FUJITSU MB2146-302A

FUJITSU SEMICONDUCTOR
DATA SHEET
DS07-12616-1E
8-bit Proprietary Microcontrollers
CMOS
F2MC-8FX MB95120 series
MB95F128D/F128E/FV100D-101/FV100D-102
■ DESCRIPTION
The MB95120 series is general-purpose, single-chip microcontrollers. In addition to a compact instruction set,
the microcontrollers contain a variety of peripheral functions.
Note : F2MC is the abbreviation of FUJITSU Flexible Microcontroller.
■ FEATURE
• F2MC-8FX CPU core
Instruction set optimized for controllers
• Multiplication and division instructions
• 16-bit arithmetic operations
• Bit test branch instruction
• Bit manipulation instructions etc.
• Clock
• Main clock
• Main PLL clock
• Sub clock
• Sub PLL clock
• Timer
• 8/16-bit compound timer × 2 channels
• 16-bit reload timer
• 8/16-bit PPG × 2 channels
• 16-bit PPG × 2 channels
• Timebase timer
• Watch prescaler
(Continued)
Be sure to refer to the “Check Sheet” for the latest cautions on development.
“Check Sheet” is seen at the following support page
URL : http://www.fujitsu.com/global/services/microelectronics/product/micom/support/index.html
“Check Sheet” lists the minimal requirement items to be checked to prevent problems beforehand in system
development.
Copyright©2007 FUJITSU LIMITED All rights reserved
MB95120 Series
(Continued)
• LIN-UART
• Full duplex double buffer
• Clock asynchronous (UART) or clock synchronous (SIO) serial data transfer capable
• UART/SIO
• Full duplex double buffer
• Clock asynchronous (UART) or clock synchronous (SIO) serial data transfer capable
• I2C*
• Built-in wake-up function
• External interrupt
• Interrupt by edge detection (rising, falling, or both edges can be selected)
• Can be used to recover from low-power consumption (standby) modes.
• 8/10-bit A/D converter
• 8-bit or 10-bit resolution can be selected
• LCD controller (LCDC)
• 40 SEG × 4 COM (Max 160 pixels)
• With blinking function
• Built-in division resistance for LCD drive/booster : selected by mask option
• Low-power consumption (standby) mode
• Stop mode
• Sleep mode
• Watch mode
• Timebase timer mode
• I/O port
• The number of maximum ports : Max 87
• Port configuration
• General-purpose I/O ports (N-ch open drain) : 2 ports
• General-purpose I/O ports (CMOS)
: 85 ports
• Programmable input voltage levels of port
• CMOS input level / hysteresis input level
• Dual operation Flash memory
• Erase/write and read can be executed in the different bank (Upper Bank/Lower Bank) at the same time.
• Flash memory security function
Protects the content of Flash memory (Flash memory product only)
*:
2
Purchase of Fujitsu I2C components conveys a license under the Philips I2C Patent Rights to use, these
components in an I2C system provided that the system conforms to the I2C Standard Specification as defined
by Philips.
MB95120 Series
■ PRODUCT LINEUP
Part number*1
MB95F128D
MB95F128E
Parameter
Type
Flash memory product
60 Kbytes
RAM capacity
2 Kbytes
Reset output
No
Option*2
ROM capacity
Clock system
Low voltage
detection reset
CPU functions
Peripheral functions
Dual clock
No
Number of basic instructions
: 136
Instruction bit length
: 8 bits
Instruction length
: 1 to 3 bytes
Data bit length
: 1, 8, and 16 bits
Minimum instruction execution time : 61.5 ns (at machine clock frequency 16.25 MHz)
Interrupt processing time
: 0.6 µs (at machine clock frequency 16.25 MHz)
Ports (Max 87 ports)
General-purpose I/O port (N-ch open drain)
General-purpose I/O port (CMOS)
Programmable input voltage levels of port
CMOS input level / hysteresis input level
: 2 ports
: 85 ports
Timebase timer
Interrupt cycle : 0.5 ms, 2.1 ms, 8.2 ms, 32.8 ms (at main oscillation clock 4 MHz)
Watchdog timer
Reset generated cycle
At main oscillation clock 10 MHz
At sub oscillation clock 32.768 kHz
Wild register
Capable of replacing 3 bytes of ROM data
I2C
Master/slave sending and receiving
Bus error function and arbitration function
Detecting transmitting direction function
Start condition repeated generation and detection functions
Built-in wake-up function
UART/SIO
Data transfer capable in UART/SIO
Full duplex double buffer
Variable data length (5/6/7/8-bit), built-in baud rate generator
NRZ type transfer format, error detected function
LSB-first or MSB-first can be selected
Clock asynchronous (UART) or clock synchronous (SIO) serial data transfer capable
LIN-UART
Dedicated reload timer allowing a wide range of communication speeds to be set
Full duplex double buffer
Clock asynchronous (UART) or clock synchronous (SIO) serial data transfer capable
LIN functions available as the LIN master or LIN slave
: Min 105 ms
: Min 250 ms
8/10-bit A/D converter
8-bit or 10-bit resolution can be selected
(12 channels)
(Continued)
3
MB95120 Series
(Continued)
Part number*1
MB95F128D
MB95F128E
Parameter
LCD controller
(LCDC)
COM output
: 4 (Max)
SEG output
: 40 (Max)
LCD drive power supply (bias) pin
:4
40 SEG × 4 COM
: 160 pixels can be displayed
Duty LCD mode
With blinking function
Division resistance for LCD drive/booster : selected by mask option
Built-in internal division resistance :
selected by mask option
Peripheral functions
16-bit reload timer
Built-in booster circuit :
selected by mask option
Two clock modes and two counter operating modes can be selected
Square wave form output
Count clock : 7 internal clocks and external clock can be selected
Counter operating mode : reload mode or one-shot mode can be selected
Each channel of the timer can be used as “8-bit timer × 2 channels” or “16-bit timer ×
1 channel”
8/16-bit compound
Built-in timer function, PWC function, PWM function, capture function and square
timer (2 channels)
wave form output
Count clock : 7 internal clocks and external clock can be selected
16-bit PPG
(2 channels)
PWM mode or one-shot mode can be selected
Counter operating clock : Eight selectable clock sources
Support for external trigger start
8/16-bit PPG
(2 channels)
Each channel of the PPG can be used as “8-bit PPG × 2 channels” or “16-bit PPG ×
1 channel”
Counter operating clock : Eight selectable clock sources
Watch counter
Count clock : Four selectable clock sources (125 ms, 250 ms, 500 ms, or 1 s)
Counter value can be set from 0 to 63 (Capable of counting for 1 minute when selecting
clock source 1 second and setting counter value to 60)
Watch prescaler
4 selectable interval times (125 ms, 250 ms, 500 ms, or 1 s)
External interrupt
(12 channels)
Interrupt by edge detection (rising, falling, or both edges can be selected)
Can be used to recover from standby modes
Flash memory
Supports automatic programming, Embedded AlgorithmTM *3
Write/Erase/Erase-Suspend/Resume commands
A flag indicating completion of the algorithm
Number of write/erase cycles (Minimum) : 10000 times
Data retention time : 20 years
Erase can be performed on each block
Block protection with external programming voltage
Dual operation Flash memory
Flash Security Feature for protecting the content of the Flash
Standby mode
Sleep, stop, watch, and timebase timer
*1 : MASK ROM products are currently under consideration.
*2 : For details of option, refer to “■ MASK OPTION”.
*3 : Embedded Algorithm is a trade mark of Advanced Micro Devices Inc.
Note : Part number of evaluation product in MB95120 series is MB95FV100D-101 (internal division resistance
included) or MB95FV100D-102 (LCD booster circuit included) . When using it, the MCU board (MB2146301A or MB2146-302A) is required.
4
MB95120 Series
■ OSCILLATION STABILIZATION WAIT TIME
The initial value of the main clock oscillation stabilization wait time is fixed to the maximum value. The maximum
value is shown as follows.
Oscillation stabilization wait time
Remarks
(214−2) /FCH
Approx. 4.10 ms (at main oscillation clock 4 MHz)
■ PACKAGES AND CORRESPONDING PRODUCTS
Part number
Package
MB95F128D/F128E
MB95FV100D-101/102
FPT-100P-M20
FPT-100P-M06
BGA-224P-M08
: Available
: Unavailable
5
MB95120 Series
■ DIFFERENCES AMONG PRODUCTS AND NOTES ON SELECTING PRODUCTS
• Notes on Using Evaluation Products
The Evaluation product has not only the functions of the MB95120 series but also those of other products to
support software development for multiple series and models of the F2MC-8FX family. The I/O addresses for
peripheral resources not used by the MB95120 series are therefore access-barred. Read/write access to these
access-barred addresses may cause peripheral resources supposed to be unused to operate, resulting in
unexpected malfunctions of hardware or software.
Particularly, do not use word access to odd numbered byte address in the prohibited areas (If these access are
used, the address may be read or written unexpectedly).
Also, as the read values of prohibited addresses on the evaluation product are different to the values on the
Flash memory and mask ROM products, do not use these values in the program.
The functions corresponding to certain bits in single-byte registers may not be supported on Flash memory
products. However, reading or writing to these bits will not cause malfunction of the hardware. Also, as the
evaluation and Flash memory products are designed to have identical software operation, no particular
precautions are required.
• Difference of Memory Spaces
If the amount of memory on the Evaluation product is different from that of the Flash memory product, carefully
check the difference in the amount of memory from the model to be actually used when developing software.
For details of memory space, refer to “■ CPU CORE”.
• Current Consumption
For details of current consumption, refer to “■ ELECTRICAL CHARACTERISTICS”.
• Package
For details of information on each package, refer to “■ PACKAGES AND CORRESPONDING PRODUCTS”
and “■ PACKAGE DIMENSIONS”.
• Operating voltage
The operating voltage are different between the Evaluation and Flash memory products.
For details of operating voltage, refer to “■ ELECTRICAL CHARACTERISTICS”.
6
MB95120 Series
■ PIN ASSIGNMENT
VCC
P90/V3
P91/V2
P92/V1
P93/V0
P94/C0
P95/C1
PA0/COM0
PA1/COM1
PA2/COM2
PA3/COM3
PB0/SEG00
PB1/SEG01
PB2/SEG02
PB3/SEG03
PB4/SEG04
PB5/SEG05
PB6/SEG06
PB7/SEG07
PC0/SEG08
PC1/SEG09
PC2/SEG10
PC3/SEG11
PC4/SEG12
VCC
(TOP VIEW)
10099 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 80 79 78 77 76
VSS
PG0
P00/INT00
P01/INT01
P02/INT02
P03/INT03
P04/INT04
P05/INT05
P06/INT06
P07/INT07
P10/UI0
P11/UO0
P12/UCK0
P13/TRG0/ADTG
P14/PPG0
P20/PPG00
P21/PPG01
P22/TO00
P23/TO01
P24/EC0
P50/SCL0
P51/SDA0
P52/PPG1
AVR
AVCC
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
60
59
58
57
56
55
54
53
52
51
PC5/SEG13
PC6/SEG14
PC7/SEG15
PD0/SEG16
PD1/SEG17
PD2/SEG18
PD3/SEG19
PD4/SEG20
PD5/SEG21
PD6/SEG22
PD7/SEG23
PE0/SEG24
PE1/SEG25
PE2/SEG26
PE3/SEG27
PE4/SEG28/INT10
PE5/SEG29/INT11
PE6/SEG30/INT12
PE7/SEG31/INT13
P60/SEG32/PPG10
P61/SEG33/PPG11
MOD
X0
X1
VSS
AVSS
P30/AN00
P31/AN01
P32/AN02
P33/AN03
P34/AN04
P35/AN05
P36/AN06
P37/AN07
P40/AN08
P41/AN09
P42/AN10
P43/AN11
P53/TRG1
P70/TO0
P71/TI0
P67/SEG39/SIN
P66/SEG38/SOT
P65/SEG37/SCK
P64/SEG36/EC1
P63/SEG35/TO11
P62/SEG34/TO10
RST
X0A
X1A
26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50
(FPT-100P-M20)
Note : The P90 to P95 are not used as a general-purpose ports in the MB95F128E.
(Continued)
7
MB95120 Series
(Continued)
P92/V1
P93/V0
P94/C0
P95/C1
PA0/COM0
PA1/COM1
PA2/COM2
PA3/COM3
PB0/SEG00
PB1/SEG01
PB2/SEG02
PB3/SEG03
PB4/SEG04
PB5/SEG05
PB6/SEG06
PB7/SEG07
PC0/SEG08
PC1/SEG09
PC2/SEG10
PC3/SEG11
(TOP VIEW)
100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81
P91/V2
P90/V3
VCC
VSS
PG0
P00/INT00
P01/INT01
P02/INT02
P03/INT03
P04/INT04
P05/INT05
P06/INT06
P07/INT07
P10/UI0
P11/UO0
P12/UCK0
P13/TRG0/ADTG
P14/PPG0
P20/PPG00
P21/PPG01
P22/TO00
P23/TO01
P24/EC0
P50/SCL0
P51/SDA0
P52/PPG1
AVR
AVCC
AVSS
P30/AN00
80
79
78
77
76
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
60
59
58
57
56
55
54
53
52
51
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
P31/AN01
P32/AN02
P33/AN03
P34/AN04
P35/AN05
P36/AN06
P37/AN07
P40/AN08
P41/AN09
P42/AN10
P43/AN11
P53/TRG1
P70/TO0
P71/TI0
P67/SEG39/SIN
P66/SEG38/SOT
P65/SEG37/SCK
P64/SEG36/EC1
P63/SEG35/TO11
P62/SEG34/TO10
31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50
(FPT-100P-M06)
Note : The P90 to P95 are not used as a general-purpose ports in the MB95F128E.
