TI PCA9554APW

PCA9554A
REMOTE 8-BIT
AND SMBus I/O EXPANDER
WITH INTERRUPT OUTPUT AND CONFIGURATION REGISTERS
I2C
www.ti.com
SCPS127A – SEPTEMBER 2006 – REVISED FEBRUARY 2007
FEATURES
•
RGV PACKAGE
(TOP VIEW)
14
4
13
5
12
6
11
7
10
8
9
16 15 14 13
A2 1
12 SCL
P0 2
11
P1 3
10 P7
P2 4
9 P6
5
6
7
8
INT
A2
P0
P1
P2
16 15 14 13
12 SCL
2
11 INT
10 P7
3
1
9 P6
4
5 6 7
8
P3
GND
P4
P5
3
VCC
SDA
SCL
INT
P7
P6
P5
P4
P5
15
P4
16
2
GND
1
P3
A0
A1
A2
P0
P1
P2
P3
GND
RGT PACKAGE
(TOP VIEW)
A1
A0
VCC
SDA
A1
DB, DBQ, DGV, DW,
OR PW PACKAGE
(TOP VIEW)
•
SDA
•
•
•
Power-Up With All Channels Configured as
Inputs
No Glitch on Power-Up
Latched Outputs With High-Current Drive
Maximum Capability for Directly Driving LEDs
Latch-Up Performance Exceeds 100 mA Per
JESD 78, Class II
ESD Protection Exceeds JESD 22
– 2000-V Human-Body Model (A114-A)
– 200-V Machine Model (A115-A)
– 1000-V Charged-Device Model (C101)
•
•
VCC
•
•
•
•
I2C to Parallel Port Expander
Open-Drain Active-Low Interrupt Output
Operating Power-Supply Voltage Range of
2.3 V to 5.5 V
5-V Tolerant I/Os
400-kHz Fast I2C Bus
Three Hardware Address Pins Allow up to
Eight Devices on the I2C/SMBus
Input/Output Configuration Register
Polarity Inversion Register
Internal Power-On Reset
A0
•
•
•
DESCRIPTION/ORDERING INFORMATION
This 8-bit I/O expander for the two-line bidirectional bus (I2C) is designed for 2.3-V to 5.5-V VCC operation. It
provides general-purpose remote I/O expansion for most microcontroller families via the I2C interface [serial
clock (SCL), serial data (SDA)].
The PCA9554A consists of one 8-bit Configuration (input or output selection), Input, Output, and Polarity
Inversion (active high or active low) registers. At power-on, the I/Os are configured as inputs with a weak pull up
to VCC. However, the system master can enable the I/Os as either inputs or outputs by writing to the I/O
configuration bits. The data for each input or output is kept in the corresponding Input or Output register. The
polarity of the Input Port register can be inverted with the Polarity Inversion register. All registers can be read by
the system master.
The system master can reset the PCA9554A in the event of a timeout or other improper operation by utilizing
the power-on reset feature which puts the registers in their default state and initializes the I2C/SMBus state
machine.
The PCA9554A open-drain interrupt (INT) output is activated when any input state differs from its corresponding
Input Port register state and is used to indicate to the system master that an input state has changed.
INT can be connected to the interrupt input of a microcontroller. By sending an interrupt signal on this line, the
remote I/O can inform the microcontroller if there is incoming data on its ports without having to communicate via
the I2C bus. Thus, the PCA9554A can remain a simple slave device.
The device's outputs (latched) have high-current drive capability for directly driving LEDs and low current
consumption.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas
Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
UNLESS OTHERWISE NOTED this document contains
PRODUCTION DATA information current as of publication date.
Products conform to specifications per the terms of Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2006–2007, Texas Instruments Incorporated
PCA9554A
REMOTE 8-BIT I2C AND SMBus I/O EXPANDER
WITH INTERRUPT OUTPUT AND CONFIGURATION REGISTERS
www.ti.com
SCPS127A – SEPTEMBER 2006 – REVISED FEBRUARY 2007
Three hardware pins (A0, A1, and A2) are used to program and vary the fixed I2C address and allow up to eight
devices to share the same I2C bus or SMBus.
The PCA9554A is pin-to-pin and I2C address compatible with the PCF8574A. However, software changes are
required, due to the enhancements in the PCA9554A over the PCF8574A.
The PCA9554A and PCA9554 are identical except for their fixed I2C address. This allows for up to sixteen of
these devices (eight of each) on the same I2C/SMBus.
ORDERING INFORMATION
PACKAGE (1)
TA
PCA9554ARGTR
PREVIEW
QFN – RGV
Reel of 2500
PCA9554ARGVR
PREVIEW
Tube of 75
PCA9554ADBQ
Reel of 2500
PCA9554ADBQR
Tube of 40
PCA9554ADW
Reel of 2000
PCA9554ADWR
SOIC – DW
–40°C to 85°C
SSOP – DB
TSSOP – PW
TVSOP – DGV
2
TOP-SIDE MARKING
Reel of 3000
QSOP – DBQ
(1)
ORDERABLE PART NUMBER
QFN – RGT
Tube of 80
PD554A
PREVIEW
PCA9554ADB
PCA9554ADBG4
Reel of 2000
PCA9554ADBR
Tube of 90
PCA9554APW
Reel of 2000
PCA9554APWR
Reel of 2000
PCA9554ADGVR
Reel of 125
PCA9554ADGV
PD554A
PD554A
PD554A
Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines are available at
www.ti.com/sc/package.
Submit Documentation Feedback
PCA9554A
REMOTE 8-BIT
AND SMBus I/O EXPANDER
WITH INTERRUPT OUTPUT AND CONFIGURATION REGISTERS
I2C
www.ti.com
SCPS127A – SEPTEMBER 2006 – REVISED FEBRUARY 2007
TERMINAL FUNCTIONS
NO.
QSOP (DBQ)
SOIC (DW),
SSOP (DB),
TSSOP (PW), AND
TVSOP (DGV)
QFN (RGT) AND
QFN (RGV)
NAME
1
15
A0
Address input. Connect directly to VCC or ground.
2
16
A1
Address input. Connect directly to VCC or ground.
3
1
A2
Address input. Connect directly to VCC or ground.
4
2
P0
P-port input/output. Push-pull design structure.
5
3
P1
P-port input/output. Push-pull design structure.
