • Temperature-proportional Fan Speed Control for Acoustic Noise Reduction and Longer Fan Life • Pulse Width Modulation (PWM) Output Drive for Cost and Power Savings • Solid-state Temperature Sensing • ±1C (typ.) Accuracy from 25C to +70C • Operating Range: 2.8V – 5.5V • TC651 includes Automatic Fan Shutdown • Low Operating Current: 50 µA (typ.) The TC650/TC651 are integrated temperature sensors and brushless DC fan speed controllers. The TC650/ TC651 measure the junction temperature and control the speed of the fan based on that temperature, making them especially suited for applications in modern electronic equipment. Applications • • • • • • Thermal Protection For Personal Computers Digital Set-Top Boxes Notebook Computers Data Communications Power Supplies Projectors Related Literature • Application Note 771 (DS00771) Temperature data is converted from the on-chip thermal sensing element and translated into a fractional fan speed from 40% to 100%. A temperature selection guide in the data sheet is used to choose the low and high temperature limits to control the fan. The TC650/TC651 also include a single trip point overtemperature alert (TOVER) that eliminates the need for additional temperature sensors. In addition, the TC651 features an auto fan shutdown function for additional power savings. The TC650/TC651 are easy to use, require no software overhead and are, therefore, the ideal choice for implementing thermal management in a variety of systems. Package Type 8-Pin MSOP VDD 1 NC 2 SHDN 3 GND 4 2001-2012 Microchip Technology Inc. 8 PWM TC650 TC651 7 GND 6 TOVER 5 NC DS21450D-page 1 TC650/TC651 Typical Application Circuit +12V PIC® Microcontroller +5V VDD SHDN Control DC Fan 500 mA TC650 TC651 1 VDD PWM 8 2 NC GND 7 3 SHDN 4 GND CSLOW TOVER 6 NC 5 GND GND Overtemperature Alert DS21450D-page 2 2001-2012 Microchip Technology Inc. TC650/TC651 1.0 ELECTRICAL CHARACTERISTICS Absolute Maximum Ratings† Input Voltage (VDD to GND) ................................... +6V † Notice: Stresses above those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. These are stress ratings only and functional operation of the device at these or any other conditions above those indicated in the operation sections of the specifications is not implied. Exposure to Absolute Maximum Rating conditions for extended periods may affect device reliability. Output Voltage (OUT to GND) ................................. 6V Voltage On Any Pin ....... (GND – 0.3V) to (VDD + 0.3V) Operating Temperature Range ......... –40C to +125C Storage Temperature ........................ –65C to +150C DC CHARACTERISTICS Electrical Specifications: Unless otherwise specified, VDD = 2.8V to 5.5V, SHDN = VDD, TA = –40C to +125C. Parameters Sym Min Typ Max Units Conditions Supply Voltage VDD 2.8 — 5.5 V Supply Current IDD — 50 90 µA SHDN Input High Threshold VIH 65 — — %VDD SHDN Input Low Threshold VIL — — 15 %VDD PWM Output Low Voltage VOL — — 0.3 V ISINK = 1 mA PWM Output High Voltage VOH VDD – 0.5 — — V ISOURCE = 5 mA PWM Rise Time tR — 10 — µs IOH = 5 mA, 1 nF from PWM to GND PWM Fall Time tF — 10 — µs IOL = 1 mA, 1 nF from PWM to GND fOUT 10 15 — Hz tSTARTUP — 32/fOUT — sec PWM, TOVER are open SHDN Input PWM Output PWM Frequency Start-up Time VDD Rises from GND or SHDN Released Temperature Accuracy High Temperature Accuracy TH ACC TH – 3 TH TH + 3 °C Note 1 –1.0 — +1.0 °C (TH – TL) 20C –2.5 — +2.5 °C (TH – TL) 20C THYST — (TH -TL)/5 — °C TC651 Only TOVER Output High Voltage VHIGH VDD – 0.5 — — V ISOURCE = 1.2 mA TOVER Output Low Voltage VLOW — — 0.4 V ISINK = 2.5 mA Absolute Accuracy TOVER ACC — TH + 10 — °C At Trip Point Trip Point Hysteresis TOVER HYST — 5 — °C Temperature Range Accuracy (TH –TL) ACC Auto-shutdown Hysteresis TOVER Output Note 1: Transition from 90% to 100% Duty Cycle. 