Metallized Polypropylene Film Capacitors (MKP) B 32 620 Plastic Case B 32 621 MKP stacked-film capacitors Smallest possible dimensions Construction ■ ■ ■ ■ Dielectric: polypropylene Stacked-film technology Plastic case (UL 94 V-0) Epoxy resin sealing Features ■ ■ ■ ■ Very high pulse strength Very good self-healing properties Smallest possible dimensions High contact reliability Dimensions in mm Lead spacing ± 0,4 Typical applications ■ ■ ■ ■ 7,5 Energy-saving lamps TV S-correction High pulse load applications AC applications 10 Diameter d1 Type 0,5 B 32 620 0,51)/0,6 B 32 621 1) 0,5 mm for capacitor width b = 4 mm Terminals ■ Parallel wire leads, tinned ■ Also available with (3,2 ± 0,3) mm lead length Marking Manufacturer’s logo, lot number, style and type (P621) for lead spacing 10 mm, style (MKP) for lead spacing 7,5 mm, rated capacitance (coded), capacitance tolerance (code letter), rated dc voltage, date of manufacture (coded) Delivery mode Bulk (untaped) Taped (Ammo pack or reel) For notes on taping, refer to chapter “Taping and packing”, page 274. 117 12/00 MKP B 32 620 B 32 621 Overview of available types 10 mm 119 121 118 12/00 630 Vdc 400 Vac 400 Vdc 200 Vac 250 Vdc 140 Vac 160 Vdc 90 Vac 250 Vdc 140 Vac 160 Vdc 90 Vac 400 Vdc 200 Vac 1000 Vdc 600 Vac B 32 621 Page 0,47 nF 0,68 nF 1,0 nF 1,5 nF 2,2 nF 3,3 nF 4,7 nF 6,8 nF 10 nF 15 nF 22 nF 33 nF 47 nF 68 nF 0,10 µF 0,15 µF 0,22 µF 1000 Vdc 500 Vac B 32 620 630 Vdc 400 Vac Type 1000 Vdc 500 Vac Lead spacing 7,5 mm B 32 620 MKP 7,5 Ordering codes and packing units, lead spacing 7,5 mm VR (Vrms f ≤ 1 kHz) CR 160 Vdc (90 Vac) 22 nF 33 nF 47 nF 68 nF 0,10 µF 0,15 µF 22 nF 33 nF 47 nF 68 nF 0,10 µF 6,8 nF 10 nF 15 nF 22 nF 33 nF 1,5 nF 2,2 nF 3,3 nF 4,7 nF 6,8 nF 10 nF 15 nF 250 Vdc (140 Vac) 400 Vdc (200 Vac) 630 Vdc (400 Vac) Maximum dimensions b × h × l (mm) Ordering code1) Packing units (pcs) 3,0 × 8,0 × 10,0 4,0 × 8,5 × 10,0 4,0 × 8,5 × 10,0 5,0 × 10,5 × 10,0 5,0 × 10,5 × 10,0 6,0 × 12,0 × 10,3 4,0 × 8,5 × 10,0 4,0 × 8,5 × 10,0 5,0 × 10,5 × 10,0 5,0 × 10,5 × 10,0 6,0 × 12,0 × 10,3 4,0 × 8,5 × 10,0 4,0 × 8,5 × 10,0 5,0 × 10,5 × 10,0 5,0 × 10,5 × 10,0 6,0 × 12,0 × 10,3 4,0 × 8,5 × 10,0 4,0 × 8,5 × 10,0 4,0 × 8,5 × 10,0 4,0 × 8,5 × 10,0 5,0 × 10,5 × 10,0 5,0 × 10,5 × 10,0 6,0 × 12,0 × 10,3 B32620-A5223-+*** B32620-A5333-+*** B32620-A5473-+*** B32620-A5683-+*** B32620-A5104-+*** B32620-A5154-+*** B32620-A3223-+*** B32620-A3333-+*** B32620-A3473-+*** B32620-A3683-+*** B32620-A3104-+*** B32620-A4682-+*** B32620-A4103-+*** B32620-A4153-+*** B32620-A4223-+*** B32620-A4333-+*** B32620-A6152-+*** B32620-A6222-+*** B32620-A6332-+*** B32620-A6472-+*** B32620-A6682-+*** B32620-A6103-+*** B32620-A6153-+*** Ammo pack 2600 2000 2000 1600 1600 1300 2000 2000 1600 1600 1300 2000 2000 1600 1600 1300 2000 2000 2000 2000 1600 1600 1300 Reel Untaped 2400 1800 1800 1400 1400 1100 1800 1800 1400 1400 1100 1800 1800 1400 1400 1100 1800 1800 1800 1800 