6
4
P2
P-port input/output. Push-pull design structure.
7
5
P3
P-port input/output. Push-pull design structure.
8
6
GND
9
7
P4
P-port input/output. Push-pull design structure.
10
8
P5
P-port input/output. Push-pull design structure.
11
9
P6
P-port input/output. Push-pull design structure.
12
10
P7
P-port input/output. Push-pull design structure.
13
11
INT
Interrupt output. Connect to VCC through a pullup resistor.
14
12
SCL
Serial clock bus. Connect to VCC through a pullup resistor.
15
13
SDA
Serial data bus. Connect to VCC through a pullup resistor.
16
14
VCC
Supply voltage
DESCRIPTION
Ground
FUNCTIONAL BLOCK DIAGRAM
INT
A0
A1
A2
SCL
SDA
13
Interrupt
Logic
LP Filter
1
2
3
14
15
Input
Filter
I2C Bus
Control
P7−P0
Shift
Register
8 Bits
I/O
Port
Write Pulse
VCC
GND
16
8
Power-On
Reset
Read Pulse
A.
Pin numbers shown are for the DB, DBQ, DGV, DW, N, or PW package.
B.
All I/Os are set to inputs at reset.
Submit Documentation Feedback
3
PCA9554A
REMOTE 8-BIT I2C AND SMBus I/O EXPANDER
WITH INTERRUPT OUTPUT AND CONFIGURATION REGISTERS
www.ti.com
SCPS127A – SEPTEMBER 2006 – REVISED FEBRUARY 2007
Simplified Schematic of P0 to P7
Data From
Shift Register
Data From
Shift Register
Output Port
Register Data
Configuration
Register
D
VCC
Q1
Q
FF
Write Configuration
Pulse
CK Q
100 kW
D
Q
FF
Write Pulse
P0 to P7
CK Q
Q2
Output Port
Register
Input Port
Register
D
Q
FF
Read Pulse
GND
Input Port
Register Data
CK Q
INT
Data From
Shift Register
D
Write Polarity
Pulse
CK Q
Q
Polarity
Register Data
FF
Polarity
Inversion
Register
A.
At power-on reset, all registers return to default values.
I/O Port
When an I/O is configured as an input, FETs Q1 and Q2 are off, which creates a high impedance input with a
weak pullup (100 kΩ typ) to VCC. The input voltage may be raised above VCC to a maximum of 5.5 V.
If the I/O is configured as an output, Q1 or Q2 is enabled, depending on the state of the output port register. In
this case, there are low impedance paths between the I/O pin and either VCC or GND. The external voltage
applied to this I/O pin should not exceed the recommended levels for proper operation.
I2C Interface
The bidirectional I2C bus consists of the serial clock (SCL) and serial data (SDA) lines. Both lines must be
connected to a positive supply through a pull-up resistor when connected to the output stages of a device. Data
transfer may be initiated only when the bus is not busy.
I2C communication with this device is initiated by a master sending a start condition, a high-to-low transition on
the SDA input/output while the SCL input is high (see Figure 1). After the start condition, the device address
byte is sent, MSB first, including the data direction bit /W).
After receiving the valid address byte, this device responds with an acknowledge (ACK), a low on the SDA
input/output during the high of the ACK-related clock pulse. The address inputs (A0–A2) of the slave device
must not be changed between the start and the stop conditions.
On the I2C bus, only one data bit is transferred during each clock pulse. The data on the SDA line must remain
stable during the high pulse of the clock period, as changes in the data line at this time are interpreted as control
commands (start or stop) (see Figure 2).
4
Submit Documentation Feedback
PCA9554A
REMOTE 8-BIT
AND SMBus I/O EXPANDER
WITH INTERRUPT OUTPUT AND CONFIGURATION REGISTERS
I2C
www.ti.com
SCPS127A – SEPTEMBER 2006 – REVISED FEBRUARY 2007
A Stop condition, a low-to-high transition on the SDA input/output while the SCL input is high, is sent by the
master (see Figure 1).
Any number of data bytes can be transferred from the transmitter to receiver between the Start and Stop
conditions. Each byte of eight bits is followed by one ACK bit. The transmitter must release the SDA line before
the receiver can send an ACK bit. The device that acknowledges must pull down the SDA line during the ACK
clock pulse so that the SDA line is stable low during the high pulse of the ACK-related clock period (see
Figure 3). When a slave receiver is addressed, it must generate an ACK after each byte is received. Similarly,
the master must generate an ACK after each byte that it receives from the slave transmitter. Setup and hold
times must be met to ensure proper operation.
A master receiver will signal an end of data to the slave transmitter by not generating an acknowledge (NACK)
after the last byte has been clocked out of the slave. This is done by the master receiver by holding the SDA line
high. In this event, the transmitter must release the data line to enable the master to generate a Stop condition.
SDA
SCL
S
P
Start Condition
Stop Condition
Figure 1. Definition of Start and Stop Conditions
SDA
SCL
Data Line
Stable;
Data Valid
Change
of Data
Allowed
Figure 2. Bit Transfer
Submit Documentation Feedback
5
PCA9554A
REMOTE 8-BIT I2C AND SMBus I/O EXPANDER
WITH INTERRUPT OUTPUT AND CONFIGURATION REGISTERS
www.ti.com
SCPS127A – SEPTEMBER 2006 – REVISED FEBRUARY 2007
Data Output
by Transmitter
NACK
Data Output
by Receiver
ACK
SCL From
Master
1
2
8
9
S
Clock Pulse for
Acknowledgment
Start
Condition
Figure 3. Acknowledgment on the I2C Bus
Interface Definition
BYTE
I2C
slave address
Px I/O data bus
6
BIT
7 (MSB)
6
5
4
3
2
1
0 (LSB)
L
H
H
H
A2
A1
A0
R/W
P7
P6
P5
P4
P3
P2
P1
P0
Submit Documentation Feedback
PCA9554A
REMOTE 8-BIT
AND SMBus I/O EXPANDER
WITH INTERRUPT OUTPUT AND CONFIGURATION REGISTERS
I2C
www.ti.com
SCPS127A – SEPTEMBER 2006 – REVISED FEBRUARY 2007
Device Address
Figure 4 shows the address byte for the PCA9554A.