8
PC4/SEG12
VCC
PC5/SEG13
PC6/SEG14
PC7/SEG15
PD0/SEG16
PD1/SEG17
PD2/SEG18
PD3/SEG19
PD4/SEG20
PD5/SEG21
PD6/SEG22
PD7/SEG23
PE0/SEG24
PE1/SEG25
PE2/SEG26
PE3/SEG27
PE4/SEG28/INT10
PE5/SEG29/INT11
PE6/SEG30/INT12
PE7/SEG31/INT13
P60/SEG32/PPG10
P61/SEG33/PPG11
MOD
X0
X1
VSS
X1A
X0A
RST
MB95120 Series
■ PIN DESCRIPTION
Pin no.
Pin name
I/O
circuit
type*3
Function
LQFP *1
QFP *2
1
4
VSS
⎯
Power supply pin (GND)
2
5
PG0
H
General-purpose I/O port
3
6
P00/INT00
4
7
P01/INT01
5
8
P02/INT02
6
9
P03/INT03
7
10
P04/INT04
C
General-purpose I/O port
The pins are shared with external interrupt input. Large
current port.
8
11
P05/INT05
9
12
P06/INT06
10
13
P07/INT07
11
14
P10/UI0
G
General-purpose I/O port
The pin is shared with UART/SIO ch.0 data input.
12
15
P11/UO0
13
16
P12/UCK0
14
17
P13/TRG0/
ADTG
15
18
P14/PPG0
16
19
P20/PPG00
17
20
P21/PPG01
18
21
P22/TO00
19
22
P23/TO01
20
23
P24/EC0
General-purpose I/O port
The pin is shared with 8/16-bit compound timer ch.0 clock
input.
21
24
P50/SCL0
General-purpose I/O port
The pin is shared with I2C ch.0 clock I/O.
General-purpose I/O port
The pin is shared with UART/SIO ch.0 data output.
General-purpose I/O port
The pin is shared with UART/SIO ch.0 clock I/O.
H
General-purpose I/O port
The pin is shared with 16-bit PPG ch.0 trigger input (TRG0)
and A/D converter trigger input (ADTG).
General-purpose I/O port
The pin is shared with 16-bit PPG ch.0 output.
General-purpose I/O port
The pins are shared with 8/16-bit PPG ch.0 output.
H
I
General-purpose I/O port
The pins are shared with 8/16-bit compound timer ch.0
output.
General-purpose I/O port
The pin is shared with I2C ch.0 data I/O.
22
25
P51/SDA0
23
26
P52/PPG1
H
General-purpose I/O port
The pin is shared with 16-bit PPG ch.1 output.
24
27
AVR
⎯
A/D converter reference input pin
25
28
AVCC
⎯
A/D converter power supply pin
(Continued)
9
MB95120 Series
Pin no.
Pin name
I/O
circuit
type*3
⎯
A/D converter power supply pin (GND)
J
General-purpose I/O port
The pins are shared with A/D converter analog input.
J
General-purpose I/O port
The pins are shared with A/D converter analog input.
H
General-purpose I/O port
The pin is shared with 16-bit PPG ch.1 trigger input.
LQFP *1
QFP *2
26
29
AVSS
27
30
P30/AN00
28
31
P31/AN01
29
32
P32/AN02
30
33
P33/AN03
31
34
P34/AN04
32
35
P35/AN05
33
36
P36/AN06
34
37
P37/AN07
35
38
P40/AN08
36
39
P41/AN09
37
40
P42/AN10
38
41
P43/AN11
39
42
P53/TRG1
40
43
P70/TO0
H
Function
General-purpose I/O port
The pin is shared with 16-bit reload timer ch.0 output.
General-purpose I/O port
The pin is shared with 16-bit reload timer ch.0 input.
41
44
P71/TI0
42
45
P67/SEG39/
SIN
43
46
P66/SEG38/
SOT
General-purpose I/O port
The pin is shared with LIN-UART data output (SOT) and
LCDC SEG output (SEG38) .
44
47
P65/SEG37/
SCK
General-purpose I/O port
The pin is shared with LIN-UART clock I/O (SCK) and LCDC
SEG output (SEG37) .
45
48
P64/SEG36/
EC1
46
49
P63/SEG35/
TO11
47
50
P62/SEG34/
TO10
48
51
RST
49
52
X0A
50
53
X1A
51
54
VSS
N
M
General-purpose I/O port
The pin is shared with LIN-UART data input (SIN) and
LCDC SEG output (SEG39) .
General-purpose I/O port
The pin is shared with 8/16-bit compound timer ch.1 clock
input (EC1) and LCDC SEG output (SEG36) .
General-purpose I/O port
The pins are shared with 8/16-bit compound timer ch.1
output (TO10, TO11) and LCDC SEG output (SEG34,
SEG35) .
B'
Reset pin
A
Sub clock oscillation pins (32 kHz)
⎯
Power supply pin (GND)
(Continued)
10
MB95120 Series
Pin no.
Pin name
LQFP *1
QFP *2
52
55
X1
53
56
X0
54
57
MOD
55
58
P61/SEG33/
PPG11
56
59
P60/SEG32/
PPG10
57
60
PE7/SEG31/
INT13
58
61
PE6/SEG30/
INT12
59
62
PE5/SEG29/
INT11
60
63
PE4/SEG28/
INT10
61
64
PE3/SEG27
62
65
PE2/SEG26
63
66
PE1/SEG25
64
67
PE0/SEG24
65
68
PD7/SEG23
66
69
PD6/SEG22
67
70
PD5/SEG21
68
71
PD4/SEG20
69
72
PD3/SEG19
70
73
PD2/SEG18
71
74
PD1/SEG17
72
75
PD0/SEG16
73
76
PC7/SEG15
74
77
PC6/SEG14
75
78
PC5/SEG13
76
79
VCC
I/O
circuit
type*3
Function
A
Main clock oscillation pins
B
An operating mode designation pin
M
General-purpose I/O port
The pins are shared with 8/16-bit PPG ch.1 output (PPG10,
PPG11) and LCDC SEG output (SEG32, SEG33) .
Q
General-purpose I/O port
The pins are shared with external interrupt input (INT10 to
INT13) and LCDC SEG output (SEG28 to SEG31) .
M
General-purpose I/O port
The pins are shared with LCDC SEG output.
M
General-purpose I/O port
The pins are shared with LCDC SEG output.
M
General-purpose I/O port
The pins are shared with LCDC SEG output.
⎯
Power supply pin
(Continued)
11
MB95120 Series
(Continued)
Pin no.
Pin name
LQFP *1
QFP *2
77
80
PC4/SEG12
78
81
PC3/SEG11
79
82
PC2/SEG10
80
83
PC1/SEG09
81
84
PC0/SEG08
82
85
PB7/SEG07
83
86
PB6/SEG06
84
87
PB5/SEG05
85
88
PB4/SEG04
86
89
PB3/SEG03
87
90
PB2/SEG02
88
91
PB1/SEG01
89
92
PB0/SEG00
90
93
PA3/COM3
91
94
PA2/COM2
92
95
PA1/COM1
93
96
PA0/COM0
94
97
P95*4/C1
95
98
P94*4/C0
96
99
P93*4/V0
97
100
P92*4/V1
98
1
P91*4/V2
99
2
P90*4/V3
100
3
VCC
I/O
circuit
type*3
Function
M
General-purpose I/O port
The pins are shared with LCDC SEG output.
M
General-purpose I/O port
The pins are shared with LCDC SEG output.
M
General-purpose I/O port
The pins are shared with LCDC COM output.
S
General-purpose I/O port
R
General-purpose I/O port
The pins are shared with power supply pins for LCDC
drive.
⎯
Power supply pin
*1 : FPT-100P-M20
*2 : FPT-100P-M06
*3 : For the I/O circuit type, refer to “■ I/O CIRCUIT TYPE”.
*4 : The P90 to P95 are not used as a general-purpose ports in the MB95F128E.
12
MB95120 Series
■ I/O CIRCUIT TYPE
Type
Circuit
X1 (X1A)
A
Remarks
Clock input
N-ch
X0 (X0A)
Standby control
B
Mode input
• Oscillation circuit
• High-speed side
Feedback resistance : approx. 1 MΩ
• Low-speed side
Feedback resistance : approx. 24 MΩ
(Evaluation product : approx.10 MΩ)
Damping resistance : approx.144 kΩ
(Evaluation product : non-damping
resistance )
• Only for input
• Hysteresis input
Hysteresis input
Reset input
B’
P-ch
N-ch
C
Digital output
• CMOS output
• Hysteresis input
Digital output
Hysteresis input
Standby control
External interrupt
enable
R
P-ch
Pull-up control
P-ch
G
N-ch
Digital output
•
•
•
•
CMOS output
CMOS input
Hysteresis input
With pull-up control
Digital output
CMOS input
Hysteresis input
Standby control
Pull-up control
R
P-ch
P-ch
H
N-ch
Standby control
• CMOS output
• Hysteresis input
• With pull-up control
Digital output
Digital output
Hysteresis input
(Continued)
13
MB95120 Series
Type
Circuit
N-ch
Remarks
Digital output
• N-ch open drain output
• CMOS input
• Hysteresis input
I
CMOS input
Hysteresis input
Standby control
R
P-ch
Pull-up control
P-ch
J
N-ch
Digital output
•
•
•
•
CMOS output
Hysteresis input
Analog input
With pull-up control
Digital output
Analog input
Hysteresis input
A/D control
Standby control
P-ch
Digital output
Digital output
N-ch
M
• CMOS output
• LCD output
• Hysteresis input
LCD output
LCD control
Standby control
Hysteresis input
P-ch
N-ch
Digital output
Digital output
•
•
•
•
CMOS output
LCD output
CMOS input
Hysteresis input
N
LCD output
LCD control
Standby control
CMOS input
Hysteresis input
(Continued)
14
MB95120 Series
(Continued)
Type
Circuit
P-ch
N-ch
Remarks
Digital output
• CMOS output
• LCD output
• Hysteresis input
Digital output
Q
LCD output
LCD control
Standby control
Hysteresis input
External
interrupt control
P-ch
N-ch
R
Digital output
• CMOS output
• LCD power supply
• Hysteresis input
Digital output
LCD internal division
resistance I/O
LCD control
Standby control
Hysteresis input
P-ch
N-ch
S
Digital output
• CMOS output
• LCD power supply
• Hysteresis input
Digital output
LCD booster I/O
Standby control
Hysteresis input
15
MB95120 Series
■ HANDLING DEVICES
• Preventing Latch-up
Care must be taken to ensure that maximum voltage ratings are not exceeded when they are used.
Latch-up may occur on CMOS ICs if voltage higher than VCC or lower than VSS is applied to input and output pins
other than medium- and high-withstand voltage pins or if higher than the rating voltage is applied between VCC
pin and VSS pin.
When latch-up occurs, power supply current increases rapidly and might thermally damage elements.
Also, take care to prevent the analog power supply voltage (AVCC , AVR) and analog input voltage from exceeding
the digital power supply voltage (VCC) when the analog system power supply is turned on or off.
• Stable Supply Voltage
Supply voltage should be stabilized.
A sudden change in power-supply voltage may cause a malfunction even within the guaranteed operating range
of the VCC power-supply voltage.
For stabilization, in principle, keep the variation in VCC ripple (p-p value) in a commercial frequency range
(50/60 Hz) not to exceed 10% of the standard VCC value and suppress the voltage variation so that the transient
variation rate does not exceed 0.1 V/ms during a momentary change such as when the power supply is switched.
• Precautions for Use of External Clock
Even when an external clock is used, oscillation stabilization wait time is required for power-on reset, wake-up
from sub clock mode or stop mode.
■ PIN CONNECTION
• Treatment of Unused Pin
Leaving unused input pins unconnected can cause abnormal operation or latch-up, leaving to permanent
damage.
Unused input pins should always be pulled up or down through resistance of at least 2 kΩ. Any unused input/
output pins may be set to output mode and left open, or set to input mode and treated the same as unused input
pins. If there is unused output pin, make it open.
• Treatment of Power Supply Pins on A/D Converter
Connect to be AVCC = VCC and AVSS = AVR = VSS even if the A/D converter is not in use.
Noise riding on the AVCC pin may cause accuracy degradation. So, connect approx. 0.1 µF ceramic capacitor
as a bypass capacitor between AVCC and AVSS pins in the vicinity of this device.
• Power Supply Pins
In products with multiple VCC or VSS pins, the pins of the same potential are internally connected in the device
to avoid abnormal operations including latch-up. However, you must connect the pins to external power supply
and a ground line to lower the electro-magnetic emission level, to prevent abnormal operation of strobe signals
caused by the rise in the ground level, and to conform to the total output current rating.
Moreover, connect the current supply source with the VCC and VSS pins of this device at the low impedance.
It is also advisable to connect a ceramic bypass capacitor of approximately 0.1 µF between VCC and VSS near
this device.
16
MB95120 Series
• Mode Pin (MOD)
Connect the MOD pin directly to VCC or VSS pins.
To prevent the device unintentionally entering test mode due to noise, lay out the printed circuit board so as to
minimize the distance from the MOD pin to VCC or VSS pins and to provide a low-impedance connection.
• Analog Power Supply
Always set the same potential to AVCC and VCC pins. When VCC > AVCC, the current may flow through the AN00
to AN11 pins.
17
MB95120 Series
■ PROGRAMMING FLASH MEMORY MICROCONTROLLERS USING PARALLEL
PROGRAMMER
• Supported Parallel Programmers and Adapters
The following table lists supported parallel programmers and adapters.
