Product Folder Sample & Buy Support & Community Tools & Software Technical Documents Reference Design TCA6408A SCPS192D – APRIL 2009 – REVISED JULY 2015 TCA6408A Low-Voltage 8-Bit I2C and SMBus I/O Expander With Interrupt Output, Reset, and Configuration Registers 1 Features • • 1 • • • • • • • • • • • • • • • • • 2 Applications 2 I C to Parallel Port Expander Operating Power-Supply Voltage Range of 1.65 V to 5.5 V Allows Bidirectional Voltage-Level Translation and GPIO Expansion Between 1.8-V, 2.5-V, 3.3-V, and 5-V I2C Bus and P-Ports Low Standby Current Consumption of 1 μA 5-V Tolerant I/O Ports 400-kHz Fast I2C Bus Hardware Address Pin Allows Two TCA6408A Devices on the Same I2C/SMBus Bus Active-Low Reset (RESET) Input Open-Drain Active-Low Interrupt (INT) Output Input/Output Configuration Register Polarity Inversion Register Internal Power-On Reset Power Up With All Channels Configured as Inputs No Glitch On Power Up Noise Filter on SCL/SDA Inputs Latched Outputs With High-Current Drive Maximum Capability for Directly Driving LEDs Latch-Up Performance Exceeds 100 mA Per JESD 78, Class II Schmitt-Trigger Action Allows Slow Input Transition and Better Switching Noise Immunity at the SCL and SDA Inputs ESD Protection Exceeds JESD 22 – 2000-V Human Body Model (A114-A) – 1000-V Charged-Device Model (C101) • • • • • • Servers Routers (Telecom Switching Equipment) Personal Computers Personal Electronics (Gaming Consoles) Industrial Automation Products With GPIO-Limited Processors 3 Description The TCA6408A is a 16-pin device that provides 8-bits of general purpose parallel input/output (I/O) expansion for the two-line bidirectional I2C bus (or SMBus) protocol. This device can operate with a power supply voltage ranging from 1.65 V to 5.5 V on both the I2C bus side (VCCI) and on the P-port side (VCCP). This allows the TCA6408A to interface with next-generation microprocessors and microcontrollers on the SDA/SCL side, where supply levels are dropping down to conserve power. In contrast to the dropping power supplies of microprocessors and microcontrollers, some PCB components such as LEDs remain at a 5-V power supply. The device supports both 100-kHz (Standard-mode) and 400-kHz (Fast-mode) clock frequencies. I/O expanders such as the TCA6408A provide a simple solution when additional I/Os are needed for switches, sensors, push-buttons, LEDs, fans, and so forth. Device Information(1) PART NUMBER TCA6408A PACKAGE BODY SIZE (NOM) TSSOP (16) 5.00 mm × 4.40 mm VQFN (16) 3.00 mm × 3.00 mm UQFN (16) 2.60 mm × 1.80 mm (1) For all available packages, see the orderable addendum at the end of the datasheet. Simplified Schematic VCCI I2C or SMBus Master (e.g. Processor) VCCP SDA P0 Peripheral Devices SCL P1 INT P2 x RESET P3 x P4 x x TCA6408A RESET, EN or Control Inputs INT or status outputs LEDs Keypad P5 P6 P7 ADDR GND 1 An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications, intellectual property matters and other important disclaimers. PRODUCTION DATA. TCA6408A SCPS192D – APRIL 2009 – REVISED JULY 2015 www.ti.com Table of Contents 1 2 3 4 5 6 7 8 Features .................................................................. Applications ........................................................... Description ............................................................. Revision History..................................................... Pin Configuration and Functions ......................... Specifications......................................................... 1 1 1 2 3 4 6.1 6.2 6.3 6.4 6.5 6.6 6.7 6.8 6.9 4 4 4 5 6 7 7 7 8 Absolute Maximum Ratings ..................................... ESD Ratings.............................................................. Recommended Operating Conditions....................... Thermal Information .................................................. Electrical Characteristics........................................... I2C Interface Timing Requirements........................... Reset Timing Requirements ..................................... Switching Characteristics .......................................... Typical Characteristics .............................................. Parameter Measurement Information ................ 11 Detailed Description ............................................ 15 8.1 Overview ................................................................. 15 8.2 Functional Block Diagrams ..................................... 16 8.3 8.4 8.5 8.6 9 Feature Description................................................. Device Functional Modes........................................ Programming .......................................................... Register Map........................................................... 18 19 19 23 Application and Implementation ........................ 25 9.1 Application Information............................................ 25 9.2 Typical Application .................................................. 26 10 Power Supply Recommendations ..................... 29 10.1 Power-On Reset Requirements ........................... 29 11 Layout................................................................... 31 11.1 Layout Guidelines ................................................. 31 11.2 Layout Example .................................................... 31 12 Device and Documentation Support ................. 32 12.1 12.2 12.3 12.4 Community Resources.......................................... Trademarks ........................................................... Electrostatic Discharge Caution ............................ Glossary ................................................................ 32 32 32 32 13 Mechanical, Packaging, and Orderable Information ........................................................... 32 4 Revision History NOTE: Page numbers for previous revisions may differ from page numbers in the current version. Changes from Revision C (July 2009) to Revision D Page • Added Pin Configuration and Functions section, ESD Ratings table, Feature Description section, Device Functional Modes, Application and Implementation section, Power Supply Recommendations section, Layout section, Device and Documentation Support section, and Mechanical, Packaging, and Orderable Information section .............................. 