Slave Address
0
1
1
1
A2
A1
A0 R/W
Hardware
Selectable
Fixed
Figure 4. PCA9554A Address
Address Reference
INPUTS
I2C BUS SLAVE ADDRESS
A2
A1
A0
L
L
L
L
L
H
57 (decimal), 39 (hexadecimal)
L
H
L
58 (decimal), 3A (hexadecimal)
56 (decimal), 38 (hexadecimal)
L
H
H
59 (decimal), 3B (hexadecimal)
H
L
L
60 (decimal), 3C (hexadecimal)
H
L
H
61 (decimal), 3D (hexadecimal)
H
H
L
62 (decimal), 3E (hexadecimal)
H
H
H
63 (decimal), 3F (hexadecimal)
The last bit of the slave address defines the operation (read or write) to be performed. When it is high (1), a read
is selected. A low (0) selects a write operation.
Control Register and Command Byte
Following the successful acknowledgment of the address byte, the bus master sends a command byte that is
stored in the control register in the PCA9554A. Two bits of this command byte state the operation (read or write)
and the internal register (input, output, polarity inversion or configuration) that will be affected. This register can
be written or read through the I2C bus. The command byte is sent only during a write transmission.
Once a command byte has been sent, the register that was addressed continues to be accessed by reads until
a new command byte has been sent.
0
0
0
0
0
0
B1
B0
Figure 5. Control Register Bits
Command Byte
CONTROL REGISTER BITS
B1
B0
COMMAND BYTE
(HEX)
0
0
0x00
0
1
0x01
1
0
0x02
1
1
0x03
PROTOCOL
POWER-UP
DEFAULT
Input Port Register
Read byte
XXXX XXXX
Output Port Register
Read/write byte
1111 1111
Polarity Inversion Register
Read/write byte
0000 0000
Configuration Register
Read/write byte
1111 1111
REGISTER
Submit Documentation Feedback
7
PCA9554A
REMOTE 8-BIT I2C AND SMBus I/O EXPANDER
WITH INTERRUPT OUTPUT AND CONFIGURATION REGISTERS
www.ti.com
SCPS127A – SEPTEMBER 2006 – REVISED FEBRUARY 2007
Register Descriptions
The Input Port Register (Register 0) reflects the incoming logic levels of the pins, regardless of whether the pin
is defined as an input or an output by the Configuration Register. It only acts on read operation. Writes to these
registers have no effect. The default value, X, is determined by the externally applied logic level.
Before a read operation, a write transmission is sent with the command byte to let the I2C device know that the
Input Port register will be accessed next.
Register 0 (Input Port Register) Table
BIT
I7
I6
I5
I4
I3
I2
I1
I0
DEFAULT
X
X
X
X
X
X
X
X
The Output Port register (register 1) shows the outgoing logic levels of the pins defined as outputs by the
Configuration register. Bit values in this register have no effect on pins defined as inputs. In turn, reads from this
register reflect the value that is in the flip-flop controlling the output selection, not the actual pin value.
Register 1 (Output Port Register) Table
BIT
O7
O6
O5
O4
O3
O2
O1
O0
DEFAULT
1
1
1
1
1
1
1
1
The Polarity Inversion register (register 2) allows polarity inversion of pins defined as inputs by the Configuration
register. If a bit in this register is set (written with 1), the corresponding port pin polarity is inverted. If a bit in this
register is cleared (written with a 0), the corresponding port pin original polarity is retained.
Register 2 (Polarity Inversion Register) Table
BIT
N7
N6
N5
N4
N3
N2
N1
N0
DEFAULT
0
0
0
0
0
0
0
0
The Configuration register (register 3) configures the directions of the I/O pins. If a bit in this register is set to 1,
the corresponding port pin is enabled as an input with high impedance output driver. If a bit in this register is
cleared to 0, the corresponding port pin is enabled as an output.
Register 3 (Configuration Register) Table
BIT
C7
C6
C5
C4
C3
C2
C1
C0
DEFAULT
1
1
1
1
1
1
1
1
Power-On Reset
When power (from 0 V) is applied to VCC, an internal power-on reset holds the PCA9554A in a reset condition
until VCC has reached VPOR. At that point, the reset condition is released and the PCA9554A registers and
I2C/SMBus state machine will initialize to their default states. After that, VCC must be lowered to below 0.2 V and
then back up to the operating voltage for a power-reset cycle.
8
Submit Documentation Feedback
PCA9554A
REMOTE 8-BIT
AND SMBus I/O EXPANDER
WITH INTERRUPT OUTPUT AND CONFIGURATION REGISTERS
I2C
www.ti.com
SCPS127A – SEPTEMBER 2006 – REVISED FEBRUARY 2007
Interrupt Output (INT)
An interrupt is generated by any rising or falling edge of the port inputs in the input mode. After time tiv, the
signal INT is valid. Resetting the interrupt circuit is achieved when data on the port is changed to the original
setting; data is read from the port that generated the interrupt or in a Stop event. Resetting occurs in the read
mode at the acknowledge (ACK) bit or not acknowledge (NACK) bit after the rising edge of the SCL signal. In a
Stop event, INT is cleared after the rising edge of SDA. Interrupts that occur during the ACK or NACK clock
pulse can be lost (or be very short) due to the resetting of the interrupt during this pulse. Each change of the
I/Os after resetting is detected and is transmitted as INT.
Reading from or writing to another device does not affect the interrupt circuit, and a pin configured as an output
cannot cause an interrupt. Changing an I/O from an output to an input may cause a false interrupt to occur if the
state of the pin does not match the contents of the Input Port register.
INT has an open-drain structure and requires a pullup resistor to VCC.
Bus Transactions
Data is exchanged between the master and PCA9554A through write and read commands.
Writes
Data is transmitted to the PCA9554A by sending the device address and setting the least-significant bit to a
logic 0 (see Figure 4 for device address). The command byte is sent after the address and determines which
register receives the data that follows the command byte. There is no limitation on the number of data bytes sent
in one write transmission.