Package
Applicable adapter model
FPT-100P-M20
TEF110-95F128HSPFV
FPT-100P-M06
TEF110-95F128HSPF
Parallel programmers
AF9708 (Ver 02.35G or more)
AF9709/B (Ver 02.35G or more)
AF9723+AF9834 (Ver 02.08E or more)
Note : For information on applicable adapter models and parallel programmers, contact the following:
Flash Support Group, Inc. TEL: +81-53-428-8380
• Sector Configuration
The individual sectors of Flash memory correspond to addresses used for CPU access and programming by
the parallel programmer as follows:
• MB95F128D/F128E (60 Kbytes)
Flash memory
CPU address
Programmer address*
1000H
71000H
1FFFH
2000H
71FFFH
72000H
2FFFH
3000H
72FFFH
73000H
3FFFH
4000H
73FFFH
74000H
7FFFH
8000H
77FFFH
78000H
BFFFH
C000H
7BFFFH
7C000H
CFFFH
D000H
7CFFFH
7D000H
DFFFH
E000H
7DFFFH
7E000H
EFFFH
F000H
7EFFFH
7F000H
FFFFH
7FFFFH
SA2 (4 Kbytes)
Lower bank
SA1 (4 Kbytes)
SA3 (4 Kbytes)
SA4 (16 Kbytes)
SA6 (4 Kbytes)
SA7 (4 Kbytes)
Upper bank
SA5 (16 Kbytes)
SA8 (4 Kbytes)
SA9 (4 Kbytes)
*: Programmer addresses are corresponding to CPU addresses, used when the parallel programmer
programs data into Flash memory.
These programmer addresses are used for the parallel programmer to program or erase data in Flash
memory.
• Programming Method
1) Set the type code of the parallel programmer to 17222.
2) Load program data to programmer addresses 71000H to 7FFFFH.
3) Programmed by parallel programmer
18
MB95120 Series
■ BLOCK DIAGRAM
2
F MC-8FX CPU
RST
X0/X1
X0A/X1A
Reset control
ROM
RAM
Clock control
Interrupt control
Watch prescaler
PG0
P00/INT00 to P07/INT07
Wild register
Watch counter
External interrupt ch.0 to ch.7
8/16-bit PPG ch.1
P60/SEG32/PPG10
P61/SEG33/PPG11
P10/UI0
P11/UO0
P62/SEG34/TO10
UART/SIO
8/16-bit compound
timer ch.1
P13/TRG0/ADTG
P14/PPG0
16-bit PPG ch.0
P20/PPG00
P21/PPG01
8/16-bit PPG ch.0
P24/EC0
8/16-bit compound
timer ch.0
P30/AN00 to P37/AN07
P40/AN08 to P43/AN11
AVCC
AVSS
8/10-bit A/D
converter
LCDC
AVR
P50/SCL0
P51/SDA0
P52/PPG1
P53/TRG1
I2C
16-bit PPG ch.1
Port
P63/SEG35/TO11
P64/SEG36/EC1
P65/SEG37/SCK
LIN-UART
16-bit reload timer
P22/TO00
P23/TO01
Internal bus
P12/UCK0
External interrupt ch.8 to ch.11
P66/SEG38/SOT
P67/SEG39/SIN
P70/TO0
P71/TI0
P90/V3 to P93/V0
P94/C0, P95/C1
PA0/COM0 to PA3/COM3
PB0/SEG00 to PB7/SEG07
PC0/SEG08 to PC7/SEG15
PD0/SEG16 to PD7/SEG23
PE0/SEG24 to PE3/SEG27
PE4/SEG28/INT10
PE5/SEG29/INT11
PE6/SEG30/INT12
PE7/SEG31/INT13
Port
Other pins
MOD, VCC
19
MB95120 Series
■ CPU CORE
1. Memory space
Memory space of the MB95120 series is 64 Kbytes and consists of I/O area, data area, and program area. The
memory space includes special - purpose areas such as the general - purpose registers and vector table. Memory
map of the MB95120 series is shown below.
• Memory Map
MB95F128D
MB95F128E
0000H
I/O
0080H
0100H
RAM 2 Kbytes
Register
0200H
0880H
MB95FV100D-101
MB95FV100D-102
0000H
I/O
0080H
0100H
Access
prohibited
0F80H
Extended I/O
Extended I/O
1000H
1000H
Flash memory
60 Kbytes
Flash memory
60 Kbytes
20
Register
0200H
0F80H
FFFFH
RAM 3.75 Kbytes
FFFFH
MB95120 Series
2. Register
The MB95120 series has two types of registers; dedicated registers in the CPU and general-purpose registers
in the memory. The dedicated registers are as follows:
Program counter (PC)
: A 16-bit register to indicate locations where instructions are stored.
Accumulator (A)
: A 16-bit register for temporary storage of arithmetic operations. In the case of
an 8-bit data processing instruction, the lower 1 byte is used.
Temporary accumulator (T) : A 16-bit register which performs arithmetic operations with the accumulator.
In the case of an 8-bit data processing instruction, the lower 1 byte is used.
Index register (IX)
: A 16-bit register for index modification
Extra pointer (EP)
: A 16-bit pointer to point to a memory address.
Stack pointer (SP)
: A 16-bit register to indicate a stack area.
Program status (PS)
: A 16-bit register for storing a register bank pointer, a direct bank pointer, and
a condition code register
Initial Value
16-bit
: Program counter
FFFDH
A
: Accumulator
0000H
T
: Temporary accumulator
0000H
IX
: Index register
0000H
EP
: Extra pointer
0000H
SP
: Stack pointer
0000H
PS
: Program status
0030H
PC
The PS can further be divided into higher 8 bits for use as a register bank pointer (RP) and a direct bank pointer
(DP) and the lower 8 bits for use as a condition code register (CCR) . (Refer to the diagram below.)
• Structure of the program status
bit 15 bit 14 bit 13 bit 12 bit 11 bit 10 bit 9
PS
R4
R3
R2
RP
R1
R0
DP2
DP1
DP
bit 8
bit 7
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
DP0
H
I
IL1
IL0
N
Z
V
C
CCR
21
MB95120 Series
The RP indicates the address of the register bank currently being used. The relationship between the content
of RP and the real address conforms to the conversion rule illustrated below:
• Rule for Conversion of Actual Addresses in the General-purpose Register Area
RP upper
"0"
Generated address
"0"
"0"
"0"
"0"
OP code lower
"0"
"0"
"1"
R4
R3
R2
R1
R0
b2
b1
b0
A15 A14 A13 A12 A11 A10
A9
A8
A7
A6
A5
A4
A3
A2
A1
A0
The DP specifies the area for mapping instructions (16 different instructions such as MOV A, dir) using direct
addresses to 0080H to 00FFH.
Direct bank pointer (DP2 to DP0)
Specified address area
Mapping area
XXXB (no effect to mapping)
0000H to 007FH
0000H to 007FH (without mapping)
000B (initial value)
0080H to 00FFH (without mapping)
001B
0100H to 017FH
010B
0180H to 01FFH
011B
0080H to 00FFH
100B
0200H to 027FH
0280H to 02FFH
101B
0300H to 037FH
110B
0380H to 03FFH
111B
0400H to 047FH
The CCR consists of the bits indicating arithmetic operation results or transfer data contents and the bits that
control CPU operations at interrupt.
H flag
: Set to “1” when a carry or a borrow from bit 3 to bit 4 occurs as a result of an arithmetic operation.
Cleared to “0” otherwise. This flag is for decimal adjustment instructions.
I flag
: Interrupt is enabled when this flag is set to “1”. Interrupt is disabled when this flag is set to “0”.
The flag is cleared to “0” when reset.
IL1, IL0 : Indicates the level of the interrupt currently enabled. Processes an interrupt only if its request level
is higher than the value indicated by these bits.
IL1
Interrupt level
Priority
High
0
0
0
0
1
1
1
0
2
1
1
3
N flag
Z flag
V flag
C flag
22
IL0
Low = no interruption
: Set to “1” if the MSB is set to “1” as the result of an arithmetic operation. Cleared to “0” when the
bit is set to “0”.
: Set to “1” when an arithmetic operation results in “0”. Cleared to “0” otherwise.
: Set to “1” if the complement on 2 overflows as a result of an arithmetic operation. Cleared to “0”
otherwise.
: Set to “1” when a carry or a borrow from bit 7 occurs as a result of an arithmetic operation. Cleared
to “0” otherwise. Set to the shift-out value in the case of a shift instruction.
MB95120 Series
The following general-purpose registers are provided:
General-purpose registers: 8-bit data storage registers
The general-purpose registers are 8 bits and located in the register banks on the memory. 1-bank contains
8-register. Up to a total of 32 banks can be used on the MB95120 series. The bank currently in use is indicated
by the register bank pointer (RP).8-register. Up to a total of 32 banks can be used on the MB95120 series. The
bank currently in use is specified by the register bank pointer (RP), and the lower 3 bits of OP code indicates
the general-purpose register 0 (R0) to general-purpose register 7 (R7).
• Register Bank Configuration
8-bit
1F8H
This address = 0100H + 8 × (RP)
Address 100H
R0
R0
R0
R1
R2
R3
R4
R5
107H
R6
R1
R2
R3
R4
R5
R6
R1
R2
R3
R4
R5
R6
1FFH
R7
R7
R7
Bank 0
Memory area
Bank 31
32 banks
32 banks (RAM area)
The number of banks is
limited by the usable RAM
capacitance.
23
MB95120 Series
■ I/O MAP
Address
Register
abbreviation
Register name
R/W
Initial value
0000H
PDR0
Port 0 data register
R/W
00000000B
0001H
DDR0
Port 0 direction register
R/W
00000000B
0002H
PDR1
Port 1 data register
R/W
00000000B
0003H
DDR1
Port 1 direction register
R/W
00000000B
0004H
⎯
(Disabled)
⎯
⎯
0005H
WATR
Oscillation stabilization wait time setting register
R/W
11111111B
0006H
PLLC
PLL control register
R/W
00000000B
0007H
SYCC
System clock control register
R/W
1010X011B
0008H
STBC
Standby control register
R/W
00000000B
0009H
RSRR
Reset source register
R
XXXXXXXXB
000AH
TBTC
Timebase timer control register
R/W
00000000B
000BH
WPCR
Watch prescaler control register
R/W
00000000B
000CH
WDTC
Watchdog timer control register
R/W
00000000B
000DH
⎯
(Disabled)
⎯
⎯
000EH
PDR2
Port 2 data register
R/W
00000000B
000FH
DDR2
Port 2 direction register
R/W
00000000B
0010H
PDR3
Port 3 data register
R/W
00000000B
0011H
DDR3
Port 3 direction register
R/W
00000000B
0012H
PDR4
Port 4 data register
R/W
00000000B
0013H
DDR4
Port 4 direction register
R/W
00000000B
0014H
PDR5
Port 5 data register
R/W
00000000B
0015H
DDR5
Port 5 direction register
R/W
00000000B
0016H
PDR6
Port 6 data register
R/W
00000000B
0017H
DDR6
Port 6 direction register
R/W
00000000B
0018H
PDR7
Port 7 data register
R/W
00000000B
0019H
DDR7
Port 7 direction register
R/W
00000000B
001AH,
001BH
⎯
(Disabled)
⎯
⎯
001CH
PDR9
Port 9 data register
R/W
00000000B
001DH
DDR9
Port 9 direction register
R/W
00000000B
001EH
PDRA
Port A data register
R/W
00000000B
001FH
DDRA
Port A direction register
R/W
00000000B
0020H
PDRB
Port B data register
R/W
00000000B
0021H
DDRB
Port B direction register
R/W
00000000B
0022H
PDRC
Port C data register
R/W
00000000B
0023H
DDRC
Port C direction register
R/W
00000000B
(Continued)
24
MB95120 Series
Address
Register
abbreviation
Register name
R/W
Initial value
0024H
PDRD
Port D data register
R/W
00000000B
0025H
DDRD
Port D direction register
R/W
00000000B
0026H
PDRE
Port E data register
R/W
00000000B
0027H
DDRE
Port E direction register
R/W
00000000B
0028H,
0029H
⎯
(Disabled)
⎯
⎯
002AH
PDRG
Port G data register
R/W
00000000B
002BH
DDRG
Port G direction register
R/W
00000000B
002CH
⎯
(Disabled)
⎯
⎯
002DH
PUL1
Port 1 pull-up register
R/W
00000000B
002EH
PUL2
Port 2 pull-up register
R/W
00000000B
002FH
PUL3
Port 3 pull-up register
R/W
00000000B
0030H
PUL4
Port 4 pull-up register
R/W
00000000B
0031H
PUL5
Port 5 pull-up register
R/W
00000000B
0032H
PUL7
Port 7 pull-up register
R/W
00000000B
0033H,
0034H
⎯
(Disabled)
⎯
⎯
0035H
PULG
Port G pull-up register
R/W
00000000B
0036H
T01CR1
8/16-bit compound timer 01 control status register 1 ch.0
R/W
00000000B
0037H
T00CR1
8/16-bit compound timer 00 control status register 1 ch.0
R/W
00000000B
0038H
T11CR1
8/16-bit compound timer 11 control status register 1 ch.1
R/W
00000000B
0039H
T10CR1
8/16-bit compound timer 10 control status register 1 ch.1
R/W
00000000B
003AH
PC01
8/16-bit PPG1 control register ch.0
R/W
00000000B
003BH
PC00
8/16-bit PPG0 control register ch.0
R/W
00000000B
003CH
PC11
8/16-bit PPG1 control register ch.1
R/W
00000000B
003DH
PC10
8/16-bit PPG0 control register ch.1
R/W
00000000B
003EH
TMCSRH0
16-bit reload timer control status register (upper byte) ch.0
R/W
00000000B
003FH
TMCSRL0
16-bit reload timer control status register (lower byte) ch.0
R/W
00000000B
0040H,
0041H
⎯
(Disabled)
⎯
⎯
0042H
PCNTH0
16-bit PPG status control register (upper byte) ch.0
R/W
00000000B
0043H
PCNTL0
16-bit PPG status control register (lower byte) ch.0
R/W
00000000B
0044H
PCNTH1
16-bit PPG status control register (upper byte) ch.1
R/W
00000000B
0045H
PCNTL1
16-bit PPG status control register (lower byte) ch.1
R/W
00000000B
0046H,
0047H
⎯
(Disabled)
⎯
⎯
0048H
EIC00
External interrupt circuit control register ch.0/ch.1
R/W
00000000B
0049H
EIC10
External interrupt circuit control register ch.2/ch.3
R/W
00000000B
(Continued)
25
MB95120 Series
Address
Register
abbreviation
Register name
R/W
