TI SN751178N

SN751177, SN751178
DUAL DIFFERENTIAL DRIVERS AND RECEIVERS
SLLS059D – FEBRUARY 1990 – REVISED MAY 1999
D
D
D
D
D
D
D
D
D
D
D
Meet or Exceed the Requirements of ANSI
Standards TIA/EIA-422-B and TIA/EIA-485-A
and ITU Recommendations V.10 and V.11
Designed for Multipoint Bus Transmission
on Long Bus Lines in Noise Environments
Driver Positive- and Negative-Current
Limiting
Thermal Shutdown Protection
Driver 3-State Outputs
Receiver Common-Mode Input Voltage
Range of –12 V to 12 V
Receiver Input Sensitivity . . . ±200 mV
Receiver Hysteresis . . . 50 mV Typ
Receiver Input Impedance . . . 12 kΩ Min
Receiver 3-State Outputs (SN751177 Only)
Operate From Single 5-V Supply
SN751177 . . . N OR NS† PACKAGE
(TOP VIEW)
1B
1A
1R
RE
2R
2A
2B
GND
16
2
15
3
14
4
13
5
12
6
11
7
10
8
9
VCC
1D
1Y
1Z
DE
2Z
2Y
2D
SN751178 . . . N OR NS† PACKAGE
(TOP VIEW)
1B
1A
1R
1DE
2R
2A
2B
GND
description
The SN751177 and SN751178 dual differential
drivers and receivers are monolithic integrated
circuits that are designed for balanced multipoint
bus transmission at rates up to 10 Mbit/s. They are
designed to improve the performance of
full-duplex data communications over long bus
lines and meet ANSI Standards TIA/EIA-422-B
and TIA/EIA-485-A and ITU Recommendations
V.10 and V.11.
1
1
16
2
15
3
14
4
13
5
12
6
11
7
10
8
9
VCC
1D
1Y
1Z
2DE
2Z
2Y
2D
† The NS package is only available taped and reeled.
The SN751177 and SN751178 driver outputs provide limiting for both positive and negative currents and
thermal-shutdown protection from line-fault conditions on the transmission bus line.
The receiver features high input impedance of at least 12 kΩ, an input sensitivity of ±200 mV over a
common-mode input voltage range of –12 V to 12 V, and typical input hysteresis of 50 mV. Fail-safe design
ensures that if the receiver inputs are open, the receiver outputs always will be high.
The SN751177 and SN751178 are characterized for operation from –20°C to 85°C.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
Copyright  1999, Texas Instruments Incorporated
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of Texas Instruments
standard warranty. Production processing does not necessarily include
testing of all parameters.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
1
SN751177, SN751178
DUAL DIFFERENTIAL DRIVERS AND RECEIVERS
SLLS059D – FEBRUARY 1990 – REVISED MAY 1999
Function Tables
SN751177, SN751178
(each driver)
OUTPUTS
INPUT
D
ENABLE
DE
H
H
H
L
L
H
L
H
X
L
Z
Z
Y
Z
H = high level, L = low level, X = irrelevant,
Z = high impedance (off)
SN751177
(each receiver)
DIFFERENTIAL INPUTS
A–B
ENABLE
RE
OUTPUT
R
VID ≥ 0.2 V
–0.2 V < VID < 0.2 V
L
H
L
?
VID ≤ –0.2 V
X
L
L
H
Z
Open
L
H
H = high level, L = low level, ? = indeterminate,
X = irrelevant, Z = high impedance (off)
SN751178
(each receiver)
DIFFERENTIAL INPUTS
A–B
OUTPUT
R
VID ≥ 0.2 V
–0.2 V < VID < 0.2 V
H
VID ≤ –0.2 V
H = high level, L
? = indeterminate
2
POST OFFICE BOX 655303
?
L
=
low
level,
• DALLAS, TEXAS 75265
SN751177, SN751178
DUAL DIFFERENTIAL DRIVERS AND RECEIVERS
SLLS059D – FEBRUARY 1990 – REVISED MAY 1999
logic symbols†
logic diagrams (positive logic)
SN751177
DE
12
4
RE
1D
1R
2D
2R
SN751177
EN1
DE
12
EN2
14
1
15
13
1
2
3
2
1
9
10
1
11
1
6
5
2
7
RE
1Y
4
14
1Z
1D
15
13
1A
2
1B
1R
3
1
2Y
10
2Z
2D
2A
9
11
6
2B
2R
5
7
1Y
1Z
1A
1B
2Y
2Z
2A
2B
SN751178
1DE
1D
4
14
EN
15
13
2
1R
2DE
2D
2R
3
12
1
10
EN
9
11
6
5
7
SN751178
1Y
1Z
1DE
1A
1D
4
14
15
1B
13
2
2Y
1R
2Z
2DE
2A
2D
3
1
12
10
9
2B
11
6
2R
† These symbols are in accordance with ANSI/IEEE Std 91-1984 and
IEC Publication 617-12.