2001-2012 Microchip Technology Inc. DS21450D-page 3 TC650/TC651 TEMPERATURE CHARACTERISTICS Electrical Specifications: Unless otherwise noted, VDD = 2.8V to 5.5V, SHDN = VDD, TA = -40C to +125C. Parameters Sym Min Typ Max Units Specified Temperature Range TA –40 — +125 °C Maximum Junction Temperature TJ — — +150 °C Storage Temperature Range TA –65 — +150 °C JA — 206.3 — °C/W Conditions Temperature Ranges Package Thermal Resistances Thermal Resistance, 8L-MSOP DS21450D-page 4 2001-2012 Microchip Technology Inc. TC650/TC651 2.0 TYPICAL PERFORMANCE CURVES Note: The graphs and tables provided following this note are a statistical summary based on a limited number of samples and are provided for informational purposes only. The performance characteristics listed herein are not tested or guaranteed. In some graphs or tables, the data presented may be outside the specified operating range (e.g., outside specified power supply range) and therefore outside the warranted range. Note: Unless otherwise indicated, VDD = 2.8V to 5.5V, SHDN = VDD, TA = –40C to +125C. 90 3.0 80 2.5 VDD = 5.6 60 IDD (µA) Temp Accuracy (°C) 70 50 40 VDD = 2.7 30 20 2.0 1.5 1.0 VDD = 5.6 0.5 10 0.0 0 -50 -25 0 50 25 75 100 125 150 VDD = 2.7 T1 TL T2 FIGURE 2-1: IDD vs. Temperature. FIGURE 2-4: VTH. 500 1.0 450 0.9 400 VDD - VOH (V) VOL (mV) 300 VDD = 5.5V 250 200 150 100 50 0.0 T4 TH Temperature Accuracy vs. 0.8 VDD = 2.8V 350 T3 TTHRESHOLD TEMPERATURE (°C) 0.7 VDD = 2.8V 0.6 VDD = 5.5V 0.5 0.4 0.3 0.2 TA = +25°C 0 1 2 3 4 5 6 7 8 9 10 0.1 0.0 ISINK (mA) FIGURE 2-2: PWM, ISINK vs. VOL. FIGURE 2-5: (VDD – VOH). TA = +25°C 0 2 4 6 8 10 12 14 16 18 20 ISOURCE (mA) PWM, ISOURCE vs. 1.0 0.9 VDD = 2.8V VDD - VOH (V) 0.8 0.7 0.6 VDD = 5.5V 0.5 0.4 0.3 0.2 TA = +25°C 0.1 0.0 0 1 2 3 4 5 6 7 8 9 10 ISOURCE (mA) FIGURE 2-3: (VDD – VOH). TOVER, ISOURCE vs. 2001-2012 Microchip Technology Inc. DS21450D-page 5 TC650/TC651 3.0 PIN DESCRIPTION The descriptions of the pins are listed in Table 3-1. TABLE 3-1: PIN FUNCTION TABLE Pin No. Symbol 1 VDD Power Supply Input 2 NC No Internal Connect 3 SHDN 4 GND 5 NC 6 TOVER 7 GND Ground 8 PWM PWM Fan Drive Output 3.1 Description Fan Shutdown, Active-low Input 1 = Fan in normal operation 0 = Fan in shutdown Ground No Connect Overtemperature Alert, Active-low Output 1 = Overtemperature condition does not exist 0 = The device is in the overtemperature condition. The fan is driven at 100%. Potential exists for system over-heating Power Supply Input 3.4 Overtemperature Alert May be independent of fan power supply. Active-low output. 3.2 3.5 Fan Shutdown, Active-low Input During Shutdown mode, the chip still monitors temperature. TOVER is low if temperature rises above factory set point. 3.3 PWM Fan Drive Output Pulse width modulated rail-to-rail logic output. Nominal frequency is 15 Hz. Ground Ground return for all TC650/TC651 functions. DS21450D-page 6 2001-2012 Microchip Technology Inc. TC650/TC651 4.0 DETAILED DESCRIPTION 4.2 The TC650/TC651 acquire and convert their junction temperature (TJ) information from an on-chip, solidstate sensor with a typical accuracy of ±1°C. The temperature data is digitally stored in an internal register. The register is compared with pre-defined threshold values. The six threshold values are equally distributed over a pre-defined range of temperatures (see Table 41). The TC650/TC651 control the speed of a DC brushless fan using a fractional speed-control scheme. The output stage requires only a 2N2222-type, small-signal BJT for fans up to 300 mA. For larger current fans (up to 1 amp), a logic-level N-channel MOSFET may be used. In addition to controlling the speed of the fan, the TC650/TC651 