Initial value
004AH
EIC20
External interrupt circuit control register ch.4/ch.5
R/W
00000000B
004BH
EIC30
External interrupt circuit control register ch.6/ch.7
R/W
00000000B
004CH
EIC01
External interrupt circuit control register ch.8/ch.9
R/W
00000000B
004DH
EIC11
External interrupt circuit control register ch.10/ch.11
R/W
00000000B
004EH,
004FH
⎯
(Disabled)
⎯
⎯
0050H
SCR
LIN-UART serial control register
R/W
00000000B
0051H
SMR
LIN-UART serial mode register
R/W
00000000B
0052H
SSR
LIN-UART serial status register
R/W
00001000B
0053H
RDR/TDR
LIN-UART reception/transmission data register
R/W
00000000B
0054H
ESCR
LIN-UART extended status control register
R/W
00000100B
0055H
ECCR
LIN-UART extended communication control register
R/W
000000XXB
0056H
SMC10
UART/SIO serial mode control register 1 ch.0
R/W
00000000B
0057H
SMC20
UART/SIO serial mode control register 2 ch.0
R/W
00100000B
0058H
SSR0
UART/SIO serial status register ch.0
R/W
00000001B
0059H
TDR0
UART/SIO serial output data register ch.0
R/W
00000000B
005AH
RDR0
UART/SIO serial input data register ch.0
R
00000000B
005BH
to
005FH
⎯
(Disabled)
⎯
⎯
0060H
IBCR00
I2C bus control register 0 ch.0
R/W
00000000B
0061H
IBCR10
I2C bus control register 1 ch.0
R/W
00000000B
0062H
IBSR0
I2C bus status register ch.0
R
00000000B
I C data register ch.0
R/W
00000000B
0063H
2
IDDR0
2
0064H
IAAR0
I C address register ch.0
R/W
00000000B
0065H
ICCR0
I2C clock control register ch.0
R/W
00000000B
0066H
to
006BH
⎯
(Disabled)
⎯
⎯
006CH
ADC1
8/10-bit A/D converter control register 1
R/W
00000000B
006DH
ADC2
8/10-bit A/D converter control register 2
R/W
00000000B
006EH
ADDH
8/10-bit A/D converter data register (upper byte)
R/W
00000000B
006FH
ADDL
8/10-bit A/D converter data register (lower byte)
R/W
00000000B
0070H
WCSR
Watch counter status register
R/W
00000000B
0071H
⎯
(Disabled)
⎯
⎯
0072H
FSR
Flash memory status register
R/W
000X0000B
(Continued)
26
MB95120 Series
Address
Register
abbreviation
Register name
R/W
Initial value
0073H
SWRE0
Flash memory sector writing control register 0
R/W
00000000B
0074H
SWRE1
Flash memory sector writing control register 1
R/W
00000000B
0075H
⎯
(Disabled)
⎯
⎯
0076H
WREN
Wild register address compare enable register
R/W
00000000B
0077H
WROR
Wild register data test setting register
R/W
00000000B
0078H
⎯
Register bank pointer (RP) ,
Mirror of direct bank pointer (DP)
⎯
⎯
0079H
ILR0
Interrupt level setting register 0
R/W
11111111B
007AH
ILR1
Interrupt level setting register 1
R/W
11111111B
007BH
ILR2
Interrupt level setting register 2
R/W
11111111B
007CH
ILR3
Interrupt level setting register 3
R/W
11111111B
007DH
ILR4
Interrupt level setting register 4
R/W
11111111B
007EH
ILR5
Interrupt level setting register 5
R/W
11111111B
007FH
⎯
(Disabled)
⎯
⎯
0F80H
WRARH0
Wild register address setting register (upper byte) ch.0
R/W
00000000B
0F81H
WRARL0
Wild register address setting register (lower byte) ch.0
R/W
00000000B
0F82H
WRDR0
Wild register data setting register ch.0
R/W
00000000B
0F83H
WRARH1
Wild register address setting register (upper byte) ch.1
R/W
00000000B
0F84H
WRARL1
Wild register address setting register (lower byte) ch.1
R/W
00000000B
0F85H
WRDR1
Wild register data setting register ch.1
R/W
00000000B
0F86H
WRARH2
Wild register address setting register (upper byte) ch.2
R/W
00000000B
0F87H
WRARL2
Wild register address setting register (lower byte) ch.2
R/W
00000000B
0F88H
WRDR2
Wild register data setting register ch.2
R/W
00000000B
0F89H
to
0F91H
⎯
(Disabled)
⎯
⎯
0F92H
T01CR0
8/16-bit compound timer 01 control status register 0 ch.0
R/W
00000000B
0F93H
T00CR0
8/16-bit compound timer 00 control status register 0 ch.0
R/W
00000000B
0F94H
T01DR
8/16-bit compound timer 01 data register ch.0
R/W
00000000B
0F95H
T00DR
8/16-bit compound timer 00 data register ch.0
R/W
00000000B
0F96H
TMCR0
8/16-bit compound timer 00/01 timer mode control register
ch.0
R/W
00000000B
0F97H
T11CR0
8/16-bit compound timer 11 control status register 0 ch.1
R/W
00000000B
0F98H
T10CR0
8/16-bit compound timer 10 control status register 0 ch.1
R/W
00000000B
0F99H
T11DR
8/16-bit compound timer 11 data register ch.1
R/W
00000000B
0F9AH
T10DR
8/16-bit compound timer 10 data register ch.1
R/W
00000000B
(Continued)
27
MB95120 Series
Address
Register
abbreviation
Register name
R/W
Initial value
0F9BH
TMCR1
8/16-bit compound timer 10/11 timer mode control register
ch.1
R/W
00000000B
0F9CH
PPS01
8/16-bit PPG1 cycle setting buffer register ch.0
R/W
11111111B
0F9DH
PPS00
8/16-bit PPG0 cycle setting buffer register ch.0
R/W
11111111B
0F9EH
PDS01
8/16-bit PPG1 duty setting buffer register ch.0
R/W
11111111B
0F9FH
PDS00
8/16-bit PPG0 duty setting buffer register ch.0
R/W
11111111B
0FA0H
PPS11
8/16-bit PPG1 cycle setting buffer register ch.1
R/W
11111111B
0FA1H
PPS10
8/16-bit PPG0 cycle setting buffer register ch.1
R/W
11111111B
0FA2H
PDS11
8/16-bit PPG1 duty setting buffer register ch.1
R/W
11111111B
0FA3H
PDS10
8/16-bit PPG0 duty setting buffer register ch.1
R/W
11111111B
0FA4H
PPGS
8/16-bit PPG start register
R/W
00000000B
0FA5H
REVC
8/16-bit PPG output inversion register
R/W
00000000B
0FA6H
TMRH0/
TMRLRH0
16-bit reload timer/reload register (upper byte) ch.0
R/W
00000000B
0FA7H
TMRL0/
TMRLRL0
16-bit reload timer/reload register (lower byte) ch.0
R/W
00000000B
0FA8H,
0FA9H
⎯
(Disabled)
⎯
⎯
0FAAH
PDCRH0
16-bit PPG down counter register (upper byte) ch.0
R
00000000B
0FABH
PDCRL0
16-bit PPG down counter register (lower byte) ch.0
R
00000000B
0FACH
PCSRH0
16-bit PPG cycle setting buffer register (upper byte) ch.0
R/W
11111111B
0FADH
PCSRL0
16-bit PPG cycle setting buffer register (lower byte) ch.0
R/W
11111111B
0FAEH
PDUTH0
16-bit PPG duty setting buffer register (upper byte) ch.0
R/W
11111111B
0FAFH
PDUTL0
16-bit PPG duty setting buffer register (lower byte) ch.0
R/W
11111111B
0FB0H
PDCRH1
16-bit PPG down counter register (upper byte) ch.1
R
00000000B
0FB1H
PDCRL1
16-bit PPG down counter register (lower byte) ch.1
R
00000000B
0FB2H
PCSRH1
16-bit PPG cycle setting buffer register (upper byte) ch.1
R/W
11111111B
0FB3H
PCSRL1
16-bit PPG cycle setting buffer register (lower byte) ch.1
R/W
11111111B
0FB4H
PDUTH1
16-bit PPG duty setting buffer register (upper byte) ch.1
R/W
11111111B
0FB5H
PDUTL1
16-bit PPG duty setting buffer register (lower byte) ch.1
R/W
11111111B
0FB6H
to
0FBBH
⎯
(Disabled)
⎯
⎯
0FBCH
BGR1
LIN-UART baud rate generator register 1
R/W
00000000B
0FBDH
BGR0
LIN-UART baud rate generator register 0
R/W
00000000B
0FBEH
PSSR0
UART/SIO dedicated baud rate generator
prescaler select register ch.0
R/W
00000000B
(Continued)
28
MB95120 Series
(Continued)
Address
Register
abbreviation
Register name
R/W
Initial value
0FBFH
BRSR0
UART/SIO dedicated baud rate generator
baud rate setting register ch.0
R/W
00000000B
0FC0H,
0FC1H
⎯
(Disabled)
⎯
⎯
0FC2H
AIDRH
A/D input disable register (upper byte)
R/W
00000000B
0FC3H
AIDRL
A/D input disable register (lower byte)
R/W
00000000B
0FC4H
LCDCC
LCDC control register
R/W
00010000B
0FC5H
LCDCE1
LCDC enable register 1
R/W
00110000B
0FC6H
LCDCE2
LCDC enable register 2
R/W
00000000B
0FC7H
LCDCE3
LCDC enable register 3
R/W
00000000B
0FC8H
LCDCE4
LCDC enable register 4
R/W
00000000B
0FC9H
LCDCE5
LCDC enable register 5
R/W
00000000B
0FCAH
LCDCE6
LCDC enable register 6
R/W
00000000B
0FCBH
LCDCB1
LCDC blinking setting register 1
R/W
00000000B
0FCCH
LCDCB2
LCDC blinking setting register 2
R/W
00000000B
0FCDH
to
0FE0H
LCDRAM
LCDC display RAM
R/W
00000000B
0FE1H,
0FE2H
⎯
(Disabled)
⎯
⎯
0FE3H
WCDR
Watch counter data register
R/W
00111111B
0FE4H
to
0FEDH
⎯
(Disabled)
⎯
⎯
0FEEH
ILSR
Input level select register
R/W
00000000B
0FEFH
WICR
Interrupt pin select circuit control register
R/W
01000000B
0FF0H
to
0FFFH
⎯
(Disabled)
⎯
⎯
• R/W access symbols
R/W : Readable/Writable
R
: Read only
W
: Write only
• Initial value symbols
0
: The initial value of this bit is “0”.
1
: The initial value of this bit is “1”.
X
: The initial value of this bit is undefined.
Note : Do not write to the “ (Disabled) ”. Reading the “ (Disabled) ” returns an undefined value.
29
MB95120 Series
■ INTERRUPT SOURCE TABLE
Interrupt source
Interrupt
request
number
Vector table address
Same level
Bit name of
priority order
interrupt level
(at simultaneous
setting register
occurrence)
Upper
Lower
IRQ0
FFFAH
FFFBH
L00 [1 : 0]
IRQ1
FFF8H
FFF9H
L01 [1 : 0]
IRQ2
FFF6H
FFF7H
L02 [1 : 0]
IRQ3
FFF4H
FFF5H
L03 [1 : 0]
UART/SIO ch.0
IRQ4
FFF2H
FFF3H
L04 [1 : 0]
8/16-bit compound timer ch.0 (Lower)
IRQ5
FFF0H
FFF1H
L05 [1 : 0]
8/16-bit compound timer ch.0 (Upper)
IRQ6
FFEEH
FFEFH
L06 [1 : 0]
LIN-UART (reception)
IRQ7
FFECH
FFEDH
L07 [1 : 0]
LIN-UART (transmission)
IRQ8
FFEAH
FFEBH
L08 [1 : 0]
8/16-bit PPG ch.1 (Lower)
IRQ9
FFE8H
FFE9H
L09 [1 : 0]
8/16-bit PPG ch.1 (Upper)
IRQ10
FFE6H
FFE7H
L10 [1 : 0]
16-bit reload timer ch.0
IRQ11
FFE4H
FFE5H
L11 [1 : 0]
8/16-bit PPG ch.0 (Upper)
IRQ12
FFE2H
FFE3H
L12 [1 : 0]
8/16-bit PPG ch.0 (Lower)
IRQ13
FFE0H
FFE1H
L13 [1 : 0]
8/16-bit compound timer ch.1 (Upper)
IRQ14
FFDEH
FFDFH
L14 [1 : 0]
16-bit PPG ch.0
IRQ15
FFDCH
FFDDH
L15 [1 : 0]
I2C ch.0
IRQ16
FFDAH
FFDBH
L16 [1 : 0]
16-bit PPG ch.1
IRQ17
FFD8H
FFD9H
L17 [1 : 0]
8/10-bit A/D converter
IRQ18
FFD6H
FFD7H
L18 [1 : 0]
Timebase timer
IRQ19
FFD4H
FFD5H
L19 [1 : 0]
Watch prescaler/watch counter
IRQ20
FFD2H
FFD3H
L20 [1 : 0]
IRQ21
FFD0H
FFD1H
L21 [1 : 0]
8/16-bit compound timer ch.1 (Lower)
IRQ22
FFCEH
FFCFH
L22 [1 : 0]
Flash memory
IRQ23
FFCCH
FFCDH
L23 [1 : 0]
External interrupt ch.0
External interrupt ch.4
External interrupt ch.1
External interrupt ch.5
External interrupt ch.2
External interrupt ch.6
External interrupt ch.3
External interrupt ch.7
High
External interrupt ch.8
External interrupt ch.9
External interrupt ch.10
External interrupt ch.11
30
Low
MB95120 Series
■ ELECTRICAL CHARACTERISTICS
1. Absolute Maximum Ratings
Parameter
Symbol
1
Power supply voltage*
Power supply voltage for
LCD
Input voltage*1
Output voltage*
1
Maximum clamp current
Total maximum clamp
current
“L” level maximum
output current
Rating
Vcc
AVcc
Vss − 0.3
Vss + 4.0
AVR
Vss − 0.3
Vss + 4.0
*2
V0 to V3
VSS − 0.3
VSS + 4.0
Products with LCD internal division
resistance*3
V0
VSS − 0.3
VSS + 2.0
V1
VSS − 0.3
VSS + 2.0
V2
VSS − 0.3
VSS + 4.0
V3
VSS − 0.3
VSS + 6.0
C0, C1
VSS − 0.3
VSS + 6.0
VI1
Vss − 0.3
Vss + 4.0
VI2
Vss − 0.3
Vss + 6.0
VO
Vss − 0.3
Vss + 4.0
V
ICLAMP
− 2.0
+ 2.0
mA
Applicable to pins*5
Σ|ICLAMP|
⎯
20
mA
Applicable to pins*5
IOL1
IOL2
“L” level average
current
⎯
“H” level maximum
output current
15
15
V
⎯
Products with booster circuit* 3
V
mA
mA
12
ΣIOL
⎯
100
mA
ΣIOLAV
⎯
50
mA
IOH1
IOH2
⎯
− 15
− 15
*2
V
4
IOLAV2
“L” level total average
output current
Remarks
Max
IOLAV1
“L” level total maximum
output current
Unit
Min
mA
Other than P50, P51*4
P50, P51
*4
Other than P00 to P07
P00 to P07
Other than P00 to P07
Average output current =
operating current × operating ratio
(1 pin)
P00 to P07
Average output current =
operating current × operating ratio
(1 pin)
Total average output current =
operating current × operating ratio
(Total of pins)
Other than P00 to P07
P00 to P07
(Continued)
31
MB95120 Series
(Continued)
Parameter
Symbol
Rating
Min
⎯
mA
−8
IOHAV2
“H” level total maximum
output current
Unit
−4
IOHAV1
“H” level average
current
Max
ΣIOH
⎯
− 100
mA
ΣIOHAV
⎯
− 50
mA
Power consumption
Pd
⎯
320
mW
Operating temperature
TA
− 40
+ 85
°C
Tstg
− 55
+ 150
°C
“H” level total average
output current
Storage temperature
Remarks
Other than P00 to P07
Average output current =
operating current × operating ratio
(1 pin)
P00 to P07
Average output current =
operating current × operating ratio
(1 pin)
Total average output current =
operating current × operating ratio
(Total of pins)
*1 : The parameter is based on AVSS = VSS = 0.0 V.
