SN54AHC240, SN74AHC240 OCTAL BUFFERS/DRIVERS WITH 3-STATE OUTPUTS SCLS251H – OCTOBER 1995 – REVISED JULY 2003 SN54AHC240 . . . J OR W PACKAGE SN74AHC240 . . . DB, DGV, DW, N, NS, OR PW PACKAGE (TOP VIEW) Operating Range 2-V to 5.5-V VCC Latch-Up Performance Exceeds 250 mA Per JESD 17 1OE 1A1 2Y4 1A2 2Y3 1A3 2Y2 1A4 2Y1 GND description/ordering information These octal buffers/drivers are designed specifically to improve the performance and density of 3-state memory-address drivers, clock drivers, and bus-oriented receivers and transmitters. The ’AHC240 devices are organized as two 4-bit buffers/line drivers with separate output-enable (OE) inputs. When OE is low, the device passes data from the A inputs to the Y outputs. When OE is high, the outputs are in the high-impedance state. 1 20 2 19 3 18 4 17 5 16 6 15 7 14 8 13 9 12 10 11 VCC 2OE 1Y1 2A4 1Y2 2A3 1Y3 2A2 1Y4 2A1 2Y4 1A1 1OE VCC SN54AHC240 . . . FK PACKAGE (TOP VIEW) To ensure the high-impedance state during power up or power down, OE should be tied to VCC through a pullup resistor; the minimum value of the resistor is determined by the current-sinking capability of the driver. 4 3 2 1 20 19 18 5 17 6 16 7 15 8 14 9 10 11 12 13 1Y1 2A4 1Y2 2A3 1Y3 2Y1 GND 2A1 1Y4 2A2 1A2 2Y3 1A3 2Y2 1A4 2OE D D ORDERING INFORMATION PDIP – N SN74AHC240N Tube SN74AHC240DW Tape and reel SN74AHC240DWR SOP – NS Tape and reel SN74AHC240NSR AHC240 SSOP – DB Tape and reel SN74AHC240DBR HA240 Tube SN74AHC240PW Tape and reel SN74AHC240PWR TSSOP – PW –55°C to 125°C TOP-SIDE MARKING Tube SOIC – DW –40°C to 85°C ORDERABLE PART NUMBER PACKAGE† TA SN74AHC240N AHC240 HA240 TVSOP – DGV Tape and reel SN74AHC240DGVR HA240 CDIP – J Tube SNJ54AHC240J SNJ54AHC240J CFP – W Tube SNJ54AHC240W SNJ54AHC240W LCCC – FK Tube SNJ54AHC240FK SNJ54AHC240FK † Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines are available at www.ti.com/sc/package. Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. Copyright 2003, Texas Instruments Incorporated PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. On products compliant to MIL-PRF-38535, all parameters are tested unless otherwise noted. On all other products, production processing does not necessarily include testing of all parameters. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 1 SN54AHC240, SN74AHC240 OCTAL BUFFERS/DRIVERS WITH 3-STATE OUTPUTS SCLS251H – OCTOBER 1995 – REVISED JULY 2003 FUNCTION TABLE (each 4-bit buffer/driver) INPUTS OUTPUT Y OE A L H L L L H H X Z logic diagram (positive logic) 1OE 1A1 1A2 1A3 1A4 1 2OE 2 18 4 16 6 14 8 12 1Y1 2A1 1Y2 2A2 1Y3 2A3 1Y4 2A4 19 11 9 13 7 15 5 17 3 2Y1 2Y2 2Y3 2Y4 absolute maximum ratings over operating free-air temperature range (unless otherwise noted)† Supply voltage range, VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to 7 V Input voltage range, VI (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to 7 V Output voltage range, VO (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to VCC + 0.5 V Input clamp current, IIK (VI < 0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –20 mA Output clamp current, IOK (VO < 0 or VO > VCC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±20 mA Continuous output current, IO (VO = 0 to VCC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±25 mA Continuous current through VCC or GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±75 mA