5
7
1Y
1Z
1A
1B
2Y
2Z
2A
2B
schematics of inputs
EQUIVALENT OF DRIVER OR ENABLE INPUT
VCC
EQUIVALENT OF RECEIVER INPUT
VCC
R(eq)
Input
Input
Driver Input: R(eq) = 6 kΩ NOM
Enable Input: R(eq) = 4 kΩ NOM
R(eq) = Equivalent Resistor
All resistor values are nominal.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
3
SN751177, SN751178
DUAL DIFFERENTIAL DRIVERS AND RECEIVERS
SLLS059D – FEBRUARY 1990 – REVISED MAY 1999
schematics of outputs
TYPICAL OF ALL DRIVER OUTPUTS
TYPICAL OF ALL RECEIVER OUTPUTS
VCC
85 Ω
NOM
VCC
Output
Output
GND
All resistor values are nominal.
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)†
Supply voltage, VCC (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Input voltage, VI (DE, RE, and D inputs) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Receiver input voltage range, VI (A or B inputs) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –25 V to 25 V
Receiver differential input voltage range, VID (see Note 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –25 V to 25 V
Driver output voltage range, VO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –10 V to 15 V
Receiver low-level output current, IOL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 mA
Package thermal impedance, θJA (see Note 3): N package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78°C/W
NS package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111°C/W
Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –65°C to 150°C
Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 260°C
† Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
NOTES: 1. All voltage values, except differential input voltage, are with respect to the network ground terminal.
2. Differential input voltage is measured at the noninverting terminal with respect to the inverting terminal.
3. The package thermal impedance is calculated in accordance with JESD 51, except for through-hole packages, which use a trace
length of zero.
4
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
SN751177, SN751178
DUAL DIFFERENTIAL DRIVERS AND RECEIVERS
SLLS059D – FEBRUARY 1990 – REVISED MAY 1999
recommended operating conditions
Supply voltage, VCC
High-level input voltage, VIH
MIN
NOM
MAX
UNIT
4.75
5
5.25
V
2
DE RE,
RE and D inp
ts
DE,
inputs
Low-level input voltage, VIL
–7†
Common-mode output voltage, VOC
V
0.8
V
12
V
–60
mA
60
mA
Common-mode input voltage, VIC
±12
V
Differential input voltage, VID
±12
V
Driver
High-level output current, IOH
Low-level output current, IOL
Receiver
High-level output current, IOH
Low-level output current, IOL
–400
µA
16
mA
Operating free-air temperature, TA
–20
85
°C
† The algebraic convention, where the less positive (more negative) limit is designated as minimum, is used in this data sheet for common-mode
output and threshold voltage levels only.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
5
SN751177, SN751178
DUAL DIFFERENTIAL DRIVERS AND RECEIVERS
SLLS059D – FEBRUARY 1990 – REVISED MAY 1999
DRIVER SECTIONS
electrical characteristics over recommended ranges of supply voltage and operating free-air
temperature (unless otherwise noted)
PARAMETER
VIK
VOH
Input clamp voltage
VOL
|VOD1|
Low-level output voltage
|VOD2|
TEST CONDITIONS
II = –18 mA
VIH = 2 V,
High-level output voltage
VIH = 2 V,
IO = 0
Differential output voltage
Differential output voltage
g
VOD3
Differential output voltage
∆|VOD|
Change in magnitude of
differential output voltage (see Note 5)
VOC
Common-mode output voltage
∆|VOC|
Change in magnitude of
common-mode output voltage (see Note 5)
IO
IOZ
Output current with power off
IIH
IIL
High-level input current
IOS
ICC
VIL = 0.8 V,
VIL = 0.8 V,
TYP†
IOH = –33 mA
IOH = 33 mA
See Figure 1
RL = 54 Ω,
See Figure 1
RL = 54 Ω or 100 Ω,
UNIT
–1.5
V
3.7
V
1.1
V
1.5
RL = 100 Ω
Ω,
MAX
6
2 or
1/2 VOD1‡
See Note 4
High-impedance-state output current
MIN
See Figure 1
V
1.5
5
1.5
5
V
±0.2
V
3
V
±0.2
V
±100
µA
±100
µA
20
µA
–100
µA
–1§
VCC = 0,
VO = –7 V to 12 V
VO = –7 V to 12 V
Low-level input current
VIH = 2.7 V
VIL = 0.4 V
–250
Short-circuit output current (see Note 6)
VO = –7 V
VO = VCC
VO = 12 V
250
Supply current
No load
V
250
Outputs enabled
80
110
Outputs disabled
50
80
mA
mA
† All typical values are at VCC = 5 V and TA = 25°C.