1400 1400 1100 2000 1500 1500 1000 1000 750 1500 1500 1000 1000 750 1500 1500 1000 1000 750 1500 1500 1500 1500 1000 1000 750 Capacitance tolerance: ± 20 % =ˆ M, ± 10 % =ˆ K, ± 5 % =ˆ J 1) + Code letter for capacitance tolerance *** Code number for packing: Ammo pack = 289, reel = 189 The ordering code for untaped components ends after the tolerance code letter. For capacitors with 3,2 mm lead length, append code number “3” to the tolerance code, e.g.: B32620-A5104-K3 119 12/00 MKP B 32 620 7,5 Ordering codes and packing units, lead spacing 7,5 mm VR (Vrms f ≤ 1 kHz) CR 1000 Vdc (500 Vac) 1,5 nF 2,2 nF 3,3 nF 4,7 nF 6,8 nF 470 pF 680 pF 1,0 nF 1,5 nF 2,2 nF 3,3 nF 4,7 nF 1000 Vdc (600 Vac) Maximum dimensions b × h × l (mm) Ordering code1) Packing units (pcs) 4,0 × 8,5 × 10,0 4,0 × 8,5 × 10,0 5,0 × 10,5 × 10,0 5,0 × 10,5 × 10,0 6,0 × 12,0 × 10,3 4,0 × 8,5 × 10,0 5,0 × 10,5 × 10,0 5,0 × 10,5 × 10,0 5,0 × 10,5 × 10,0 5,0 × 10,5 × 10,0 5,0 × 10,5 × 10,0 6,0 × 12,0 × 10,3 B32620-A152-+*** B32620-A222-+*** B32620-A332-+*** B32620-A472-+*** B32620-A682-+*** B32620-J471-+*** B32620-J681-+*** B32620-J102-+*** B32620-J152-+*** B32620-J222-+*** B32620-J332-+*** B32620-J472-+*** Ammo pack 2000 2000 1600 1600 1300 2000 1600 1600 1600 1600 1600 1300 Reel Untaped 1800 1800 1400 1400 1100 1800 1400 1400 1400 1400 1400 1100 1500 1500 1000 1000 750 1500 1000 1000 1000 1000 1000 750 Capacitance tolerance: ± 20 % =ˆ M, ± 10 % =ˆ K, ± 5 % =ˆ J 1) + Code letter for capacitance tolerance *** Code number for packing: Ammo pack = 289, reel = 189 The ordering code for untaped components ends after the tolerance code letter. For capacitors with 3,2 mm lead length, append code number “3” to the tolerance code, e.g.: B32620-A152-K3 120 12/00 B 32 621 MKP 10 Ordering codes and packing units, lead spacing 10 mm VR (Vrms f ≤ 1 kHz) CR 160 Vdc (90 Vac) 47 nF 68 nF 0,10 µF 0,15 µF 0,22 µF 2,2 nF 3,3 nF 4,7 nF 6,8 nF 10 nF 15 nF 22 nF 33 nF 47 nF 68 nF 0,10 µF 10 nF 15 nF 22 nF 33 nF 47 nF 2,2 nF 3,3 nF 4,7 nF 6,8 nF 10 nF 15 nF 22 nF 33 nF 2,2 nF 3,3 nF 4,7 nF 6,8 nF 10 nF 250 Vdc (140 Vac) 400 Vdc (200 Vac) 630 Vdc (400 Vac) 1000 Vdc (500 Vac) Maximum dimensions b × h × l (mm) Ordering code1) Packing units (pcs) 4,0 × 7,0 × 13,0 4,0 × 9,0 × 13,0 5,0 × 11,0 × 13,0 5,0 × 11,0 × 13,0 6,0 × 12,0 × 13,0 4,0 × 7,0 × 13,0 4,0 × 9,0 × 13,0 4,0 × 9,0 × 13,0 4,0 × 9,0 × 13,0 4,0 × 9,0 × 13,0 4,0 × 9,0 × 13,0 4,0 × 9,0 × 13,0 4,0 × 9,0 × 13,0 4,0 × 9,0 × 13,0 5,0 × 11,0 × 13,0 6,0 × 12,0 × 13,0 4,0 × 9,0 × 13,0 4,0 × 9,0 × 13,0 5,0 × 11,0 × 13,0 5,0 × 11,0 × 13,0 6,0 × 12,0 × 13,0 4,0 × 7,0 × 13,0 4,0 × 9,0 × 13,0 4,0 × 9,0 × 13,0 4,0 × 9,0 × 13,0 4,0 × 9,0 × 13,0 5,0 × 11,0 × 13,0 6,0 × 12,0 × 13,0 6,0 × 12,0 × 13,0 4,0 × 7,0 × 13,0 4,0 × 9,0 × 13,0 4,0 × 9,0 × 13,0 5,0 × 11,0 × 13,0 6,0 × 12,0 × 13,0 