SCL
1
2
3
4
5
6
7
8
9
Slave Address
S
SDA
0
1
1
Command Byte
1 A2 A1 A0 0
A
0
0
0
0
0
0
0
1
Data 1
A
A
P
ACK From Slave
ACK From Slave
R/W ACK From Slave
Start Condition
Data to Port
Write to Port
Data Out
From Port
Data 1 Valid
tpv
Figure 6. Write to Output Port Register
<br/>
SCL
1
2
3
4
5
6
7
8
9
Slave Address
SDA
S
0
1
1
Command Byte
1 A2 A1 A0 0
Start Condition
R/W
A
0
0
0
0
ACK From Slave
0
0
Data to Register
1 1/0 A
Data
ACK From Slave
A
P
ACK From Slave
Data to
Register
Figure 7. Write to Configuration or Polarity Inversion Registers
Submit Documentation Feedback
9
PCA9554A
REMOTE 8-BIT I2C AND SMBus I/O EXPANDER
WITH INTERRUPT OUTPUT AND CONFIGURATION REGISTERS
www.ti.com
SCPS127A – SEPTEMBER 2006 – REVISED FEBRUARY 2007
Reads
The bus master first must send the PCA9554A address with the least-significant bit set to a logic 0 (see Figure 4
for device address). The command byte is sent after the address and determines which register is accessed.
After a restart, the device address is sent again, but this time the least-significant bit is set to a logic 1. Data
from the register defined by the command byte then is sent by the PCA9554A (see Figure 8 and Figure 9). After
a restart, the value of the register defined by the command byte matches the register being accessed when the
restart occurred. Data is clocked into the register on the rising edge of the ACK clock pulse. There is no
limitation on the number of data bytes received in one read transmission, but when the final byte is received, the
bus master must not acknowledge the data.
S 0
1
1
ACK From
Slave
ACK From
Slave
Slave Address
1 A2 A1 A0 0
Command Byte
A
A S 0
ACK From
ACK From
Master
Slave Data from Register
Slave Address
1
1
Data
A
Data from Register
NACK From
Master
1 A2 A1 A0 1 A
R/W
R/W
Data
NA P
Last Byte
Figure 8. Read From Register
<br/>
1
SCL
2
3
4
5
6
7
8
9
Data From Port
Slave Address
S 0
SDA
1
Start
Condition
1
1 A2 A1 A0 0
R/W
Data 1
A
Data From Port
Data 4
A
ACK From
Slave
ACK From
Master
NA P
NACK From
Master
Stop
Condition
Read From
Port
Data Into
Port
Data 2
tph
Data 3
Data 4
Data 5
tps
INT
tiv
tir
A.
This figure assumes the command byte has previously been programmed with 00h.
B.
Transfer of data can be stopped at any moment by a stop condition.
C.
This figure eliminates the command byte transfer, a restart, and slave address call between the initial slave address
call and actual data transfer from the P port. See Figure 8 for these details.
Figure 9. Read From Input Port Register
10
Submit Documentation Feedback
PCA9554A
REMOTE 8-BIT
AND SMBus I/O EXPANDER
WITH INTERRUPT OUTPUT AND CONFIGURATION REGISTERS
I2C
www.ti.com
SCPS127A – SEPTEMBER 2006 – REVISED FEBRUARY 2007
Absolute Maximum Ratings
(1)
over operating free-air temperature range (unless otherwise noted)
MIN
MAX
VCC
Supply voltage range
–0.5
6
V
VI
Input voltage range (2)
–0.5
6
V
range (2)
VO
Output voltage
IIK
Input clamp current
VI < 0
–20
mA
IOK
Output clamp current
VO < 0
–20
mA
IIOK
Input/output clamp current
VO < 0 or VO > VCC
±20
mA
IOL
Continuous output low current
VO = 0 to VCC
50
mA
IOH
Continuous output high current
VO = 0 to VCC
–50
mA
Continuous current through GND
–250
mA
Continuous current through VCC
160
mA
ICC
θJA
–0.5
Package thermal impedance (3)
DB package
82
DBQ package
90
DGV package
120
DW package
57
PW package
108
RGT package
TBD
RGV package
Tstg
(1)
(2)
(3)
6
UNIT
Storage temperature range
V
°C/W
TBD
–65
150
°C
Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating
conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
The input negative-voltage and output voltage ratings may be exceeded if the input and output current ratings are observed.
The package thermal impedance is calculated in accordance with JESD 51-7.
Recommended Operating Conditions
VCC
Supply voltage
VIH
High-level input voltage
MIN
MAX
2.3
5.5
0.7 ×
VCC
5.5
2
5.5
SCL, SDA
–0.5
0.3 × VCC
A2–A0, P7–P0
–0.5
0.8
SCL, SDA
A2–A0, P7–P0
UNIT
V
V
VIL
Low-level input voltage
IOH
High-level output current
P7–P0
–10
mA
IOL
Low-level output current
P7–P0
25
mA
TA
Operating free-air temperature
85
°C
–40
Submit Documentation Feedback
V
11
PCA9554A
REMOTE 8-BIT I2C AND SMBus I/O EXPANDER
WITH INTERRUPT OUTPUT AND CONFIGURATION REGISTERS
www.ti.com
SCPS127A – SEPTEMBER 2006 – REVISED FEBRUARY 2007
Electrical Characteristics
over operating free-air temperature range (unless otherwise noted)
PARAMETER
TEST CONDITIONS
VIK
Input diode clamp voltage
II = –18 mA
VPOR
Power-on reset voltage
VI = VCC or GND, IO = 0
IOH = –8 mA
P-port high-level output voltage (2)
VOH
IOH = –10 mA
SDA
VOL = 0.4 V
VOL = 0.5 V
P port (3)
IOL
VOL = 0.7 V
INT
SCL, SDA
II
A2–A0
VCC
MIN
2.3 V to 5.5 V
–1.2
VPOR
2.3 V
1.8
3V
2.6
4.5 V
3.1
4.75 V
4.1
2.3 V
1.7
3V
2.5
TYP (1)
MAX
1.5
1.65
UNIT
V
V
V
4.5 V
3
4.75 V
4
2.3 V to 5.5 V
3
8
2.3 V
8
10
3V
8
14
4.5 V
8
17
4.75 V
8
35
2.3 V
10
13
3V
10
19
4.5 V
10
24
4.75 V
10
45
VOL = 0.4 V
2.3 V to 5.5 V
3
10
VI = VCC or GND
2.3 V to 5.5 V
mA
±1
±1
µA
IIH
P port
VI = VCC
2.3 V to 5.5 V
1
µA
IIL
P port
VI = GND
2.3 V to 5.5 V
–100
µA
VI = VCC, IO = 0, I/O = inputs,
fscl = 400 kHz, No load
Operating mode
VI = VCC, IO = 0, I/O = inputs,
fscl = 100 kHz, No load
ICC
VI = GND, IO = 0, I/O = inputs,
fscl = 0 kHz, No load
Standby mode
VI = VCC, IO = 0, I/O = inputs,
fscl = 0 kHz, No load
∆ICC
CI
Cio
(1)
(2)
(3)
12
Additional current in standby
mode
SCL
SDA
P port
5.5 V
104
175
3.6 V
50
90
2.7 V
20
65
5.5 V
60
150
3.6 V
15
40
2.7 V
8
20
5.5 V
450
700
3.6 V
300
600
2.7 V
225
500
5.5 V
0.25
1
3.6 V
0.2
0.9
2.7 V
0.1
0.8
One input at VCC – 0.6 V,
Other inputs at VCC or GND
2.3 V to 5.5 V
Every LED I/O at VI = 4.3 V;
fscl = 0 kHz
5.5 V
VI = VCC or GND
VIO = VCC or GND
µA
1.5
mA
2.3 V to 5.5 V
2.3 V to 5.5 V
1
4
5
5.5
6.5
8
9.5
pF
pF
All typical values are at nominal supply voltage (2.5-V, 3.3-V, or 5-V VCC) and TA = 25°C.