1 • VIH - Split SCL, SDA and RESET to different rows in the Recommended Operating Conditions table. Max value of SCL, SDA changed From: 5.5 V To: VCCI............................................................................................................................... 4 2 Submit Documentation Feedback Copyright © 2009–2015, Texas Instruments Incorporated Product Folder Links: TCA6408A TCA6408A www.ti.com SCPS192D – APRIL 2009 – REVISED JULY 2015 5 Pin Configuration and Functions 9 4 13 14 ADDR VCCI VCCP SDA 11 3 10 4 9 SCL INT P7 P6 8 12 7 10 15 9 16 8 11 1 2 5 10 3 Exposed Center Pad RESET P0 P1 P2 SCL INT P7 P6 6 7 2 12 P3 GND P4 P5 11 13 6 14 12 1 8 5 RESET P0 P1 P2 7 13 GND P4 P5 14 4 15 3 VCCP SDA SCL INT P7 P6 P5 P4 16 15 5 16 2 6 1 RSV Package 16-Pin UQFN Top View P3 VCCI ADDR RESET P0 P1 P2 P3 GND RGT Package 16-Pin VQFN Top View ADDR VCCI VCCP SDA PW Package 16-Pin TSSOP Top View If used, the exposed center pad must be connected as a secondary ground or left electrically open. Pin Functions PIN NAME DESCRIPTION TSSOP UQFN, VQFN ADDR 2 16 Address input. Connect directly to VCCP or ground. GND 8 6 Ground INT 13 11 Interrupt output. Connect to VCCI through a pull-up resistor. P0 4 2 P-port input/output (push-pull design structure). At power on, P0 is configured as an input. P1 5 3 P-port input/output (push-pull design structure). At power on, P1 is configured as an input. P2 6 4 P-port input/output (push-pull design structure). At power on, P2 is configured as an input. P3 7 5 P-port input/output (push-pull design structure). At power on, P3 is configured as an input. P4 9 7 P-port input/output (push-pull design structure). At power on, P4 is configured as an input. P5 10 8 P-port input/output (push-pull design structure). At power on, P5 is configured as an input. P6 11 9 P-port input/output (push-pull design structure). At power on, P6 is configured as an input. P7 12 10 P-port input/output (push-pull design structure). At power on, P7 is configured as an input. RESET 3 1 Active-low reset input. Connect to VCCI through a pull-up resistor, if no active connection is used. SCL 14 12 Serial clock bus. Connect to VCCI through a pull-up resistor. SDA 15 13 Serial data bus. Connect to VCCI through a pull-up resistor. VCCI 1 15 Supply voltage of I2C bus. Connect directly to the VCC of the external I2C master. Provides voltage level translation. VCCP 16 14 Supply voltage of TCA6408A for P-ports Submit Documentation Feedback Copyright © 2009–2015, Texas Instruments Incorporated Product Folder Links: TCA6408A 3 TCA6408A SCPS192D – APRIL 2009 – REVISED JULY 2015 www.ti.com 6 Specifications 6.1 Absolute Maximum Ratings over operating free-air temperature range (unless otherwise noted) (see (1) ) MIN MAX UNIT VCCI Supply voltage for I2C pins –0.5 6.5 V VCCP Supply voltage for P-ports –0.5 6.5 V VI Input voltage (2) –0.5 6.5 V VO Output voltage (2) –0.5 6.5 V IIK Input clamp current ADDR, RESET, SCL VI < 0 ±20 mA IOK Output clamp current INT VO < 0 ±20 mA P-port VO < 0 or VO > VCCP ±20 SDA VO < 0 or VO > VCCI ±20 Continuous output low current P-port VO = 0 to VCCP 50 Continuous output low current SDA, INT VO = 0 to VCCI 25 Continuous output high current P-port VO = 0 to VCCP 50 IIOK Input/output clamp current IOL IOH ICC Tstg (1) (2) mA mA Continuous current through GND 200 Continuous current through VCCP 160 Continuous current through VCCI 10 Storage temperature –65 mA 150 mA °C Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under Recommended Operating Conditions. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. The input negative-voltage and output voltage ratings may be exceeded if the input and output current ratings are observed. 6.2 ESD Ratings VALUE V(ESD) (1) (2) Electrostatic discharge Human body model (HBM), per ANSI/ESDA/JEDEC JS-001 (1) ±2000 Charged-device model (CDM), per JEDEC specification JESD22C101 (2) ±1000 UNIT V JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process. JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process. 6.3 Recommended Operating Conditions MIN MAX VCCI Supply voltage for I2C pins 1.65 5.5 VCCP Supply voltage for P-ports 1.65 5.5 SCL, SDA 0.7 × VCCI VCCI VIH High-level input voltage RESET 0.7 × VCCI 5.5 ADDR, P7–P0 0.7 × VCCP 5.5 SCL, SDA, RESET –0.5 0.3 × VCCI ADDR, P7–P0 –0.5 0.3 × VCCP VIL Low-level input voltage IOH High-level output current P7–P0 IOL Low-level output current P7–P0 TA Operating free-air temperature 4 –40 Submit Documentation Feedback UNIT V V V 10 mA 25 mA 85 °C Copyright © 2009–2015, Texas Instruments Incorporated Product Folder Links: TCA6408A TCA6408A www.ti.com SCPS192D – APRIL 2009 – REVISED JULY 2015 6.4 Thermal Information TCA6408A THERMAL METRIC (1) PW (TSSOP) RGT (VQFN) RSV (UQFN) 16 PINS 16 PINS 16 PINS UNIT RθJA Junction-to-ambient thermal resistance 122 65.5 127.7 °C/W RθJC(top) Junction-to-case (top) thermal resistance 56.4 92.1 62.3 °C/W RθJB Junction-to-board thermal resistance 67.1 40.0 48.4 °C/W ψJT Junction-to-top characterization parameter 10.8 6.9 2.5 °C/W ψJB Junction-to-board characterization parameter 66.5 21.3 48.6 °C/W (1) For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application report, SPRA953. Submit Documentation Feedback Copyright © 2009–2015, Texas Instruments Incorporated Product Folder Links: TCA6408A 5 TCA6408A SCPS192D – APRIL 2009 – REVISED JULY 2015 www.ti.com 6.5 Electrical Characteristics over recommended operating free-air temperature range, VCCI = 1.65 V to 5.5 V (unless otherwise noted) PARAMETER TEST CONDITIONS VCCP VIK Input diode clamp voltage II = –18 mA 1.65 V to 5.5 V VPOR Power-on reset voltage (2) VI = VCCP or GND, IO = 0 1.65 V to 5.5 V IOH = –8 mA P-port high-level output voltage VOH IOH = –10 mA IOL = 8 mA P-port low-level output voltage VOL IOL = 10 mA MIN TYP (1) –1.2 1.65 V 1.2 2.3 V 1.8 3V 2.6 4.5 V 4.1 1.65 V 1.1 2.3 V 1.7 3V 2.5 4.5 V 4.0 IOL VOL = 0.4 V INT SCL, SDA, RESET VI = VCCI or GND ADDR VI = VCCP or GND IIH P-port VI = VCCP IIL P-port VI = GND II Operating mode ICC (ICCI + ICCP) Standby mode V 0.45 2.3 V 0.25 3V 0.25 4.5 V 0.2 1.65 V 0.6 2.3 V 0.3 3V 0.25 3 mA 15 ±0.1 1.65 V to 5.5 V ±0.1 1.65 V to 5.5 V μA 1 μA 1 μA VI on SCL, SDA and RESET = VCCI or GND, VI on P-Port and ADDR = VCCP or GND, IO = 0, I/O = inputs, fSCL = 0 SCL, SDA, RESET One input at VCCI – 0.6 V, Other inputs at VCCI or GND 1.65 V to 5.5 V 25 μA P-port, ADDR One input at VCCP – 0.6 V, Other inputs at VCCP or GND 1.65 V to 5.5 V 80 μA 1.65 V to 5.5 V 6 7 pF 7 8 7.5 8.5 SCL VI = VCCI or GND SDA VIO = VCCI or GND P-port VIO = VCCP or GND 6 0.2 3 SCL, SDA, P-port, ADDR, RESET Ci (1) (2) V VI on SDA and RESET= VCCI or GND, VI on P-port and ADDR = VCCP or GND, IO = 0, I/O = inputs, fSCL = 400 kHz ΔICCP Cio V SDA, P-port, ADDR, RESET Additional current in standby mode ΔICCI 1.4 1.65 V 1.65 V to 5.5 V UNIT V 1 4.5 V SDA MAX 3.6 V to 5.5 V 10 20 2.3 V to 3.6 V 6.5 15 1.65 V to 2.3 V 4 9 3.6 V to 5.5 V 1.5 7 2.3 V to 3.6 V 1 3.2 1.65 V to 2.3 V 0.5 1.7 1.65 V to 5.5 V μA pF All typical values are at nominal supply voltage (1.8-V, 2.5-V, 3.3-V, or 5-V VCC) and TA = 25°C. When power (from 0 V) is applied to VCCP, an internal power-on reset holds the TCA6408A in a reset condition until VCCP has reached VPOR. At that time, the reset condition is released, and the TCA6408A registers and I2C/SMBus state machine initialize to their default states. After that, VCCP must be lowered to below 0.2 V and back up to the operating voltage for a power-reset cycle. Submit Documentation Feedback Copyright © 2009–2015, Texas Instruments Incorporated Product Folder Links: TCA6408A