*2 : Apply equal potential to AVcc and Vcc. AVR should not exceed AVcc + 0.3 V.
*3 : V0 to V3 should not exceed VCC + 0.3 V.
*4 : VI1 and Vo should not exceed VCC + 0.3 V. VI1 must not exceed the rating voltage. However, if the maximum
current to/from an input is limited by some means with external components, the ICLAMP rating supersedes the
VI1 rating.
*5 : Applicable to pins : P00 to P07, P10 to P14, P20 to P24, P30 to P37, P40 to P43, P52, P53
• Use within recommended operating conditions.
• Use at DC voltage (current).
• +B signal is an input signal that exceeds VCC voltage. The + B signal should always be applied a limiting
resistance placed between the + B signal and the microcontroller.
• The value of the limiting resistance should be set so that when the + B signal is applied the input current
to the microcontroller pin does not exceed rated values, either instantaneously or for prolonged periods.
• Note that when the microcontroller drive current is low, such as in the power saving modes, the +B input
potential may pass through the protective diode and increase the potential at the VCC pin, and this affects
other devices.
• Note that if the + B signal is inputted when the microcontroller power supply is off (not fixed at 0 V), the power
supply is provided from the pins, so that incomplete operation may result.
• Note that if the + B input is applied during power-on, the power supply is provided from the pins and the
resulting power supply voltage may not be sufficient to operate the power-on reset.
• Care must be taken not to leave the + B input pin open.
• Note that analog system input/output pins other than the A/D input pins (LCD drive pins, etc.) cannot accept
+B signal input.
32
MB95120 Series
• Sample recommended circuits :
• Input/Output Equivalent circuits
Protective diode
+ B input (0 V to 16 V)
Vcc
Limiting
resistance
P-ch
N-ch
R
WARNING: Semiconductor devices can be permanently damaged by application of stress (voltage, current,
temperature, etc.) in excess of absolute maximum ratings. Do not exceed these ratings.
33
MB95120 Series
2. Recommended Operating Conditions
(AVSS = VSS = 0.0 V)
Parameter
Power supply
voltage
Power supply
voltage for LCD
A/D converter
reference
input voltage
Operating
temperature
Symbol Pin name Condition
VCC,
AVCC
⎯
⎯
Value
Unit
Remarks
Min
Max
1.8*
3.3
At normal operation,
Flash memory product,
TA = −10 °C to +85 °C
2.0*
3.3
At normal operation,
Flash memory product,
TA = −40 °C to +85 °C
2.6
3.6
Evaluation product
TA = +5 °C to +35 °C
1.5
3.3
Holds condition in stop mode,
Flash memory product
The range of liquid crystal power
supply: without up-conversion
(The optimal value depends on
liquid crystal display elements
used.)
V
V0
to
V3
⎯
⎯
VSS
VCC
V
AVR
⎯
⎯
1.8
AVCC
V
TA
⎯
⎯
− 40
+ 85
°C
* : The values vary with the operating frequency, machine clock or analog guarantee range.
WARNING: The recommended operating conditions are required in order to ensure the normal operation of the
semiconductor device. All of the device’s electrical characteristics are warranted when the device is
operated within these ranges.
Always use semiconductor devices within their recommended operating condition ranges. Operation
outside these ranges may adversely affect reliability and could result in device failure.
No warranty is made with respect to uses, operating conditions, or combinations not represented on
the data sheet. Users considering application outside the listed conditions are advised to contact their
FUJITSU representatives beforehand.
34
MB95120 Series
3. DC Characteristics
(VCC = AVCC = 3.3 V, AVSS = VSS = 0.0 V, TA = − 40 °C to + 85 °C)
Parameter
“H” level input
voltage
“L” level input
voltage
“L” level input
voltage
Open-drain
output
application
voltage
Value
Symbol
Pin name
Conditions
Min
Typ
Max
VIH1
P10 (selectable at UI0) ,
P67 (selectable at SIN)
⎯
0.7 VCC
⎯
VIH2
P50, P51
(selectable at I2C)
⎯
0.7 VCC
VIHS1
P00 to P07, P10 to P14,
P20 to P24, P30 to P37,
P40 to P43, P50 to P53,
P60 to P67, P70, P71,
P90 to P95,
PA0 to PA3,
PB0 to PB7,
PC0 to PC7,
PD0 to PD7,
PE0 to PE7
⎯
VIHS2
P50, P51
VIHM
RST, MOD
Unit
Remarks
VCC + 0.3
V
⎯
VSS + 5.5
V
When selecting
CMOS input level
(Hysteresis input)
0.8 VCC
⎯
VCC + 0.3
V
Hysteresis input
⎯
0.8 VCC
⎯
VSS + 5.5
V
⎯
0.8 VCC
⎯
VCC + 0.3
V
Hysteresis input
VIL
P10 (selectable at UI0) ,
P50, P51
(selectable at I2C)
P67 (selectable at SIN)
⎯
VSS − 0.3
⎯
0.3 VCC
V
When selecting
CMOS input level
(Hysteresis input)
VILS
P00 to P07
P10 to P14,
P20 to P24,
P30 to P37,
P40 to P43,
P50 to P53,
P60 to P67,
P70, P71,
P90 to P95,
PA0 to PA3,
PB0 to PB7,
PC0 to PC7,
PD0 to PD7,
PE0 to PE7
⎯
VSS − 0.3
⎯
0.2 VCC
V
Hysteresis input
VILM
RST, MOD
⎯
VSS − 0.3
⎯
0.2 VCC
V
Hysteresis input
VD1
P50, P51
⎯
VSS − 0.3
⎯
VSS + 5.5
V
(Continued)
35
MB95120 Series
(VCC = AVCC = 3.3 V, AVSS = VSS = 0.0 V, TA = − 40 °C to + 85 °C)
Parameter
Symbol
“H” level output
voltage
VOH1
VOH2
P00 to P07
VOL1
VOL2
“L” level output
voltage
Pin name
Conditions
Value
Unit
Min
Typ
Max
Output pin other
IOH = − 4.0 mA
than P00 to P07
2.4
⎯
⎯
V
IOH = − 8.0 mA
2.4
⎯
⎯
V
Output pin other
than P00 to
IOL = 4.0 mA
P07, RST
⎯
⎯
0.4
V
P00 to P07
IOL = 12 mA
⎯
⎯
0.4
V
Port other than
P50, P51
0.0 V < VI <
VCC
−5
⎯
+5
µA
Input leakage
current (Hi-Z
output leakage
current)
ILI
Open-drain
output leakage
current
ILIOD
P50, P51
0.0 V < VI <
VSS + 5.5 V
⎯
⎯
5
µA
RPULL
P10 to P14,
P20 to P24,
P30 to P37,
P40 to P43,
P52, P53,
P70, P71
VI = 0.0 V
25
50
100
kΩ
Other than
AVCC, AVSS,
AVR, VCC, VSS
f = 1 MHz
⎯
5
15
pF
Pull-up resistor
Input
capacitance
CIN
Remarks
When the pull-up
prohibition setting
When the pull-up
permission setting
(Continued)
36
MB95120 Series
(VCC = AVCC = 3.3 V, AVSS = VSS = 0.0 V, TA = − 40 °C to + 85 °C)
Parameter
Symbol
Pin name
Conditions
FCH = 20 MHz
FMP = 10 MHz
Main clock mode
(divided by 2)
Value
Min
Typ
Max
Unit
Remarks
⎯
11.0
14.0
At other than
Flash memory
mA
writing and
erasing
⎯
30.0
35.0
At Flash
mA memory writing
and erasing
ICC
⎯
17.6
22.4
At other than
Flash memory
mA
writing and
erasing
⎯
38.1
44.9
At Flash
mA memory writing
and erasing
FCH = 20 MHz
FMP = 10 MHz
Main Sleep mode
(divided by 2)
⎯
4.5
6.0
mA
FCH = 32 MHz
FMP = 16 MHz
Main Sleep mode
(divided by 2)
⎯
7.2
9.6
mA
ICCL
FCL = 32 kHz
FMPL = 16 kHz
Sub clock mode
(divided by 2)
⎯
25
35
µA
ICCLS
FCL = 32 kHz
FMPL = 16 kHz
Sub sleep mode
(divided by 2)
⎯
7
15
µA
ICCT
FCL = 32 kHz
Watch mode
Main stop mode
TA = + 25 °C
⎯
2
10
µA
FCH = 4 MHz
FMP = 10 MHz
Main PLL mode
(multiplied by 2.5)
⎯
10
14
mA
FCH = 6.4 MHz
FMP = 16 MHz
Main PLL mode
(multiplied by 2.5)
⎯
16.0
22.4
mA
FCH = 32 MHz
FMP = 16 MHz
Main clock mode
(divided by 2)
ICCS
VCC
(External clock
operation)
Power supply
current*
ICCMPLL
(Continued)
37
MB95120 Series
(Continued)
Parameter
(VCC = AVCC = 3.3 V, AVSS = VSS = 0.0 V, TA = − 40 °C to + 85 °C)
Symbol
Pin name
ICCSPLL
ICTS
Power supply
current*
VCC
(External clock
operation)
ICCH
IA
AVCC
IAH
Value
Typ
Max
FCL = 32 kHz
FMPL = 128 kHz
Sub PLL mode
(multiplied by 4) ,
TA = + 25 °C
⎯
190
250
µA
FCH = 10 MHz
Timebase timer mode
TA = + 25 °C
⎯
0.4
0.5
mA
Sub stop mode
TA = + 25 °C
⎯
1
5
µA
FCH = 16 MHz
At operating of A/D
conversion
⎯
1.3
2.2
mA
FCH = 16 MHz
At stopping of A/D
conversion
TA = + 25 °C
⎯
1
5
µA
Remarks
⎯
300
⎯
⎯
⎯
±1
µA
V1 = 1.5 V
4.3
4.5
4.7
V
V2
V1 = 1.5 V
2.9
3.0
3.1
V
VV1
V1
IIN = 0.0 µA
1.4
1.5
1.7
V
RRIN
V1
8.5
9.8
11
kΩ
⎯
⎯
5
kΩ
RLCD
⎯
LCD leakage
current
ILCDL
V0 to V3,
COM0 to COM3
SEG00 to SEG39
VV3
V3
VV2
Reference
voltage for
LCD boost
Reference
voltage input
impedance
Between V3 and VSS
⎯
⎯
COM0 to
COM3 output
impedance
RVCOM COM0 to COM3
SEG00 to
SEG39 output
impedance
RVSEG SEG00 to SEG39
⎯
⎯
⎯
7
kΩ
LCD leak
current
ILCDL
V0 to V3,
COM0 to COM3
SEG00 to SEG39
⎯
−1
⎯
+1
µA
V1 to V3 = 3.6 V
* : The power-supply current is determined by the external clock.
• Refer to “4. AC characteristics (1) Clock Timing” for FCH and FCL.
• Refer to “4. AC characteristics (2) Source Clock/Machine Clock” for FMP and FMPL.