Package thermal impedance, θJA (see Note 2): DB package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70°C/W DGV package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92°C/W DW package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58°C/W N package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69°C/W NS package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60°C/W PW package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83°C/W Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –65°C to 150°C † Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. NOTES: 1. The input and output voltage ratings may be exceeded if the input and output current ratings are observed. 2. The package thermal impedance is calculated in accordance with JESD 51-7. 2 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 SN54AHC240, SN74AHC240 OCTAL BUFFERS/DRIVERS WITH 3-STATE OUTPUTS SCLS251H – OCTOBER 1995 – REVISED JULY 2003 recommended operating conditions (see Note 3) SN54AHC240 VCC Supply voltage VIH VCC = 2 V VCC = 3 V High-level input voltage Low-level input voltage VI VO 2 5.5 Output voltage ∆t/∆v 5.5 2.1 V V 0.5 0.9 0.9 1.65 1.65 V 0 5.5 0 5.5 V 0 VCC –50 0 VCC –50 mA VCC = 3.3 V ± 0.3 V VCC = 5 V ± 0.5 V VCC = 3.3 V ± 0.3 V Input transition rise or fall rate 2 UNIT 1.5 3.85 VCC = 2 V VCC = 3.3 V ± 0.3 V Low-level output current MAX 2.1 VCC = 5 V ± 0.5 V VCC = 2 V IOL MIN 3.85 VCC = 3 V VCC = 5.5 V High-level output current SN74AHC240 0.5 Input voltage IOH MAX 1.5 VCC = 5.5 V VCC = 2 V VIL MIN VCC = 5 V ± 0.5 V –4 –4 –8 –8 50 50 4 4 8 8 100 100 20 20 V mA mA mA ns/V TA Operating free-air temperature –55 125 –40 85 °C NOTE 3: All unused inputs of the device must be held at VCC or GND to ensure proper device operation. Refer to the TI application report, Implications of Slow or Floating CMOS Inputs, literature number SCBA004. electrical characteristics over recommended operating free-air temperature range (unless otherwise noted) PARAMETER MIN TA = 25°C TYP MAX 2V 1.9 2 1.9 1.9 3V 2.9 3 2.9 2.9 4.5 V 4.4 4.5 4.4 4.4 IOH = –4 mA 3V 2.58 2.48 2.48 IOH = –8 mA 4.5 V 3.94 3.8 3.8 TEST CONDITIONS VCC IOH = –50 mA VOH IOL = 50 mA VOL IOL = 4 mA II IOL = 8 mA VI = 5.5 V or GND IOZ† VO = VCC or GND, VI (OE) = VIL or VIH ICC Ci VI = VCC or GND, VI = VCC or GND IO = 0 SN54AHC240 MIN MAX SN74AHC240 MIN MAX UNIT V 2V 0.1 0.1 0.1 3V 0.1 0.1 0.1 4.5 V 0.1 0.1 0.1 3V 0.36 0.5 0.44 V 4.5 V 0.36 0.5 0.44 0 V to 5.5 V ±0.1 ±1* ±1 mA 5.5 V ±0.25 ±2.5 ±2.5 mA 4 40 40 mA 10 pF 5.5 V 5V 2.5 Co 10 VO = VCC or GND 5V 3.5 * On products compliant to MIL-PRF-38535, this parameter is not production tested at VCC = 0 V. † The parameter IOZ includes the input leakage current. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 pF 3 SN54AHC240, SN74AHC240 OCTAL BUFFERS/DRIVERS WITH 3-STATE OUTPUTS SCLS251H – OCTOBER 1995 – REVISED JULY 2003 switching characteristics over recommended operating free-air temperature range, VCC = 3.3 V ± 0.3 V (unless otherwise noted) (see Figure 1) PARAMETER FROM (INPUT) TO (OUTPUT) LOAD CAPACITANCE tPLH tPHL A Y CL = 15 pF tPZH tPZL OE Y CL = 15 pF tPHZ tPLZ OE Y CL = 15 pF tPLH tPHL A Y CL = 50 pF tPZH tPZL OE Y CL = 50 pF tPHZ tPLZ OE Y CL = 50 pF MIN TA = 25°C TYP MAX SN54AHC240 SN74AHC240 MIN MAX MIN MAX 5.3* 7.5* 1* 9* 1 9 5.3* 7.5* 1* 9* 1 9 6.6* 10.6* 1* 12.5* 1 12.5 6.6* 10.6* 1* 12.5* 1 12.5 7.8* 11.5* 1* 12.5* 1 12.5 7.8* 11.5* 1* 12.5* 1 12.5 7.8 11 1 12.5 1 12.5 7.8 11 1 12.5 1 12.5 9.1 14.1 1 16 1 16 9.1 14.1 1 16 1 16 10.3 14 1 16 1 16 10.3 14 1 16 1 16 tsk(o) CL = 50 pF ∗ On products compliant to MIL-PRF-38535, this parameter is not production tested. ∗∗ On products compliant to MIL-PRF-38535, this parameter does not apply. 