TCA6408A www.ti.com SCPS192D – APRIL 2009 – REVISED JULY 2015 6.6 I2C Interface Timing Requirements over recommended operating free-air temperature range (unless otherwise noted) (see Figure 18) STANDARD MODE I2C BUS MIN MAX 100 fscl I2C clock frequency 0 tsch I2C clock high time 4 2 tscl I C clock low time tsp I2C spike time tsds I2C serial data setup time FAST MODE I2C BUS MAX 0 400 kHz μs 0.6 4.7 μs 1.3 0 50 0 250 2 UNIT MIN 50 ns 100 0 ns tsdh I C serial data hold time ticr I2C input rise time 1000 20 + 0.1Cb 300 ticf I2C input fall time 300 20 + 0.1Cb 300 ns tocf I2C output fall time, 10-pF to 400-pF bus 300 20 + 0.1Cb 300 μs tbuf I2C bus free time between Stop and Start 4.7 1.3 μs tsts I2C Start or repeater Start condition setup time 4.7 0.6 μs tsth I2C Start or repeater Start condition hold time 4 0.6 μs 2 0 4 ns ns μs tsps I C Stop condition setup time tvd(data) Valid data time, SCL low to SDA output valid 1 0.6 1 μs tvd(ack) Valid data time of ACK condition, ACK signal from SCL low to SDA (out) low 1 1 μs 6.7 Reset Timing Requirements over recommended operating free-air temperature range (unless otherwise noted) (see Figure 21) STANDARD MODE I2C BUS MIN FAST MODE I2C BUS MAX MIN UNIT MAX tW Reset pulse duration 4 4 ns tREC Reset recovery time 0 0 ns tRESET Time to reset 600 600 ns 6.8 Switching Characteristics over recommended operating free-air temperature range, CL ≤ 100 pF (unless otherwise noted) (see Figure 18) PARAMETER STANDARD MODE I2C BUS FAST MODE I2C BUS FROM (INPUT) TO (OUTPUT) P-Port INT 4 4 μs SCL INT 4 4 μs 400 ns MIN MAX MIN UNIT MAX tiv Interrupt valid time tir Interrupt reset delay time tpv Output data valid SCL P7–P0 tps Input data setup time P-Port SCL 0 0 ns tph Input data hold time P-Port SCL 300 300 ns 400 Submit Documentation Feedback Copyright © 2009–2015, Texas Instruments Incorporated Product Folder Links: TCA6408A 7 TCA6408A SCPS192D – APRIL 2009 – REVISED JULY 2015 www.ti.com 6.9 Typical Characteristics TA = 25°C (unless otherwise noted) 22 2000 Supply Current, ICC (µA) 18 Supply Current, ICC (nA) VCC = 5.5 V 20 VCC = 5 V 16 14 12 10 VCC = 3.3 V 8 VCC = 2.5 V 6 4 VCC = 1.8 V 2 VCC = 1.65 V 0 -40 -15 10 35 1800 VCC = 5.5 V 1600 VCC = 5 V 1400 1200 VCC = 3.3 V 1000 VCC = 2.5 V 800 600 VCC = 1.8 V 400 VCC = 1.65 V 200 60 0 –40 85 –15 10 35 60 85 Temperature, TA (°C) Temperature, TA (°C) Figure 1. Supply Current vs Temperature Figure 2. Standby Supply Current vs Temperature 22 30 VCC = 1.65 V Sink Current, ISINK (mA) Supply Current, ICC (µA) 20 18 16 14 12 10 8 6 4 25 TA = –40°C 20 TA = 25°C 15 10 TA = 85°C 5 2 0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 0.0 0.1 0.2 0.3 0.5 0.4 0.6 Supply Voltage, VCC (V) Output Low Voltage, VOL (V) Figure 3. Supply Current vs Supply Voltage Figure 4. I/O Sink Current vs Output Low Voltage 50 VCC = 1.8 V VCC = 2.5 V TA = –40°C 30 Sink Current, ISINK (mA) Sink Current, ISINK (mA) 35 25 20 TA = 25°C 15 10 TA = 85°C 5 0 0.0 8 0 0.1 0.2 0.3 0.4 0.5 40 TA = 25°C 30 20 TA = 85°C 10 0 0.0 0.6 TA = –40°C 0.1 0.2 0.3 0.4 0.5 0.6 Output Low Voltage, VOL (V) Output Low Voltage, VOL (V) Figure 5. I/O Sink Current vs Output Low Voltage Figure 6. I/O Sink Current vs Output Low Voltage Submit Documentation Feedback Copyright © 2009–2015, Texas Instruments Incorporated Product Folder Links: TCA6408A TCA6408A www.ti.com SCPS192D – APRIL 2009 – REVISED JULY 2015 Typical Characteristics (continued) TA = 25°C (unless otherwise noted) 60 70 VCC = 5.0 V Sink Current, ISINK (mA) Sink Current, ISINK (mA) VCC = 3.3 V TA = –40°C 50 40 TA = 25°C 30 20 TA = 85°C 10 0 0.0 0.1 0.2 0.3 0.5 0.4 60 50 40 TA = 25°C 30 20 TA = 85°C 10 0 0.0 0.6 TA = –40°C 0.1 0.2 0.3 0.4 0.5 0.6 Output Low Voltage, VOL (V) Output Low Voltage, VOL (V) Figure 7. I/O Sink Current vs Output Low Voltage Figure 8. I/O Sink Current vs Output Low Voltage 250 Sink Current, ISINK (mA) VCC = 5.5 V 60 Output Low Voltage, VOL (mV) 70 TA = –40°C 50 40 TA = 25°C 30 20 TA = 85°C 10 0 0.0 0.1 0.2 0.3 0.4 0.5 0.6 VCC = 1.8 V, ISINK = 10 mA 200 150 VCC = 5 V, ISINK = 10 mA 100 VCC = 1.8 V, ISINK = 1 mA 50 VCC = 5 V, ISINK = 1 mA 0 -40 -15 10 35 60 85 Output Low Voltage, VOL (V) Temperature, TA (°C) Figure 9. I/O Sink Current vs Output Low Voltage Figure 10. I/O Low Voltage vs Temperature 25 VCC = 1.65 V Source Current, ISOURCE (mA) Source Current, ISOURCE (mA) 20 TA = –40°C 15 TA = 25°C 10 TA = 85°C 5 0 0.0 0.1 0.2 0.3 0.4 0.5 0.6 VCC = 1.8 V TA = –40°C 20 15 TA = 25°C 10 TA = 85°C 5 0 0.0 0.1 0.2 0.3 0.4 0.5 0.6 VCCP – VOH (V) VCCP – VOH (V) Figure 11. I/O Source Current vs Output High Voltage Figure 12. I/O Source Current vs Output High Voltage Submit Documentation Feedback Copyright © 2009–2015, Texas Instruments Incorporated Product Folder Links: TCA6408A 9 TCA6408A SCPS192D – APRIL 2009 – REVISED JULY 2015 www.ti.com Typical Characteristics (continued) TA = 25°C (unless otherwise noted) 50 VCC = 2.5 V TA = –40°C 30 Source Current, ISOURCE (mA) Source Current, ISOURCE (mA) 35 25 20 TA = 25°C 15 TA = 85°C 10 5 0 0.0 0.1 0.2 0.3 0.4 0.5 VCC = 3.3 V 30 TA = 25°C 20 TA = 85°C 10 0 0.6 0.0 0.1 VCCP – VOH (V) Source Current, ISOURCE (mA) Source Current, ISOURCE (mA) 40 TA = 25°C 30 TA = 85°C 10 0 0.0 0.1 0.2 0.3 0.4 0.4 0.5 0.6 70 50 20 0.3 Figure 14. I/O Source Current vs Output High Voltage TA = –40°C VCC = 5.0 V 0.2 VCCP – VOH (V) Figure 13. I/O Source Current vs Output High Voltage 60 TA = –40°C 40 0.5 0.6 VCC = 5.5 V TA = –40°C 60 50 40 TA = 25°C 30 20 TA = 85°C 10 0 0.0 0.1 VCCP – VOH (V) 0.2 0.3 0.4 0.5 0.6 VCCP – VOH (V) Figure 15. I/O Source Current vs Output High Voltage Figure 16. I/O Source Current vs Output High Voltage 350 ISOURCE = –10 mA VCC – VOH (mV) 300 250 VCC = 1.8 V 200 VCC = 5 V 150 100 50 0 -40 -15 10 35 60 85 Temperature, TA (°C) Figure 17. I/O High Voltage vs Temperature 10 Submit Documentation Feedback Copyright © 2009–2015, Texas Instruments Incorporated Product Folder Links: TCA6408A TCA6408A www.ti.com SCPS192D – APRIL 2009 – REVISED JULY 2015 7 Parameter Measurement Information VCCI RL = 1 kW SDA DUT CL = 50 pF (see Note A) SDA LOAD CONFIGURATION Two Bytes for READ Input Port Register (see Figure 9) Address Bit 7 (MSB) Stop Start Condition Condition (P) (S) tscl Address Bit 1 R/W Bit 0 (LSB) Data Bit 7 (MSB) ACK (A) Data Bit 0 (LSB) Stop Condition (P) tsch 0.7 ´ VCCI SCL 0.3 ´ VCCI ticr ticf tbuf tvd tsp tocf tvd tsts tsps SDA 0.7 ´ VCCI 0.3 ´ VCCI ticr ticf tsth tsdh tsds tvd(ack) Repeat Start Condition Stop Condition VOLTAGE WAVEFORMS BYTE DESCRIPTION 2 1 I C address 2 Input register port data A. CL includes probe and jig capacitance. tocf is measured with CL of 10 pF or 400 pF. B. All inputs are supplied by generators having the following characteristics: PRR ≤ 10 MHz, ZO = 50 Ω, tr/tf ≤ 30 ns. C. All parameters and waveforms are not applicable to all devices. Figure 18. I2C Interface Load Circuit and Voltage Waveforms Submit Documentation Feedback Copyright © 2009–2015, Texas Instruments Incorporated Product