LATTICE LA4064ZV

LA-ispMACH 4000V/Z
Automotive Family
3.3V/1.8V In-System Programmable
SuperFAST TM High Density PLDs
July 2008
Data Sheet DS1017
Features
• 5V tolerant I/O for LVCMOS 3.3, LVTTL, and PCI
interfaces
• Hot-socketing
• Open-drain capability
• Input pull-up, pull-down or bus-keeper
• Programmable output slew rate
• 3.3V PCI compatible
• IEEE 1149.1 boundary scan testable
• 3.3V/2.5V/1.8V In-System Programmable
(ISP™) using IEEE 1532 compliant interface
• I/O pins with fast setup path
• Lead-free (RoHS) package
■ High Performance
• fMAX = 168MHz maximum operating frequency
• tPD = 7.5ns propagation delay
• Up to four global clock pins with programmable
clock polarity control
• Up to 80 PTs per output
■ Ease of Design
• Enhanced macrocells with individual clock,
reset, preset and clock enable controls
• Up to four global OE controls
• Individual local OE control per I/O pin
• Excellent First-Time-FitTM and refit
• Fast path, SpeedLockingTM Path, and wide-PT
path
• Wide input gating (36 input logic blocks) for fast
counters, state machines and address decoders
Introduction
The high performance LA-ispMACH 4000V/Z automotive family from Lattice offers a SuperFAST CPLD solution that is tested and qualified to the AEC-Q100
standard. The family is a blend of Lattice’s two most
popular architectures: the ispLSI® 2000 and ispMACH
4A. Retaining the best of both families, the LA-ispMACH
4000V/Z architecture focuses on significant innovations
to combine the highest performance with low power in a
flexible CPLD family.
■ Zero Power (LA-ispMACH 4000Z)
• Typical static current 10µA (4032Z)
• 1.8V core low dynamic power
• LA-ispMACH 4000Z operational down to 1.6V
■ AEC-Q100 Tested and Qualified
The LA-ispMACH 4000V/Z automotive family combines
high speed and low power with the flexibility needed for
ease of design. With its robust Global Routing Pool and
Output Routing Pool, this family delivers excellent FirstTime-Fit, timing predictability, routing, pin-out retention
and density migration.
• Automotive: -40 to 125°C ambient (TA)
■ Easy System Integration
• Superior solution for power sensitive consumer
applications
• Operation with 3.3V, 2.5V or 1.8V LVCMOS I/O
• Operation with 3.3V (4000V) or 1.8V (4000Z)
supplies
Table 1. LA-ispMACH 4000V Automotive Family Selection Guide
Macrocells
I/O + Dedicated Inputs
tPD (ns)
LA-ispMACH 4032V
LA-ispMACH 4064V
LA-ispMACH 4128V
32
64
128
30+2/32+4
30+2/32+4/64+10
64+10/92+4/96+4
7.5
7.5
7.5
tS (ns)
4.5
4.5
4.5
tCO (ns)
4.5
4.5
4.5
fMAX (MHz)
168
168
168
Supply Voltage (V)
3.3V
3.3V
3.3V
44-pin Lead-Free TQFP
48-pin Lead-Free TQFP
44-pin Lead-Free TQFP
48-pin Lead-Free TQFP
100-pin Lead-Free TQFP
Pins/Package
100-pin Lead-Free TQFP
128-pin Lead-Free TQFP
144-pin Lead-Free TQFP
© 2008 Lattice Semiconductor Corp. All Lattice trademarks, registered trademarks, patents, and disclaimers are as listed at www.latticesemi.com/legal. All other brand
or product names are trademarks or registered trademarks of their respective holders. The specifications and information herein are subject to change without notice.
www.latticesemi.com
1
DS1017_02.3
Lattice Semiconductor
LA-ispMACH 4000V/Z Automotive Family Data Sheet
Table 2. LA-ispMACH 4000Z Automotive Family Selection Guide
LA-ispMACH 4032Z
LA-ispMACH 4064Z
LA-ispMACH 4128Z
32
64
128
32+4
32+4/64+10
64+10
7.5
7.5
7.5
Macrocells
I/O + Dedicated Inputs
tPD (ns)
tS (ns)
4.5
4.5
4.5
tCO (ns)
4.5
4.5
4.5
fMAX (MHz)
168
168
168
Supply Voltage (V)
1.8V
1.8V
1.8V
48-pin Lead-Free TQFP
48-pin Lead-Free TQFP
100-pin Lead-Free TQFP
100-pin Lead-Free TQFP
Pins/Package
The LA-ispMACH 4000V/Z automotive family offers densities ranging from 32 to 128 macrocells. There are multiple
density-I/O combinations in Thin Quad Flat Pack (TQFP) packages ranging from 44 to 144 pins. Tables 1 and 2
show the macrocell, package and I/O options, along with other key parameters.
The LA-ispMACH 4000V/Z automotive family has enhanced system integration capabilities. It supports 3.3V (4000V
and 1.8V (4000Z) supply voltages and 3.3V, 2.5V and 1.8V interface voltages. Additionally, inputs can be safely
driven up to 5.5V when an I/O bank is configured for 3.3V operation, making this family 5V tolerant. The LAispMACH 4000V/Z also offers enhanced I/O features such as slew rate control, PCI compatibility, bus-keeper
latches, pull-up resistors, pull-down resistors, open drain outputs and hot socketing. The LA-ispMACH 4000V/Z
automotive family is in-system programmable through the IEEE Standard 1532 interface. IEEE Standard 1149.1
boundary scan testing capability also allows product testing on automated test equipment. The 1532 interface signals TCK, TMS, TDI and TDO are referenced to VCC (logic core).
Overview
The LA-ispMACH 4000V/Z automotive devices consist of multiple 36-input, 16-macrocell Generic Logic Blocks
(GLBs) interconnected by a Global Routing Pool (GRP). Output Routing Pools (ORPs) connect the GLBs to the I/O
Blocks (IOBs), which contain multiple I/O cells. This architecture is shown in Figure 1.
16
16
Generic
Logic
Block
I/O
Block
ORP
36
36
16
16
36
36
2
Generic
16
Logic
Block
VCCO1
GND
TCK
TMS
TDI
TDO
VCC
GND
GOE0
GOE1
16
16
I/O Bank 0
ORP
Generic
Logic
Block
I/O
Block
ORP
I/O Bank 1
I/O
Block
Global Routing Pool
VCCO0
GND
CLK0/I
CLK1/I
CLK2/I
CLK3/I
Figure 1. Functional Block Diagram
Generic
16
Logic
Block
I/O
Block
ORP
Lattice Semiconductor
LA-ispMACH 4000V/Z Automotive Family Data Sheet
The I/Os in the LA-ispMACH 4000V/Z automotive devices are split into two banks. Each bank has a separate I/O
power supply. Inputs can support a variety of standards independent of the chip or bank power supply. Outputs
support the standards compatible with the power supply provided to the bank. Support for a variety of standards
helps designers implement designs in mixed voltage environments. In addition, 5V tolerant inputs are specified
within an I/O bank that is connected to VCCO of 3.0V to 3.6V for LVCMOS 3.3, LVTTL and PCI interfaces.
LA-ispMACH 4000V/Z Automotive Architecture
There are a total of two GLBs in the LA-ispMACH 4032V/Z, increasing to 8 GLBs in the LA-ispMACH 4128V/Z.
Each GLB has 36 inputs. All GLB inputs come from the GRP and all outputs from the GLB are brought back into
the GRP to be connected to the inputs of any other GLB on the device. Even if feedback signals return to the same
GLB, they still must go through the GRP. This mechanism ensures that GLBs communicate with each other with
consistent and predictable delays. The outputs from the GLB are also sent to the ORP. The ORP then sends them
to the associated I/O cells in the I/O block.
Generic Logic Block
The LA-ispMACH 4000V/Z Automotive GLB consists of a programmable AND array, logic allocator, 16 macrocells
and a GLB clock generator. Macrocells are decoupled from the product terms through the logic allocator and the I/O
pins are decoupled from macrocells through the ORP. Figure 2 illustrates the GLB.
To GRP
CLK3
CLK2
CLK1
CLK0
Figure 2. Generic Logic Block
Clock
Generator
1+OE
1+OE
1+OE
1+OE
To ORP
16 MC Feedback Signals
16 Macrocells
Logic Allocator
36 Inputs
from GRP
AND Array
36 Inputs,
83 Product Terms
1+OE
1+OE
1+OE
1+OE
To
Product Term
Output Enable
Sharing
AND Array
The programmable AND Array consists of 36 inputs and 83 output product terms. The 36 inputs from the GRP are
used to form 72 lines in the AND Array (true and complement of the inputs). Each line in the array can be connected to any of the 83 output product terms via a wired-AND. Each of the 80 logic product terms feed the logic
allocator with the remaining three control product terms feeding the Shared PT Clock, Shared PT Initialization and
Shared PT OE. The Shared PT Clock and Shared PT Initialization signals can optionally be inverted before being
fed to the macrocells.
Every set of five product terms from the 80 logic product terms forms a product term cluster starting with PT0.
There is one product term cluster for every macrocell in the GLB. Figure 3 is a graphical representation of the AND
Array.
3
Lattice Semiconductor
LA-ispMACH 4000V/Z Automotive Family Data Sheet
Figure 3. AND Array
In[0]
In[34]
In[35]
PT0
PT1
PT2
PT3
PT4
Cluster 0
PT75
PT76
PT77
Cluster 15
PT78
PT79
PT80 Shared PT Clock
PT81 Shared PT Initialization
PT82 Shared PTOE
Note:
Indicates programmable fuse.
Enhanced Logic Allocator
Within the logic allocator, product terms are allocated to macrocells in product term clusters. Each product term
cluster is associated with a macrocell. The cluster size for the LA-ispMACH 4000V/Z automotive family is 4+1 (total
5) product terms. The software automatically considers the availability and distribution of product term clusters as it
fits the functions within a GLB. The logic allocator is designed to provide three speed paths: 5-PT fast bypass path,
20-PT Speed Locking path and an up to 80-PT path. The availability of these three paths lets designers trade timing variability for increased performance.
The enhanced Logic Allocator of the LA-ispMACH 4000V/Z automotive family consists of the following blocks:
• Product Term Allocator
• Cluster Allocator
• Wide Steering Logic
Figure 4 shows a macrocell slice of the Logic Allocator. There are 16 such slices in the GLB.