include an on-chip overtemperature alarm (TOVER) that gives a low signal when the temperature of the chip exceeds TH by 10°C (typical). This feature eliminates the need for a separate temperature sensor for overtemperature monitoring. Figure 4-1 shows the block diagram of the device. TOVER VDD Temperature Set Point and Trim Range V+ SHDN Duty Cycle Logic Control PWM A/D Converter Oscillator Temperature Sensor FIGURE 4-1: 4.1 Functional Block Diagram. PWM Output The PWM pin is designed to drive a low-cost transistor or MOSFET as the low-side, power-switching element in the system. This output has an asymmetric complementary drive and is optimized for driving NPN transistors or N-channel MOSFETs. Since the system relies on PWM rather than linear power control, the dissipation in the power switch is kept to a minimum. Generally, very small devices (TO-92 or SOT packages) will suffice. The frequency of the PWM is about 15 Hz. The PWM is also the time base for the Start-up Timer (see Section 4.2 “Start-Up Timer”). The PWM duty cycle has a range of 40% to 100% for the TC650 and 50% to 100% for the TC651. 2001-2012 Microchip Technology Inc. Start-Up Timer To ensure reliable fan start-up, the Start-up Timer turns PWM high for about 2 seconds whenever the fan is started from the off state. This occurs at power-up and when coming out of Shutdown mode. 4.3 Overtemperature Alert (TOVER) This pin goes low when the TH set point is exceeded by 10°C (typical). This indicates that the fan is at maximum drive and the potential exists for system overheating; either heat dissipation in the system has gone beyond the cooling system's design limits or some fault exists (such as fan bearing failure or an airflow obstruction). This output may be treated as a “System Overheat” warning and be used to either trigger system shutdown or bring other fans in the system to full speed. The fan will continue to run at full speed while TOVER is asserted. Built-in hysteresis prevents TOVER from “chattering” when the measured temperature is at or near the TH + 10°C trip point. As temperature falls through the TH + 10°C trip point, hysteresis maintains the TOVER output low until the measured temperature is 5°C above the trip point setting. 4.4 Shutdown (SHDN) The fan can be unconditionally shut down by pulling the SHDN pin low. During shutdown, the PWM output is low; ideal for notebook computers and other portable applications where you need to change batteries and must not have the fan running at that time. Thermal monitoring and TOVER are still in operation during shutdown. IDD shutdown current is around 50 µA. 4.5 Auto-shutdown Mode The TC651 features auto-shutdown. When the temperature is below the factory set point at minimum speed (TL), PWM is low and the fan is automatically shut off (Auto-shutdown mode). This feature is ideal for notebook computers and other portable equipment that need to conserve as much battery power as possible and, thus, run a fan when it is only absolutely needed. The TC651 will continue to be active in order to monitor temperature for TOVER. The TC651 exits Autoshutdown mode when the temperature rises above the factory set point (T1). DS21450D-page 7 TC650/TC651 4.6 Temperature Selection Guide (Minimum Fan Speed/Full Speed) There are two temperature thresholds that determine the characteristics of the device. The minimum fan speed temperature (TL) and the full fan speed temperature (TH). Depending on the TC65X device selected, when the temperature is below the TL trip point, the PWM output will perform a different operation. For the TC650, the PWM will be driven at the minimum PWM frequency, while the TC651 will shut down the PWM (PWM = L). TL and TH can be selected in 5°C increments. TL