Folder Links: TCA6408A 11 TCA6408A SCPS192D – APRIL 2009 – REVISED JULY 2015 www.ti.com Parameter Measurement Information (continued) VCCI RL = 4.7 kW INT DUT CL = 100 pF (see Note A) INTERRUPT LOAD CONFIGURATION ACK From Slave Start Condition 8 Bits (One Data Byte) From Port R/W Slave Address S 0 1 0 0 0 0 AD DR 1 A 1 2 3 4 5 6 7 8 A Data 1 ACK From Slave Data From Port A Data 2 1 P A tir tir B B INT tiv A tsps A Data Into Port Address Data 1 0.5 ´ VCCI INT SCL Data 2 0.7 ´ VCCI R/W tiv A 0.3 ´ VCCI tir 0.5 ´ VCCP Pn 0.5 ´ VCCI INT View A−A View B−B A. CL includes probe and jig capacitance. B. All inputs are supplied by generators having the following characteristics: PRR ≤ 10 MHz, ZO = 50 Ω, tr/tf ≤ 30 ns. C. All parameters and waveforms are not applicable to all devices. Figure 19. Interrupt Load Circuit And Voltage Waveforms 12 Submit Documentation Feedback Copyright © 2009–2015, Texas Instruments Incorporated Product Folder Links: TCA6408A TCA6408A www.ti.com SCPS192D – APRIL 2009 – REVISED JULY 2015 Parameter Measurement Information (continued) 500 W Pn DUT 2 ´ VCCP CL = 50 pF (see Note A) 500 W P-PORT LOAD CONFIGURATION SCL P0 A P3 0.7 ´ VCCP 0.3 ´ VCCI Slave ACK SDA tpv (see Note B) Pn Unstable Data Last Stable Bit WRITE MODE (R/W = 0) SCL 0.7 ´ VCCI P0 A tps P3 0.3 ´ VCCI tph Pn 0.5 ´ VCCP READ MODE (R/W = 1) A. CL includes probe and jig capacitance. B. tpv is measured from 0.7 × VCC on SCL to 50% I/O (Pn) output. C. All inputs are supplied by generators having the following characteristics: PRR ≤ 10 MHz, ZO = 50 Ω, tr/tf ≤ 30 ns. D. The outputs are measured one at a time, with one transition per measurement. E. All parameters and waveforms are not applicable to all devices. Figure 20. P-Port Load Circuit And Timing Waveforms Submit Documentation Feedback Copyright © 2009–2015, Texas Instruments Incorporated Product Folder Links: TCA6408A 13 TCA6408A SCPS192D – APRIL 2009 – REVISED JULY 2015 www.ti.com Parameter Measurement Information (continued) VCCI RL = 1 kW 500 W Pn SDA DUT DUT CL = 50 pF (see Note A) SDA LOAD CONFIGURATION 2 ´ VCCP CL = 50 pF (see Note A) 500 W P-PORT LOAD CONFIGURATION Start SCL ACK or Read Cycle SDA 0.3 ´ VCCI tRESET VCCP/2 RESET tREC tREC tW VCCP/2 Pn tRESET A. CL includes probe and jig capacitance. B. All inputs are supplied by generators having the following characteristics: PRR ≤ 10 MHz, ZO = 50 Ω, tr/tf ≤ 30 ns. C. The outputs are measured one at a time, with one transition per measurement. D. I/Os are configured as inputs. E. All parameters and waveforms are not applicable to all devices. Figure 21. Reset Load Circuits And Voltage Waveforms 14 Submit Documentation Feedback Copyright © 2009–2015, Texas Instruments Incorporated Product Folder Links: TCA6408A TCA6408A www.ti.com SCPS192D – APRIL 2009 – REVISED JULY 2015 8 Detailed Description 8.1 Overview The bidirectional voltage-level translation in the TCA6408A is provided through VCCI. VCCI should be connected to the VCC of the external SCL/SDA lines. This indicates the VCC level of the I2C bus to the TCA6408A. The voltage level on the P-port of the TCA6408A is determined by VCCP. The TCA6408A consists of one 8-bit Configuration (input or output selection), Input, Output, and Polarity Inversion (active high) Register. At power on, the I/Os are configured as inputs. However, the system master can enable the I/Os as either inputs or outputs by writing to the I/O configuration bits. The data for each input or output is kept in the corresponding Input or Output Register. The polarity of the Input Port Register can be inverted with the Polarity Inversion Register. All registers can be read by the system master. The system master can reset the TCA6408A in the event of a timeout or other improper operation by asserting a low in the RESET input. The power-on reset puts the registers in their default state and initializes the I2C/SMBus state machine. The RESET pin causes the same reset/initialization to occur without depowering the part. The TCA6408A open-drain interrupt (INT) output is activated when any input state differs from its corresponding Input Port Register state and is used to indicate to the system master that an input state has changed. INT can be connected to the interrupt input of a microcontroller. By sending an interrupt signal on this line, the remote I/O can inform the microcontroller if there is incoming data on its ports without having to communicate via the I2C bus. Thus, the TCA6408A can remain a simple slave device. The device P-port outputs have high-current sink capabilities for directly driving LEDs while consuming low device current. One hardware pin (ADDR) can be used to program and vary the fixed I2C address and allow up to two devices to share the same I2C bus or SMBus. Submit Documentation Feedback Copyright © 2009–2015, Texas Instruments Incorporated Product Folder Links: TCA6408A 15 TCA6408A SCPS192D – APRIL 2009 – REVISED JULY 2015 www.ti.com 8.2 Functional Block Diagrams 13 INT Interrupt Logic LP Filter 2 ADDR 14 SCL 15 SDA I2C Bus Control Input Filter 1 VCCI 3 RESET 8 Bits I/O Port P7–P0 Write Pulse Read Pulse 16 VCCP Shift Register Power-On Reset 8 GND A. All pin numbers shown are for the PW package. B. All I/Os are set to inputs at reset. Figure 22. Logic Diagram (Positive Logic) 16 Submit Documentation Feedback Copyright © 2009–2015, Texas Instruments Incorporated Product Folder Links: TCA6408A TCA6408A www.ti.com SCPS192D – APRIL 2009 – REVISED JULY 2015 Functional Block Diagrams (continued) Data From Shift Register Data From Shift Register Output Port Register Data VCCP Configuration Register D Q Q1 FF Write Configuration Pulse CK Q D Q FF Write Pulse P0 to P7 CK Q Output Port Register Q2 Input Port Register GND Input Port Register Data Q D FF Read Pulse ESD Protection Diode CK Q To INT Data From Shift Register D Polarity Register Data Q FF Write Polarity Pulse CK Q Polarity Inversion Register A. On power up or reset, all registers return to default values. Figure 23. Simplified Schematic of P0 to P7 Submit Documentation Feedback Copyright © 2009–2015, Texas Instruments Incorporated Product Folder Links: TCA6408A 17 TCA6408A SCPS192D – APRIL 2009 – REVISED JULY 2015 www.ti.com 8.3 Feature Description 8.3.1 Voltage Translation Table 1 shows some common supply voltage options for voltage translation between the I2C bus and the P-ports of the TCA6408A. Table 1. Voltage Translation VCCI (SCL AND SDA OF I2C MASTER) (V) VCCP (P-PORT) (V) 1.8 1.8 1.8 2.5 1.8 3.3 1.8 5 2.5 1.8 2.5 2.5 2.5 3.3 2.5 5 3.3 1.8 3.3 2.5 3.3 3.3 3.3 5 5 1.8 5 2.5 5 3.3 5 5 8.3.2 I/O Port When an I/O is configured as an input, FETs Q1 and Q2 are off, which creates a high-impedance input. The input voltage may be raised above VCC to a maximum of 5.5 V. If the I/O is configured as an output, Q1 or Q2 is enabled, depending on the state of the output port register. In this case, there are low-impedance paths between the I/O pin and either VCC or GND. The external voltage applied to this I/O pin should not exceed the recommended levels for proper operation. 