38
Unit
Min
Products with
LCD internal
kΩ
division
resistance only
LCD internal
division
resistance
Output voltage
for LCD boost
Conditions
Products with
booster circuit
only
MB95120 Series
4. AC Characteristics
(1) Clock Timing
(VCC = 3.3 V, AVSS = VSS = 0.0 V, TA = − 40 °C to + 85 °C)
Parameter
SymCondiPin name
bol
tions
FCH
X0, X1
Clock frequency
FCL
X0, X1
Clock cycle time
Input clock pulse width
Input clock rise time and
fall time
Unit
Remarks
16.25
MHz
When using main
oscillation circuit
⎯
32.50
MHz When using external clock
3.00
⎯
10.00
MHz Main PLL multiplied by 1
3.00
⎯
8.13
MHz Main PLL multiplied by 2
3.00
⎯
6.50
MHz Main PLL multiplied by 2.5
3.00
⎯
4.06
MHz Main PLL multiplied by 4
⎯
32.768
⎯
kHz
When using sub
oscillation circuit
⎯
32.768
⎯
kHz
When using sub PLL
VCC = 2.3 V to 3.3 V
61.5
⎯
1000
ns
When using main
oscillation circuit
30.8
⎯
1000
ns
When using external clock
Min
Typ
Max
1.00
⎯
1.00
X0A, X1A
⎯
tHCYL
Value
tLCYL
X0A, X1A
⎯
30.5
⎯
µs
When using sub
oscillation circuit
tWH1
tWL1
X0
61.5
⎯
⎯
ns
tWH2
tWL2
X0A
⎯
15.2
⎯
µs
When using external clock
Duty ratio is about 30% to
70%.
tCR
tCF
X0, X0A
⎯
⎯
5
ns
When using external clock
39
MB95120 Series
• Input wave form for using external clock (main clock)
tHCYL
tWH1
tWL1
tCR
tCF
0.8 VCC 0.8 VCC
X0
0.2 VCC
0.2 VCC
0.2 VCC
• Figure of Main Clock Input Port External Connection
When using a crystal or
ceramic oscillator
When using external clock
Microcontroller
Microcontroller
X0
X1
X0
X1
Open
FCH
FCH
C1
C2
• Input wave form for using external clock (sub clock)
tLCYL
tWH2
tCR
tWL2
tCF
0.8 VCC 0.8 VCC
X0A
0.1 VCC
0.1 VCC
0.1 VCC
• Figure of Sub clock Input Port External Connection
When using a crystal or
ceramic oscillator
Microcontroller
X0A
X1A
When using external clock
Microcontroller
X0A
FCL
X1A
Open
FCL
C1
40
C2
MB95120 Series
(2) Source Clock/Machine Clock
(VCC = 3.3 V, AVSS = VSS = 0.0 V, TA = − 40 °C to + 85 °C)
SymPin
bol name
Parameter
Value
Min
Typ
⎯
61.5
Max
2000
Unit
ns
When using main clock
Min : FCH = 16.25 MHz,
PLL multiplied by 1
Max : FCH = 1 MHz, divided by 2
µs
When using sub clock
Min : FCL = 32 kHz,
PLL multiplied by 4
Max : FCL = 32 kHz, divided by 2
1
Source clock cycle time*
(Clock before setting
division)
Source clock frequency
Machine clock cycle time*2
(Minimum instruction
execution time)
Machine clock frequency
tSCLK
⎯
7.6
⎯
61.0
16.25
Remarks
FSP
⎯
0.50
⎯
FSPL
⎯
16.384
⎯
61.5
⎯
32000
ns
When using main clock
Min : FSP = 16.25 MHz, no division
Max : FSP = 0.5 MHz, divided by 16
7.6
⎯
976.5
µs
When using sub clock
Min : FSPL = 131 kHz, no division
Max : FSPL = 16 kHz, divided by 16
0.031
⎯
16.250
1.024
⎯
131.072 kHz When using sub clock
tMCLK
FMP
FMPL
MHz When using main clock
131.072 kHz When using sub clock
⎯
⎯
MHz When using main clock
*1 : Clock before setting division due to machine clock division ratio selection bit (SYCC : DIV1 and DIV0) . This
source clock is divided by the machine clock division ratio selection bit (SYCC : DIV1 and DIV0) , and it becomes
the machine clock. Further, the source clock can be selected as follows.
• Main clock divided by 2
• PLL multiplication of main clock (select from 1, 2, 2.5, 4 multiplication)
• Sub clock divided by 2
• PLL multiplication of sub clock (select from 2, 3, 4 multiplication)
*2 : Operation clock of the microcontroller. Machine clock can be selected as follows.
• Source clock (no division)
• Source clock divided by 4
• Source clock divided by 8
• Source clock divided by 16
• Outline of clock generation block
FCH
(main oscillation)
Divided by 2
Main PLL
×1
×2
× 2.5
×4
SCLK
(source clock)
FCL
(sub oscillation)
Divided by 2
Sub PLL
×2
×3
×4
Division
circuit
×1
× 1/4
× 1/8
× 1/16
MCLK
(machine clock)
Clock mode select bit
(SYCC: SCS1, SCS0)
41
MB95120 Series
• Operating voltage - Operating frequency (When TA = − 10 °C to + 85 °C)
• MB95F128D/F128E
Main clock mode and main PLL mode
operation guarantee range
3.6
3.6
Operating voltage (V)
Operating voltage (V)
Sub clock mode and watch mode
operation guarantee range
2.3
1.8
16.384 kHz
32 kHz
2.7
1.8
0.5 MHz 3 MHz
131.072 kHz
5 MHz
16.25 MHz
PLL operation guarantee range
PLL operation guarantee range
Main clock operation guarantee range
Source clock frequency (FSP)
Source clock frequency (FSPL)
• Operating voltage - Operating frequency (TA = − 40 °C to + 85 °C)
• MB95F128D/F128E
Sub PLL operation guarantee range
Sub clock mode and watch mode
operation guarantee range
Main clock mode and main PLL mode
operation guarantee range
3.3
Operating voltage (V)
Operating voltage (V)
3.3
2.3
2.0
16.384 kHz
32 kHz
131.072 kHz
PLL operation guarantee range
2.7
2.0
0.5 MHz 3 MHz
7.5 MHz
16.25 MHz
PLL operation guarantee range
Main clock operation guarantee range
Source clock frequency (FSPL)
42
Source clock frequency (FSP)
MB95120 Series
• Operating voltage - Operating frequency (TA = + 5 °C to + 35 °C)
• MB95FV100D-101/102
FRAM, Main clock mode and main PLL
mode operation guarantee range
Sub PLL, Sub clock mode and watch
mode operation guarantee range
3.6
2.6
16.384 kHz
32 kHz
131.072 kHz
PLL operation guarantee range
Operating voltage (V)
Operating voltage (V)
3.6
3.3
2.6
0.5 MHz 3 MHz
10 MHz
16.25 MHz
PLL operation guarantee range
Main clock operation guarantee range
Source clock frequency (FSPL)
Source clock frequency (FSP)
43
MB95120 Series
• Main PLL operation frequency
[MHz]
16.25
16
15
×4
12
Source clock frequency (Fsp)
× 2.5
10
×1
×2
7.5
6
5
3
0
3
4 4.062
5
6.4 6.5
Machine clock frequency (FMP)
44
8 8.125
10 [MHz]
MB95120 Series
(3) External Reset
(VCC = 3.3 V, AVSS = VSS = 0.0 V, TA = − 40 °C to + 85 °C)
Parameter
Value
Symbol
RST “L” level pulse
width
tRSTL
Unit
Remarks
Min
Max
2 tMCLK*1
⎯
ns
At normal operating
Oscillation time of oscillator*2
+ 2 tMCLK
⎯
µs
At stop mode, sub clock mode,
sub sleep mode, and watch mode
*1 : Refer to “ (2) Source Clock/Machine Clock” for tMCLK.
*2 : Oscillation start time of oscillator is the time that the amplitude reaches 90 %. In the crystal oscillator, the
oscillation time is between several ms and tens of ms. In ceramic oscillators, the oscillation time is between
hundreds of µs and several ms. In the external clock, the oscillation time is 0 ms.
• At normal operating
tRSTL
RST
0.2 VCC
0.2 VCC
• At stop mode, sub clock mode, sub sleep mode, watch mode, and power-on
RST
tRSTL
0.2 VCC
0.2 VCC
90% of
amplitude
X0
Internal
operating
clock
2 tMCLK
Oscillation time Oscillation stabilization wait time
of oscillator
Execute instruction
Internal reset
45
MB95120 Series
(4) Power-on Reset
(AVSS = VSS = 0.0 V, TA = − 40 °C to + 85 °C)
Parameter
Symbol
Conditions
Power supply rising time
tR
Power supply cutoff time
tOFF
tR
Value
Unit
Min
Max
⎯
⎯
36
ms
⎯
1
⎯
ms
Remarks
Waiting time until
power-on
tOFF
1.5 V
VCC
0.2 V
0.2 V
0.2 V
Note : Sudden change of power supply voltage may activate the power-on reset function. When changing power
supply voltages during operation, set the slope of rising within 30 mV/ms as shown below.
VCC
Limiting the slope of rising within
20 mV/ms is recommended.
1.5 V
Hold Condition in stop mode
VSS
46
MB95120 Series
(5) Peripheral Input Timing
(VCC = 3.3 V, AVSS = VSS = 0.0 V, TA = − 40 °C to + 85 °C)
Parameter
Value
Symbol
Pin name
Peripheral input “H” pulse
width
tILIH
Peripheral input “L” pulse
width
tIHIL
INT00 to INT07,
INT10 to INT13,
EC0, EC1, TI0, TRG0/ADTG, TRG1
Unit
Min
Max
2 tMCLK*
⎯
ns
2 tMCLK*
⎯
ns
* : Refer to “ (2) Source Clock/Machine Clock” for tMCLK.
tILIH
INT00 to INT07,
INT10 to INT13, EC0, EC1,
TI0, TRG0/ADTG, TRG1
tIHIL
0.8 VCC 0.8 VCC
0.2 VCC
0.2 VCC
47
MB95120 Series
(6) UART/SIO, Serial I/O Timing
(VCC = 3.3 V, AVSS = VSS = 0.0 V, TA = − 40 °C to + 85 °C)
Parameter
Symbol
Pin name
Serial clock cycle time
tSCYC
UCK0
UCK ↓ → UO time
tSLOV
UCK0, UO0
Valid UI → UCK ↑
tIVSH
UCK0, UI0
UCK ↑ → valid UI hold time
tSHIX
Serial clock “H” pulse width
Value
Conditions
Max
4 tMCLK*
⎯
ns
− 190
+190
ns
2 tMCLK*
⎯
ns
UCK0, UI0
2 tMCLK*
⎯
ns
tSHSL
UCK0
4 tMCLK*
⎯
ns
Serial clock “L” pulse width
tSLSH
UCK0
4 tMCLK*
⎯
ns
UCK ↓ → UO time
tSLOV
UCK0, UO0
0
190
ns
Valid UI → UCK ↑
tIVSH
UCK0, UI0
2 tMCLK*
⎯
ns
UCK ↑ → valid UI hold time
tSHIX
UCK0, UI0
2 tMCLK*
⎯
ns
Internal clock
operation output pin :
CL = 80 pF + 1TTL.
External clock
operation output pin :
CL = 80 pF + 1TTL.
* : Refer to “ (2) Source Clock/Machine Clock” for tMCLK.
• Internal shift clock mode
tSCYC
UCK0
2.4 V
0.8 V
0.8 V
tSLOV
UO0
UI0
2.4 V
0.8 V
tIVSH
tSHIX
0.8 VCC
0.2 VCC
0.8 VCC
0.2 VCC
• External shift clock mode
tSLSH
tSHSL
0.8 VCC 0.8 VCC
UCK0
0.2 VCC 0.2 VCC
tSLOV
UO0
UI0
48
Unit
Min
2.4 V
0.8 V
tIVSH
tSHIX
0.8 VCC
0.2 VCC
0.8 VCC
0.2 VCC
MB95120 Series
(7) LIN-UART Timing
Sampling at the rising edge of sampling clock*1 and prohibited serial clock delay*2
(ESCR register : SCES bit = 0, ECCR register : SCDE bit = 0)
(VCC = 3.3 V, AVSS = VSS = 0.0 V, TA = −40 °C to + 85 °C)
Parameter
Serial clock cycle time
SCK ↓ → SOT delay time
SymPin name
bol
tSCYC
tSLOVI
Valid SIN → SCK ↑
tIVSHI
SCK ↑ → valid SIN hold time
tSHIXI
Serial clock “L” pulse width
tSLSH
Serial clock “H” pulse width
tSHSL
Value
Conditions
Max
5 tMCLK*3
⎯
ns
−95
+95
ns
⎯
ns
0
⎯
ns
3 tMCLK*3 − tR
⎯
ns
* + 95
⎯
ns
SCK
Internal clock
SCK, SOT
operation output pin :
SCK, SIN CL = 80 pF + 1 TTL.
SCK, SIN
SCK
SCK
SCK ↓ → SOT delay time
tSLOVE SCK, SOT
Valid SIN → SCK ↑
tIVSHE
SCK ↑ → valid SIN hold time
tSHIXE
External clock
SCK, SIN operation output pin :
CL = 80 pF + 1 TTL.
SCK, SIN
Unit
Min
t
* + 190
MCLK 3
MCLK 3
t
⎯
* + 95
MCLK 3
ns
190
⎯
ns
tMCLK*3 + 95
⎯
ns
2t
SCK fall time
tF
SCK
⎯
10
ns
SCK rise time
tR
SCK
⎯
10
ns
*1 : Provide switch function whether sampling of reception data is performed at rising edge or falling edge of the
serial clock.
*2 : Serial clock delay function is used to delay half clock for the output signal of serial clock.
*3 : Refer to “ (2) Source Clock/Machine Clock” for tMCLK.