The total current sourced by all I/Os must be limited to 85 mA.
Each I/O must be externally limited to a maximum of 25 mA, and the P port (P0 to P7) must be limited to a maximum current of 200 mA.
Submit Documentation Feedback
PCA9554A
REMOTE 8-BIT
AND SMBus I/O EXPANDER
WITH INTERRUPT OUTPUT AND CONFIGURATION REGISTERS
I2C
www.ti.com
SCPS127A – SEPTEMBER 2006 – REVISED FEBRUARY 2007
I2C Interface Timing Requirements
over operating free-air temperature range (unless otherwise noted) (see Figure 10)
STANDARD MODE
I2C BUS
MIN
MAX
100
FAST MODE
I2C BUS
UNIT
MIN
MAX
0
400
fscl
I2C clock frequency
0
tsch
I2C clock high time
4
0.6
µs
tscl
I2C clock low time
4.7
1.3
µs
tsp
I2C
tsds
I2C serial-data setup time
tsdh
I2C serial-data hold time
ticr
I2C input rise time
ticf
I2C
tocf
I2C output fall time
tbuf
I2C bus free time between
stop and start
4.7
1.3
µs
tsts
I2C start or repeated start
condition setup
4.7
0.6
µs
tsth
I2C start or repeated start
condition hold
4
0.6
µs
tsps
I2C
spike time
50
50
250
100
0
0
kHz
ns
ns
ns
1000
20 + 0.1Cb (1)
300
ns
300
20 + 0.1Cb
(1)
300
ns
300
20 + 0.1Cb (1)
300
ns
input fall time
10-pF to 400-pF bus
4
0.6
µs
tvd(data) Valid data time
SCL low to SDA output valid
300
50
ns
tvd(ack)
Valid data time of ACK condition
ACK signal from SCL low to
SDA (out) low
0.3
Cb
I2C bus capacitive load
(1)
stop condition setup
3.45
0.1
400
0.9
µs
400
ns
Cb = Total capacitive load of one bus in pF
Switching Characteristics
over operating free-air temperature range (unless otherwise noted) (see Figure 11 and Figure 12)
PARAMETER
STANDARD MODE
I2C BUS
FAST MODE
I2C BUS
FROM
(INPUT)
TO
(OUTPUT)
P port
INT
4
4
µs
SCL
INT
4
4
µs
200
ns
MIN
MAX
MIN
UNIT
MAX
tiv
Interrupt valid time
tir
Interrupt reset delay time
tpv
Output data valid
SCL
P7–P0
tps
Input data setup time
P port
SCL
100
100
ns
tph
Input data hold time
P port
SCL
1
1
µs
Submit Documentation Feedback
200
13
PCA9554A
REMOTE 8-BIT I2C AND SMBus I/O EXPANDER
WITH INTERRUPT OUTPUT AND CONFIGURATION REGISTERS
www.ti.com
SCPS127A – SEPTEMBER 2006 – REVISED FEBRUARY 2007
TYPICAL CHARACTERISTICS
SUPPLY CURRENT
vs
TEMPERATURE
QUIESCENT SUPPLY CURRENT
vs
TEMPERATURE
35
55
50
VCC = 5 V
30
ICC – Supply Current – nA
ICC – Supply Current – µA
45
40
f SCL = 400 kHz
I/Os unloaded
35
30
25
20
VCC = 3.3 V
15
10
VCC = 2.5 V
VCC = 5 V
25
VCC = 3.3 V
20
15
VCC = 2.5 V
10
5
5
SCL = VCC
0
-40
-15
10
35
60
0
-40
85
10
35
60
TA – Free-Air Temperature – °C
TA – Free-Air Temperature – °C
SUPPLY CURRENT
vs
SUPPLY VOLTAGE
SUPPLY CURRENT
vs
NUMBER OF I/Os HELD LOW
70
85
600
f SCL = 400 kHz
I/Os unloaded
60
VCC = 5 V
550
500
ICC – Supply Current – µA
ICC – Supply Current – µA
-15
50
40
30
20
450
400
TA = –40°C
350
300
TA = 25°C
250
200
TA = 85°C
150
100
10
50
0
0
2.3
2.7
3.1
3.5
3.9
4.3
4.7
5.1
5.5
0
VCC – Supply Voltage – V
14
1
2
3
4
5
6
Number of I/Os Held Low
Submit Documentation Feedback
7
8
PCA9554A
REMOTE 8-BIT
AND SMBus I/O EXPANDER
WITH INTERRUPT OUTPUT AND CONFIGURATION REGISTERS
I2C
www.ti.com
SCPS127A – SEPTEMBER 2006 – REVISED FEBRUARY 2007
TYPICAL CHARACTERISTICS (continued)
I/O OUTPUT LOW VOLTAGE
vs
TEMPERATURE
I/O SINK CURRENT
vs
OUTPUT LOW VOLTAGE
30
300
250
VCC = 2.5 V
VCC = 2.5 V, ISINK = 10 mA
25
ISINK – I/O Sink Current – mA
VOL – Output Low Voltage – mV
275
225
200
175
150
VCC = 5 V, ISINK = 10 mA
125
100
VCC = 2.5 V, ISINK = 1 mA
75
50
VCC = 5 V, ISINK = 1 mA
TA = –40°C
20
TA = 25°C
15
TA = 85°C
10
5
25
0
0
-40
-15
10
35
60
0.0
85
0.2
0.3
0.4
0.5
0.6
TA – Free-Air Temperature – °C
VOL – Output Low Voltage – V
I/O SINK CURRENT
vs
OUTPUT LOW VOLTAGE
I/O SINK CURRENT
vs
OUTPUT LOW VOLTAGE
0.7
60
40
VCC = 3.3 V
VCC = 5 V