can range from 25°C to 35°C. TH can range from 35°C to 55°C and must be 10°C (or more) than the specified TL. The five temperature regions defined by the six thresholds are defined in the TC650/TC651 by means of factory trimming. Once a TL and TH are set, the T1 – T4 thresholds are automatically equally spaced between TL and TH. Table 4-1 shows these 5 regions and what the corresponding PWM duty cycle is. TABLE 4-1: TC650 (Minimum Speed mode) TC651 (Auto-shutdown mode) T < TL 40% Off TL< = T < T1 50% 50% T 1 < = T < T2 60% 60% T2 < = T <T3 70% 70% T 3 < = T < T4 80% 80% T 4 < = T < TH 90% 90% 100% 100% TH < = T < TOV TOV < = T Note 1: Example 1: Suppose you wanted the fan to run at 40% speed at 25°C or less and go to fullspeed at 45°C. You would order the part number TC650AEVUA. Example 2: Suppose you wanted the fan to turn on at 30°C and go to full speed at 45°C. You would order the part number TC651BEVUA. TABLE 4-2: DEVICE CODES FOR TEMPERATURE THRESHOLDS Temp. Threshold Difference TL TH Threshold Limits Code 10°C 25 35 AC (1) 30 40 BD (2) 35 45 CE (2) 25 40 AD (2) 30 45 BE (1) 35 50 CF (2) 25 45 AE (1) 30 50 BF (2) 35 55 CG (1) 25 55 AG (1) TEMPERATURE RANGE DEFINITION PWM Duty Cycle Temperature (T = TJ) (Note 1) Table 4-2 shows the device codes that specify the TH and TL temperature thresholds. The following examples are given to assist in understanding the deviceordering nomenclature. 15°C 20°C 30°C Note 1: 2: This temperature threshold option is available for ordering. This is a custom temperature threshold option. Please contact the factory for more information. 100% with Overtemperature Alert (TOVER = L) The temperature regions defined by the six temperature thresholds are predefined in the TC650/TC651 by means of factory trimming. Once a TL and TH are programmed, the T1 – T4 thresholds are automatically equally spaced between TL and TH. DS21450D-page 8 2001-2012 Microchip Technology Inc. TC650/TC651 5.0 TYPICAL APPLICATIONS 5.1 Reducing Switching Noise For fans consuming more than 300 mA, a slowdown capacitor (CSLOW) is recommended for reducing switching PWM induced noise (see Figure 5-1). The value of this capacitor should be 4.7 µF to 47 µF, depending on the fan current consumption. See Application Note 771, “Suppressing Acoustic Noise in PWM Fan Speed Control Systems” (DS00771), for more information. +12V PIC® Microcontroller +5V VDD SHDN Control DC Fan 500 mA TC650 TC651 1 VDD PWM 8 2 NC GND 7 3 SHDN 4 GND CSLOW TOVER 6 NC 5 GND GND Overtemperature Alert FIGURE 5-1: Reducing Switching Noise. 2001-2012 Microchip Technology Inc. DS21450D-page 9 TC650/TC651 6.0 PACKAGING INFORMATION 6.1 Package Marking Information 8-Lead MSOP XXXXX YWWNNN Legend: XX...X Y YY WW NNN e3 * Note: DS21450D-page 10 Example: 650ACV 406256 Customer-specific information Year code (last digit of calendar year) Year code (last 2 digits of calendar year) Week code (week of January 1 is week ‘01’) Alphanumeric traceability code Pb-free JEDEC designator for Matte Tin (Sn) This package is Pb-free. The Pb-free JEDEC designator ( e3 ) can be found on the outer packaging for this package. In the event the full Microchip part number cannot be marked on one line, it will be carried over to the next line, thus limiting the number of available characters for customer-specific information. 