8.3.3 Interrupt Output (INT) An interrupt is generated by any rising or falling edge of the port inputs in the input mode. After time tiv, the signal INT is valid. Resetting the interrupt circuit is achieved when data on the port is changed to the original setting or when data is read from the port that generated the interrupt. Resetting occurs in the read mode at the acknowledge (ACK) or not acknowledge (NACK) bit after the rising edge of the SCL signal. Interrupts that occur during the ACK or NACK clock pulse can be lost (or be very short) due to the resetting of the interrupt during this pulse. Each change of the I/Os after resetting is detected and is transmitted as INT. Reading from or writing to another device does not affect the interrupt circuit, and a pin configured as an output cannot cause an interrupt. Changing an I/O from an output to an input may cause a false interrupt to occur if the state of the pin does not match the contents of the Input Port register. The INT output has an open-drain structure and requires pull-up resistor to VCCP or VCCI, depending on the application. INT should be connected to the voltage source of the device that requires the interrupt information. 8.3.4 Reset Input (RESET) The RESET input can be asserted to initialize the system while keeping the VCCP at its operating level. A reset can be accomplished by holding the RESET pin low for a minimum of tW. The TCA6408A registers and I2C/SMBus state machine are changed to their default state once RESET is low (0). When RESET is high (1), the I/O levels at the P-port can be changed externally or through the master. This input requires a pull-up resistor to VCCI, if no active connection is used. 18 Submit Documentation Feedback Copyright © 2009–2015, Texas Instruments Incorporated Product Folder Links: TCA6408A TCA6408A www.ti.com SCPS192D – APRIL 2009 – REVISED JULY 2015 8.4 Device Functional Modes 8.4.1 Power-On Reset (POR) When power (from 0 V) is applied to VCCP, an internal power-on reset holds the TCA6408A in a reset condition until VCCP has reached VPOR. At that time, the reset condition is released, and the TCA6408A registers and I2C/SMBus state machine initialize to their default states. After that, VCCP must be lowered to below VPORF and back up to the operating voltage for a power-reset cycle. 8.4.2 Powered-Up When power has been applied to both VCCP and VCCI and a POR has taken place, the device is in a functioning mode. The device will always be ready to receive new requests via the I2C bus. 8.5 Programming 8.5.1 I2C Interface The TCA6408A has a standard bidirectional I2C interface that is controlled by a master device in order to be configured or read the status of this device. Each slave on the I2C bus has a specific device address to differentiate between other slave devices that are on the same I2C bus. Many slave devices will require configuration upon startup to set the behavior of the device. This is typically done when the master accesses internal register maps of the slave, which have unique register addresses. A device can have one or multiple registers where data is stored, written, or read. The physical I2C interface consists of the serial clock (SCL) and serial data (SDA) lines. Both SDA and SCL lines must be connected to VCC through a pull-up resistor. The size of the pull-up resistor is determined by the amount of capacitance on the I2C lines. (For further details, refer to I2C Pull-up Resistor Calculation (SLVA689).) Data transfer may be initiated only when the bus is idle. A bus is considered idle if both SDA and SCL lines are high after a STOP condition. The following is the general procedure for a master to access a slave device: 1. If a master wants to send data to a slave: – Master-transmitter sends a START condition and addresses the slave-receiver. – Master-transmitter sends data to slave-receiver. – Master-transmitter terminates the transfer with a STOP condition. 2. If a master wants to receive or read data from a slave: – Master-receiver sends a START condition and addresses the slave-transmitter. – Master-receiver sends the requested register to read to slave-transmitter. – Master-receiver receives data from the slave-transmitter. Submit Documentation Feedback Copyright © 2009–2015, Texas Instruments Incorporated Product Folder Links: TCA6408A 19 TCA6408A SCPS192D – APRIL 2009 – REVISED JULY 2015 www.ti.com Programming (continued) – Master-receiver terminates the transfer with a STOP condition. SCL SDA Data Transfer START Condition STOP Condition Figure 24. Definition of Start and Stop Conditions SDA line stable while SCL line is high SCL 1 0 1 0 1 0 1 0 ACK MSB Bit Bit Bit Bit Bit Bit LSB ACK SDA Byte: 1010 1010 ( 0xAAh ) Figure 25. Bit Transfer Table 2. Interface Definition BYTE BIT 7 (MSB) 6 5 4 3 2 1 0 (LSB) I2C slave address L H L L L L ADDR R/W I/O data bus P7 P6 P5 P4 P3 P2 P1 P0 8.5.2 Bus Transactions Data must be sent to and received from the slave devices, and this is accomplished by reading from or writing to registers in the slave device. Registers are locations in the memory of the slave which contain information, whether it be the configuration information or some sampled data to send back to the master. The master must write information to these registers in order to instruct the slave device to perform a task. 20 Submit Documentation Feedback Copyright © 2009–2015, Texas Instruments Incorporated Product Folder Links: TCA6408A TCA6408A www.ti.com SCPS192D – APRIL 2009 – REVISED JULY 2015 Programming (continued) While it is common to have registers in I2C slaves, note that not all slave devices will have registers. Some devices are simple and contain only 1 register, which may be written to directly by sending the register data immediately after the slave address, instead of addressing a register. An example of a single-register device would be an 8-bit I2C switch, which is controlled via I2C commands. Since it has 1 bit to enable or disable a channel, there is only 1 register needed, and the master merely writes the register data after the slave address, skipping the register number. 