Figure 4. Macrocell Slice
to to
n-1 n-2
from from
n-1 n-4
From
n-4
Fast 5-PT
Path
1-80
PTs
5-PT
n
To XOR (MC)
Cluster
to
n+1
Individual Product
Term Allocator
from
n+2
Cluster
Allocator
4
from
n+1
To n+4
SuperWIDE™
Steering Logic
Lattice Semiconductor
LA-ispMACH 4000V/Z Automotive Family Data Sheet
Product Term Allocator
The product term allocator assigns product terms from a cluster to either logic or control applications as required
by the design being implemented. Product terms that are used as logic are steered into a 5-input OR gate associated with the cluster. Product terms that used for control are steered either to the macrocell or I/O cell associated
with the cluster. Table 3 shows the available functions for each of the five product terms in the cluster. The OR gate
output connects to the associated I/O cell, providing a fast path for narrow combinatorial functions, and to the logic
allocator.
Table 3. Individual PT Steering
Product Term
Logic
PTn
Logic PT
Single PT for XOR/OR
Control
PTn+1
Logic PT
Individual Clock (PT Clock)
PTn+2
Logic PT
Individual Initialization or Individual Clock Enable (PT Initialization/CE)
PTn+3
Logic PT
Individual Initialization (PT Initialization)
PTn+4
Logic PT
Individual OE (PTOE)
Cluster Allocator
The cluster allocator allows clusters to be steered to neighboring macrocells, thus allowing the creation of functions
with more product terms. Table 4 shows which clusters can be steered to which macrocells. Used in this manner,
the cluster allocator can be used to form functions of up to 20 product terms. Additionally, the cluster allocator
accepts inputs from the wide steering logic. Using these inputs, functions up to 80 product terms can be created.
Table 4. Available Clusters for Each Macrocell
Macrocell
Available Clusters
M0
—
C0
C1
C2
M1
C0
C1
C2
C3
M2
C1
C2
C3
C4
M3
C2
C3
C4
C5
M4
C3
C4
C5
C6
M5
C4
C5
C6
C7
M6
C5
C6
C7
C8
M7
C6
C7
C8
C9
M8
C7
C8
C9
C10
M9
C8
C9
C10
C11
M10
C9
C10
C11
C12
M11
C10
C11
C12
C13
M12
C11
C12
C13
C14
M13
C12
C13
C14
C15
M14
C13
C14
C15
—
M15
C14
C15
—
—
Wide Steering Logic
The wide steering logic allows the output of the cluster allocator n to be connected to the input of the cluster allocator n+4. Thus, cluster chains can be formed with up to 80 product terms, supporting wide product term functions
and allowing performance to be increased through a single GLB implementation. Table 5 shows the product term
chains.
5
Lattice Semiconductor
LA-ispMACH 4000V/Z Automotive Family Data Sheet
Table 5. Product Term Expansion Capability
Expansion Chains
Macrocells Associated with Expansion Chain (with Wrap Around)
Max PT/Macrocell
Chain-0
M0 → M4 → M8 → M12 → M0
75
Chain-1
M1 → M5 → M9 → M13 → M1
80
Chain-2
M2 → M6 → M10 → M14 → M2
75
Chain-3
M3 → M7 → M11 → M15 → M3
70
Every time the super cluster allocator is used, there is an incremental delay of tEXP . When the super cluster allocator is used, all destinations other than the one being steered to, are given the value of ground (i.e., if the super cluster is steered to M (n+4), then M (n) is ground).
Macrocell
The 16 macrocells in the GLB are driven by the 16 outputs from the logic allocator. Each macrocell contains a programmable XOR gate, a programmable register/latch, along with routing for the logic and control functions.
Figure 5 shows a graphical representation of the macrocell. The macrocells feed the ORP and GRP. A direct input
from the I/O cell allows designers to use the macrocell to construct high-speed input registers. A programmable
delay in this path allows designers to choose between the fastest possible set-up time and zero hold time.
Figure 5. Macrocell
Power-up
Initialization
Shared PT Initialization
PT Initialization (optional)
PT Initialization/CE (optional)
Delay
From I/O Cell
R
From Logic Allocator
D/T/L
P
To ORP
Q
To GRP
CE
Single PT
Block CLK0
Block CLK1
Block CLK2
Block CLK3
PT Clock (optional)
Shared PT Clock
Enhanced Clock Multiplexer
The clock input to the flip-flop can select any of the four block clocks along with the shared PT clock, and true and
complement forms of the optional individual term clock. An 8:1 multiplexer structure is used to select the clock. The
eight sources for the clock multiplexer are as follows:
• Block CLK0
• Block CLK1
• Block CLK2
6
Lattice Semiconductor
•
•
•
•
•
LA-ispMACH 4000V/Z Automotive Family Data Sheet
Block CLK3
PT Clock
PT Clock Inverted
Shared PT Clock
Ground
Clock Enable Multiplexer
Each macrocell has a 4:1 clock enable multiplexer. This allows the clock enable signal to be selected from the following four sources:
• PT Initialization/CE
• PT Initialization/CE Inverted
• Shared PT Clock
• Logic High
Initialization Control
The LA-ispMACH 4000V/Z automotive family architecture accommodates both block-level and macrocell-level set
and reset capability. There is one block-level initialization term that is distributed to all macrocell registers in a GLB.
At the macrocell level, two product terms can be “stolen” from the cluster associated with a macrocell to be used for
set/reset functionality. A reset/preset swapping feature in each macrocell allows for reset and preset to be
exchanged, providing flexibility.
Note that the reset/preset swapping selection feature affects power-up reset as well. All flip-flops power up to a
known state for predictable system initialization. If a macrocell is configured to SET on a signal from the block-level
initialization, then that macrocell will be SET during device power-up. If a macrocell is configured to RESET on a
signal from the block-level initialization or is not configured for set/reset, then that macrocell will RESET on powerup. To guarantee initialization values, the VCC rise must be monotonic, and the clock must be inactive until the reset
delay time has elapsed.
GLB Clock Generator
Each LA-ispMACH 4000V/Z automotive device has up to four clock pins that are also routed to the GRP to be used
as inputs. These pins drive a clock generator in each GLB, as shown in Figure 6. The clock generator provides four
clock signals that can be used anywhere in the GLB. These four GLB clock signals can consist of a number of combinations of the true and complement edges of the global clock signals.
Figure 6. GLB Clock Generator
CLK0
Block CLK0
CLK1
Block CLK1
CLK2
Block CLK2
CLK3
Block CLK3
7
Lattice Semiconductor
LA-ispMACH 4000V/Z Automotive Family Data Sheet
Output Routing Pool (ORP)
The Output Routing Pool allows macrocell outputs to be connected to any of several I/O cells within an I/O block.
This provides greater flexibility in determining the pinout and allows design changes to occur without affecting the
pinout. The output routing pool also provides a parallel capability for routing macrocell-level OE product terms. This
allows the OE product term to follow the macrocell output as it is switched between I/O cells. Additionally, the output routing pool allows the macrocell output or true and complement forms of the 5-PT bypass signal to bypass the
output routing multiplexers and feed the I/O cell directly. The enhanced ORP of the LA-ispMACH 4000V/Z family
consists of the following elements:
• Output Routing Multiplexers
• OE Routing Multiplexers
• Output Routing Pool Bypass Multiplexers
Figure 7 shows the structure of the ORP from the I/O cell perspective. This is referred to as an ORP slice. Each
ORP has as many ORP slices as there are I/O cells in the corresponding I/O block.
Figure 7. ORP Slice
OE Routing Multiplexer
From PTOE
To I/O
Cell
OE
ORP
Bypass
Multiplexer
5-PT Fast Path
To I/O
Cell
From Macrocell
Output
Output Routing Multiplexer
Output Routing Multiplexers
The details of connections between the macrocells and the I/O cells vary across devices and within a device
dependent on the maximum number of I/Os available. Tables 6-10 provide the connection details.
Table 6. ORP Combinations for I/O Blocks with 8 I/Os
I/O Cell
Available Macrocells
I/O 0
M0, M1, M2, M3, M4, M5, M6, M7
I/O 1
M2, M3, M4, M5, M6, M7, M8, M9
I/O 2
M4, M5, M6, M7, M8, M9, M10, M11
I/O 3
M6, M7, M8, M9, M10, M11, M12, M13
I/O 4
M8, M9, M10, M11, M12, M13, M14, M15
I/O 5
M10, M11, M12, M13, M14, M15, M0, M1
I/O 6
M12, M13, M14, M15, M0, M1, M2, M3
I/O 7
M14, M15, M0, M1, M2, M3, M4, M5
8
Lattice Semiconductor
LA-ispMACH 4000V/Z Automotive Family Data Sheet
Table 7. ORP Combinations for I/O Blocks with 16 I/Os
I/O Cell
Available Macrocells
I/O 0
M0, M1, M2, M3, M4, M5, M6, M7
I/O 1
M1, M2, M3, M4, M5, M6, M7, M8
I/O 2
M2, M3, M4, M5, M6, M7, M8, M9
I/O 3
M3, M4, M5, M6, M7, M8, M9, M10
I/O 4
M4, M5, M6, M7, M8, M9, M10, M11
I/O 5
M5, M6, M7, M8, M9, M10, M11, M12
I/O 6
M6, M7, M8, M9, M10, M11, M12, M13
I/O 7
M7, M8, M9, M10, M11, M12, M13, M14
I/O 8
M8, M9, M10, M11, M12, M13, M14, M15
I/O 9
M9, M10, M11, M12, M13, M14, M15, M0
I/O 10
M10, M11, M12, M13, M14, M15, M0, M1
I/O 11
M11, M12, M13, M14, M15, M0, M1, M2
I/O 12
M12, M13, M14, M15, M0, M1, M2, M3
I/O 13
M13, M14, M15, M0, M1, M2, M3, M4
I/O 14
M14, M15, M0, M1, M2, M3, M4, M5
I/O 15
M15, M0, M1, M2, M3, M4, M5, M6
Table 8. ORP Combinations for I/O Blocks with 12 I/Os
I/O Cell
Available Macrocells
I/O 0
M0, M1, M2, M3, M4, M5, M6, M7
I/O 1
M1, M2, M3, M4, M5, M6, M7, M8
I/O 2
M2, M3, M4, M5, M6, M7, M8, M9
I/O 3
M4, M5, M6, M7, M8, M9, M10, M11
I/O 4
M5, M6, M7, M8, M9, M10, M11, M12
I/O 5
M6, M7, M8, M9, M10, M11, M12, M13
I/O 6
M8, M9, M10, M11, M12, M13, M14, M15
I/O 7
M9, M10, M11, M12, M13, M14, M15, M0
I/O 8
M10, M11, M12, M13, M14, M15, M0, M1
I/O 9
M12, M13, M14, M15, M0, M1, M2, M3
I/O 10
M13, M14, M15, M0, M1, M2, M3, M4
I/O 11
M14, M15, M0, M1, M2, M3, M4, M5
ORP Bypass and Fast Output Multiplexers
The ORP bypass and fast-path output multiplexer is a 4:1 multiplexer and allows the 5-PT fast path to bypass the
ORP and be connected directly to the pin with either the regular output or the inverted output. This multiplexer also
allows the register output to bypass the ORP to achieve faster tCO.