‡ The minimum VOD2 with a 100-Ω load is either 1/2 VOD1 or 2 V, whichever is greater.
§ The algebraic convention, where the less positive (more negative) limit is designated as minimum, is used in this data sheet for common-mode
output and threshold voltage levels only.
NOTES: 4. See TIA/EIA-485-A Figure 3.5, Test Termination Measurement 2
5. ∆|VOD| and ∆|VOC| are the changes in magnitude of VOD and VOC, respectively, that occur when the input is changed from a high
level to a low level.
6. Not more than one output should be shorted at a time, and the duration of the short circuit should not exceed one second.
switching characteristics at VCC = 5 V, CL = 50 pF, TA = 25°C
PARAMETER
6
TEST CONDITIONS
td(OD)
tt(OD)
Differential output delay time
tPLH
tPHL
Propagation delay time, low- to high-level output
tPZH
tPZL
tPHZ
tPLZ
RL = 54 Ω
Ω,
Differential output transition time
See Figure 3
MIN
TYP
MAX
20
25
UNIT
ns
27
35
ns
20
25
ns
20
25
ns
RL = 27 Ω
Ω,
See Figure 4
Output enable time to high level
RL = 110 Ω,
See Figure 5
80
120
ns
Output enable time to low level
RL = 110 Ω,
See Figure 6
40
60
ns
Output disable time from high level
RL = 110 Ω,
See Figure 5
90
120
ns
Output disable time from low level
RL = 110 Ω,
See Figure 6
30
45
ns
Propagation delay time, high- to low-level output
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
SN751177, SN751178
DUAL DIFFERENTIAL DRIVERS AND RECEIVERS
SLLS059D – FEBRUARY 1990 – REVISED MAY 1999
SYMBOL EQUIVALENTS
DATA-SHEET
PARAMETER
TIA/EIA-422-B
TIA/EIA-485-A
VO
Vt (RL = 100 Ω)
VO
Vt (RL = 54 Ω)
Vt (Test Termination
Measurement 2)
∆|VOD|
| |Vt| – |Vt| |
| |Vt| – |Vt| |
VOC
∆|VOC|
|VOS|
|VOS|
|VOS – VOS|
|VOD1|
|VOD2|
|VOD3|
|VOS – VOS|
IOS
IO
|Isa|, |Isb|
|Ixa|, |Ixb|
Iia, Iib
RECEIVER SECTIONS
electrical characteristics over recommended ranges of common-mode input voltage, supply
voltage, and operating free-air temperature (unless otherwise noted)
PARAMETER
VIT+
TEST CONDITIONS
Positive-going input threshold voltage
VIT–
Negative-going input threshold voltage
Vhys
VIK
Input hysteresis voltage (VIT+ – VIT–)
VOH
High-level output voltage
VO = 2.7 V,
VO = 0.5 V,
Low level output voltage
Low-level
IOZ
High-impedance-state output current
SN751177
II = –18 mA
VID = 200 mV,
VID = –200
200 mV
SN751177
II
Line input current (see Note 7)
IIH
IIL
High-level enable input current
SN751177
Low-level enable input current
SN751177
IOS
ICC
Short-circuit output current (see Note 6)
Supply current
TYP†
IO = –0.4 mA
IO = 16 mA
MAX
0.2
–0.2‡
2.7
IOL = 16 mA
0.5
±20
VI = 12 V
VI = –7 V
1
–0.8
VIH = 2.7 V
VIL = 0.4 V
–15
No load,
Outputs enabled
V
V
0.45
VO = 0.4 V to 2.4 V
Other input at 0 V
V
mV
–1.5
IOH = –400 µA
IOL = 8 mA
UNIT
V
50
Enable clamp voltage
VOL
MIN
80
V
µA
mA
20
µA
–100
µA
–85
µA
110
mA
ri
Input resistance
12
kΩ
† All typical values are at VCC = 5 V and TA = 25°C.