B32621-A5473-+*** B32621-A5683-+*** B32621-A5104-+*** B32621-A5154-+*** B32621-A5224-+*** B32621-A3222-+*** B32621-A3332-+*** B32621-A3472-+*** B32621-A3682-+*** B32621-A3103-+*** B32621-A3153-+*** B32621-A3223-+*** B32621-A3333-+*** B32621-A3473-+*** B32621-A3683-+*** B32621-A3104-+*** B32621-A4103-+*** B32621-A4153-+*** B32621-A4223-+*** B32621-A4333-+*** B32621-A4473-+*** B32621-A6222-+*** B32621-A6332-+*** B32621-A6472-+*** B32621-A6682-+*** B32621-A6103-+*** B32621-A6153-+*** B32621-A6223-+*** B32621-A6333-+*** B32621-A222-+*** B32621-A332-+*** B32621-A472-+*** B32621-A682-+*** B32621-A103-+*** Ammo pack 1000 1000 830 830 680 1000 1000 1000 1000 1000 1000 1000 1000 1000 830 680 1000 1000 830 830 680 1000 1000 1000 1000 1000 830 680 680 1000 1000 1000 830 680 Reel Untaped 1700 1700 1300 1300 1100 1700 1700 1700 1700 1700 1700 1700 1700 1700 1300 1100 1700 1700 1300 1300 1100 1700 1700 1700 1700 1700 1300 1100 1100 1700 1700 1700 1300 1100 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 Capacitance tolerance: ± 20 % =ˆ M, ± 10 % =ˆ K, ± 5 % =ˆ J 1) + Code letter for capacitance tolerance *** Code number for packing: Ammo pack = 289, reel = 189 The ordering code for untaped components ends after the tolerance code letter. For capacitors with 3,2 mm lead length, append code number “3” to the tolerance code, e.g.: B32621-A5473-K3 121 12/00 MKP B 32 620 B 32 621 Technical data Climatic category in accordance with IEC 60068-1 55/100/56 Lower category temperature Tmin Upper category temperature Tmax − 55 °C + 100 °C Damp heat test 56 days/40 °C/93 % relative humidity Limit values after damp heat test Capacitance change |∆C/C| ≤3% Dissipation factor change ∆ tan δ ≤ 0,5 ⋅ 10−3 (at 1 kHz) ≤ 1,0 ⋅ 10−3 (at 10 kHz) Insulation resistance Ris ≥ 50 % of minimum as-delivered values Reliability: Reference conditions Failure rate 0,5 ⋅ V R; 40 °C 1 ⋅ 10−9/h = 1 fit For a conversion table for other operating conditions and temperatures, refer to chapter “Quality assurance”, page 327. Service life Failure criteria: Total failure Failure due to variation of parameters 200 000 h Short circuit or open circuit Capacitance change |∆C/C| Dissipation factor tan δ Insulation resistance Ris > ±10 % 4 ⋅ upper limit values < 1500 MΩ DC test voltage 1,6 ⋅ V R, 2 s Category voltage VC Operation with dc voltage or ac voltage Vrms up to 1 kHz T ≤ 85 °C: VC = 1,0 ⋅ V R or 1,0 ⋅ V rms T = 100 °C: VC = 0,7 ⋅ V R or 0,7 ⋅ V rms Dissipation factor tan δ (in 10−3) at 20 °C (upper limit values) Insulation resistance R is or time constant τ = CR ⋅ Ris at 20 °C, rel. humidity ≤ 65 % (minimum as-delivered values) at 1 kHz 10 kHz 100 kHz CR ≤ 0,1 µF 0,1 µF < CR ≤ 0,22 µF – – 4,0 1,0 1,5 – 100 GΩ 122 12/00 B 32 620 MKP B 32 621 Impedance Z versus frequency f (typical values) KMK0680-7 10 4 mΩ Z 10 3 5 F 7n 0,4 nF 1,5,2 nF 2 10 2 10 5 10 5 5 10 6 nF 10 1 10 4 nF 33 F 0µ 0,1 2 µF 0,2 5 5 10 7 Hz 10 8 f Pulse handling capability Maximum permissible voltage change per unit of time for non-sinusoidal voltages (pulse, sawtooth) VR Max. rate of voltage rise