2001-2012 Microchip Technology Inc. TC650/TC651 8-Lead Plastic Micro Small Outline Package (MS) (MSOP) Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging E E1 p D 2 B n 1 α A2 A c φ A1 (F) L β Units Dimension Limits n p MIN INCHES NOM MAX MILLIMETERS* NOM 8 0.65 BSC 0.75 0.85 0.00 4.90 BSC 3.00 BSC 3.00 BSC 0.40 0.60 0.95 REF 0° 0.08 0.22 5° 5° - MIN Number of Pins 8 Pitch .026 BSC A .043 Overall Height A2 Molded Package Thickness .030 .033 .037 A1 Standoff .000 .006 E Overall Width .193 TYP. E1 Molded Package Width .118 BSC D Overall Length .118 BSC L Foot Length .016 .024 .031 Footprint (Reference) F .037 REF φ 0° 8° Foot Angle c Lead Thickness .003 .006 .009 B .009 .012 .016 Lead Width α 5°5° 15° Mold Draft Angle Top β Mold Draft Angle Bottom 5°5° 15° *Controlling Parameter Notes: Dimensions D and E1 do not include mold flash or protrusions. Mold flash or protrusions shall not exceed .010" (0.254mm) per side. MAX 1.10 0.95 0.15 0.80 8° 0.23 0.40 15° 15° JEDEC Equivalent: MO-187 Drawing No. C04-111 2001-2012 Microchip Technology Inc. DS21450D-page 11 TC650/TC651 6.2 Product Tape and Reel Specifications FIGURE 6-1: EMBOSSED CARRIER DIMENSIONS Top Cover Tape A0 W B0 K0 P TABLE 1: CARRIER TAPE/CAVITY DIMENSIONS Case Outline Carrier Dimensions Package Type MS MSOP FIGURE 1: 8L Cavity Dimensions W mm P mm A0 mm B0 mm K0 mm 12 8 5.3 3.6 1.4 Output Quantity Units Reel Diameter in mm 2500 330 MSOP DEVICES User Direction of Feed Pin 1 Pin 1 W, Width of Carrier Tape P, Pitch Standard Reel Component Orientation DS21450D-page 12 Reverse Reel Component Orientation 2001-2012 Microchip Technology Inc. TC650/TC651 7.0 REVISION HISTORY Revision D (December 2012) Added a note to the package outline drawing. 2001-2012 Microchip Technology Inc. DS21450D-page 13 TC650/TC651 NOTES: DS21450D-page 14 2001-2012 Microchip Technology Inc. TC650/TC651 PRODUCT IDENTIFICATION SYSTEM To order or obtain information, e.g., on pricing or delivery, refer to the factory or the listed sales office. PART NO. Device XX X XX Examples: Temperature Temperature Package Threshold Range Limit Device: a) b) TC650: Temp Sensor & Brushless DC Fan Controller / Overtemperature Alert (minimum speed) TC651: Temp Sensor & Brushless DC Fan Controller / Overtemperature Alert (auto shutdown) c) d) e) Temperature Threshold Limit: Temperature Difference TL (1,2) TH (1,3) Threshold Limit Code 10°C 25 30 35 35 40 45 AC BD CE 15°C 25 30 35 40 45 50 AD BE CF 20°C 25 30 35 45 50 55 AE BF CG 30°C 25 55 AG f) g) TC650ACVUA: Temp Sensor TL = 25, TH = 35 TC651ACVUATR: Temp Sensor TL = 25, TH = 35 Tape and Reel TC650AEVUA: Temp Sensor TL = 25, TH = 45 TC651AGVUA: Temp Sensor TL = 25, TH = 55 TC650BEVUA: Temp Sensor TL = 30, TH = 45 TC651CGVUA: Temp Sensor TL = 35, TH = 55 TC650CGVUATR: Temp Sensor TL = 35, TH = 55 Tape and Reel 1. TL and TH can be selected in 5°C increments. 2. TL can range from 25°C to 35°C. 3. TH can range from 35°C to 55°C and must be at least 10°C higher than TL. Temperature Range: V = -40C to +125C (Extended) Package: UA = Plastic Micro Small Outline (MSOP), 8-lead UATR = Plastic Micro Small Outline (MSOP), 8-lead (Tape and Reel) Sales and Support Data Sheets Products supported by a preliminary Data Sheet may have an errata sheet describing minor operational differences and recommended workarounds. To determine if an errata sheet exists for a particular device, please contact one of the following: 1. 2. Your local Microchip sales office The Microchip Worldwide Site (www.microchip.com) Please specify which device, revision of silicon and Data Sheet (include Literature #) you are using. Customer Notification System Register on our web site (www.microchip.com/cn) to receive the most current information on our products. 