55
35
50
TA = –40°C
ISINK – I/O Sink Current – mA
ISINK – I/O Sink Current – mA
0.1
30
25
TA = 25°C
20
15
TA = 85°C
10
45
TA = –40°C
40
35
TA = 25°C
30
25
TA = 85°C
20
15
10
5
5
0
0
0.0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
VOL – Output Low Voltage – V
VOL – Output Low Voltage – V
Submit Documentation Feedback
15
PCA9554A
REMOTE 8-BIT I2C AND SMBus I/O EXPANDER
WITH INTERRUPT OUTPUT AND CONFIGURATION REGISTERS
www.ti.com
SCPS127A – SEPTEMBER 2006 – REVISED FEBRUARY 2007
TYPICAL CHARACTERISTICS (continued)
I/O OUTPUT HIGH VOLTAGE
vs
TEMPERATURE
I/O SOURCE CURRENT
vs
OUTPUT HIGH VOLTAGE
275
35
VCC = 2.5 V
VCC = 2.5 V, IOL = 10 mA
ISOURCE – I/O Source Current – mA
(V CC – V OH ) – Output High Voltage – mV
250
225
200
175
150
125
VCC = 5 V, IOL = 10 mA
100
75
VCC = 2.5 V, IOL = 1 mA
50
VCC = 5 V, IOL = 1 mA
30
TA = –40°C
25
TA = 25°C
20
15
10
TA = 85°C
5
25
0
0
-40
0.0
-15
10
35
60
0.1
0.2
0.3
0.4
0.5
0.6
0.7
85
(VCC – VOH) – Output High Voltage – V
TA – Free-Air Temperature – °C
I/O SOURCE CURRENT
vs
OUTPUT HIGH VOLTAGE
I/O SOURCE CURRENT
vs
OUTPUT HIGH VOLTAGE
75
70
50
ISOURCE – I/O Source Current – mA
45
40
ISOURCE – I/O Source Current – mA
VCC = 3.3 V
TA = –40°C
35
TA = 25°C
30
25
20
TA = 85°C
15
10
5
VCC = 5 V
65
60
55
50
TA = –40°C
45
40
35
30
TA = 25°C
TA = 85°C
25
20
15
10
5
0
0
0.0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.0
(VCC – VOH) – Output High Voltage – V
16
Submit Documentation Feedback
0.1
0.2
0.3
0.4
0.5
0.6
(VCC – VOH) – Output High Voltage – V
0.7
PCA9554A
REMOTE 8-BIT
AND SMBus I/O EXPANDER
WITH INTERRUPT OUTPUT AND CONFIGURATION REGISTERS
I2C
www.ti.com
SCPS127A – SEPTEMBER 2006 – REVISED FEBRUARY 2007
TYPICAL CHARACTERISTICS (continued)
OUTPUT HIGH VOLTAGE
vs
SUPPLY VOLTAGE
6
TA = 25°C
VOH – Output High Voltage – V
5
4
IOH = –8 mA
3
IOH = –10 mA
2
1
0
2.3
2.7
3.1
3.5
3.9
4.3
4.7
5.1
5.5
VCC – Supply Voltage – V
Submit Documentation Feedback
17
PCA9554A
REMOTE 8-BIT I2C AND SMBus I/O EXPANDER
WITH INTERRUPT OUTPUT AND CONFIGURATION REGISTERS
www.ti.com
SCPS127A – SEPTEMBER 2006 – REVISED FEBRUARY 2007
PARAMETER MEASUREMENT INFORMATION
VCC
RL = 1 kΩ
SDA
DUT
CL = 50 pF
(see Note A)
SDA LOAD CONFIGURATION
Three Bytes for Complete
Device Programming
Stop
Condition
(P)
Start
Address
Address
Condition
Bit 7
Bit 6
(S)
(MSB)
Address
Bit 1
tscl
R/W
Bit 0
(LSB)
ACK
(A)
Data
Bit 07
(MSB)
Data
Bit 10
(LSB)
Stop
Condition
(P)
tsch
0.7 × VCC
SCL
0.3 × VCC
ticr
tsts
tPHL
ticf
tbuf
tPLH
tsp
0.7 × VCC
SDA
0.3 × VCC
ticf
ticr
tsth
tsdh
tsds
tsps
Repeat
Start
Condition
Start or
Repeat
Start
Condition
Stop
Condition
VOLTAGE WAVEFORMS
BYTE
DESCRIPTION
1
I2C address
2, 3
P-port data
A.
CL includes probe and jig capacitance.
B.
All inputs are supplied by generators having the following characteristics: PRR ≤ 10 MHz, ZO = 50 Ω, tr/tf ≤ 30 ns.
C.
All parameters and waveforms are not applicable to all devices.
Figure 10. I2C Interface Load Circuit and Voltage Waveforms
18
Submit Documentation Feedback
PCA9554A
REMOTE 8-BIT
AND SMBus I/O EXPANDER
WITH INTERRUPT OUTPUT AND CONFIGURATION REGISTERS
I2C
www.ti.com
SCPS127A – SEPTEMBER 2006 – REVISED FEBRUARY 2007
PARAMETER MEASUREMENT INFORMATION (continued)
VCC
RL = 4.7 kΩ
INT
DUT
CL = 100 pF
(see Note A)
INTERRUPT LOAD CONFIGURATION
ACK
From Slave
Start
Condition
8 Bits
(One Data Bytes)
From Port
R/W
Slave Address
S
0
1
1
1 A2 A1 A0 1
A
1
2
3
4
A
5
6
7
8
Data 1
ACK
From Slave
Data From Port
A
Data 2
1
P
A
tir
tir
B
B
INT
A
tiv
tsps
A
Data
Into
Port
Address
Data 1
0.7 × VCC
INT
0.3 × VCC
SCL
Data 2
0.7 × VCC
R/W
tiv
A
0.3 × VCC
tir
0.7 × VCC
Pn
0.7 × VCC
1.5 V
0.3 × VCC
INT
0.3 × VCC
View A−A
View B−B
A.