49
MB95120 Series
• Internal shift clock mode
tSCYC
2.4 V
SCK
0.8 V
0.8 V
tSLOVI
2.4 V
SOT
0.8 V
tIVSHI
tSHIXI
0.8 VCC 0.8 VCC
SIN
0.2 VCC 0.2 VCC
• External shift clock mode
tSLSH
SCK
0.8 VCC
0.2 VCC
tF
SOT
tSHSL
0.8 VCC
0.2 VCC
tR
tSLOVE
2.4 V
0.8 V
tIVSHE
SIN
tSHIXE
0.8 VCC 0.8 VCC
0.2 VCC 0.2 VCC
50
0.8 VCC
MB95120 Series
Sampling at the falling edge of sampling clock*1 and prohibited serial clock delay*2
(ESCR register : SCES bit = 1, ECCR register : SCDE bit = 0)
(VCC = 3.3 V, AVSS = VSS = 0.0 V, TA = −40 °C to + 85 °C)
Symbol
Pin name
Serial clock cycle time
tSCYC
SCK
SCK ↑ → SOT delay time
tSHOVI
SCK, SOT
Parameter
Value
Conditions
Internal clock
operation output pin :
SCK, SIN CL = 80 pF + 1 TTL.
SCK, SIN
Unit
Min
Max
5 tMCLK*3
⎯
ns
−95
+95
ns
⎯
ns
0
⎯
ns
* + 190
Valid SIN → SCK ↓
tIVSLI
SCK ↓ → valid SIN hold time
tSLIXI
Serial clock “H” pulse width
tSHSL
SCK
3 tMCLK*3 − tR
⎯
ns
Serial clock “L” pulse width
tSLSH
SCK
tMCLK*3 + 95
⎯
ns
SCK, SOT
⎯
SCK ↑ → SOT delay time
tSHOVE
Valid SIN → SCK ↓
tIVSLE
SCK ↓ → valid SIN hold time
tSLIXE
External clock
SCK, SIN operation output pin :
SCK, SIN CL = 80 pF + 1 TTL.
t
MCLK 3
* + 95
MCLK 3
ns
190
⎯
ns
tMCLK*3 + 95
⎯
ns
2t
SCK fall time
tF
SCK
⎯
10
ns
SCK rise time
tR
SCK
⎯
10
ns
*1 : Provide switch function whether sampling of reception data is performed at rising edge or falling edge of the
serial clock.
*2 : Serial clock delay function is used to delay half clock for the output signal of serial clock.
*3 : Refer to “ (2) Source Clock/Machine Clock” for tMCLK.
51
MB95120 Series
• Internal shift clock mode
tSCYC
2.4 V
2.4 V
SCK
0.8 V
tSHOVI
2.4 V
SOT
0.8 V
tIVSLI
tSLIXI
0.8 VCC 0.8 VCC
SIN
0.2 VCC 0.2 VCC
• External shift clock mode
tSHSL
SCK
0.8 VCC
tSLSH
0.8 VCC
0.2 VCC
tR
SOT
0.2 VCC
tF
tSHOVE
2.4 V
0.8 V
tIVSLE
SIN
tSLIXE
0.8 VCC 0.8 VCC
0.2 VCC 0.2 VCC
52
0.2 VCC
MB95120 Series
Sampling at the rising edge of sampling clock*1 and enabled serial clock delay*2
(ESCR register : SCES bit = 0, ECCR register : SCDE bit = 1)
(VCC = 3.3 V, AVSS = VSS = 0.0 V, TA = −40 °C to + 85 °C)
Symbol
Pin name
Serial clock cycle time
tSCYC
SCK
SCK ↑ → SOT delay time
tSHOVI
SCK, SOT
Parameter
Valid SIN → SCK ↓
tIVSLI
SCK, SIN
SCK ↓ → valid SIN hold time
tSLIXI
SCK, SIN
SOT → SCK ↓ delay time
tSOVLI
SCK, SOT
Value
Conditions
Internal clock
operation output pin :
CL = 80 pF + 1 TTL.
Unit
Min
Max
5 tMCLK*3
⎯
ns
−95
+95
ns
⎯
ns
0
⎯
ns
⎯
4 tMCLK*3
ns
* + 190
MCLK 3
t
*1 : Provide switch function whether sampling of reception data is performed at rising edge or falling edge of the
serial clock.
*2 : Serial clock delay function is used to delay half clock for the output signal of serial clock.
*3 : Refer to “ (2) Source Clock/Machine Clock” for tMCLK.
tSCYC
2.4 V
SCK
0.8 V
SOT
2.4 V
0.8 V
2.4 V
0.8 V
tIVSLI
SIN
0.8 V
tSHOVI
tSOVLI
0.8 VCC
0.2 VCC
tSLIXI
0.8 VCC
0.2 VCC
53
MB95120 Series
Sampling at the falling edge of sampling clock*1 and enabled serial clock delay*2
(ESCR register : SCES bit = 1, ECCR register : SCDE bit = 1)
(VCC = 3.3 V, AVSS = VSS = 0.0 V, TA = −40 °C to + 85 °C)
Symbol
Pin name
Serial clock cycle time
tSCYC
SCK ↓ → SOT delay time
tSLOVI
Parameter
Value
Conditions
Unit
Min
Max
SCK
5 tMCLK*3
⎯
ns
SCK, SOT
−95
+95
ns
⎯
ns
0
⎯
ns
⎯
4 tMCLK*3
ns
Valid SIN → SCK ↑
tIVSHI
SCK ↑ → valid SIN hold time
tSHIXI
Internal clock
SCK, SIN operating output pin :
CL = 80 pF + 1 TTL.
SCK, SIN
SOT → SCK ↑ delay time
tSOVHI
SCK, SOT
t
* + 190
MCLK 3
*1 : Provide switch function whether sampling of reception data is performed at rising edge or falling edge of the
serial clock.
*2 : Serial clock delay function is used to delay half clock for the output signal of serial clock.
*3 : Refer to “ (2) Source Clock/Machine Clock” for tMCLK.
tSCYC
2.4 V
SCK
2.4 V
0.8 V
tSOVHI
SOT
2.4 V
0.8 V
tIVSHI
SIN
54
tSLOVI
2.4 V
0.8 V
tSHIXI
0.8 VCC
0.8 VCC
0.2 VCC
0.2 VCC
MB95120 Series
(8) I2C Timing
(VCC = 3.3 V, AVSS = VSS = 0.0 V, TA = − 40 °C to + 85 °C)
Value
Parameter
Symbol
Pin
name
Conditions Standard-mode
Fast-mode
Min
Max
Min
Max
Unit
fSCL
SCL0
0
100
0
400
kHz
tHD;STA
SCL0
SDA0
4.0
⎯
0.6
⎯
µs
SCL clock “L” width
tLOW
SCL0
4.7
⎯
1.3
⎯
µs
SCL clock “H” width
tHIGH
SCL0
4.0
⎯
0.6
⎯
µs
(Repeat) Start condition setup time
SCL ↑ → SDA ↓
tSU;STA
SCL0
SDA0
4.7
⎯
0.6
⎯
µs
Data hold time SCL ↓ → SDA ↓ ↑
tHD;DAT
SCL0
SDA0
0
3.45*2
0
0.9*3
µs
Data setup time SDA ↓ ↑ → SCL ↑
tSU;DAT
SCL0
SDA0
0.25
⎯
0.1
⎯
µs
Stop condition setup time SCL ↑ →
SDA ↑
tSU;STO
SCL0
SDA0
4.0
⎯
0.6
⎯
µs
tBUF
SCL0
SDA0
4.7
⎯
1.3
⎯
µs
SCL clock frequency
(Repeat) Start condition hold time
SDA ↓ → SCL ↓
Bus free time between stop
condition and start condition
R = 1.7 kΩ,
C = 50 pF*1
*1 : R, C : Pull-up resistor and load capacitor of the SCL and SDA lines.
*2 : The maximum tHD;DAT have only to be met if the device dose not stretch the “L” width (tLOW) of the SCL signal.
*3 : A fast-mode I2C-bus device can be used in a standard-mode I2C-bus system, but the requirement
tSU;DAT ≥ 250 ns must then be met.
tWAKEUP
SDA0
tLOW
tHD;DAT
tHIGH
tHD;STA
tBUF
SCL0
tHD;STA
tSU;DAT
fSCL
tSU;STA
tSU;STO
55
MB95120 Series
(VCC = 3.3 V, AVSS = VSS = 0.0 V, TA = −40 °C to + 85 °C)
Parameter
Sym- Pin
bol name
Conditions
Value*2
Min
Max
Unit
Remarks
SCL clock
“L” width
tLOW
SCL0
(2 + nm / 2) tMCLK − 20
⎯
ns
Master mode
SCL clock
“H” width
tHIGH
SCL0
(nm / 2) tMCLK − 20
(nm / 2 ) tMCLK + 20
ns
Master mode
Start condition
SCL0
tHD;STA
hold time
SDA0
(−1 + nm / 2) tMCLK − 20
(−1 + nm) tMCLK + 20
ns
Master mode
Maximum value is
applied when m,
n = 1, 8.
Otherwise, the
minimum value is
applied.
Stop condition
SCL0
tSU;STO
setup time
SDA0
(1 + nm / 2) tMCLK − 20
(1 + nm / 2) tMCLK + 20
ns
Master mode
Start condition
SCL0
tSU;STA
setup time
SDA0
(1 + nm / 2) tMCLK − 20
(1 + nm / 2) tMCLK + 20
ns
Master mode
SCL0
SDA0
(2 nm + 4) tMCLK − 20
⎯
ns
SCL0
SDA0
3 tMCLK − 20
⎯
ns
Master mode
ns
Master mode
When assuming
that “L” of SCL is
not extended, the
minimum value is
applied to first bit
of continuous
data.
Otherwise,
the maximum
value is applied.
Bus free time
between stop
condition and
start condition
tBUF
Data hold time tHD;DAT
R = 1.7 kΩ,
C = 50 pF*1
Data setup
time
Setup time
between
clearing
interrupt and
SCL rising
tSU;DAT
SCL0
SDA0
tSU;INT SCL0
(−2 + nm / 2) tMCLK − 20 (−1 + nm / 2) tMCLK + 20
(nm / 2) tMCLK − 20
(1 + nm / 2) tMCLK + 20
ns
Minimum value is
applied to interrupt
at 9th SCL↓.
Maximum value is
applied to interrupt
at 8th SCL↓.
SCL clock “L”
width
tLOW
SCL0
4 tMCLK − 20
⎯
ns
At reception
SCL clock “H”
width
tHIGH
SCL0
4 tMCLK − 20
⎯
ns
At reception
Start condition
SCL0
tHD;STA
detection
SDA0
2 tMCLK − 20
⎯
ns
Undetected when
1 tMCLK is used at
reception
(Continued)
56
MB95120 Series
(Continued)
Parameter
(VCC = 3.3 V, AVSS = VSS = 0.0 V, TA = −40 °C to + 85 °C)
Sym- Pin
bol name
Conditions
Value*2
Min
Max
Unit
Remarks
Stop condition
detection
tSU;STO
SCL0
SDA0
2 tMCLK − 20
⎯
ns
Undetected when
1 tMCLK is used at
reception
Restart condition
detection condition
tSU;STA
SCL0
SDA0
2 tMCLK − 20
⎯
ns
Undetected when
1 tMCLK is used at
reception
Bus free time
tBUF
SCL0
SDA0
2 tMCLK − 20
⎯
ns
At reception
Data hold time
tHD;DAT
2 tMCLK − 20
⎯
ns
At slave transmission
mode
Data setup time
tSU;DAT
SCL0
SDA0 R = 1.7 kΩ,
1
SCL0 C = 50 pF*
tLOW − 3 tMCLK − 20
⎯
ns
At slave transmission
mode
Data hold time
tHD;DAT
SCL0
SDA0
0
⎯
ns
At reception
Data setup time
tSU;DAT
SCL0
SDA0
tMCLK − 20
⎯
ns
At reception
SDA↓→SCL↑
(at wakeup function)
tWAKE-
SCL0
SDA0
Oscillation
stabilization
wait time +
2 tMCLK − 20
⎯
ns
UP
SDA0
*1 : R, C : Pull-up resistor and load capacitor of the SCL and SDA lines.
*2 : •
•
•
•
Refer to “ (2) Source Clock/Machine Clock” for tMCLK.
m is CS4 bit and CS3 bit (bit 4 and bit 3) of I2C clock control register (ICCR) .
n is CS2 bit to CS0 bit (bit 2 to bit 0) of I2C clock control register (ICCR) .
Actual timing of I2C is determined by m and n values set by the machine clock (tMCLK) and CS4 to CS0 of
ICCR0 register.
• Standard-mode :
m and n can be set at the range : 0.9 MHz < tMCLK (machine clock) < 10 MHz.
Setting of m and n determines the machine clock that can be used below.
(m, n) = (1, 8)
: 0.9 MHz < tMCLK ≤ 1 MHz
(m, n) = (1, 22) , (5, 4) , (6, 4) , (7, 4) , (8, 4) : 0.9 MHz < tMCLK ≤ 2 MHz
(m, n) = (1, 38) , (5, 8) , (6, 8) , (7, 8) , (8, 8) : 0.9 MHz < tMCLK ≤ 4 MHz
(m, n) = (1, 98)
: 0.9 MHz < tMCLK ≤ 10 MHz
• Fast-mode :
m and n can be set at the range : 3.3 MHz < tMCLK (machine clock) < 10 MHz.
Setting of m and n determines the machine clock that can be used below.