2001-2012 Microchip Technology Inc. DS21450D-page 15 TC650/TC651 NOTES: DS21450D-page 16 2001-2012 Microchip Technology Inc. Note the following details of the code protection feature on Microchip devices: • Microchip products meet the specification contained in their particular Microchip Data Sheet. • Microchip believes that its family of products is one of the most secure families of its kind on the market today, when used in the intended manner and under normal conditions. • There are dishonest and possibly illegal methods used to breach the code protection feature. All of these methods, to our knowledge, require using the Microchip products in a manner outside the operating specifications contained in Microchip’s Data Sheets. Most likely, the person doing so is engaged in theft of intellectual property. • Microchip is willing to work with the customer who is concerned about the integrity of their code. • Neither Microchip nor any other semiconductor manufacturer can guarantee the security of their code. Code protection does not mean that we are guaranteeing the product as “unbreakable.” Code protection is constantly evolving. We at Microchip are committed to continuously improving the code protection features of our products. Attempts to break Microchip’s code protection feature may be a violation of the Digital Millennium Copyright Act. If such acts allow unauthorized access to your software or other copyrighted work, you may have a right to sue for relief under that Act. Information contained in this publication regarding device applications and the like is provided only for your convenience and may be superseded by updates. It is your responsibility to ensure that your application meets with your specifications. MICROCHIP MAKES NO REPRESENTATIONS OR WARRANTIES OF ANY KIND WHETHER EXPRESS OR IMPLIED, WRITTEN OR ORAL, STATUTORY OR OTHERWISE, RELATED TO THE INFORMATION, INCLUDING BUT NOT LIMITED TO ITS CONDITION, QUALITY, PERFORMANCE, MERCHANTABILITY OR FITNESS FOR PURPOSE. Microchip disclaims all liability arising from this information and its use. Use of Microchip devices in life support and/or safety applications is entirely at the buyer’s risk, and the buyer agrees to defend, indemnify and hold harmless Microchip from any and all damages, claims, suits, or expenses resulting from such use. No licenses are conveyed, implicitly or otherwise, under any Microchip intellectual property rights. Trademarks The Microchip name and logo, the Microchip logo, dsPIC, FlashFlex, KEELOQ, KEELOQ logo, MPLAB, PIC, PICmicro, PICSTART, PIC32 logo, rfPIC, SST, SST Logo, SuperFlash and UNI/O are registered trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. FilterLab, Hampshire, HI-TECH C, Linear Active Thermistor, MTP, SEEVAL and The Embedded Control Solutions Company are registered trademarks of Microchip Technology Incorporated in the U.S.A. Silicon Storage Technology is a registered trademark of Microchip Technology Inc. in other countries. Analog-for-the-Digital Age, Application Maestro, BodyCom, chipKIT, chipKIT logo, CodeGuard, dsPICDEM, dsPICDEM.net, dsPICworks, dsSPEAK, ECAN, ECONOMONITOR, FanSense, HI-TIDE, In-Circuit Serial Programming, ICSP, Mindi, MiWi, MPASM, MPF, MPLAB Certified logo, MPLIB, MPLINK, mTouch, Omniscient Code Generation, PICC, PICC-18, PICDEM, PICDEM.net, PICkit, PICtail, REAL ICE, rfLAB, Select Mode, SQI, Serial Quad I/O, Total Endurance, TSHARC, UniWinDriver, WiperLock, ZENA and Z-Scale are trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. SQTP is a service mark of Microchip Technology Incorporated in the U.S.A. GestIC and ULPP are registered trademarks of Microchip Technology Germany II GmbH & Co. & KG, a subsidiary of Microchip Technology Inc., in other countries. All other trademarks mentioned herein are property of their respective companies. © 2001-2012, Microchip Technology Incorporated, Printed in the U.S.A., All Rights Reserved. Printed on recycled paper. ISBN: 9781620768310 QUALITY MANAGEMENT SYSTEM CERTIFIED BY DNV == ISO/TS 16949 == 2001-2012 Microchip Technology Inc. Microchip received ISO/TS-16949:2009 certification for its worldwide