Output Enable Routing Multiplexers
The OE Routing Pool provides the corresponding local output enable (OE) product term to the I/O cell.
I/O Cell
The I/O cell contains the following programmable elements: output buffer, input buffer, OE multiplexer and bus
maintenance circuitry. Figure 8 details the I/O cell.
9
Lattice Semiconductor
LA-ispMACH 4000V/Z Automotive Family Data Sheet
Figure 8. I/O Cell
GOE 0
GOE 1
GOE 2
GOE 3
From ORP
VCC
VCCO
VCCO
*
From ORP
*
*
To Macrocell
To GRP
*Global fuses
Each output supports a variety of output standards dependent on the VCCO supplied to its I/O bank. Outputs can
also be configured for open drain operation. Each input can be programmed to support a variety of standards, independent of the VCCO supplied to its I/O bank. The I/O standards supported are:
• LVTTL
• LVCMOS 1.8
• LVCMOS 3.3
• 3.3V PCI Compatible
• LVCMOS 2.5
All of the I/Os and dedicated inputs have the capability to provide a bus-keeper latch, Pull-up Resistor or Pull-down
Resistor. A fourth option is to provide none of these. The selection is done on a global basis. The default in both
hardware and software is such that when the device is erased or if the user does not specify, the input structure is
configured to be a Pull-up Resistor.
Each LA-ispMACH 4000V/Z automotive device I/O has an individually programmable output slew rate control bit.
Each output can be individually configured for fast slew or slow slew. The typical edge rate difference between fast
and slow slew setting is 20%. For high-speed designs with long, unterminated traces, the slow-slew rate will introduce fewer reflections, less noise and keep ground bounce to a minimum. For designs with short traces or well terminated lines, the fast slew rate can be used to achieve the highest speed.
Global OE Generation
Most LA-ispMACH 4000V/Z automotive family devices have a 4-bit wide Global OE Bus, except the LA-ispMACH
4032V and LA-ispMACH4032Z devices that have a 2-bit wide Global OE Bus. This bus is derived from a 4-bit internal global OE PT bus and two dual purpose I/O or GOE pins. Each signal that drives the bus can optionally be
inverted.
Each GLB has a block-level OE PT that connects to all bits of the Global OE PT bus with four fuses. Hence, for a
128-macrocell device (with 16 blocks), each line of the bus is driven from 8 OE product terms. Figures 9 and 10
show a graphical representation of the global OE generation.
10
Lattice Semiconductor
LA-ispMACH 4000V/Z Automotive Family Data Sheet
Figure 9. Global OE Generation for All Devices Except LA-ispMACH 4032V/Z
Internal Global OE
PT Bus
(4 lines)
Global OE
4-Bit
Global OE Bus
Shared PTOE
(Block 0)
Shared PTOE
(Block n)
Global
Fuses
GOE (0:3)
to I/O cells
Fuse connection
Hard wired
Figure 10. Global OE Generation for LA-ispMACH 4032V/Z
Internal Global OE
PT Bus
(2 lines)
Global OE
4-Bit
Global OE Bus
Shared PTOE
(Block 0)
Shared PTOE
(Block 1)
Global
Fuses
GOE (3:0)
to I/O cells
Fuse connection
Hard wired
Zero Power/Low Power and Power Management
The LA-ispMACH 4000V/Z automotive family is designed with high speed low power design techniques to offer
both high speed and low power. With an advanced E2 low power cell and non sense-amplifier design approach (full
CMOS logic approach), the LA-ispMACH 4000V/Z automotive family offers SuperFAST pin-to-pin speeds, while
simultaneously delivering low standby power without needing any “turbo bits” or other power management
schemes associated with a traditional sense-amplifier approach.
11
Lattice Semiconductor
LA-ispMACH 4000V/Z Automotive Family Data Sheet
The zero power LA-ispMACH 4000Z is based on the 1.8V ispMACH 4000C family. With innovative circuit design
changes, the LA-ispMACH 4000Z family is able to achieve the industry’s “lowest static power”.
IEEE 1149.1-Compliant Boundary Scan Testability
All LA-ispMACH 4000V/Z automotive devices have boundary scan cells and are compliant to the IEEE 1149.1
standard. This allows functional testing of the circuit board on which the device is mounted through a serial scan
path that can access all critical logic notes. Internal registers are linked internally, allowing test data to be shifted in
and loaded directly onto test nodes, or test node data to be captured and shifted out for verification. In addition,
these devices can be linked into a board-level serial scan path for more board-level testing. The test access port
operates with an LVCMOS interface that corresponds to the power supply voltage.
I/O Quick Configuration
To facilitate the most efficient board test, the physical nature of the I/O cells must be set before running any continuity tests. As these tests are fast, by nature, the overhead and time that is required for configuration of the I/Os’
physical nature should be minimal so that board test time is minimized. The LA-ispMACH 4000V/Z automotive family of devices allows this by offering the user the ability to quickly configure the physical nature of the I/O cells. This
quick configuration takes milliseconds to complete, whereas it takes seconds for the entire device to be programmed. Lattice's ispVM™ System programming software can either perform the quick configuration through the
PC parallel port, or can generate the ATE or test vectors necessary for a third-party test system.
IEEE 1532-Compliant In-System Programming
Programming devices in-system provides a number of significant benefits including: rapid prototyping, lower inventory levels, higher quality and the ability to make in-field modifications. The LA-ispMACH 4000V/Z automotive
devices provide In-System Programming (ISP™) capability through the Boundary Scan Test Access Port. This
capability has been implemented in a manner that ensures that the port remains complaint to the IEEE 1149.1
standard. By using IEEE 1149.1 as the communication interface through which ISP is achieved, users get the benefit of a standard, well-defined interface. All LA-ispMACH 4000V/Z automotive devices are also compliant with the
IEEE 1532 standard.
The LA-ispMACH 4000V/Z automotive devices can be programmed across the commercial temperature and voltage range. The PC-based Lattice software facilitates in-system programming of LA-ispMACH 4000V/Z automotive
devices. The software takes the JEDEC file output produced by the design implementation software, along with
information about the scan chain, and creates a set of vectors used to drive the scan chain. The software can use
these vectors to drive a scan chain via the parallel port of a PC. Alternatively, the software can output files in formats understood by common automated test equipment. This equipment can then be used to program LAispMACH 4000V/Z automotive devices during the testing of a circuit board.
User Electronic Signature
The User Electronic Signature (UES) allows the designer to include identification bits or serial numbers inside the
device, stored in E2CMOS memory. The LA-ispMACH 4000V/Z automotive device contains 32 UES bits that can be
configured by the user to store unique data such as ID codes, revision numbers or inventory control codes.
Security Bit
A programmable security bit is provided on the LA-ispMACH 4000V/Z automotive devices as a deterrent to unauthorized copying of the array configuration patterns. Once programmed, this bit defeats readback of the programmed pattern by a device programmer, securing proprietary designs from competitors. Programming and
verification are also defeated by the security bit. The bit can only be reset by erasing the entire device.
Hot Socketing
The LA-ispMACH 4000V/Z automotive devices are well-suited for applications that require hot socketing capability.
Hot socketing a device requires that the device, during power-up and down, can tolerate active signals on the I/Os
12
Lattice Semiconductor
LA-ispMACH 4000V/Z Automotive Family Data Sheet
and inputs without being damaged. Additionally, it requires that the effects of I/O pin loading be minimal on active
signals. The LA-ispMACH 4000V/Z automotive devices provide this capability for input voltages in the range 0V to
3.0V.
Density Migration
The LA-ispMACH 4000V/Z automotive family has been designed to ensure that different density devices in the
same package have the same pin-out. Furthermore, the architecture ensures a high success rate when performing
design migration from lower density parts to higher density parts. In many cases, it is possible to shift a lower utilization design targeted for a high density device to a lower density device. However, the exact details of the final
resource utilization will impact the likely success in each case.
AEC-Q100 Tested and Qualified
The Automotive Electronics Council (AEC) consists of two committees: the Quality Systems Committee and the
Component Technical Committee. These committees are composed of representatives from sustaining and other
associate members. The AEC Component Technical Committee is the standardization body for establishing standards for reliable, high quality electronic components. In particular, the AEC-Q100 specification “Stress Test for
Qualification for Integrated Circuits” defines qualification and re-qualification requirements for electronic components. Components meeting these specifications are suitable for use in the harsh automotive environment without
additional component-level qualification testing. Lattice's LA-ispMACH 4000V/Z and LA-MachXO devices completed and passed the requirements of the AEC-Q100 specification.
13
Lattice Semiconductor
LA-ispMACH 4000V/Z Automotive Family Data Sheet
Absolute Maximum Ratings1, 2, 3
LA-ispMACH 4000V (3.3V)
LA-ispMACH 4000Z (1.8V)
Supply Voltage (VCC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.5 to 5.5V . . . . . . . . . . . . . . . . -0.5 to 2.5V
Output Supply Voltage (VCCO) . . . . . . . . . . . . . . . . . . . . . . . -0.5 to 4.5V . . . . . . . . . . . . . . . . -0.5 to 4.5V
Input or I/O Tristate Voltage Applied4, 5 . . . . . . . . . . . . . . . . . -0.5 to 5.5V . . . . . . . . . . . . . . . . -0.5 to 5.5V
Storage Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -65 to 150°C . . . . . . . . . . . . . . . -65 to 150°C
Junction Temperature (Tj) with Power Applied . . . . . . . . . . -55 to 150°C . . . . . . . . . . . . . . . -55 to 150°C
1. Stress above those listed under the “Absolute Maximum Ratings” may cause permanent damage to the device. Functional
operation of the device at these or any other conditions above those indicated in the operational sections of this specification
is not implied.
2. Compliance with Lattice Thermal Management document is required.
3. All voltages referenced to GND.
4. Undershoot of -2V and overshoot of (VIH (MAX) + 2V), up to a total pin voltage of 6.0V, is permitted for a duration of < 20ns.
5. Maximum of 64 I/Os per device with VIN > 3.6V is allowed.
Recommended Operating Conditions
Symbol
VCC
TA
Parameter
Min.
Max.
Units
LA-ispMACH 4000V Supply Voltage
3.0
3.6
V
LA-ispMACH 4000Z Supply Voltage
1.7
1.9
V
LA-ispMACH 4000Z, Extended Functional Voltage Operations
1
1.6
1.9
V
Ambient Temperature (Automotive)
-40
125
C
Min.
Max.
Units
1,000
—
Cycles
1. Devices operating at 1.6V can expect performance degradation up to 35%.
Erase Reprogram Specifications
Parameter
Erase/Reprogram Cycle
Note: Valid over commercial temperature range.