1.5** 1.5 UNIT ns ns ns ns ns ns ns switching characteristics over recommended operating free-air temperature range, VCC = 5 V ± 0.5 V (unless otherwise noted) (see Figure 1) PARAMETER FROM (INPUT) TO (OUTPUT) LOAD CAPACITANCE tPLH tPHL A Y CL = 15 pF tPZH tPZL OE Y CL = 15 pF tPHZ tPLZ OE Y CL = 15 pF tPLH tPHL A Y CL = 50 pF tPZH tPZL OE Y CL = 50 pF tPHZ tPLZ OE Y CL = 50 pF MIN TA = 25°C TYP MAX POST OFFICE BOX 655303 SN74AHC240 MIN MAX MIN MAX 3.6* 5.5* 1* 6.5* 1 6.5 3.6* 5.5* 1* 6.5* 1 6.5 4.7* 7.3* 1* 8.5* 1 8.5 4.7* 7.3* 1* 8.5* 1 8.5 5.2* 7.2* 1* 8.5* 1 8.5 5.2* 7.2* 1* 8.5* 1 8.5 5.1 7.5 1 8.5 1 8.5 5.1 7.5 1 8.5 1 8.5 6.2 9.3 1 10.5 1 10.5 6.2 9.3 1 10.5 1 10.5 6.7 9.2 1 10.5 1 10.5 6.7 9.2 1 10.5 1 10.5 tsk(o) CL = 50 pF ∗ On products compliant to MIL-PRF-38535, this parameter is not production tested. ∗∗ On products compliant to MIL-PRF-38535, this parameter does not apply. 4 SN54AHC240 • DALLAS, TEXAS 75265 1** 1 UNIT ns ns ns ns ns ns ns SN54AHC240, SN74AHC240 OCTAL BUFFERS/DRIVERS WITH 3-STATE OUTPUTS SCLS251H – OCTOBER 1995 – REVISED JULY 2003 noise characteristics, VCC = 5 V, CL = 50 pF, TA = 25°C (see Note 4) SN74AHC240 PARAMETER MIN TYP MAX UNIT VOL(P) VOL(V) Quiet output, maximum dynamic VOL 0.6 V Quiet output, minimum dynamic VOL –0.6 V VOH(V) VIH(D) Quiet output, minimum dynamic VOH 4.6 V High-level dynamic input voltage 3.5 VIL(D) Low-level dynamic input voltage NOTE 4: Characteristics are for surface-mount packages only. V 1.5 V TYP UNIT operating characteristics, VCC = 5 V, TA = 25°C PARAMETER Cpd TEST CONDITIONS Power dissipation capacitance No load, POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 f = 1 MHz 10 pF 5 SN54AHC240, SN74AHC240 OCTAL BUFFERS/DRIVERS WITH 3-STATE OUTPUTS SCLS251H – OCTOBER 1995 – REVISED JULY 2003 PARAMETER MEASUREMENT INFORMATION From Output Under Test RL = 1 kΩ From Output Under Test Test Point VCC Open S1 TEST GND CL (see Note A) CL (see Note A) S1 tPLH/tPHL tPLZ/tPZL tPHZ/tPZH Open Drain Open VCC GND VCC LOAD CIRCUIT FOR 3-STATE AND OPEN-DRAIN OUTPUTS LOAD CIRCUIT FOR TOTEM-POLE OUTPUTS VCC 50% VCC Timing Input tw tsu VCC Input 50% VCC 50% VCC 0V th VCC 50% VCC Data Input 50% VCC 0V 0V VOLTAGE WAVEFORMS SETUP AND HOLD TIMES VOLTAGE WAVEFORMS PULSE DURATION VCC 50% VCC Input 50% VCC 0V tPLH In-Phase Output tPHL 50% VCC tPHL Out-of-Phase Output VOH 50% VCC VOL VCC Output Control Output Waveform 1 S1 at VCC (see Note B) 50% VCC 0V tPZL VOH 50% VCC VOL tPLZ ≈VCC 50% VCC tPZH tPLH 50% VCC 50% VCC Output Waveform 2 S1 at GND (see Note B) VOLTAGE WAVEFORMS PROPAGATION DELAY TIMES INVERTING AND NONINVERTING OUTPUTS VOL + 0.3 V VOL tPHZ 50% VCC VOH – 0.3 V VOH ≈0 V VOLTAGE WAVEFORMS ENABLE AND DISABLE TIMES LOW- AND HIGH-LEVEL ENABLING NOTES: A. CL includes probe and jig capacitance. B. Waveform 1 is for an output with internal conditions such that the output is low except when disabled by the output control. Waveform 2 is for an output with internal conditions such that the output is high except when disabled by the output control. C. All