CL includes probe and jig capacitance.
B.
All inputs are supplied by generators having the following characteristics: PRR ≤ 10 MHz, ZO = 50 Ω, tr/tf ≤ 30 ns.
C.
All parameters and waveforms are not applicable to all devices.
Figure 11. Interrupt Load Circuit and Voltage Waveforms
Submit Documentation Feedback
19
PCA9554A
REMOTE 8-BIT I2C AND SMBus I/O EXPANDER
WITH INTERRUPT OUTPUT AND CONFIGURATION REGISTERS
www.ti.com
SCPS127A – SEPTEMBER 2006 – REVISED FEBRUARY 2007
PARAMETER MEASUREMENT INFORMATION (continued)
Pn
500 W
DUT
CL = 50 pF
(see Note A)
2 × VCC
500 W
P-PORT LOAD CONFIGURATION
SCL
0.7 × VCC
P0
A
P7
0.3 × VCC
Slave
ACK
ÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎ
SDA
Pn
tpv
(see Note B)
Unstable
Data
Last Stable Bit
WRITE MODE (R/W = 0)
SCL
0.7 × VCC
P0
A
tps
P7
0.3 × VCC
tph
0.7 × VCC
1.5 V
0.3 × VCC
Pn
READ MODE (R/W = 1)
A.
CL includes probe and jig capacitance.
B.
tpv is measured from 0.7 × VCC on SCL to 50% I/O pin output.
C.
All inputs are supplied by generators having the following characteristics: PRR ≤ 10 MHz, ZO = 50 Ω, tr/tf ≤ 30 ns.
D.
The outputs are measured one at a time, with one transition per measurement.
E.
All parameters and waveforms are not applicable to all devices.
Figure 12. P-Port Load Circuit and Voltage Waveforms
20
Submit Documentation Feedback
PCA9554A
REMOTE 8-BIT
AND SMBus I/O EXPANDER
WITH INTERRUPT OUTPUT AND CONFIGURATION REGISTERS
I2C
www.ti.com
SCPS127A – SEPTEMBER 2006 – REVISED FEBRUARY 2007
PARAMETER MEASUREMENT INFORMATION (continued)
VCC
RL = 1 kΩ
DUT
500 W
Pn
SDA
2 × VCC
DUT
CL = 50 pF
(see Note A)
CL = 50 pF
(see Note A)
500 W
P-PORT LOAD CONFIGURATION
SDA LOAD CONFIGURATION
Start
SCL
ACK or Read Cycle
SDA
0.3 y VCC
tRESET
RESET
VCC/2
tREC
tw
Pn
VCC/2
tRESET
A.
CL includes probe and jig capacitance.
B.
All inputs are supplied by generators having the following characteristics: PRR ≤ 10 MHz, ZO = 50 Ω, tr/tf ≤ 30 ns.
C.
All parameters and waveforms are not applicable to all devices.
Figure 13. Reset Load Circuits and Voltage Waveforms
Submit Documentation Feedback
21
PCA9554A
REMOTE 8-BIT I2C AND SMBus I/O EXPANDER
WITH INTERRUPT OUTPUT AND CONFIGURATION REGISTERS
www.ti.com
SCPS127A – SEPTEMBER 2006 – REVISED FEBRUARY 2007
APPLICATION INFORMATION
Figure 14 shows an application in which the PCA9554A can be used.
VCC
(5 V)
10 kW
VCC
Master
Controller
10 kW
2 kW
10 kW
VCC
SDA
SDA
SCL
SCL
INT
INT
P0
Subsystem 1
(e.g., Temperature Sensor)
P1
INT
P2
RESET
P3
GND
Subsystem 2
(e.g., Counter)
PCA9554A
P4
A
P5
A2
Controlled Device
(e.g., CBT Device)
P6
ENABLE
A1
P7
B
A0
GND
ALARM
Subsystem 3
(e.g., Alarm System)
VCC
A.
Device address is configured as 0111000 for this example.
B.
P0, P2, and P3 are configured as outputs.
C.
P1, P4, and P5 are configured as inputs.
D.
P6 and P7 are not used and have internal 100-kΩ pullup resistors to protect them from floating.
Figure 14. Typical Application
22
Submit Documentation Feedback
PCA9554A
REMOTE 8-BIT
AND SMBus I/O EXPANDER
WITH INTERRUPT OUTPUT AND CONFIGURATION REGISTERS
I2C
www.ti.com
SCPS127A – SEPTEMBER 2006 – REVISED FEBRUARY 2007
APPLICATION INFORMATION (continued)
Minimizing ICC When I/Os Control LEDs
When the I/Os are used to control LEDs, normally they are connected to VCC through a resistor as shown in
Figure 14. The LED acts as a diode so when the LED is off the I/O VIN is about 1.2 V less than VCC. ∆ICC in
Electrical Characteristics shows how ICC increases as VIN becomes lower than VCC.
For battery powered applications, it is essential that the voltage of I/O pins is greater than or equal to VCC when
the LED is off to minimize current consumption. Figure 15 shows a high value resistor in parallel with the LED.
Figure 16 shows VCC less than the LED supply voltage by at least 1.2 V. Both of these methods maintain the I/O
VIN at or above VCC and prevents additional supply current consumption when the LED is off.