Hot Socketing Characteristics1,2,3
Symbol
IDK
1.
2.
3.
Parameter
Input or I/O Leakage Current
Min.
Typ.
Max.
Units
0 ≤ VIN ≤ 3.0V, Tj = 105°C
Condition
—
±30
±150
µA
0 ≤ VIN ≤ 3.0V, Tj = 130°C
—
±30
±200
µA
Insensitive to sequence of VCC or VCCO. However, assumes monotonic rise/fall rates for VCC and VCCO, provided (VIN - VCCO) ≤ 3.6V.
0 < VCC < VCC (MAX), 0 < VCCO < VCCO (MAX).
IDK is additive to IPU, IPD or IBH. Device defaults to pull-up until fuse circuitry is active.
14
Lattice Semiconductor
LA-ispMACH 4000V/Z Automotive Family Data Sheet
I/O Recommended Operating Conditions
VCCO (V)1
Standard
LVTTL
Min.
Max.
3.0
3.6
LVCMOS 3.3
3.0
3.6
Extended LVCMOS 3.32
2.7
3.6
LVCMOS 2.5
2.3
2.7
LVCMOS 1.8
1.65
1.95
PCI 3.3
3.0
3.6
1. Typical values for VCCO are the average of the min. and max. values.
2. LA-ispMACH 4000Z only.
DC Electrical Characteristics
Over Recommended Operating Conditions
Symbol
IIL, IIH1, 4
IIH1, 2
IPU
Parameter
Min.
Typ.
Max.
Units
0 ≤ VIN < VCCO
—
0.5
1
µA
3.6V < VIN ≤ 5.5V, Tj = 105°C
3.0V ≤ VCCO ≤ 3.6V
—
—
20
µA
3.6V < VIN ≤ 5.5V, Tj = 130°C
3.0V ≤ VCCO ≤ 3.6V
—
—
50
µA
Input High Leakage Current
(LA-ispMACH 4000Z)
VCCO < VIN ≤ 5.5V
—
—
10
µA
I/O Weak Pull-up Resistor Current
(LA-ispMACH 4000V)
0 ≤ VIN ≤ 0.7VCCO
-30
—
-200
µA
I/O Weak Pull-up Resistor Current
(LA-ispMACH 4000Z)
0 ≤ VIN ≤ 0.7VCCO
-30
—
-150
µA
30
—
150
µA
Input Leakage Current
(LA-ispMACH 4000Z)
Input High Leakage Current
(LA-ispMACH 4000V)
Condition
IPD
I/O Weak Pull-down Resistor Current VIL (MAX) ≤ VIN ≤ VIH (MIN)
IBHLS
Bus Hold Low Sustaining Current
VIN = VIL (MAX)
30
—
—
µA
IBHHS
Bus Hold High Sustaining Current
VIN = 0.7 VCCO
-30
—
—
µA
IBHLO
Bus Hold Low Overdrive Current
0V ≤ VIN ≤ VBHT
—
—
150
µA
IBHHO
Bus Hold High Overdrive Current
VBHT ≤ VIN ≤ VCCO
—
—
-150
µA
VBHT
Bus Hold Trip Points
VCCO * 0.35
—
VCCO * 0.65
V
C1
I/O Capacitance3
C2
Clock Capacitance3
C3
Global Input Capacitance3
—
VCCO = 3.3V, 2.5V, 1.8V
—
VCC = 1.8V, VIO = 0 to VIH (MAX)
—
VCCO = 3.3V, 2.5V, 1.8V
—
VCC = 1.8V, VIO = 0 to VIH (MAX)
—
VCCO = 3.3V, 2.5V, 1.8V
—
VCC = 1.8V, VIO = 0 to VIH (MAX)
—
8
6
6
—
—
—
—
—
—
pf
pf
pf
1. Input or I/O leakage current is measured with the pin configured as an input or as an I/O with the output driver tristated. It is not
measured with the output driver active. Bus maintenance circuits are disabled.
2. 5V tolerant inputs and I/O should only be placed in banks where 3.0V ≤ VCCO ≤ 3.6V.
3. TA = 25°C, f = 1.0MHz.
4. IIH excursions of up to 1.5µA maximum per pin above the spec limit may be observed for certain voltage conditions on no more than 10% of
the device’s I/O pins.
15
Lattice Semiconductor
LA-ispMACH 4000V/Z Automotive Family Data Sheet
Supply Current, LA-ispMACH 4000V
Over Recommended Operating Conditions
Symbol
Parameter
Condition
Min.
Typ.
Max.
Units
LA-ispMACH 4032V
ICC
Operating Power Supply Current
Vcc = 3.3V
—
11.8
—
mA
Standby Power Supply Current
Vcc = 3.3V
—
11.3
—
mA
LA-ispMACH 4064V
ICC
Operating Power Supply Current
Vcc = 3.3V
—
12
—
mA
Standby Power Supply Current
Vcc = 3.3V
—
11.5
—
mA
Operating Power Supply Current
Vcc = 3.3V
—
12
—
mA
Standby Power Supply Current
Vcc = 3.3V
—
11.5
—
mA
LA-ispMACH 4128V
ICC
16
Lattice Semiconductor
LA-ispMACH 4000V/Z Automotive Family Data Sheet
Supply Current, LA-ispMACH 4000Z
Over Recommended Operating Conditions
Symbol
Parameter
Condition
Min.
Typ.
Max. Units
Vcc = 1.8V, TA = 25°C
—
50
—
µA
Vcc = 1.9V, TA = 70°C
—
58
—
µA
Vcc = 1.9V, TA = 85°C
—
60
—
µA
LA-ispMACH 4032Z
ICC1, 2, 3, 5
ICC4, 5
Operating Power Supply Current
Standby Power Supply Current
Vcc = 1.9V, TA = 125°C
—
70
—
µA
Vcc = 1.8V, TA = 25°C
—
10
—
µA
Vcc = 1.9V, TA = 70°C
—
13
20
µA
Vcc = 1.9V, TA = 85°C
—
15
25
µA
Vcc = 1.9V, TA = 125°C
—
22
µA
LA-ispMACH 4064Z
ICC1, 2, 3, 5
ICC4, 5
Operating Power Supply Current
Standby Power Supply Current
Vcc = 1.8V, TA = 25°C
—
80
—
µA
Vcc = 1.9V, TA = 70°C
—
89
—
µA
Vcc = 1.9V, TA = 85°C
—
92
—
µA
Vcc = 1.9V, TA = 125°C
—
109
—
µA
Vcc = 1.8V, TA = 25°C
—
11
—
µA
Vcc = 1.9V, TA = 70°C
—
15
25
µA
Vcc = 1.9V, TA = 85°C
—
18
35
Vcc = 1.9V, TA = 125°C
—
37
Vcc = 1.8V, TA = 25°C
—
168
—
µA
Vcc = 1.9V, TA = 70°C
—
190
—
µA
Vcc = 1.9V, TA = 85°C
—
195
—
µA
Vcc = 1.9V, TA = 125°C
—
212
—
µA
Vcc = 1.8V, TA = 25°C
—
12
—
µA
Vcc = 1.9V, TA = 70°C
—
16
35
µA
Vcc = 1.9V, TA = 85°C
—
19
50
µA
Vcc = 1.9V, TA = 125°C
—
42
—
µA
µA
µA
LA-ispMACH 4128Z
ICC1, 2, 3, 5
ICC4, 5
1.
2.
3.
4.
5.
Operating Power Supply Current
Standby Power Supply Current
TA = 25°C, frequency = 1.0 MHz.
Device configured with 16-bit counters.
ICC varies with specific device configuration and operating frequency.
VCCO = 3.6V, VIN = 0V or VCCO, bus maintenance turned off. VIN above VCCO will add transient current above the specified standby ICC.
Includes VCCO current without output loading.
17
Lattice Semiconductor
LA-ispMACH 4000V/Z Automotive Family Data Sheet
I/O DC Electrical Characteristics
Over Recommended Operating Conditions
VIH
VIL
Standard
LVTTL
LVCMOS 3.3
Min (V)
Max (V)
Min (V)
Max (V)
-0.3
0.80
2.0
5.5
-0.3
LVCMOS 2.5
0.80
-0.3
LVCMOS 1.8
(4000V)
2.0
0.70
-0.3
5.5
1.70
0.63
3.6
1.17
3.6
VOL
Max (V)
VOH
Min (V)
IOL1
(mA)
IOH1
(mA)
0.40
VCCO - 0.40
8.0
-4.0
0.20
VCCO - 0.20
0.1
-0.1
0.40
VCCO - 0.40
8.0
-4.0
0.20
VCCO - 0.20
0.1
-0.1
0.40
VCCO - 0.40
8.0
-4.0
0.20
VCCO - 0.20
0.1
-0.1
0.40
VCCO - 0.45
2.0
-2.0
0.20
VCCO - 0.20
0.1
-0.1
0.40
VCCO - 0.45
2.0
-2.0
LVCMOS 1.8
(4000Z)
-0.3
0.35 * VCC
0.65 * VCC
3.6
0.20
VCCO - 0.20
0.1
-0.1
PCI 3.3 (4000V)
-0.3
1.08
1.5
5.5
0.1 VCCO
0.9 VCCO
1.5
-0.5
PCI 3.3 (4000Z)
-0.3
5.5
0.1 VCCO
0.9 VCCO
1.5
-0.5
0.3 * 3.3 * (VCC / 1.8) 0.5 * 3.3 * (VCC / 1.8)
1. The average DC current drawn by I/Os between adjacent bank GND connections, or between the last GND in an I/O bank and the end of
the I/O bank, as shown in the logic signals connection table, shall not exceed n*8mA. Where n is the number of I/Os between bank GND
connections or between the last GND in a bank and the end of a bank.
3.3V VCCO
IOL
IOH
80
60
40
20
0
0.5
1.0 1.5
50
IOL
IOH
40
30
20
10
0
2.0 2.5 3.0 3.5
50
IOL
IOH
40
30
20
10
0
0.5
1.0
1.5
0.5
1.0
1.5
2.0
VO Output Voltage (V)
1.8V VCCO
60
Typical I/O Output Current (mA)
60
0
0
VO Output Voltage (V)
0
2.5V VCCO
70
Typical I/O Output Current (mA)
Typical I/O Output Current (mA)
100
2.0
VO Output Voltage (V)
18
2.5
Lattice Semiconductor
LA-ispMACH 4000V/Z Automotive Family Data Sheet
LA-ispMACH 4000V/Z External Switching Characteristics
Over Recommended Operating Conditions
LA-ispMACH 4000V
-75
Parameter
Description1, 2, 3
LA-ispMACH 4000Z
-75
Min.
Max.
Min.
Max.