V pp/τ in V/µs (for V pp = V R) Lead spacing 7,5 mm 10 mm 160 Vdc 750 600 250 Vdc 1200 900 400 Vdc 1500 1050 630 Vdc 2700 1800 1000 Vdc (500 Vac) 3200 2400 1000 Vdc (600 Vac) 4000 − For V pp < V R , the permissible voltage rise rate value V pp/τ may be multiplied by the factor V R/V pp. Also refer to the calculation example in chapter “General technical information”, page 302. VR Pulse characteristic k0 in V2/µs (forVpp ≤ V R) Lead spacing 7,5 mm 10 mm 160 Vdc 240 000 190 000 250 Vdc 600 000 450 000 400 Vdc 1 200 000 840 000 630 Vdc 3 400 000 2 250 000 1000 Vdc (500 Vac) 6 400 000 4 800 000 1000 Vdc (600 Vac) 8 000 000 − 123 12/00 MKP B 32 620 7,5 Permissible ac voltage V rms versus frequency f Lead spacing 7,5 mm 160 Vdc / 90 Vac 250 Vdc / 140 Vac KMK0744-H 1000 Vac Vrms Vrms 500 500 100 100 50 50 22 nF 0,1 µF 0,15 µF 10 2 10 10 3 10 4 10 5 22 nF 0,10 µF 10 3 10 4 10 5 Hz 10 6 f 630 Vdc / 400 Vac KMK0554-C 1000 Vac KMK0553-4 1000 Vac Vrms 500 500 100 100 6,8 nF 15 nF 33 nF 50 10 10 2 10 10 2 Hz 10 6 f 400 Vdc / 200 Vac Vrms KMK0550-E 1000 Vac 10 3 10 4 1,5 nF 3,3 nF 6,8 nF 15 nF 50 10 5 Hz 10 6 f 10 10 2 124 12/00 10 3 10 4 10 5 Hz 10 6 f B 32 620 MKP 7,5 Permissible ac voltage V rms versus frequency f Lead spacing 7,5 mm 1000 Vdc/ 500 Vac 1000 Vdc/ 600 Vac KMK0560-L 1000 Vac Vrms Vrms 500 KMK0651-T 1000 Vac 500 0,47 nF 1,0 nF 2,2 nF 4,7 nF 1,5 nF 6,8 nF 100 100 50 50 10 10 2 10 3 10 4 10 5 Hz 10 6 f 10 10 2 125 12/00 10 3 10 4 10 5 Hz 10 6 f MKP B 32 621 10 Permissible ac voltage V rms versus frequency f Lead spacing 10 mm 160 Vdc / 90 Vac Vrms 250 Vdc / 140 Vac KMK0715-4 400 Vac 200 Vrms 100 60 40 20 10 100 60 40 folgt fol 20 47 nF 0,10 µF 0,22 µF 10 6 4 6 4 2 2 1 2 10 10 3 10 4 10 5 KMK0552-V 10 3 10 4 10 5 Hz 10 6 f KMK0703-F 1000 Vac Vrms 500 500 100 100 10 10 2 2,2 nF 15 nF 0,10 µF 630 Vdc / 400 Vac 1000 Vac 50 1 2 10 Hz 10 6 f 400 Vdc / 200 Vac Vrms KMK0716-C 400 Vac 200 10 nF 47 nF 10 3 50 10 4 10 5 Hz 10 6 f 10 10 2 126 12/00 2,2 nF 15 nF 33 nF 10 3 10 4 10 5 Hz 10 6 f B 32 621 MKP 10 Permissible ac voltage V rms versus frequency f Lead spacing 10 mm 1000 Vdc / 500 Vac KMK0551-M 1000 Vac V ac Vrms 500 100 50 10 10 2 2,2 nF 10 nF 10 3 10 4 10 5 Hz 10 6 f 127 12/00 MKP B 32 620 B 32 621 Sinus-wave application, lighting Permissible voltage and current / waveform Vpp V0-p t = 10 ... 63,5 µs Ipp KMK0721-D 128 12/00 B 32 620 MKP 7,5 Sinus-wave application, lighting Permissible current Ipp versus rated capacaitance C R Lead spacing 7,5 mm 160 Vdc/90 Vac 250 Vdc/140 Vac KMK0681-F 0,4 A pp 100 kHz I pp KMK0640-D 1,6 A pp I pp 1,4 100 kHz 1,2 0,3 0,25 1,0 50 kHz 50 kHz 0,2 0,8 0,15 0,6 0,1 0,4 0,05 0,2 0 0 50 100 0 nF 150 C 400 Vdc/200 Vac 0 20 40 60 nF C 80 630 Vdc/400 Vac KMK0641-L 0,8 A pp I pp 0,7 KMK0642-U 0,6 A pp I pp 0,5 100 kHz 0,6 100 kHz 0,4 0,5 50 kHz 0,4 0,3 50 kHz 0,3 0,2 0,2 0,1 0,1 0 0 10 20 30 nF C 40 0 0 129 12/00 5 10 15 nF C 20 B 32 620 MKP B 32 621 7,5 10 Sinus-wave