8.5.2.1 Writes To write on the I2C bus, the master will send a START condition on the bus with the address of the slave, as well as the last bit (the R/W bit) set to 0, which signifies a write. After the slave sends the acknowledge bit, the master will then send the register address of the register to which it wishes to write. The slave will acknowledge again, letting the master know it is ready. After this, the master will start sending the register data to the slave until the master has sent all the data necessary (which is sometimes only a single byte), and the master will terminate the transmission with a STOP condition. Figure 26 shows an example of writing a single byte to a slave register. Master controls SDA line Slave controls SDA line Write to one register in a device Register Address N (8 bits) Device (Slave) Address (7 bits) S 0 1 0 0 0 0 START AD DR 0 R/W=0 A Data Byte to Register N (8 bits) B7 B6 B5 B4 B3 B2 B1 B0 ACK D7 D6 D5 D4 D3 D2 D1 D0 A ACK A ACK P STOP Figure 26. Write to Register <br/> Master controls SDA line Slave controls SDA line Register Address 0x02 (8 bits) Device (Slave) Address (7 bits) S 0 START 1 0 0 0 0 AD DR 0 R/W=0 A 0 ACK 0 0 0 0 0 1 Data Byte to Register 0x02 (8 bits) 0 A D7 D6 D5 D4 D3 D2 D1 D0 ACK A ACK P STOP Figure 27. Write to the Polarity Inversion Register Submit Documentation Feedback Copyright © 2009–2015, Texas Instruments Incorporated Product Folder Links: TCA6408A 21 TCA6408A SCPS192D – APRIL 2009 – REVISED JULY 2015 www.ti.com Programming (continued) 8.5.2.2 Reads Reading from a slave is very similar to writing, but requires some additional steps. In order to read from a slave, the master must first instruct the slave which register it wishes to read from. This is done by the master starting off the transmission in a similar fashion as the write, by sending the address with the R/W bit equal to 0 (signifying a write), followed by the register address it wishes to read from. Once the slave acknowledges this register address, the master will send a START condition again, followed by the slave address with the R/W bit set to 1 (signifying a read). This time, the slave will acknowledge the read request, and the master will release the SDA bus but will continue supplying the clock to the slave. During this part of the transaction, the master will become the master-receiver, and the slave will become the slave-transmitter. The master will continue to send out the clock pulses, but will release the SDA line so that the slave can transmit data. At the end of every byte of data, the master will send an ACK to the slave, letting the slave know that it is ready for more data. Once the master has received the number of bytes it is expecting, it will send a NACK, signaling to the slave to halt communications and release the bus. The master will follow this up with a STOP condition. Figure 28 shows an example of reading a single byte from a slave register. Master controls SDA line Slave controls SDA line Read from one register in a device Register Address N (8 bits) Device (Slave) Address (7 bits) S 0 1 0 0 0 0 START AD DR 0 R/W=0 A Data Byte from Register N (8 bits) Device (Slave) Address (7 bits) B7 B6 B5 B4 B3 B2 B1 B0 ACK A Sr ACK 0 1 0 0 0 0 AD DR 1 A R/W=1 Repeated START D7 D6 D5 D4 D3 D2 D1 D0 NA ACK NACK P STOP Figure 28. Read from Register 1 SCL 2 3 4 5 6 7 R 9 Data From Port Slave Address S 0 SDA 1 0 0 0 AD 0 DR 1 Start Condition R/W Data From Port Data 1 A Data 4 A ACK From Master ACK From Slave NA P NACK From Master Stop Condition Read From Port Data Into Port Data 2 tph Data 3 Data 4 Data 5 tps INT is cleared by Read from Port INT tiv Stop not needed to clear INT tir A. Transfer of data can be stopped at any time by a Stop condition. When this occurs, data present at the latest acknowledge phase is valid (output mode). It is assumed that the command byte previously has been set to 00 (read Input Port Register). B. This figure eliminates the command byte transfer, a restart, and slave address call between the initial slave address call and actual data transfer from P-port (see Figure 28). Figure 29. Read from Input Port Register 22 Submit Documentation Feedback Copyright © 2009–2015, Texas Instruments Incorporated Product Folder Links: TCA6408A TCA6408A www.ti.com SCPS192D – APRIL 2009 – REVISED JULY 2015 8.6 Register Map 8.6.1 Device Address The address of the TCA6408A is shown in Figure 30. Slave Address 0 0 1 0 Fixed 0 0 AD DR R/W Programmable Figure 30. TCA6408A Address Table 3. Address Reference ADDR I2C BUS SLAVE ADDRESS L 32 (decimal), 20 (hexadecimal) H 33 (decimal), 21 (hexadecimal) The last bit of the slave address defines the operation (read or write) to be performed. A high (1) selects a read operation, while a low (0) selects a write operation. 8.6.2 Control Register and Command Byte Following the successful acknowledgment of the address byte, the bus master sends a command byte, which is stored in the Control Register in the TCA6408A. Two bits of this data byte will state both the operation (read or write) and the internal registers (Input, Output, Polarity Inversion, or Configuration) that will be affected. This register can be written or read through the I2C bus. The command byte is sent only during a write transmission. B7 B6 B5 B4 B3 B2 B1 B0 Figure 31. Control Register Bits Table 4. Command Byte CONTROL REGISTER BITS B7 B6 B5 B4 B3 B2 B1 B0 COMMAND BYTE (HEX) 0 0 0 0 0 0 0 0 00 Input Port Read byte xxxx xxxx 0 0 0 0 0 0 0 1 01 Output Port Read/write byte 1111 1111 0 0 0 0 0 0 1 0 02 Polarity Inversion Read/write byte 0000 0000 0 0 0 0 0 0 1 1 03 Configuration Read/write byte 1111 1111 REGISTER PROTOCOL POWER-UP DEFAULT Submit Documentation Feedback Copyright © 2009–2015, Texas Instruments Incorporated Product Folder Links: TCA6408A 23 TCA6408A SCPS192D – APRIL 2009 – REVISED JULY 2015 www.ti.com 8.6.3 Register Descriptions The Input Port Register (register 0) reflects the incoming logic levels of the pins, regardless of whether the pin is defined as an input or an output by the Configuration Register. They act only on read operation. Writes to this register have no effect. The default value (X) is determined by the externally applied logic level. Before a read operation, a write transmission is sent with the command byte to indicate to the I2C device that the Input Port Register will be accessed next. Table 5. Register 0 (Input Port Register) BIT I-7 I-6 I-5 I-4 I-3 I-2 I-1 I-0 DEFAULT X X X X X X X X The Output Port Register (register 1) shows the outgoing logic levels of the pins defined as outputs by the Configuration Register. Bit values in this register have no effect on pins defined as inputs. In turn, reads from this register reflect the value that is in the flip-flop controlling the output selection, not the actual pin value. Table 6. Register 1 (Output Port Register) BIT O-7 O-6 O-5 O-4 O-3 O-2 O-1 O-0 DEFAULT 1 1 1 1 1 1 1 1 The Polarity Inversion Register (register 2) allows polarity inversion of pins defined as inputs by the Configuration Register. If a bit in this register is set (written with 1), the polarity of the corresponding port pin is inverted. If a bit in this register is cleared (written with a 0), the original polarity of the corresponding port pin is retained. Table 7. Register 2 (Polarity Inversion Register) BIT N-7 N-6 N-5 N-4 N-3 N-2 N-1 N-0 DEFAULT 0 0 0 0 0 0 0 0 The Configuration Register (register 3) configures the direction of the I/O pins. If a bit in this register is set to 1, the corresponding port pin is enabled as an input with a high-impedance output driver. If a bit in this register is cleared to 0, the corresponding port pin is enabled as an output. Table 8. Register 3 (Configuration Register) 24 BIT C-7 C-6 C-5 C-4 C-3 C-2 C-1 C-0 DEFAULT 1 1 1 1 1 1 1 1 Submit Documentation Feedback Copyright © 2009–2015, Texas Instruments Incorporated Product Folder Links: TCA6408A TCA6408A www.ti.com SCPS192D – APRIL 2009 – REVISED JULY 2015 9 Application and Implementation NOTE Information in the following applications sections is not part of the TI component specification, and TI does not warrant its accuracy or completeness. TI’s customers are responsible for determining suitability of components for their purposes. Customers should validate and test their design implementation to confirm system functionality. 