input pulses are supplied by generators having the following characteristics: PRR ≤ 1 MHz, ZO = 50 Ω, tr ≤ 3 ns, tf ≤ 3 ns. D. The outputs are measured one at a time with one input transition per measurement. E. All parameters and waveforms are not applicable to all devices. Figure 1. Load Circuit and Voltage Waveforms 6 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 MCFP006B − JANUARY 1995 − REVISED JULY 2003 W (R-GDFP-F20) CERAMIC DUAL FLATPACK Base and Seating Plane 0.300 (7,62) 0.245 (6,22) 0.045 (1,14) 0.026 (0,66) 0.009 (0,23) 0.004 (0,10) 0.100 (2,54) 0.045 (1,14) 0.320 (8,13) MAX 1 0.022 (0,56) 0.015 (0,38) 20 0.050 (1,27) 0.540 (13,72) MAX 0.005 (0,13) MIN 4 Places 10 11 0.370 (9,40) 0.250 (6,35) 0.370 (9,40) 0.250 (6,35) 4040180-4 /D 07/03 NOTES: A. B. C. D. E. All linear dimensions are in inches (millimeters). This drawing is subject to change without notice. This package can be hermetically sealed with a ceramic lid using glass frit. Index point is provided on cap for terminal identification only. Falls within Mil-Std 1835 GDFP2-F20 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 1 MECHANICAL DATA MLCC006B – OCTOBER 1996 FK (S-CQCC-N**) LEADLESS CERAMIC CHIP CARRIER 28 TERMINAL SHOWN 18 17 16 15 14 13 NO. OF TERMINALS ** 12 19 11 20 10 A B MIN MAX MIN MAX 20 0.342 (8,69) 0.358 (9,09) 0.307 (7,80) 0.358 (9,09) 28 0.442 (11,23) 0.458 (11,63) 0.406 (10,31) 0.458 (11,63) 21 9 22 8 44 0.640 (16,26) 0.660 (16,76) 0.495 (12,58) 0.560 (14,22) 23 7 52 0.739 (18,78) 0.761 (19,32) 0.495 (12,58) 0.560 (14,22) 24 6 68 0.938 (23,83) 0.962 (24,43) 0.850 (21,6) 0.858 (21,8) 84 1.141 (28,99) 1.165 (29,59) 1.047 (26,6) 1.063 (27,0) B SQ A SQ 25 5 26 27 28 1 2 3 4 0.080 (2,03) 0.064 (1,63) 0.020 (0,51) 0.010 (0,25) 0.020 (0,51) 0.010 (0,25) 0.055 (1,40) 0.045 (1,14) 0.045 (1,14) 0.035 (0,89) 0.045 (1,14) 0.035 (0,89) 0.028 (0,71) 0.022 (0,54) 0.050 (1,27) 4040140 / D 10/96 NOTES: A. B. C. D. E. All linear dimensions are in inches (millimeters). This drawing is subject to change without notice. This package can be hermetically sealed with a metal lid. The terminals are gold plated. Falls within JEDEC MS-004 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 1 MECHANICAL MPDI002C – JANUARY 1995 – REVISED DECEMBER 20002 N (R-PDIP-T**) PLASTIC DUAL-IN-LINE PACKAGE 16 PINS SHOWN PINS ** 14 16 18 20 A MAX 0.775 (19,69) 0.775 (19,69) 0.920 (23,37) 1.060 (26,92) A MIN 0.745 (18,92) 0.745 (18,92) 0.850 (21,59) 0.940 (23,88) MS-100 VARIATION AA BB AC DIM A 16 9 0.260 (6,60) 0.240 (6,10) 1 C AD 8 0.070 (1,78) 0.045 (1,14) 0.045 (1,14) 0.030 (0,76) D D 0.325 (8,26) 0.300 (7,62) 0.020 (0,51) MIN 0.015 (0,38) Gauge Plane 0.200 (5,08) MAX Seating Plane 0.010 (0,25) NOM 0.125 (3,18) MIN 0.100 (2,54) 0.430 (10,92) MAX 0.021 (0,53) 0.015 (0,38) 0.010 (0,25) M 14/18 PIN ONLY 20 pin vendor option D 4040049/E 12/2002 NOTES: A. All linear dimensions are in inches (millimeters). B. This drawing is subject to change without notice. C. Falls within JEDEC MS-001, except 18 and 20 pin minimum body lrngth (Dim A). D. The 20 pin end lead shoulder width is a vendor option, either half or full width. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 1 MECHANICAL DATA MPDS006C – FEBRUARY 1996 – REVISED AUGUST 2000 DGV (R-PDSO-G**) PLASTIC SMALL-OUTLINE 24 PINS SHOWN 0,40 0,23 0,13 24 13 0,07 M 0,16 NOM 4,50 4,30 6,60 6,20 Gage Plane 0,25 0°–8° 1 0,75 0,50 12 A Seating Plane 0,15 0,05 1,20 MAX PINS ** 0,08 14 16 20 24 38 48 56 A MAX 3,70 3,70 5,10 5,10 7,90 9,80 11,40 A MIN 3,50 3,50 4,90 4,90 7,70 9,60 11,20 DIM 4073251/E 08/00 NOTES: A. B. C. D. All linear dimensions are in millimeters. This drawing is subject to change without notice. Body dimensions do not include mold flash or protrusion, not to exceed 0,15 per side. Falls within JEDEC: 24/48 Pins – MO-153 14/16/20/56 Pins – MO-194 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 1 MECHANICAL DATA MSOI003E – JANUARY 1995 – REVISED SEPTEMBER 2001 DW (R-PDSO-G**) PLASTIC SMALL-OUTLINE PACKAGE 16 PINS SHOWN 0.020 (0,51) 0.014 (0,35) 9 0.050 (1,27) 16 0.010 (0,25) 0.419 (10,65) 0.400 (10,15) 0.010 (0,25) NOM 0.299 (7,59) 0.291 (7,39) Gage Plane 0.010 (0,25) 1 8 0°– 8° 0.050 (1,27) 0.016 (0,40) A Seating Plane 0.104 (2,65) MAX 0.012 (0,30) 0.004 (0,10) PINS ** 0.004 (0,10) 16 18 20 24 28 A MAX 0.410 (10,41) 0.462 (11,73) 0.510 (12,95) 0.610 (15,49) 0.710 (18,03) A MIN 0.400 (10,16) 0.453 (11,51) 0.500 (12,70) 0.600 (15,24) 0.700 (17,78) DIM 4040000/E 08/01 NOTES: A. B. C. D. All linear dimensions are in inches (millimeters). This drawing is subject to change without notice. Body dimensions do not include mold flash or protrusion not to exceed 0.006 (0,15). Falls within JEDEC MS-013 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 1 MECHANICAL DATA MSSO002E – JANUARY 1995 – REVISED DECEMBER 2001 DB (R-PDSO-G**) PLASTIC SMALL-OUTLINE 28 PINS SHOWN 0,38 0,22 0,65 28 0,15 M 15 0,25 0,09 8,20 7,40 5,60 5,00 Gage Plane 1 14 0,25 A 0°–ā8° 0,95 0,55 Seating Plane 2,00 MAX 0,10 0,05 MIN PINS ** 14 16 20 24 28 30 38 A MAX 6,50 6,50 7,50 8,50 10,50 10,50 12,90 A MIN 5,90 5,90 6,90 7,90 9,90 9,90 12,30 DIM 4040065 /E 12/01 NOTES: A. B. C. D. All linear dimensions are in millimeters. This drawing is subject to change without notice. Body dimensions do not include mold flash or protrusion not to exceed 0,15. Falls within JEDEC MO-150 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 1 MECHANICAL DATA MTSS001C – JANUARY 1995 – REVISED FEBRUARY 1999 PW (R-PDSO-G**) PLASTIC SMALL-OUTLINE PACKAGE 14 PINS SHOWN 0,30 0,19 0,65 14 0,10 M 8 0,15 NOM 4,50 4,30 6,60 6,20 Gage Plane 0,25 1 7 0°– 8° A 0,75 0,50 Seating Plane 0,15 0,05 1,20 MAX PINS ** 0,10 8 14 16 20 24 28 A MAX 3,10 5,10 5,10 6,60 7,90 9,80 A MIN 2,90 4,90 4,90 6,40 7,70 9,60 DIM 4040064/F 01/97 NOTES: A. B. C. D. All linear dimensions are in millimeters. This drawing is subject to change without notice. Body dimensions do not include mold flash or protrusion not to exceed 0,15. Falls within JEDEC MO-153 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 1 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Amplifiers Applications amplifier.ti.com Audio www.ti.com/audio Data Converters dataconverter.ti.com Automotive www.ti.com/automotive DSP dsp.ti.com Broadband www.ti.com/broadband Interface interface.ti.com Digital Control www.ti.com/digitalcontrol Logic logic.ti.com Military www.ti.com/military Power Mgmt power.ti.com Optical Networking www.ti.com/opticalnetwork Microcontrollers microcontroller.ti.com Security www.ti.com/security Telephony www.ti.com/telephony Video & Imaging www.ti.com/video Wireless www.ti.com/wireless Mailing Address: Texas Instruments Post Office Box 655303 Dallas, Texas 75265 Copyright 2003, Texas Instruments Incorporated