application, lighting Permissible current Ipp versus rated capacaitance C R Lead spacing 7,5 mm 1000 Vdc/500 Vac 1000 Vdc/600 Vac KMK0643-3 0,3 A pp I pp KMK0644-B 0,4 A pp I pp 100 kHz 100 kHz 0,3 0,2 0,25 50 kHz 50 kHz 0,15 0,2 0,15 0,1 0,1 0,05 0,05 0 1 2 3 4 nF C 0 5 1 2 3 4 nF C 5 Lead spacing 10 mm 160 Vdc/90 Vac 250 Vdc/140 Vac KMK0653-A 0,8 A pp KMK0654-I 0,6 A pp I pp 0,7 I pp 100 kHz 100 kHz 0,5 0,6 50 kHz 0,4 0,5 50 kHz 0,4 0,3 0,3 0,2 0,2 0,1 0,1 0 0 50 100 150 200 nF 250 C 0 0 50 100 nF 150 C 130 12/00 B 32 621 MKP 10 Sinus-wave application, lighting Permissible current Ipp versus rated capacaitance C R Lead spacing 10 mm 400 Vdc/200 Vac 630 Vdc/400 Vac KMK0645-J 1,4 A pp KMK0655-F 0,4 A pp I pp I pp 1,2 100 kHz 0,3 1,0 100 kHz 50 kHz 0,8 0,2 0,6 50 kHz 0,4 0,1 0,2 0 0 10 20 30 40 nF 50 C 0 0 I pp KMK0646-S 100 kHz 0,5 50 kHz 0,4 0,3 0,2 0,1 0 0 2 4 6 8 20 nF 30 C 1000 Vdc/500 Vac 0,6 A pp 10 10 nF 12 C 131 12/00 Herausgegeben von EPCOS AG Marketing Kommunikation, Postfach 80 17 09, 81617 München, DEUTSCHLAND EPCOS AG 2000. Alle Rechte vorbehalten. Vervielfältigung, Veröffentlichung, Verbreitung und Verwertung dieser Broschüre und ihres Inhalts ohne ausdrückliche Genehmigung der EPCOS AG nicht gestattet. Mit den Angaben in dieser Broschüre werden die Bauelemente spezifiziert, keine Eigenschaften zugesichert. Bestellungen unterliegen den vom ZVEI empfohlenen Allgemeinen Lieferbedingungen für Erzeugnisse und Leistungen der Elektroindustrie, soweit nichts anderes vereinbart wird. Diese Broschüre ersetzt die vorige Ausgabe. Fragen über Technik, Preise und Liefermöglichkeiten richten Sie bitte an den Ihnen nächstgelegenen Vertrieb der EPCOS AG oder an unsere Vertriebsgesellschaften im Ausland. Bauelemente können aufgrund technischer Erfordernisse Gefahrstoffe enthalten. Auskünfte darüber bitten wir unter Angabe des betreffenden Typs ebenfalls über die zuständige Vertriebsgesellschaft einzuholen. Published by EPCOS AG Marketing Communications, P.O. Box 80 17 09, 81617 Munich, GERMANY EPCOS AG 2000. All Rights Reserved. Reproduction, publication and dissemination of this brochure and the information contained therein without EPCOS’ prior express consent is prohibited. The information contained in this brochure describes the type of component and shall not be considered as guaranteed characteristics. Purchase orders are subject to the General Conditions for the Supply of Products and Services of the Electrical and Electronics Industry recommended by the ZVEI (German Electrical and Electronic Manufacturers’ Association), unless otherwise agreed. This brochure replaces the previous edition. For questions on technology, prices and delivery please contact the Sales Offices of EPCOS AG or the international Representatives. Due to technical requirements components may contain dangerous substances. For information on the type in question please also contact one of our Sales Offices. 1