‡ The algebraic convention, where the less positive (more negative) limit is designated as minimum, is used in this data sheet for common-mode
output and threshold voltage levels only.
NOTES: 6. Not more than one output should be shorted at a time, and the duration of the short circuit should not exceed one second.
7. Refer to ANSI Standards TIA/EIA-422-B, TIA/EIA-423-A, and TIA/EIA-485-A for exact conditions.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
7
SN751177, SN751178
DUAL DIFFERENTIAL DRIVERS AND RECEIVERS
SLLS059D – FEBRUARY 1990 – REVISED MAY 1999
switching characteristics at VCC = 5 V, CL = 15 pF, TA = 25°C
PARAMETER
TEST CONDITIONS
tPLH
tPHL
Propagation delay time, low- to high-level output
tPZH
tPZL
Output enable time to high level
tPHZ
tPLZ
Output disable time from high level
1 5 V to 1.5
1 5 V,
V
VID = –1.5
Propagation delay time, high- to low-level output
Output enable time to low level
SN751177
MIN
TYP
MAX
20
35
ns
22
35
ns
17
25
ns
20
27
ns
25
40
ns
30
40
ns
See Figure 7
See Figure 8
Output disable time from low level
UNIT
PARAMETER MEASUREMENT INFORMATION
RL
2
VOD2
RL
2
VOC
Figure 1. Driver Test Circuit, VOD and VOC
VID
VOH
VOL
–IOH
+IOL
Figure 2. Receiver Test Circuit, VOH and VOL
RL = 54 Ω
CL = 50 pF
Output
(see Note A)
3V
Input
3V
1.5 V
1.5 V
0V
td(OD)
Generator
(see Note B)
50 Ω
Output
td(OD)
50%
10%
90%
90%
≈ 2.5 V
50%
10%
tt(OD)
TEST CIRCUIT
≈ –2.5 V
tt(OD)
VOLTAGE WAVEFORMS
NOTES: A. CL includes probe and jig capacitance.
B. The pulse generator has the following characteristics: PRR ≤ 1 MHz, 50% duty cycle, ZO = 50 Ω, tr ≤ 6 ns, tf ≤ 6 ns.
Figure 3. Driver Differential Output-Delay and Transition-Time Test Circuit and Voltage Waveforms
8
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
SN751177, SN751178
DUAL DIFFERENTIAL DRIVERS AND RECEIVERS
SLLS059D – FEBRUARY 1990 – REVISED MAY 1999
PARAMETER MEASUREMENT INFORMATION
3V
1.5 V
Input
1.5 V
0V
2.3 V
tPLH
RL = 27 Ω
S1
Output
Generator
(see Note B)
50 Ω
CL = 15 pF
(see Note A)
3V
tPHL
VOH
Y
Output
2.3 V
2.3 V
VOL
tPHL
tPLH
VOH
Z
Output
2.3 V
2.3 V
VOL
TEST CIRCUIT
VOLTAGE WAVEFORMS
NOTES: A. CL includes probe and jig capacitance.
B. The pulse generator has the following characteristics: PRR ≤ 1 MHz, 50% duty cycle, ZO = 50 Ω, tr ≤ 6 ns, tf ≤ 6 ns.
Figure 4. Driver Propagation-Time Test Circuit and Voltage Waveforms
Output
S1
3V
1.5 V
Input
1.5 V
0 V or 3 V
Generator
(see Note B)
0V
50 Ω
CL = 15 pF
(see Note A)
tPZH
RL = 110 Ω
0.5 V
VOH
Output
2.3 V
Voff ≈ 0 V
tPHZ
TEST CIRCUIT
VOLTAGE WAVEFORMS
NOTES: A. CL includes probe and jig capacitance.
B. The pulse generator has the following characteristics: PRR ≤ 1 MHz, 50% duty cycle, ZO = 50 Ω, tr ≤ 6 ns, tf ≤ 6 ns.
Figure 5. Driver Enable- and Disable-Time Test Circuit and Voltage Waveforms
5V
RL = 110 Ω
S1
Output
3V
Input
1.5 V
1.5 V
0V
0 V or 3 V
Generator
(see Note B)
50 Ω
tPZL
CL = 15 pF
(see Note A)
tPLZ
5V
2.3 V
Output
VOL
0.5 V
TEST CIRCUIT
VOLTAGE WAVEFORMS
NOTES: A. CL includes probe and jig capacitance.