Units
tPD
5-PT bypass combinatorial propagation delay
—
7.5
—
7.5
ns
tPD_MC
20-PT combinatorial propagation delay through macrocell
—
8.0
—
8.0
ns
tS
GLB register setup time before clock
4.5
—
4.5
—
ns
tST
GLB register setup time before clock with T-type register
4.7
—
4.7
—
ns
tSIR
GLB register setup time before clock, input register
path
1.7
—
1.4
—
ns
tSIRZ
GLB register setup time before clock with zero hold
2.7
—
2.7
—
ns
tH
GLB register hold time after clock
0.0
—
0.0
—
ns
tHT
GLB register hold time after clock with T-type register
0.0
—
0.0
—
ns
tHIR
GLB register hold time after clock, input register path
1.0
—
1.3
—
ns
tHIRZ
GLB register hold time after clock, input register path
with zero hold
0.0
—
0.0
—
ns
tCO
GLB register clock-to-output delay
—
4.5
—
4.5
ns
tR
External reset pin to output delay
—
9.0
—
9.0
ns
tRW
External reset pulse duration
4.0
—
4.0
—
ns
tPTOE/DIS
Input to output local product term output enable/disable
—
9.0
—
9.0
ns
tGPTOE/DIS
Input to output global product term output enable/disable
—
10.3
—
10.5
ns
tGOE/DIS
Global OE input to output enable/disable
—
7.0
—
7.0
ns
tCW
Global clock width, high or low
3.3
—
3.3
—
ns
tGW
Global gate width low (for low transparent) or high (for
high transparent)
3.3
—
3.3
—
ns
Input register clock width, high or low
3.3
—
3.3
—
ns
tWIR
fMAX
4
Clock frequency with internal feedback
fMAX (Ext.) Clock frequency with external feedback, [1/ (tS + tCO)]
1.
2.
3.
4.
168
—
168
—
MHz
111
—
111
—
MHz
Timing numbers are based on default LVCMOS 1.8 I/O buffers. Use timing adjusters provided to calculate other standards.
Measured using standard switching circuit, assuming GRP loading of 1 and 1 output switching.
Pulse widths and clock widths less than minimum will cause unknown behavior.
Standard 16-bit counter using GRP feedback.
19
Timing v.3.2
Lattice Semiconductor
LA-ispMACH 4000V/Z Automotive Family Data Sheet
Timing Model
The task of determining the timing through the LA-ispMACH 4000V/Z automotive family, like any CPLD, is relatively
simple. The timing model provided in Figure 11 shows the specific delay paths. Once the implementation of a given
function is determined either conceptually or from the software report file, the delay path of the function can easily
be determined from the timing model. The Lattice design tools report the timing delays based on the same timing
model for a particular design. Note that the internal timing parameters are given for reference only, and are not
tested. The external timing parameters are tested and guaranteed for every device. For more information on the
timing model and usage, please refer to Technical Note TN1004: ispMACH 4000 Timing Model Design and Usage
Guidelines.
Figure 11. LA-ispMACH 4000V/Z Automotive Timing Model
Routing/GLB Delays
From
Feedback
tPDb
tFBK
tPDi
IN
SCLK
tIN
tIOI
tROUTE
tBLA
tMCELL
tEXP
DATA
Q
tINREG
tINDIO
tGCLK_IN
tIOI
OE
tBUF
tIOO
tEN
tDIS
Out
In/Out
Delays
tPTCLK
tBCLK
C.E.
tPTSR
tBSR
S/R
MC Reg.
Control
Delays
tORP
Feedback
Register/Latch
Delays
tGPTOE
tPTOE
tGOE
tIOI
In/Out
Delays
Note: Italicized items are optional delay adders.
20
Lattice Semiconductor
LA-ispMACH 4000V/Z Automotive Family Data Sheet
LA-ispMACH 4000V/Z Internal Timing Parameters
Over Recommended Operating Conditions
LA-ispMACH 4000V
-75
Parameter
Description
Min.
Max.
LA-ispMACH 4000Z
-75
Min.
Max.
Units
In/Out Delays
tIN
Input Buffer Delay
—
1.50
—
1.80
ns
tGOE
Global OE Pin Delay
—
6.04
—
4.30
ns
tGCLK_IN
Global Clock Input Buffer Delay
—
2.28
—
2.15
ns
tBUF
Delay through Output Buffer
—
1.50
—
1.30
ns
tEN
Output Enable Time
—
0.96
—
2.70
ns
tDIS
Output Disable Time
—
0.96
—
2.70
ns
Routing/GLB Delays
tROUTE
Delay through GRP
—
2.26
—
2.50
ns
tMCELL
Macrocell Delay
—
1.45
—
1.00
ns
tINREG
Input Buffer to Macrocell Register Delay
—
0.96
—
1.00
ns
tFBK
Internal Feedback Delay
—
0.00
—
0.05
ns
tPDb
5-PT Bypass Propagation Delay
—
2.24
—
1.90
ns
tPDi
Macrocell Propagation Delay
—
1.24
—
1.00
ns
Register/Latch Delays
tS
D-Register Setup Time (Global Clock)
1.57
—
1.35
—
ns
tS_PT
D-Register Setup Time (Product Term Clock)
1.32
—
2.45
—
ns
tST
T-Register Setup Time (Global Clock)
1.77
—
1.55
—
ns
tST_PT
T-Register Setup Time (Product Term Clock)
1.32
—
2.75
—
ns
tH
D-Register Hold Time
2.93
—
3.15
—
ns
tHT
T-Register Hold Time
2.93
—
3.15
—
ns
tSIR
D-Input Register Setup Time (Global Clock)
1.57
—
0.75
—
tSIR_PT
D-Input Register Setup Time (Product Term
Clock)
1.45
—
tHIR
D-Input Register Hold Time (Global Clock)
1.18
—
tHIR_PT
D-Input Register Hold Time (Product Term
Clock)
1.18
—
tCOi
Register Clock to Output/Feedback MUX Time
—
tCES
Clock Enable Setup Time
2.25
tCEH
Clock Enable Hold Time
tSL
Latch Setup Time (Global Clock)
tSL_PT
Latch Setup Time (Product Term Clock)
1.32
—
2.15
—
ns
tHL
Latch Hold Time
1.17
—
1.17
—
ns
tGOi
Latch Gate to Output/Feedback MUX Time
—
0.33
—
0.33
tPDLi
Propagation Delay through Transparent Latch to
Output/Feedback MUX
—
0.25
tSRi
Asynchronous Reset or Set to Output/Feedback
MUX Delay
0.28
—
tSRR
Asynchronous Reset or Set Recovery Time
1.67
ns
ns
1.45
—
1.95
—
1.18
—
0.67
—
1.05
ns
—
2.00
—
ns
1.88
—
0.00
—
ns
1.57
—
1.65
—
ns
ns
ns
ns
ns
—
0.25
—
0.28
—
—
1.67
ns
ns
Control Delays
tBCLK
GLB PT Clock Delay
—
1.12
—
1.25
ns
tPTCLK
Macrocell PT Clock Delay
—
0.87
—
1.25
ns
21
Lattice Semiconductor
LA-ispMACH 4000V/Z Automotive Family Data Sheet
LA-ispMACH 4000V/Z Internal Timing Parameters (Cont.)
Over Recommended Operating Conditions
LA-ispMACH 4000V
-75
Parameter
Description
LA-ispMACH 4000Z
-75
Min.
Max.
Min.
Max.
Units
—
1.83
—
1.83
ns
tBSR
GLB PT Set/Reset Delay
tPTSR
Macrocell PT Set/Reset Delay
—
3.41
—
2.72
ns
tGPTOE
Global PT OE Delay
—
5.58
—
3.50
ns
tPTOE
Macrocell PT OE Delay
—
4.28
—
2.00
ns
Timing v.3.2
Note: Internal Timing Parameters are not tested and are for reference only. Refer to Timing Model in this data sheet for further details.
22
Lattice Semiconductor
LA-ispMACH 4000V/Z Automotive Family Data Sheet
LA-ispMACH 4000V/Z Timing Adders1
LA-ispMACH 4000V
-75
Adder Type
Base Parameter
Description
LA-ispMACH 4000Z
-75
Min.
Max.
Min.
Max.
Units
—
1.00
—
1.30
ns
Optional Delay Adders
tINDIO
tINREG
Input register delay
tEXP
tMCELL
Product term expander delay
—
0.33
—
0.50
ns
tORP
—
Output routing pool delay
—
0.05
—
0.40
ns
tBLA
tROUTE
Additional block loading adder
—
0.05
—
0.05
ns
tIOI Input Adjusters
LVTTL_in
tIN, tGCLK_IN, tGOE Using LVTTL standard
—
0.60
—
0.60
ns
LVCMOS33_in
tIN, tGCLK_IN, tGOE Using LVCMOS 3.3 standard
—
0.60
—
0.60
ns
LVCMOS25_in
tIN, tGCLK_IN, tGOE Using LVCMOS 2.5 standard
—
0.60
—
0.60
ns
LVCMOS18_in
tIN, tGCLK_IN, tGOE Using LVCMOS 1.8 standard
—
0.00
—
0.00
ns
PCI_in
tIN, tGCLK_IN, tGOE Using PCI compatible input
—
0.60
—
0.60
ns
tIOO Output Adjusters
Output configured as TTL buffer
—
0.20
—
0.20
ns
LVCMOS33_out tBUF, tEN, tDIS
Output configured as 3.3V buffer
—
0.20
—
0.20
ns
LVCMOS25_out tBUF, tEN, tDIS
Output configured as 2.5V buffer
—
0.10
—
0.10
ns
LVCMOS18_out tBUF, tEN, tDIS
Output configured as 1.8V buffer
—
0.00
—
0.00
ns
PCI_out
tBUF, tEN, tDIS
Output configured as PCI
compatible buffer
—
0.20
—
0.20
ns
Slow Slew
tBUF, tEN
Output configured for slow slew
rate
—
1.00
—
1.00
ns
LVTTL_out
tBUF, tEN, tDIS
Note: Open drain timing is the same as corresponding LVCMOS timing.
Timing v.3.2
1. Refer to Technical Note TN1004: ispMACH 4000 Timing Model Design and Usage Guidelines for information regarding use of these adders.
23
Lattice Semiconductor
LA-ispMACH 4000V/Z Automotive Family Data Sheet
Boundary Scan Waveforms and Timing Specifications
Symbol
Parameter
Min.
Max.