headquarters, design and wafer fabrication facilities in Chandler and Tempe, Arizona; Gresham, Oregon and design centers in California and India. The Company’s quality system processes and procedures are for its PIC® MCUs and dsPIC® DSCs, KEELOQ® code hopping devices, Serial EEPROMs, microperipherals, nonvolatile memory and analog products. In addition, Microchip’s quality system for the design and manufacture of development systems is ISO 9001:2000 certified. DS21450D-page 17 Worldwide Sales and Service AMERICAS ASIA/PACIFIC ASIA/PACIFIC EUROPE Corporate Office 2355 West Chandler Blvd. Chandler, AZ 85224-6199 Tel: 480-792-7200 Fax: 480-792-7277 Technical Support: http://www.microchip.com/ support Web Address: www.microchip.com Asia Pacific Office Suites 3707-14, 37th Floor Tower 6, The Gateway Harbour City, Kowloon Hong Kong Tel: 852-2401-1200 Fax: 852-2401-3431 India - Bangalore Tel: 91-80-3090-4444 Fax: 91-80-3090-4123 India - New Delhi Tel: 91-11-4160-8631 Fax: 91-11-4160-8632 Austria - Wels Tel: 43-7242-2244-39 Fax: 43-7242-2244-393 Denmark - Copenhagen Tel: 45-4450-2828 Fax: 45-4485-2829 India - Pune Tel: 91-20-2566-1512 Fax: 91-20-2566-1513 France - Paris Tel: 33-1-69-53-63-20 Fax: 33-1-69-30-90-79 Japan - Osaka Tel: 81-6-6152-7160 Fax: 81-6-6152-9310 Germany - Munich Tel: 49-89-627-144-0 Fax: 49-89-627-144-44 Atlanta Duluth, GA Tel: 678-957-9614 Fax: 678-957-1455 Boston Westborough, MA Tel: 774-760-0087 Fax: 774-760-0088 Chicago Itasca, IL Tel: 630-285-0071 Fax: 630-285-0075 Cleveland Independence, OH Tel: 216-447-0464 Fax: 216-447-0643 Dallas Addison, TX Tel: 972-818-7423 Fax: 972-818-2924 Detroit Farmington Hills, MI Tel: 248-538-2250 Fax: 248-538-2260 Indianapolis Noblesville, IN Tel: 317-773-8323 Fax: 317-773-5453 Los Angeles Mission Viejo, CA Tel: 949-462-9523 Fax: 949-462-9608 Santa Clara Santa Clara, CA Tel: 408-961-6444 Fax: 408-961-6445 Toronto Mississauga, Ontario, Canada Tel: 905-673-0699 Fax: 905-673-6509 Australia - Sydney Tel: 61-2-9868-6733 Fax: 61-2-9868-6755 China - Beijing Tel: 86-10-8569-7000 Fax: 86-10-8528-2104 China - Chengdu Tel: 86-28-8665-5511 Fax: 86-28-8665-7889 China - Chongqing Tel: 86-23-8980-9588 Fax: 86-23-8980-9500 Netherlands - Drunen Tel: 31-416-690399 Fax: 31-416-690340 Korea - Daegu Tel: 82-53-744-4301 Fax: 82-53-744-4302 Spain - Madrid Tel: 34-91-708-08-90 Fax: 34-91-708-08-91 China - Hangzhou Tel: 86-571-2819-3187 Fax: 86-571-2819-3189 Korea - Seoul Tel: 82-2-554-7200 Fax: 82-2-558-5932 or 82-2-558-5934 China - Hong Kong SAR Tel: 852-2943-5100 Fax: 852-2401-3431 Malaysia - Kuala Lumpur Tel: 60-3-6201-9857 Fax: 60-3-6201-9859 China - Nanjing Tel: 86-25-8473-2460 Fax: 86-25-8473-2470 Malaysia - Penang Tel: 60-4-227-8870 Fax: 60-4-227-4068 China - Qingdao Tel: 86-532-8502-7355 Fax: 86-532-8502-7205 Philippines - Manila Tel: 63-2-634-9065 Fax: 63-2-634-9069 China - Shanghai Tel: 86-21-5407-5533 Fax: 86-21-5407-5066 Singapore Tel: 65-6334-8870 Fax: 65-6334-8850 China - Shenyang Tel: 86-24-2334-2829 Fax: 86-24-2334-2393 Taiwan - Hsin Chu Tel: 886-3-5778-366 Fax: 886-3-5770-955 China - Shenzhen Tel: 86-755-8864-2200 Fax: 86-755-8203-1760 Taiwan - Kaohsiung Tel: 886-7-213-7828 Fax: 886-7-330-9305 China - Wuhan Tel: 86-27-5980-5300 Fax: 86-27-5980-5118 Taiwan - Taipei Tel: 886-2-2508-8600 Fax: 886-2-2508-0102 China - Xian Tel: 86-29-8833-7252 Fax: 86-29-8833-7256 Thailand - Bangkok Tel: 66-2-694-1351 Fax: 66-2-694-1350 UK - Wokingham Tel: 44-118-921-5869 Fax: 44-118-921-5820 China - Xiamen Tel: 86-592-2388138 Fax: 86-592-2388130 China - Zhuhai Tel: 86-756-3210040 Fax: 86-756-3210049 DS21450D-page 18 Italy - Milan Tel: 39-0331-742611 Fax: 39-0331-466781 Japan - Tokyo Tel: 81-3-6880- 3770 Fax: 81-3-6880-3771 11/29/12 2001-2012 Microchip Technology Inc.