B. The pulse generator has the following characteristics: PRR ≤ 1 MHz, 50% duty cycle, ZO = 50 Ω, tr ≤ 6 ns, tf ≤ 6 ns.
Figure 6. Driver Enable- and Disable-Time Test Circuit and Voltage Waveforms
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
9
SN751177, SN751178
DUAL DIFFERENTIAL DRIVERS AND RECEIVERS
SLLS059D – FEBRUARY 1990 – REVISED MAY 1999
PARAMETER MEASUREMENT INFORMATION
3V
Output
Generator
(see Note B)
50 Ω
1.5 V
Input
0V
tPLH
CL = 15 pF
(see Note A)
1.5 V
1.5 V
0V
tPHL
1.3 V
Output
VOH
1.3 V
VOL
TEST CIRCUIT
VOLTAGE WAVEFORMS
NOTES: A. CL includes probe and jig capacitance.
B. The pulse generator has the following characteristics: PRR ≤ 1 MHz, 50% duty cycle, ZO = 50 Ω, tr ≤ 6 ns, tf ≤ 6 ns.
Figure 7. Receiver Propagation-Time Test Circuit and Voltage Waveforms
S1
1.5 V
2 kΩ
S2
5V
–1.5 V
CL = 15 pF
(see Note A)
Generator
(see Note B)
5 kΩ
1N916 or Equivalent
50 Ω
S3
TEST CIRCUIT
3V
1.5 V
0 V S1 to 1.5 V
S3 Closed
VOH S2 Open
Input
tPZH
Output
1.5 V
3V
1.5 V
0V
Input
tPZL
≈ 4.5 V
1.5 V
VOL
Output
0V
3V
3V
Input
Input
1.5 V
0V
tPHZ
VOH
1.5 V
0V
S1 to 1.5 V
S2 Closed
S3 Closed
Output
tPLZ
≈ 1.3 V
Output
0.5 V
S1 to –1.5 V
S2 Closed
S3 Open
≈ 1.3 V
S1 to –1.5 V
S2 Closed
S3 Closed
0.5 V
VOL
VOLTAGE WAVEFORMS
NOTES: A. CL includes probe and jig capacitance.
B. The pulse generator has the following characteristics: PRR ≤ 1 MHz, 50% duty cycle, ZO = 50 Ω, tr ≤ 6 ns, tf ≤ 6 ns.
Figure 8. Receiver Output Enable- and Disable-Time Test Circuit and Voltage Waveforms
10
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
IMPORTANT NOTICE
Texas Instruments and its subsidiaries (TI) reserve the right to make changes to their products or to discontinue
any product or service without notice, and advise customers to obtain the latest version of relevant information
to verify, before placing orders, that information being relied on is current and complete. All products are sold
subject to the terms and conditions of sale supplied at the time of order acknowledgement, including those
pertaining to warranty, patent infringement, and limitation of liability.
TI warrants performance of its semiconductor products to the specifications applicable at the time of sale in
accordance with TI’s standard warranty. Testing and other quality control techniques are utilized to the extent
TI deems necessary to support this warranty. Specific testing of all parameters of each device is not necessarily
performed, except those mandated by government requirements.
CERTAIN APPLICATIONS USING SEMICONDUCTOR PRODUCTS MAY INVOLVE POTENTIAL RISKS OF
DEATH, PERSONAL INJURY, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE (“CRITICAL
APPLICATIONS”). TI SEMICONDUCTOR PRODUCTS ARE NOT DESIGNED, AUTHORIZED, OR
WARRANTED TO BE SUITABLE FOR USE IN LIFE-SUPPORT DEVICES OR SYSTEMS OR OTHER
CRITICAL APPLICATIONS. INCLUSION OF TI PRODUCTS IN SUCH APPLICATIONS IS UNDERSTOOD TO
BE FULLY AT THE CUSTOMER’S RISK.
In order to minimize risks associated with the customer’s applications, adequate design and operating
safeguards must be provided by the customer to minimize inherent or procedural hazards.
TI assumes no liability for applications assistance or customer product design. TI does not warrant or represent
that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other
intellectual property right of TI covering or relating to any combination, machine, or process in which such
semiconductor products or services might be or are used. TI’s publication of information regarding any third
party’s products or services does not constitute TI’s approval, warranty or endorsement thereof.
Copyright  1999, Texas Instruments Incorporated