Units
tBTCP
TCK [BSCAN test] clock cycle
40
—
ns
tBTCH
TCK [BSCAN test] pulse width high
20
—
ns
tBTCL
TCK [BSCAN test] pulse width low
20
—
ns
tBTSU
TCK [BSCAN test] setup time
8
—
ns
tBTH
TCK [BSCAN test] hold time
10
—
ns
tBRF
TCK [BSCAN test] rise and fall time
50
—
mV/ns
tBTCO
TAP controller falling edge of clock to valid output
—
10
ns
tBTOZ
TAP controller falling edge of clock to data output disable
—
10
ns
tBTVO
TAP controller falling edge of clock to data output enable
—
10
ns
tBTCPSU
BSCAN test Capture register setup time
8
—
ns
tBTCPH
BSCAN test Capture register hold time
10
—
ns
tBTUCO
BSCAN test Update reg, falling edge of clock to valid output
—
25
ns
tBTUOZ
BSCAN test Update reg, falling edge of clock to output disable
—
25
ns
tBTUOV
BSCAN test Update reg, falling edge of clock to output enable
—
25
ns
24
Lattice Semiconductor
LA-ispMACH 4000V/Z Automotive Family Data Sheet
Power Consumption
LA-ispMACH 4000Z
Typical ICC vs. Frequency
(Preliminary Information)
LA-ispMACH 4000V
Typical ICC vs. Frequency
100
150
80
ICC (mA)
ICC (mA)
100
4128V
60
40
4064V
50
4128Z
20
4032V
4064Z
4032Z
0
0
50
100
150
200
250
300
350
0
0
400
Frequency (MHz)
50
100
150
200
Note: The devices are configured with the maximum number
of 16-bit counters, typical current at 3.3V, 2.5V, 25°C.
300
Note: The devices are configured with the maximum number
of 16-bit counters, typical current at 1.8V, 25°C.
Power Estimation Coefficients1
Device
250
Frequency (MHz)
A
B
LA-ispMACH 4032V
11.3
0.010
LA-ispMACH 4064V
11.5
0.010
LA-ispMACH 4128V
11.5
0.011
LA-ispMACH 4032Z
0.010
0.010
LA-ispMACH 4064Z
0.011
0.010
LA-ispMACH 4128Z
0.012
0.010
1. For further information about the use of these coefficients, refer to Technical Note
TN1005, Power Estimation in ispMACH 4000V/B/C/Z Devices.
25
Lattice Semiconductor
LA-ispMACH 4000V/Z Automotive Family Data Sheet
Switching Test Conditions
Figure 12 shows the output test load that is used for AC testing. The specific values for resistance, capacitance,
voltage, and other test conditions are shown in Table 9.
Figure 12. Output Test Load, LVTTL and LVCMOS Standards
VCCO
R1
Test
Point
DUT
R2
CL
0213A/ispm4k
Table 9. Test Fixture Required Components
Test Condition
LVCMOS I/O, (L -> H, H -> L)
R1
CL1
R2
Timing Ref.
VCCO
LVCMOS 3.3 = 1.5V
LVCMOS 3.3 = 3.0V
LVCMOS 2.5 = VCCO/2
LVCMOS 2.5 = 2.3V
106Ω 106Ω
35pF
LVCMOS 1.8 = VCCO/2
LVCMOS 1.8 = 1.65V
106Ω
35pF
1.5V
3.0V
LVCMOS I/O (Z -> H)
∞
LVCMOS I/O (Z -> L)
106Ω
∞
35pF
1.5V
3.0V
LVCMOS I/O (H -> Z)
∞
106Ω
5pF
VOH - 0.3
3.0V
LVCMOS I/O (L -> Z)
106Ω
∞
5pF
VOL + 0.3
3.0V
1. CL includes test fixtures and probe capacitance.
26
Lattice Semiconductor
LA-ispMACH 4000V/Z Automotive Family Data Sheet
Signal Descriptions
Signal Names
Description
TMS
Input – This pin is the IEEE 1149.1 Test Mode Select input, which is used to control
the state machine
TCK
Input – This pin is the IEEE 1149.1 Test Clock input pin, used to clock through the
state machine
TDI
Input – This pin is the IEEE 1149.1 Test Data In pin, used to load data
TDO
Output – This pin is the IEEE 1149.1 Test Data Out pin used to shift data out
GOE0/IO, GOE1/IO
These pins are configured to be either Global Output Enable Input or as general I/O
pins
GND
Ground
NC
Not Connected
VCC
The power supply pins for the logic core and JTAG port
CLK0/I, CLK1/I, CLK2/I, CLK3/I
These pins are configured to be either CLK input or as an input
VCCO0, VCCO1
The power supply pins for each I/O bank
Input/Output1 – These are the general purpose I/O used by the logic array. y is GLB
reference (alpha) and z is macrocell reference (numeric). z: 0-15
yzz
LA-ispMACH 4032V/Z
y: A-B
LA-ispMACH 4064V/Z
y: A-D
LA-ispMACH 4128V/Z
y: A-H
1. In some packages, certain I/Os are only available for use as inputs. See the signal connections table for details.
LA-ispMACH 4000V ORP Reference Table
4032V
Number of I/Os
301
4064V
32
302
32
4128V
64
64
923
96
Number of GLBs
2
2
4
4
4
8
8
8
Number of I/Os /GLB
16
16
8
8
16
8
12
12
Reference ORP Table
16 I/Os / GLB
8 I/Os / GLB
16 I/Os / GLB 8 I/Os /GLB
1. 32-macrocell device, 44 TQFP: 2 GLBs have 15 out of 16 I/Os bonded out.
2. 64-macrocells device, 44 TQFP: 2 GLBs have 7 out of 8 I/Os bonded out.
3. 128-macrocell device, 128 TQFP: 4 GLBs have 11 out of 12 I/Os
LA-ispMACH 4000Z ORP Reference Table
4032Z
Number of I/Os
4064Z
32
32
Number of GLBs
2
Number of I/Os / GLB
16
Reference ORP Table
16 I/Os /
GLB
27
4128Z
64
64
4
4
8
8
16
8
8 I/Os /
GLB
16 I/Os /
GLB
8 I/Os /
GLB
12 I/Os / GLB
Lattice Semiconductor
LA-ispMACH 4000V/Z Automotive Family Data Sheet
LA-ispMACH 4000V/Z Power Supply and NC Connections1
44 TQFP2
Signal
VCC
11, 33
48 TQFP2
12, 36
100 TQFP2
25, 40, 75, 90
128 TQFP2
32, 51, 96, 115
144 TQFP2
36, 57, 108, 129
VCCO0
6
VCCO (Bank 0)
6
13, 33, 95
3, 17, 30, 41, 122
VCCO1
28
VCCO (Bank 1)
30
45, 63, 83
58, 67, 81, 94, 105
GND
12, 34
13, 37
1, 26, 51, 76
1, 33, 65, 97
1, 37, 73, 109
5
5
7, 18, 32, 96
10, 24, 40, 113, 123
10, 186, 27, 46, 127,
137
27
29
46, 57, 68, 82
49, 59, 74, 88, 104
55, 65, 82, 906, 99,
118
None
None
None
None
GND (Bank 0)
GND (Bank 1)
NC
3, 19, 34, 47, 136
64, 75, 91, 106, 119
17, 20, 38, 45, 72,
89, 92, 110, 117,
144
1. All grounds must be electrically connected at the board level. However, for the purposes of I/O current loading, grounds are associated with
the bank shown.
2. Pin orientation follows the conventional order from pin 1 marking of the top side view and counter-clockwise.
28
Lattice Semiconductor
LA-ispMACH 4000V/Z Automotive Family Data Sheet
LA-ispMACH 4032V and 4064V Logic Signal Connections: 44-Pin TQFP
LA-ispMACH 4032V
LA-ispMACH 4064V
Pin Number
Bank Number
GLB/MC/Pad
ORP
GLB/MC/Pad
ORP
1
-
TDI
-
TDI
-
2
0
A5
A^5
A10
A^5
3
0
A6
A^6
A12
A^6
4
0
A7
A^7
A14
A^7
5
0
GND (Bank 0)
-
GND (Bank 0)
-
6
0
VCCO (Bank 0)
-
VCCO (Bank 0)
-
7
0
A8
A^8
B0
B^0
8
0
A9
A^9
B2
B^1
9
0
A10
A^10
B4
B^2
10
-
TCK
-
TCK
-
11
-
VCC
-
VCC
-
12
-
GND
-
GND
-
13
0
A12
A^12
B8
B^4
14
0
A13
A^13
B10
B^5
15
0
A14
A^14
B12
B^6
16
0
A15
A^15
B14
B^7
17
1
CLK2/I
-
CLK2/I
-
18
1
B0
B^0
C0
C^0
19
1
B1
B^1
C2
C^1
20
1
B2
B^2
C4
C^2
21
1
B3
B^3
C6
C^3
22
1
B4
B^4
C8
C^4
23
-
TMS
-
TMS
-
24
1
B5
B^5
C10
C^5
25
1
B6
B^6
C12
C^6
26
1
B7
B^7
C14
C^7
27
1
GND (Bank 1)
-
GND (Bank 1)
-
28
1
VCCO (Bank 1)
-
VCCO (Bank 1)
-
29
1
B8
B^8
D0
D^0
30
1
B9
B^9
D2
D^1
31
1
B10
B^10
D4
D^2
32
-
TDO
-
TDO
-
33
-
VCC
-
VCC
-
34
-
GND
-
GND