(m, n) = (1, 8)
: 3.3 MHz < tMCLK ≤ 4 MHz
(m, n) = (1, 22) , (5, 4)
: 3.3 MHz < tMCLK ≤ 8 MHz
(m, n) = (6, 4)
: 3.3 MHz < tMCLK ≤ 10 MHz
57
MB95120 Series
5. A/D Converter
(1) A/D Converter Electrical Characteristics
(AVcc = Vcc = 1.8 V to 3.3 V, AVss = Vss = 0.0 V, TA = − 40 °C to + 85 °C)
Parameter
Symbol
Resolution
Total error
Linearity error
⎯
Differential linear error
Zero transition voltage
Full-scale transition
voltage
Compare time
Value
Typ
Max
⎯
⎯
10
bit
− 3.0
⎯
+ 3.0
LSB
− 2.5
⎯
+ 2.5
LSB
− 1.9
⎯
+ 1.9
LSB
V
2.7 V ≤ AVcc ≤
3.3 V
AVss − 0.5 LSB AVss + 1.5 LSB AVss + 3.5 LSB
V
1.8 V ≤ AVcc <
2.7 V
AVR − 3.5 LSB AVR − 1.5 LSB AVR + 0.5 LSB
V
2.7 V ≤ AVcc ≤
3.3 V
AVR − 2.5 LSB AVR − 0.5 LSB AVR + 1.5 LSB
V
1.8 V ≤ AVcc <
2.7 V
0.6
⎯
140
µs
2.7 V ≤ AVcc ≤
3.3 V
20
⎯
140
µs
1.8 V ≤ AVcc <
2.7 V
µs
2.7 V ≤ AVcc ≤
3.3 V,
At external
impedance < 1.8 kΩ
1.8 V ≤ AVcc <
2.7 V,
At external
impedance <
14.8 kΩ
VOT
VFST
⎯
⎯
∞
⎯
30
⎯
∞
µs
Analog input current
IAIN
−0.3
⎯
+0.3
µA
Analog input voltage
VAIN
AVss
⎯
AVR
V
⎯
AVss + 1.8
⎯
AVcc
V
AVR pin
IR
⎯
400
600
µA
AVR pin,
During A/D
operation
IRH
⎯
⎯
5
µA
AVR pin,
At stop mode
Reference voltage
Reference voltage
supply current
58
Remarks
AVss − 1.5 LSB AVss + 0.5 LSB AVss + 2.5 LSB
0.4
Sampling time
Unit
Min
MB95120 Series
(2) Notes on Using A/D Converter
• About the external impedance of analog input and its sampling time
A/D converter with sample and hold circuit. If the external impedance is too high to keep sufficient sampling
time, the analog voltage charged to the internal sample and hold capacitor is insufficient, adversely affecting
A/D conversion precision. Therefore to satisfy the A/D conversion precision standard, consider the relationship
between the external impedance and minimum sampling time and either adjust the register value and operating
frequency or decrease the external impedance so that the sampling time is longer than the minimum value. Also,
if the sampling time cannot be sufficient, connect a capacitor of about 0.1 µF to the analog input pin.
• Analog input equivalent circuit
R
Analog input
Comparator
C
During sampling : ON
R
1.7 kΩ (Max)
84 kΩ (Max)
2.7 V ≤ AVcc ≤ 3.6 V
1.8 V ≤ AVcc < 2.7 V
C
14.5 pF (Max)
25.2 pF (Max)
Note : The values are reference values.
• The relationship between external impedance and minimum sampling time
(External impedance = 0 kΩ to 20 kΩ)
(External impedance = 0 kΩ to 100 kΩ)
AVCC ≥ 2.7 V
AVCC ≥ 1.8 V
0
5
10
15
20
25
30
35
Minimum sampling time [µs]
40
External impedance [kΩ]
External impedance [kΩ]
AVCC ≥ 2.7 V
100
90
80
70
60
50
40
30
20
10
0
20
18
16
14
12
10
8
6
4
2
0
0
1
2
3
4
Minimum sampling time [µs]
• About errors
As |AVR − AVSS| becomes smaller, values of relative errors grow larger.
59
MB95120 Series
(3) Definition of A/D Converter Terms
• Resolution
The level of analog variation that can be distinguished by the A/D converter.
When the number of bits is 10, analog voltage can be divided into 210 = 1024.
• Linearity error (unit : LSB)
The deviation between the value along a straight line connecting the zero transition point
(“00 0000 0000” ← → “00 0000 0001”) of a device and the full-scale transition point
(“11 1111 1111” ← → “11 1111 1110”) compared with the actual conversion values obtained.
• Differential linear error (Unit : LSB)
Deviation of input voltage, which is required for changing output code by 1 LSB, from an ideal value.
• Total error (unit: LSB)
Difference between actual and theoretical values, caused by a zero transition error, full-scale transition error,
linearity error, quantum error, and noise.
Ideal I/O characteristics
Total error
VFST
3FFH
3FFH
3FEH
1.5 LSB
3FDH
004H
003H
002H
VOT
Digital output
Digital output
3FEH
3FDH
Actual conversion
characteristic
{1 LSB × (N − 1) + 0.5 LSB}
004H
003H
002H
1 LSB
VNT
Actual conversion
characteristic
Ideal characteristics
001H
001H
0.5 LSB
AVSS
AVR
Analog input
1 LSB =
AVR − AVSS
1024
(V)
AVSS
AVR
Analog input
Total error of VNT − {1 LSB × (N − 1) + 0.5 LSB}
=
[LSB]
digital output N
1 LSB
N : A/D converter digital output value
VNT : A voltage at which digital output transits from (N - 1) to N.
(Continued)
60
MB95120 Series
(Continued)
Full-scale transition error
Zero transition error
Ideal
characteristics
004H
3FFH
Digital output
Digital output
Actual conversion
characteristic
003H
Ideal
characteristics
002H
Actual conversion
characteristic
Actual conversion
characteristic
3FEH
VFST
(measurement
value)
3FDH
001H
VOT (measurement value)
AVSS
Actual conversion
characteristic
3FCH
AVR
AVSS
AVR
Analog input
Analog input
Differential linear error
Linearity error
Actual conversion
characteristic
3FFH
N+1H
3FEH
Actual conversion
characteristic
VFST
(measurement
value)
VNT
004H
Actual conversion
characteristic
003H
002H
Digital output
{1 LSB × N + VOT}
3FDH
Digital output
Ideal characteristics
NH
N-1H
VNT
Actual conversion
characteristic
Ideal characteristics
N-2H
001H
V (N+1)T
VOT (measurement value)
AVSS
AVR
AVSS
Analog input
Linear error in = VNT − {1 LSB × N + VOT}
1 LSB
digital output N
Analog input
Differential linear error =
in digital output N
V (N + 1) T − VNT
1 LSB
AVR
−1
N : A/D Converter digital output value
VNT : A voltage at which digital output transits from (N − 1) to N.
VOT (Ideal value) = AVSS + 0.5 LSB [V]
VFST (Ideal value) = AVR − 1.5 LSB [V]
61
MB95120 Series
6. Flash Memory Program/Erase Characteristics
Parameter
Value
Unit
Remarks
3.0*2
s
Excludes 00H programming prior erasure.
0.5*1
12.0*2
s
Excludes 00H programming prior erasure.
⎯
32
3600
µs
Excludes system-level overhead.
10000
⎯
⎯
cycle
Power supply voltage at
program/erase
2.7
⎯
3.3
V
Flash memory data retention
time
20*3
⎯
⎯
year
Min
Typ
Max
Sector erase time
(4 Kbytes sector)
⎯
0.2*1
Sector erase time
(16 Kbytes sector)
⎯
Byte programming time
Program/erase cycle
Average TA = +85 °C
*1 : TA = + 25 °C, VCC = 3.0 V, 10000 cycles
*2 : TA = + 85 °C, VCC = 2.7 V, 10000 cycles
*3 : This value comes from the technology qualification (using Arrhenius equation to translate high temperature
measurements into normalized value at +85 °C) .
62
MB95120 Series
■ MASK OPTION
Part number
No.
Specifying procedure
MB95F128D
MB95F128E
Setting disabled
MB95FV100D-101
MB95FV100D-102
Setting disabled
Setting disabled
1
Clock mode select
• Single-system clock mode
• Dual-system clock mode
Dual-system clock mode
2
LCDC Booster circuit select
• Internal division resistance
• Booster circuit
internal
division
resistance
3
Low voltage detection reset*
• With low voltage detection reset
• Without low voltage detection reset
No
No
4
Clock supervisor*
• With clock supervisor
• Without clock supervisor
No
No
5
Oscillation stabilization
wait time
Booster
circuit
Fixed to oscillation
stabilization wait time of
(214−2) /FCH
Changing by the switch on
MCU board
internal
division
resistance
Booster
circuit
Fixed to oscillation stabilization wait
time of (214−2) /FCH
* : Low voltage detection reset and clock supervisor are options of 5-V products.
63
MB95120 Series
■ ORDERING INFORMATION
Part number
MB95F128DPMC
MB95F128EPMC
100-pin plastic LQFP
(FPT-100P-M20)
MB95F128DPF
MB95F128EPF
100-pin plastic QFP
(FPT-100P-M06)
MB2146-301A
(MB95FV100D-101PBT)
MB2146-302A
(MB95FV100D-102PBT)
64
Package
(
MCU board
224-pin plastic PFBGA
(BGA-224P-M08)
Remarks
)
Included LCDC internal
division resistance
Included LCDC booster
MB95120 Series
■ PACKAGE DIMENSIONS
100-pin plastic LQFP
Lead pitch
0.50 mm
Package width ×
package length
14.0 mm × 14.0 mm
Lead shape
Gullwing
Sealing method
Plastic mold
Mounting height
1.70 mm Max
Weight
0.65 g
Code
(Reference)
P-LFQFP100-14×14-0.50
(FPT-100P-M20)
100-pin plastic LQFP
(FPT-100P-M20)
Note 1) * : These dimensions do not include resin protrusion.
Note 2) Pins width and pins thickness include plating thickness.
Note 3) Pins width do not include tie bar cutting remainder.
16.00±0.20(.630±.008)SQ
* 14.00±0.10(.551±.004)SQ
75
51
76
50
0.08(.003)
Details of "A" part
+0.20
26
100
1
C
0.08(.003)
(0.50(.020))
0.25(.010)
0.60±0.15
(.024±.006)
25
0.20±0.05
(.008±.002)
0.10±0.10
(.004±.004)
(Stand off)
0˚~8˚
"A"
0.50(.020)
+.008
1.50 –0.10 .059 –.004
(Mounting height)
INDEX
M
0.145±0.055
(.0057±.0022)
2005 FUJITSU LIMITED F100031S-c-2-1
Dimensions in mm (inches).
Note: The values in parentheses are reference values
Please confirm the latest Package dimension by following URL.
http://edevice.fujitsu.com/fj/DATASHEET/ef-ovpklv.html
(Continued)
65
MB95120 Series
(Continued)
100-pin plastic QFP
Lead pitch
0.65 mm
Package width ×
package length
14.00 × 20.00 mm
Lead shape
Gullwing
Sealing method
Plastic mold
Mounting height
3.35 mm MAX
Code
(Reference)
P-QFP100-14×20-0.65
(FPT-100P-M06)
100-pin plastic QFP
(FPT-100P-M06)
Note 1) * : These dimensions do not include resin protrusion.
Note 2) Pins width and pins thickness include plating thickness.
Note 3) Pins width do not include tie bar cutting remainder.
23.90±0.40(.941±.016)
* 20.00±0.20(.787±.008)
80
51
81
50
0.10(.004)
17.90±0.40
(.705±.016)
*14.00±0.20
(.551±.008)
INDEX
Details of "A" part
100
1
30
0.65(.026)
0.32±0.05
(.013±.002)
0.13(.005)
M
"A"
C
2002 FUJITSU LIMITED F100008S-c-5-5
Please confirm the latest Package dimension by following URL.
http://edevice.fujitsu.com/fj/DATASHEET/ef-ovpklv.html
66
0.25(.010)
+0.35
3.00 –0.20
+.014
.118 –.008
(Mounting height)
0~8˚
31
0.17±0.06
(.007±.002)
0.80±0.20
(.031±.008)
0.88±0.15
(.035±.006)
0.25±0.20
(.010±.008)
(Stand off)
Dimensions in mm (inches).
Note: The values in parentheses are reference values.
MB95120 Series
The information for microcontroller supports is shown in the following homepage.
http://www.fujitsu.com/global/services/microelectronics/product/micom/support/index.html
FUJITSU LIMITED
All Rights Reserved.
The contents of this document are subject to change without notice.
Customers are advised to consult with FUJITSU sales
representatives before ordering.
The information, such as descriptions of function and application
circuit examples, in this document are presented solely for the
purpose of reference to show examples of operations and uses of
Fujitsu semiconductor device; Fujitsu does not warrant proper
operation of the device with respect to use based on such
information. When you develop equipment incorporating the
device based on such information, you must assume any
responsibility arising out of such use of the information. Fujitsu
assumes no liability for any damages whatsoever arising out of
the use of the information.
Any information in this document, including descriptions of
function and schematic diagrams, shall not be construed as license
of the use or exercise of any intellectual property right, such as
patent right or copyright, or any other right of Fujitsu or any third
party or does Fujitsu warrant non-infringement of any third-party’s
intellectual property right or other right by using such information.
Fujitsu assumes no liability for any infringement of the intellectual
property rights or other rights of third parties which would result
from the use of information contained herein.
The products described in this document are designed, developed
and manufactured as contemplated for general use, including
without limitation, ordinary industrial use, general office use,
personal use, and household use, but are not designed, developed
and manufactured as contemplated (1) for use accompanying fatal
risks or dangers that, unless extremely high safety is secured, could
have a serious effect to the public, and could lead directly to death,
personal injury, severe physical damage or other loss (i.e., nuclear
reaction control in nuclear facility, aircraft flight control, air traffic
control, mass transport control, medical life support system, missile
launch control in weapon system), or (2) for use requiring
extremely high reliability (i.e., submersible repeater and artificial
satellite).
Please note that Fujitsu will not be liable against you and/or any
third party for any claims or damages arising in connection with
above-mentioned uses of the products.
Any semiconductor devices have an inherent chance of failure. You
must protect against injury, damage or loss from such failures by
incorporating safety design measures into your facility and
equipment such as redundancy, fire protection, and prevention of
over-current levels and other abnormal operating conditions.
If any products described in this document represent goods or
technologies subject to certain restrictions on export under the
Foreign Exchange and Foreign Trade Law of Japan, the prior
authorization by Japanese government will be required for export
of those products from Japan.
The company names and brand names herein are the trademarks or
registered trademarks of their respective owners.
Edited
Business Promotion Dept.
F0701