VCC
LED
100 kW
VCC
LEDx
Figure 15. High-Value Resistor in Parallel With LED
3.3 V
VCC
5V
LED
LEDx
Figure 16. Device Supplied by a Lower Voltage
Submit Documentation Feedback
23
PACKAGE OPTION ADDENDUM
www.ti.com
19-Dec-2006
PACKAGING INFORMATION
Orderable Device
Status (1)
Package
Type
Package
Drawing
Pins Package Eco Plan (2)
Qty
PCA9554ADB
ACTIVE
SSOP
DB
16
80
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
PCA9554ADBG4
ACTIVE
SSOP
DB
16
80
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
PCA9554ADBQR
PREVIEW
SSOP/
QSOP
DBQ
16
2500
TBD
Call TI
PCA9554ADBR
ACTIVE
SSOP
DB
16
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
PCA9554ADBRG4
ACTIVE
SSOP
DB
16
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
Call TI
MSL Peak Temp (3)
Call TI
PCA9554ADGV
PREVIEW
TVSOP
DGV
16
125
PCA9554ADGVR
ACTIVE
TVSOP
DGV
16
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
PCA9554ADGVRG4
ACTIVE
TVSOP
DGV
16
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
PCA9554ADW
ACTIVE
SOIC
DW
16
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
PCA9554ADWR
ACTIVE
SOIC
DW
16
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
PCA9554APW
ACTIVE
TSSOP
PW
16
90
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
PCA9554APWG4
ACTIVE
TSSOP
PW
16
90
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
PCA9554APWR
ACTIVE
TSSOP
PW
16
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
PCA9554APWRG4
ACTIVE
TSSOP
PW
16
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
PCA9554ARGTR
PREVIEW
QFN
RGT
16
3000
TBD
Call TI
Call TI
PCA9554ARGVR
PREVIEW
QFN
RGV
16
2500
TBD
Call TI
Call TI
40
TBD
Lead/Ball Finish
Call TI
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check
http://www.ti.com/productcontent for the latest availability information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and
package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS
compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame
retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder
temperature.
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
19-Dec-2006
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.
Addendum-Page 2
MECHANICAL DATA
MPDS006C – FEBRUARY 1996 – REVISED AUGUST 2000
DGV (R-PDSO-G**)
PLASTIC SMALL-OUTLINE
24 PINS SHOWN
0,40
0,23
0,13
24
13
0,07 M
0,16 NOM
4,50
4,30
6,60
6,20
Gage Plane
0,25
0°–8°
1
0,75
0,50
12
A
Seating Plane
0,15
0,05
1,20 MAX
PINS **
0,08
14
16
20
24
38
48
56
A MAX
3,70
3,70
5,10
5,10
7,90
9,80
11,40
A MIN
3,50
3,50
4,90
4,90
7,70
9,60
11,20
DIM
4073251/E 08/00
NOTES: A.
B.
C.
D.
All linear dimensions are in millimeters.
This drawing is subject to change without notice.
Body dimensions do not include mold flash or protrusion, not to exceed 0,15 per side.
Falls within JEDEC: 24/48 Pins – MO-153
14/16/20/56 Pins – MO-194
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
MECHANICAL DATA
MSSO002E – JANUARY 1995 – REVISED DECEMBER 2001
DB (R-PDSO-G**)
PLASTIC SMALL-OUTLINE
28 PINS SHOWN
0,38
0,22
0,65
28
0,15 M
15
0,25
0,09
8,20
7,40
5,60
5,00
Gage Plane
1
14
0,25
A
0°–ā8°
0,95
0,55
Seating Plane
2,00 MAX
0,10
0,05 MIN
PINS **
14
16
20
24
28
30
38
A MAX
6,50
6,50
7,50
8,50
10,50
10,50
12,90
A MIN
5,90
5,90
6,90
7,90
9,90
9,90
12,30
DIM
4040065 /E 12/01
NOTES: A.
B.
C.
D.
All linear dimensions are in millimeters.
This drawing is subject to change without notice.
Body dimensions do not include mold flash or protrusion not to exceed 0,15.
Falls within JEDEC MO-150
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
MECHANICAL DATA
MTSS001C – JANUARY 1995 – REVISED FEBRUARY 1999
PW (R-PDSO-G**)
PLASTIC SMALL-OUTLINE PACKAGE
14 PINS SHOWN
0,30
0,19
0,65
14
0,10 M
8
0,15 NOM
4,50
4,30
6,60
6,20
Gage Plane
0,25
1
7
0°– 8°
A
0,75
0,50
Seating Plane
0,15
0,05
1,20 MAX
PINS **
0,10
8
14
16
20
24
28
A MAX
3,10
5,10
5,10
6,60
7,90
9,80
A MIN
2,90
4,90
4,90
6,40
7,70
9,60
DIM
4040064/F 01/97
NOTES: A.
B.
C.
D.
All linear dimensions are in millimeters.
This drawing is subject to change without notice.
Body dimensions do not include mold flash or protrusion not to exceed 0,15.
Falls within JEDEC MO-153
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications,
enhancements, improvements, and other changes to its products and services at any time and to
discontinue any product or service without notice. Customers should obtain the latest relevant information
before placing orders and should verify that such information is current and complete. All products are sold
subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in
accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent
TI deems necessary to support this warranty. Except where mandated by government requirements, testing
of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible
for their products and applications using TI components. To minimize the risks associated with customer
products and applications, customers should provide adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent
right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine,
or process in which TI products or services are used. Information published by TI regarding third-party
products or services does not constitute a license from TI to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or
other intellectual property of the third party, or a license from TI under the patents or other intellectual
property of TI.
Reproduction of information in TI data books or data sheets is permissible only if reproduction is without
alteration and is accompanied by all associated warranties, conditions, limitations, and notices.
Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not
responsible or liable for such altered documentation.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for
that product or service voids all express and any implied warranties for the associated TI product or service
and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements.
Following are URLs where you can obtain information on other Texas Instruments products and application
solutions:
Products
Applications
Amplifiers
amplifier.ti.com
Audio
www.ti.com/audio
Data Converters
dataconverter.ti.com
Automotive
www.ti.com/automotive
DSP
dsp.ti.com
Broadband
www.ti.com/broadband
Interface
interface.ti.com
Digital Control
www.ti.com/digitalcontrol
Logic
logic.ti.com
Military
www.ti.com/military
Power Mgmt
power.ti.com
Optical Networking
www.ti.com/opticalnetwork
Microcontrollers
microcontroller.ti.com
Security
www.ti.com/security
Low Power Wireless
www.ti.com/lpw
Telephony
www.ti.com/telephony
Mailing Address:
Video & Imaging
www.ti.com/video
Wireless
www.ti.com/wireless
Texas Instruments
Post Office Box 655303 Dallas, Texas 75265
Copyright © 2007, Texas Instruments Incorporated