-
35
1
B12
B^12
D8
D^4
36
1
B13
B^13
D10
D^5
37
1
B14
B^14
D12
D^6
38
1
B15/GOE1
B^15
D14/GOE1
D^7
39
0
CLK0/I
-
CLK0/I
-
40
0
A0/GOE0
A^0
A0/GOE0
A^0
41
0
A1
A^1
A2
A^1
42
0
A2
A^2
A4
A^2
29
Lattice Semiconductor
LA-ispMACH 4000V/Z Automotive Family Data Sheet
LA-ispMACH 4032V and 4064V Logic Signal Connections: 44-Pin TQFP
LA-ispMACH 4032V
LA-ispMACH 4064V
Pin Number
Bank Number
GLB/MC/Pad
ORP
GLB/MC/Pad
ORP
43
0
A3
A^3
A6
A^3
44
0
A4
A^4
A8
A^4
LA-ispMACH 4032V/Z and 4064V/Z Logic Signal Connections: 48-Pin TQFP
LA-ispMACH 4032V/Z
Pin Number
ORP
LA-ispMACH 4064V/Z
Bank Number
GLB/MC/Pad
GLB/MC/Pad
ORP
1
-
TDI
-
TDI
-
2
0
A5
A^5
A10
A^5
3
0
A6
A^6
A12
A^6
4
0
A7
A^7
A14
A^7
5
0
GND (Bank 0)
-
GND (Bank 0)
-
6
0
VCCO (Bank 0)
-
VCCO (Bank 0)
-
7
0
A8
A^8
B0
B^0
8
0
A9
A^9
B2
B^1
9
0
A10
A^10
B4
B^2
10
0
A11
A^11
B6
B^3
11
-
TCK
-
TCK
-
12
-
VCC
-
VCC
-
13
-
GND
-
GND
-
14
0
A12
A^12
B8
B^4
15
0
A13
A^13
B10
B^5
16
0
A14
A^14
B12
B^6
17
0
A15
A^15
B14
B^7
18
0
CLK1/I
-
CLK1/I
-
19
1
CLK2/I
-
CLK2/I
-
20
1
B0
B^0
C0
C^0
21
1
B1
B^1
C2
C^1
22
1
B2
B^2
C4
C^2
23
1
B3
B^3
C6
C^3
24
1
B4
B^4
C8
C^4
25
-
TMS
-
TMS
-
26
1
B5
B^5
C10
C^5
27
1
B6
B^6
C12
C^6
28
1
B7
B^7
C14
C^7
29
1
GND (Bank 1)
-
GND (Bank 1)
-
30
1
VCCO (Bank 1)
-
VCCO (Bank 1)
-
31
1
B8
B^8
D0
D^0
32
1
B9
B^9
D2
D^1
33
1
B10
B^10
D4
D^2
34
1
B11
B^11
D6
D^3
35
-
TDO
-
TDO
-
30
Lattice Semiconductor
LA-ispMACH 4000V/Z Automotive Family Data Sheet
LA-ispMACH 4032V/Z and 4064V/Z Logic Signal Connections: 48-Pin TQFP
LA-ispMACH 4032V/Z
Pin Number
Bank Number
GLB/MC/Pad
ORP
36
37
-
VCC
-
GND
38
1
B12
39
1
B13
40
1
B14
41
1
B15/GOE1
42
1
43
0
44
0
45
0
46
47
48
LA-ispMACH 4064V/Z
GLB/MC/Pad
ORP
-
VCC
-
-
GND
-
B^12
D8
D^4
B^13
D10
D^5
B^14
D12
D^6
B^15
D14/GOE1
D^7
CLK3/I
-
CLK3/I
-
CLK0/I
-
CLK0/I
-
A0/GOE0
A^0
A0/GOE0
A^0
A1
A^1
A2
A^1
0
A2
A^2
A4
A^2
0
A3
A^3
A6
A^3
0
A4
A^4
A8
A^4
LA-ispMACH 4064V/Z and 4128V/Z Logic Signal Connections: 100-Pin TQFP
LA-ispMACH 4064V/Z
LA-ispMACH 4128V/Z
Pin Number
Bank Number
GLB/MC/Pad
ORP
GLB/MC/Pad
ORP
1
-
GND
-
GND
-
2
-
TDI
-
TDI
-
3
0
A8
A^8
B0
B^0
4
0
A9
A^9
B2
B^1
5
0
A10
A^10
B4
B^2
6
0
A11
A^11
B6
B^3
7
0
GND (Bank 0)
-
GND (Bank 0)
-
8
0
A12
A^12
B8
B^4
9
0
A13
A^13
B10
B^5
10
0
A14
A^14
B12
B^6
11
0
A15
A^15
B13
B^7
12*
0
I
-
I
-
13
0
VCCO (Bank 0)
-
VCCO (Bank 0)
-
14
0
B15
B^15
C14
C^7
15
0
B14
B^14
C12
C^6
16
0
B13
B^13
C10
C^5
17
0
B12
B^12
C8
C^4
18
0
GND (Bank 0)
-
GND (Bank 0)
-
19
0
B11
B^11
C6
C^3
20
0
B10
B^10
C5
C^2
21
0
B9
B^9
C4
C^1
22
0
B8
B^8
C2
C^0
23*
0
I
-
I
-
24
-
TCK
-
TCK
-
31
Lattice Semiconductor
LA-ispMACH 4000V/Z Automotive Family Data Sheet
LA-ispMACH 4064V/Z and 4128V/Z Logic Signal Connections: 100-Pin TQFP
LA-ispMACH 4064V/Z
Pin Number
Bank Number
GLB/MC/Pad
ORP
25
26
-
VCC
-
GND
LA-ispMACH 4128V/Z
GLB/MC/Pad
ORP
-
VCC
-
-
GND
-
27*
0
I
-
I
-
28
0
B7
B^7
D13
D^7
29
0
B6
B^6
D12
D^6
30
0
B5
B^5
D10
D^5
31
0
B4
B^4
D8
D^4
32
0
GND (Bank 0)
-
GND (Bank 0)
-
33
0
VCCO (Bank 0)
-
VCCO (Bank 0)
-
34
0
B3
B^3
D6
D^3
35
0
B2
B^2
D4
D^2
36
0
B1
B^1
D2
D^1
37
0
B0
B^0
D0
D^0
38
0
CLK1/I
-
CLK1/I
-
39
1
CLK2/I
-
CLK2/I
-
40
-
VCC
-
VCC
-
41
1
C0
C^0
E0
E^0
42
1
C1
C^1
E2
E^1
43
1
C2
C^2
E4
E^2
44
1
C3
C^3
E6
E^3
45
1
VCCO (Bank 1)
-
VCCO (Bank 1)
-
46
1
GND (Bank 1)
-
GND (Bank 1)
-
47
1
C4
C^4
E8
E^4
48
1
C5
C^5
E10
E^5
49
1
C6
C^6
E12
E^6
50
1
C7
C^7
E14
E^7
51
-
GND
-
GND
-
52
-
TMS
-
TMS
-
53
1
C8
C^8
F0
F^0
54
1
C9
C^9
F2
F^1
55
1
C10
C^10
F4
F^2
56
1
C11
C^11
F6
F^3
57
1
GND (Bank 1)
-
GND (Bank 1)
-
58
1
C12
C^12
F8
F^4
59
1
C13
C^13
F10
F^5
60
1
C14
C^14
F12
F^6
61
1
C15
C^15
F13
F^7
62*
1
I
-
I
-
63
1
VCCO (Bank 1)
-
VCCO (Bank 1)
-
64
1
D15
D^15
G14
G^7
65
1
D14
D^14
G12
G^6
66
1
D13
D^13
G10
G^5
67
1
D12
D^12
G8
G^4
32
Lattice Semiconductor
LA-ispMACH 4000V/Z Automotive Family Data Sheet
LA-ispMACH 4064V/Z and 4128V/Z Logic Signal Connections: 100-Pin TQFP
LA-ispMACH 4064V/Z
Pin Number
Bank Number
GLB/MC/Pad
68
1
69
1
70
71
LA-ispMACH 4128V/Z
ORP
GLB/MC/Pad
ORP
GND (Bank 1)
-
GND (Bank 1)
-
D11
D^11
G6
G^3
1
D10
D^10
G5
G^2
1
D9
D^9
G4
G^1
72
1
D8
D^8
G2
G^0
73*
1
I
-
I
-
74
-
TDO
-
TDO
-
75
-
VCC
-
VCC
-
76
-
GND
-
GND
-
77*
1
I
-
I
-
78
1
D7
D^7
H13
H^7
79
1
D6
D^6
H12
H^6
80
1
D5
D^5
H10
H^5
81
1
D4
D^4
H8
H^4
82
1
GND (Bank 1)
-
GND (Bank 1)
-
83
1
VCCO (Bank 1)
-
VCCO (Bank 1)
-
84
1
D3
D^3
H6
H^3
85
1
D2
D^2
H4
H^2
86
1
D1
D^1
H2
H^1
87
1
D0/GOE1
D^0
H0/GOE1
H^0
88
1
CLK3/I
-
CLK3/I
-
89
0
CLK0/I
-
CLK0/I
-
90
-
VCC
-
VCC
-
91
0
A0/GOE0
A^0
A0/GOE0
A^0
92
0
A1
A^1
A2
A^1
93
0
A2
A^2
A4
A^2
94
0
A3
A^3
A6
A^3
95
0
VCCO (Bank 0)
-
VCCO (Bank 0)
-
96
0
GND (Bank 0)
-
GND (Bank 0)
-
97
0
A4
A^4
A8
A^4
98
0
A5
A^5
A10
A^5
99
0
A6
A^6
A12
A^6
100
0
A7
A^7
A14
A^7
*This pin is input only.
33
Lattice Semiconductor
LA-ispMACH 4000V/Z Automotive Family Data Sheet
LA-ispMACH 4128V Logic Signal Connections: 128-Pin TQFP
LA-ispMACH 4128V
Pin Number
Bank Number
GLB/MC/Pad
ORP
1
0
GND
-
2
0
TDI
-
3
0
VCCO (Bank 0)
-
4
0
B0
B^0
5
0
B1
B^1
6
0
B2
B^2
7
0
B4
B^3
8
0
B5
B^4
9
0
B6
B^5
10
0
GND (Bank 0)
-
11
0
B8
B^6
12
0
B9
B^7
13
0
B10
B^8
14
0
B12
B^9
15
0
B13
B^10
16
0
B14
B^11
17
0
VCCO (Bank 0)
-
18
0
C14
C^11
19
0
C13
C^10
20
0
C12
C^9
21
0
C10
C^8
22
0
C9
C^7
23
0
C8
C^6
24
0
GND (Bank 0)
-
25
0
C6
C^5
26
0
C5
C^4
27
0
C4
C^3
28
0
C2
C^2
29
0
C0
C^0
30
0
VCCO (Bank 0)
-
31
0
TCK
-
32
0
VCC
-
33
0
GND
-
34
0
D14
D^11
35
0
D13
D^10
36
0
D12
D^9
37
0
D10
D^8
38
0
D9
D^7
39
0
D8
D^6
40
0
GND (Bank 0)
-
41
0
VCCO (Bank 0)
-
42
0
D6
D^5
34
Lattice Semiconductor
LA-ispMACH 4000V/Z Automotive Family Data Sheet
LA-ispMACH 4128V Logic Signal Connections: 128-Pin TQFP (Cont.)
LA-ispMACH 4128V
Pin Number
Bank Number
GLB/MC/Pad
ORP
43
0
D5
D^4
44
0
D4
D^3
45
0
D2
D^2
46
0
D1
D^1
47
0
D0
D^0
48
0
CLK1/I
-
49
1
GND (Bank 1)
-
50
1
CLK2/I
-
51
1
VCC
-
52
1
E0
E^0
53
1
E1
E^1
54
1
E2
E^2
55
1
E4
E^3
56
1
E5
E^4
57
1
E6
E^5
58
1
VCCO (Bank 1)
-
59
1
GND (Bank 1)
-
60
1
E8
E^6
61
1
E9
E^7
62
1
E10
E^8
63
1
E12
E^9
64
1
E14
E^11
65
1
GND
-
66
1
TMS
-
67
1
VCCO (Bank 1)
-
68
1
F0
F^0
69
1
F1
F^1
70
1
F2
F^2
71
1
F4
F^3
72
1
F5
F^4
73
1
F6
F^5
74
1
GND (Bank 1)
-
75
1
F8
F^6
76
1
F9
F^7
77
1
F10
F^8
78
1
F12
F^9
79
1
F13
F^10
80
1
F14
F^11
81
1
VCCO (Bank 1)
-
82
1
G14
G^11
83
1
G13
G^10
84
1
G12
G^9
85
1
G10
G^8
35
Lattice Semiconductor
LA-ispMACH 4000V/Z Automotive Family Data Sheet
LA-ispMACH 4128V Logic Signal Connections: 128-Pin TQFP (Cont.)