9.1 Application Information Applications of the TCA6408A will have this device connected as a slave to an I2C master (processor), and the I2C bus may contain any number of other slave devices. The TCA6408A will be in a remote location from the master, placed close to the GPIOs to which the master needs to monitor or control. A typical application of the TCA6408A will operate with a lower voltage on the master side (VCCI), and a higher voltage on the P-port side (VCCP). The P-ports can be configured as outputs connected to inputs of devices such as enable, reset, power select, the gate of a switch, and LEDs. The P-ports can also be configured as inputs to receive data from interrupts, alarms, status outputs, or push buttons. Submit Documentation Feedback Copyright © 2009–2015, Texas Instruments Incorporated Product Folder Links: TCA6408A 25 TCA6408A SCPS192D – APRIL 2009 – REVISED JULY 2015 www.ti.com 9.2 Typical Application Figure 32 shows an application in which the TCA6408A can be used. VCCI VCCP VCCI (1.8 V) VCCI VCCP 14 SCL 15 P0 SDA 13 INT 3 RESET SCL Master Controller SDA INT GND 16 1 10 kW (´ 4) VCC RESET 100 kW (´ 3) ALARM (see Note D) Subsystem 1 (e.g., Alarm) 4 A 5 P1 ENABLE B TCA6408A P2 2 ADDR P3 P4 P5 P6 P7 6 7 9 Keypad 10 11 12 GND 8 A. Device address configured as 0100000 for this example. B. P0 and P2–P4 are configured as inputs. C. P1 and P5–P7 are configured as outputs. D. Resistors are required for inputs (on P-port) that may float. If a driver to an input will never let the input float, a resistor is not needed. Outputs (in the P-port) do not need pull-up resistors. Figure 32. Typical Application Schematic 9.2.1 Design Requirements Table 9. Design Parameters DESIGN PARAMETER EXAMPLE VALUE 2 I C input voltage (VCCI) 1.8 V P-port input/output voltage (VCCP) 5V Output current rating, P-port sinking (IOL) Output current rating, P-port sourcing (IOH) I2C bus clock (SCL) speed 26 25 mA 10 mA 400 kHz Submit Documentation Feedback Copyright © 2009–2015, Texas Instruments Incorporated Product Folder Links: TCA6408A TCA6408A www.ti.com SCPS192D – APRIL 2009 – REVISED JULY 2015 9.2.2 Detailed Design Procedure The pull-up resistors, RP, for the SCL and SDA lines need to be selected appropriately and take into consideration the total capacitance of all slaves on the I2C bus. The minimum pull-up resistance is a function of VCC, VOL,(max), and IOL: Rp(min) = VCC - VOL(max) IOL (1) The maximum pull-up resistance is a function of the maximum rise time, tr (300 ns for fast-mode operation, fSCL = 400 kHz) and bus capacitance, Cb: Rp(max) = tr 0.8473 ´ Cb (2) The maximum bus capacitance for an I2C bus must not exceed 400 pF for standard-mode or fast-mode operation. The bus capacitance can be approximated by adding the capacitance of the TCA9538, Ci for SCL or Cio for SDA, the capacitance of wires, connections, and traces, and the capacitance of additional slaves on the bus. 9.2.2.1 Minimizing ICC When I/O is Used to Control LEDs When the I/Os are used to control LEDs, normally they are connected to VCC through a resistor as shown in Figure 32. The LED acts as a diode, so when the LED is off, the I/O VIN is about 1.2 V less than VCC. The ΔICC parameter in Electrical Characteristics shows how ICC increases as VIN becomes lower than VCC. Designs that must minimize current consumption, such as battery power applications, should consider maintaining the I/O pins greater than or equal to VCC when the LED is off. Figure 33 shows a high-value resistor in parallel with the LED. Figure 34 shows VCC less than the LED supply voltage by at least 1.2 V. Both of these methods maintain the I/O VIN at or above VCC and prevent additional supply current consumption when the LED is off. VCC LED 100 kΩ VCC Px Figure 33. High-Value Resistor in Parallel With LED 3.3 V 5V LED VCC Px Figure 34. Device Supplied by a Low Voltage Submit Documentation Feedback Copyright © 2009–2015, Texas Instruments Incorporated Product Folder Links: TCA6408A 27 TCA6408A SCPS192D – APRIL 2009 – REVISED JULY 2015 www.ti.com 9.2.3 Application Curves 25 1.8 Standard-mode Fast-mode 1.6 1.4 Rp(min) (kOhm) Rp(max) (kOhm) 20 15 10 1.2 1 0.8 0.6 0.4 5 VCC > 2V VCC <= 2 0.2 0 0 0 50 100 150 200 250 Cb (pF) 300 350 400 450 0.5 1 1.5 2 2.5 3 VCC (V) 3.5 4 4.5 5 5.5 D009 VOL = 0.2 × VCC, IOL = 2 mA when VCC ≤ 2 V VOL = 0.4 V, IOL = 3 mA when VCC > 2 V Standard-mode: fSCL= 100 kHz, tr = 1 µs Fast-mode: fSCL= 400 kHz, tr= 300 ns Figure 35. Maximum Pullup Resistance (Rp(max)) vs Bus Capacitance (Cb) 28 0 D008 Figure 36. Minimum Pullup Resistance (Rp(min)) vs Pullup Reference Voltage (VCC) Submit Documentation Feedback Copyright © 2009–2015, Texas Instruments Incorporated Product Folder Links: TCA6408A TCA6408A www.ti.com SCPS192D – APRIL 2009 – REVISED JULY 2015 10 Power Supply Recommendations 10.1 Power-On Reset Requirements In the event of a glitch or data corruption, TCA6408A can be reset to its default conditions by using the power-on reset feature. Power-on reset requires that the device go through a power cycle to be completely reset. This reset also happens when the device is powered on for the first time in an application. The two types of power-on reset are shown in Figure 37 and Figure 38. VCC Ramp-Up Re-Ramp-Up Ramp-Down tTRR_GND Time tRT Time to Re-Ramp tFT tRT Figure 37. VCC is Lowered Below 0.2 V Or 0 V and then Ramped Up to VCC VCC Ramp-Down Ramp-Up tTRR_VPOR50 VIN drops below POR levels Time Time to Re-Ramp tFT tRT Figure 38. VCC is Lowered Below the POR Threshold, then Ramped Back Up to VCC Table 10 specifies the performance of the power-on reset feature for TCA6408A for both types of power-on reset. Table 10. Recommended Supply Sequencing and Ramp Rates at TA = 25°C (1) PARAMETER MIN TYP MAX UNIT tFT Fall rate See Figure 37 0.1 2000 ms tRT Rise rate See Figure 37 0.1 2000 ms tRR_GND Time to re-ramp (when VCC drops to GND) See Figure 37 1 μs tRR_POR50 Time to re-ramp (when VCC drops to VPOR_MIN – 50 mV) See Figure 38 1 μs VCC_GH Level that VCCP can glitch down to, but not cause a functional disruption when VCCX_GW = 1 μs See Figure 39 1.2 V tGW Glitch width that will not cause a functional disruption when VCCX_GH = 0.5 × VCCx See Figure 39 10 μs VPORF Voltage trip point of POR on falling VCC VPORR Voltage trip point of POR on fising VCC (1) 0.7 V 1.4 