LA-ispMACH 4128V
Pin Number
Bank Number
GLB/MC/Pad
ORP
86
1
G9
G^7
87
1
G8
G^6
88
1
GND (Bank 1)
-
89
1
G6
G^5
90
1
G5
G^4
91
1
G4
G^3
92
1
G2
G^2
93
1
G0
G^0
94
1
VCCO (Bank 1)
-
95
1
TDO
-
96
1
VCC
-
97
1
GND
-
98
1
H14
H^11
99
1
H13
H^10
100
1
H12
H^9
101
1
H10
H^8
102
1
H9
H^7
103
1
H8
H^6
104
1
GND (Bank 1)
-
105
1
VCCO (Bank 1)
-
106
1
H6
H^5
107
1
H5
H^4
108
1
H4
H^3
109
1
H2
H^2
110
1
H1
H^1
111
1
H0/GOE1
H^0
112
1
CLK3/I
-
113
0
GND (Bank 0)
-
114
0
CLK0/I
-
115
0
VCC
-
116
0
A0/GOE0
A^0
117
0
A1
A^1
118
0
A2
A^2
119
0
A4
A^3
120
0
A5
A^4
121
0
A6
A^5
122
0
VCCO (Bank 0)
-
123
0
GND (Bank 0)
-
124
0
A8
A^6
125
0
A9
A^7
126
0
A10
A^8
127
0
A12
A^9
128
0
A14
A^11
36
Lattice Semiconductor
LA-ispMACH 4000V/Z Automotive Family Data Sheet
LA-ispMACH 4128V Logic Signal Connections: 144-Pin TQFP
LA-ispMACH 4128V
Pin Number
Bank Number
GLB/MC/Pad
ORP
1
-
GND
-
2
-
TDI
-
3
0
VCCO (Bank 0)
-
4
0
B0
B^0
5
0
B1
B^1
6
0
B2
B^2
7
0
B4
B^3
8
0
B5
B^4
9
0
B6
B^5
10
0
GND (Bank 0)
-
11
0
B8
B^6
12
0
B9
B^7
13
0
B10
B^8
14
0
B12
B^9
15
0
B13
B^10
16
0
B14
B^11
17
-
NC
1
18
0
GND (Bank 0)
-
19
0
VCCO (Bank 0)
-
20
0
NC
-
21
0
C14
C^11
22
0
C13
C^10
23
0
C12
C^9
24
0
C10
C^8
25
0
C9
C^7
26
0
C8
C^6
27
0
GND (Bank 0)
-
28
0
C6
C^5
29
0
C5
C^4
30
0
C4
C^3
31
0
C2
C^2
32
0
C1
C^1
33
0
C0
C^0
34
0
VCCO (Bank 0)
-
35
-
TCK
-
36
-
VCC
-
37
-
GND
-
38
0
NC
-
39
0
D14
D^11
40
0
D13
D^10
41
0
D12
D^9
42
0
D10
D^8
37
Lattice Semiconductor
LA-ispMACH 4000V/Z Automotive Family Data Sheet
LA-ispMACH 4128V Logic Signal Connections: 144-Pin TQFP (Cont.)
LA-ispMACH 4128V
Pin Number
Bank Number
GLB/MC/Pad
ORP
43
0
D9
D^7
44
0
D8
D^6
45
0
NC
-
46
0
GND (Bank 0)
-
47
0
VCCO (Bank 0)
-
48
0
D6
D^5
49
0
D5
D^4
50
0
D4
D^3
51
0
D2
D^2
52
0
D1
D^1
53
0
D0
D^0
54
0
CLK1/I
-
55
1
GND (Bank 1)
-
56
1
CLK2/I
-
57
-
VCC
-
58
1
E0
E^0
59
1
E1
E^1
60
1
E2
E^2
61
1
E4
E^3
62
1
E5
E^4
63
1
E6
E^5
64
1
VCCO (Bank 1)
-
65
1
GND (Bank 1)
-
66
1
E8
E^6
67
1
E9
E^7
68
1
E10
E^8
69
1
E12
E^9
70
1
E13
E^10
71
1
E14
E^11
72
1
NC
-
73
-
GND
-
74
-
TMS
-
75
1
VCCO (Bank 1)
-
76
1
F0
F^0
77
1
F1
F^1
78
1
F2
F^2
79
1
F4
F^3
80
1
F5
F^4
81
1
F6
F^5
82
1
GND (Bank 1)
-
83
1
F8
F^6
84
1
F9
F^7
85
1
F10
F^8
38
Lattice Semiconductor
LA-ispMACH 4000V/Z Automotive Family Data Sheet
LA-ispMACH 4128V Logic Signal Connections: 144-Pin TQFP (Cont.)
LA-ispMACH 4128V
Pin Number
Bank Number
GLB/MC/Pad
ORP
86
1
F12
F^9
87
1
F13
F^10
88
1
F14
F^11
89
1
NC
1
90
1
GND (Bank 1)
-
91
1
VCCO (Bank 1)
-
92
1
NC
-
93
1
G14
G^11
94
1
G13
G^10
95
1
G12
G^9
96
1
G10
G^8
97
1
G9
G^7
98
1
G8
G^6
99
1
GND (Bank 1)
-
100
1
G6
G^5
101
1
G5
G^4
102
1
G4
G^3
103
1
G2
G^2
104
1
G1
G^1
105
1
G0
G^0
106
1
VCCO (Bank 1)
-
107
-
TDO
-
108
-
VCC
-
109
-
GND
-
110
1
NC
-
111
1
H14
H^11
112
1
H13
H^10
113
1
H12
H^9
114
1
H10
H^8
115
1
H9
H^7
116
1
H8
H^6
117
1
NC
-
118
1
GND (Bank 1)
-
119
1
VCCO (Bank 1)
-
120
1
H6
H^5
121
1
H5
H^4
122
1
H4
H^3
123
1
H2
H^2
124
1
H1
H^1
125
1
H0/GOE1
H^0
126
1
CLK3/I
-
127
0
GND (Bank 0)
-
128
0
CLK0/I
-
39
Lattice Semiconductor
LA-ispMACH 4000V/Z Automotive Family Data Sheet
LA-ispMACH 4128V Logic Signal Connections: 144-Pin TQFP (Cont.)
LA-ispMACH 4128V
Pin Number
Bank Number
GLB/MC/Pad
ORP
129
-
VCC
-
130
0
A0/GOE0
A^0
131
0
A1
A^1
132
0
A2
A^2
133
0
A4
A^3
134
0
A5
A^4
135
0
A6
A^5
136
0
VCCO (Bank 0)
-
137
0
GND (Bank 0)
-
138
0
A8
A^6
139
0
A9
A^7
140
0
A10
A^8
141
0
A12
A^9
142
0
A13
A^10
143
0
A14
A^11
144
0
NC2
-
1. For device migration considerations, these NC pins are GND pins for I/O banks in LA-ispMACH 4128V devices.
40
Lattice Semiconductor
LA-ispMACH 4000V/Z Automotive Family Data Sheet
Part Number Description
LA XXXX XX – XX XX XXX X
Device Family
Operating Temperature Range
E = Automotive
Device Number
4032 = 32 Macrocells
4064 = 64 Macrocells
4128 = 128 Macrocells
Pin/Ball Count
44 (1.0mm thickness)
48 (1.0mm thickness)
100
128
144
Power
Blank = Low Power
Z = Zero Power
Package
TN = Lead-free TQFP
Supply Voltage
V = 3.3V
C = 1.8V
Speed
75 = 7.5ns
Ordering Information
Device
LA4032V
LA4064V
LA4128V
LA4032Z
LA4064Z
LA4128Z
Part Number
Pin/Ball
Count
I/O
Grade
48
32
E
Lead-free TQFP
44
30
E
Lead-free TQFP
100
64
E
7.5
Lead-free TQFP
48
32
E
7.5
Lead-free TQFP
44
30
E
3.3
7.5
Lead-free TQFP
144
96
E
3.3
7.5
Lead-free TQFP
128
92
E
128
3.3
7.5
Lead-free TQFP
100
64
E
32
1.8
7.5
Lead-free TQFP
48
32
E
Macrocells
Voltage
tPD
Package
LA4032V-75TN48E
32
3.3
7.5
Lead-free TQFP
LA4032V-75TN44E
32
3.3
7.5
LA4064V-75TN100E
64
3.3
7.5
LA4064V-75TN48E
64
3.3
LA4064V-75TN44E
64
3.3
LA4128V-75TN144E
128
LA4128V-75TN128E
128
LA4128V-75TN100E
LA4032ZC-75TN48E
LA4064ZC-75TN100E
64
1.8
7.5
Lead-free TQFP
100
64
E
LA4064ZC-75TN48E
64
1.8
7.5
Lead-free TQFP
48
32
E
LA4128ZC-75TN100E
128
1.8
7.5
Lead-free TQFP
100
64
E
Automotive Disclaimer
Products are not designed, intended or warranted to be fail-safe and are not designed, intended or warranted for
use in applications related to the deployment of airbags. Further, products are not intended to be used, designed or
warranted for use in applications that affect the control of the vehicle unless there is a fail-safe or redundancy feature and also a warning signal to the operator of the vehicle upon failure. Use of products in such applications is
fully at the risk of the customer, subject to applicable laws and regulations governing limitations on product liability.
For Further Information
In addition to this data sheet, the following technical notes may be helpful when designing with the LA-ispMACH
4000V/Z automotive family:
• ispMACH 4000 Timing Model Design and Usage Guidelines (TN1004)
• ispMACH 4000V/B/C/Z Power Consumption (TN1005)
41
Lattice Semiconductor
LA-ispMACH 4000V/Z Automotive Family Data Sheet
Revision History
Date
Version
Change Summary
April 2006
01.0
Initial release.
October 2006
02.0
Added LA-ispMACH 4000Z support information throughout.
March 2007
02.1
Updated ispMACH 4000 Introduction section.
Updated Signal Descriptions table.
September 2007
02.2
DC Electrical Characteristics table, removed duplicate specifications.
July 2008
02.3
Lowered the maximum supply current at 85°C to match the commercial product values.
Added automotive disclaimer.
42