V Not tested. Specified by design. Submit Documentation Feedback Copyright © 2009–2015, Texas Instruments Incorporated Product Folder Links: TCA6408A 29 TCA6408A SCPS192D – APRIL 2009 – REVISED JULY 2015 www.ti.com Glitches in the power supply can also affect the power-on reset performance of this device. The glitch width (tGW) and height (tGH) are dependent on each other. The bypass capacitance, source impedance, and device impedance are factors that affect power-on reset performance. Figure 39 and Table 10 provide more information on how to measure these specifications. VCC tGH Time tGW Figure 39. Glitch Width And Glitch Height VPOR is critical to the power-on reset. VPOR is the voltage level at which the reset condition is released and all the registers and the I2C/SMBus state machine are initialized to their default states. The value of VPOR differs based on the VCC being lowered to or from 0. Figure 40 and Table 10 provide more details on this specification. VCC VPOR VPORF Time POR Time Figure 40. VPOR 30 Submit Documentation Feedback Copyright © 2009–2015, Texas Instruments Incorporated Product Folder Links: TCA6408A TCA6408A www.ti.com SCPS192D – APRIL 2009 – REVISED JULY 2015 11 Layout 11.1 Layout Guidelines For printed circuit board (PCB) layout of the TCA6408A, common PCB layout practices should be followed, but additional concerns related to high-speed data transfer such as matched impedances and differential pairs are not a concern for I2C signal speeds. In all PCB layouts, it is a best practice to avoid right angles in signal traces, to fan out signal traces away from each other upon leaving the vicinity of an integrated circuit (IC), and to use thicker trace widths to carry higher amounts of current that commonly pass through power and ground traces. By-pass and de-coupling capacitors are commonly used to control the voltage on the VCCP pin, using a larger capacitor to provide additional power in the event of a short power supply glitch and a smaller capacitor to filter out high-frequency ripple. These capacitors should be placed as close to the TCA6408A as possible. These best practices are shown in Layout Example. For the layout example provided in Layout Example, it would be possible to fabricate a PCB with only 2 layers by using the top layer for signal routing and the bottom layer as a split plane for power (VCCI and VCCP) and ground (GND). However, a 4-layer board is preferable for boards with higher density signal routing. On a 4-layer PCB, it is common to route signals on the top and bottom layer, dedicate one internal layer to a ground plane, and dedicate the other internal layer to a power plane. In a board layout using planes or split planes for power and ground, vias are placed directly next to the surface mount component pad which needs to attach to VCCI, VCCP, or GND and the via is connected electrically to the internal layer or the other side of the board. Vias are also used when a signal trace needs to be routed to the opposite side of the board, but this technique is not demonstrated in Layout Example. 11.2 Layout Example = Via to GND Plane 0402 Cap 0402 Cap To CPU/MCU VCCI VCCP ADDR SDA RST SCL INT P0 TCA6408A P1 P7 P2 P6 P3 P5 GND P4 Figure 41. Example Layout (PW Package) Submit Documentation Feedback Copyright © 2009–2015, Texas Instruments Incorporated Product Folder Links: TCA6408A 31 TCA6408A SCPS192D – APRIL 2009 – REVISED JULY 2015 www.ti.com 12 Device and Documentation Support 12.1 Community Resources The following links connect to TI community resources. Linked contents are provided "AS IS" by the respective contributors. They do not constitute TI specifications and do not necessarily reflect TI's views; see TI's Terms of Use. TI E2E™ Online Community TI's Engineer-to-Engineer (E2E) Community. Created to foster collaboration among engineers. At e2e.ti.com, you can ask questions, share knowledge, explore ideas and help solve problems with fellow engineers. Design Support TI's Design Support Quickly find helpful E2E forums along with design support tools and contact information for technical support. 12.2 Trademarks E2E is a trademark of Texas Instruments. All other trademarks are the property of their respective owners. 12.3 Electrostatic Discharge Caution These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam during storage or handling to prevent electrostatic damage to the MOS gates. 12.4 Glossary SLYZ022 — TI Glossary. This glossary lists and explains terms, acronyms, and definitions. 13 Mechanical, Packaging, and Orderable Information The following pages include mechanical, packaging, and orderable information. This information is the most current data available for the designated devices. This data is subject to change without notice and revision of this document. For browser-based versions of this data sheet, refer to the left-hand navigation. 32 Submit Documentation Feedback Copyright © 2009–2015, Texas Instruments Incorporated Product Folder Links: TCA6408A PACKAGE OPTION ADDENDUM www.ti.com 5-Feb-2014 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan Lead/Ball Finish MSL Peak Temp (2) (6) (3) Op Temp (°C) Device Marking (4/5) TCA6408APWR ACTIVE TSSOP PW 16 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 PH408A TCA6408ARGTR ACTIVE QFN RGT 16 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR -40 to 85 ZVU TCA6408ARSVR ACTIVE UQFN RSV 16 3000 Green (RoHS & no Sb/Br) CU NIPDAUAG Level-1-260C-UNLIM -40 to 85 ZVU (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. (4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device. (5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation of the previous line and the two combined represent the entire Device Marking for that device. (6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish value exceeds the maximum column width. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and Addendum-Page 1 Samples PACKAGE OPTION ADDENDUM www.ti.com 5-Feb-2014 continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 2 PACKAGE MATERIALS INFORMATION www.ti.com 11-Oct-2013 TAPE AND REEL INFORMATION *All dimensions are nominal Device TCA6408APWR Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant TSSOP PW 16 2000 330.0 12.4 6.9 5.6 1.6 8.0 12.0 Q1 TCA6408ARGTR QFN RGT 16 3000 330.0 12.4 3.3 3.3 1.1 8.0 12.0 Q2 TCA6408ARSVR UQFN RSV 16 3000 177.8 12.4 2.0 2.8 0.7 4.0 12.0 Q1 Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 11-Oct-2013 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) TCA6408APWR TSSOP PW 16 2000 367.0 367.0 35.0 TCA6408ARGTR QFN RGT 16 3000 367.0 367.0 35.0 TCA6408ARSVR UQFN RSV 16 3000 202.0 201.0 28.0 Pack Materials-Page 2 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of non-designated products, TI will not be responsible for any failure to meet ISO/TS16949. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP® Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2015, Texas Instruments Incorporated