■ Differential D and Q ■ Extended 100E VEE range of –4.2V to –5.5V The SY10/100E416 are 5-bit differential line receiving devices. The 2.0GHz of bandwidth provided by the high frequency outputs make the devices ideal for buffering of very high speed oscillators. A VBB pin is available to AC couple an input signal to the devices. The design incorporates two stages of gain internal to the devices, making them an excellent choice for use in high bandwidth amplifier applications. VBB output for single-ended use 600ps max. propagation delay High frequency outputs 2 stages of gain Internal 75KΩ input pull-down resistors Fully compatible with Motorola 10E/100E416 Available in 28-pin PLCC package PIN NAMES BLOCK DIAGRAM Pin D0 D0 SY100E416 DESCRIPTION FEATURES ■ ■ ■ ■ ■ ■ ■ SY10E416 SY100E416 SY10E416 QUINT DIFFERENTIAL LINE RECEIVER Micrel, Inc. Q0 Q0 D1 D0 Q1 Q1 D2 D2 Q2 Q2 D3 D3 Q3 Q3 D4 D4 Q4 Q4 Function D[0:4], D[0:4] Differential Data Inputs Q[0:4], Q[0:4] Differential Data Outputs VCCO VCC to Output VBB M9999-032206 [email protected] or (408) 955-1690 Rev.: F 1 Amendment: /0 Issue Date: March 2006 SY10E416 SY100E416 Micrel, Inc. Ordering Information(1) Q4 Q4 VCCO D3 D4 D4 VCCO PACKAGE/ORDERING INFORMATION 25 24 23 22 21 20 19 Part Number Package Type Operating Range Package Marking Lead Finish J28-1 Industrial SY10E416JI Sn-Pb D3 26 18 Q3 SY10E416JI D2 27 17 Q3 D2 SY10E416JITR(2) J28-1 Industrial SY10E416JI Sn-Pb 28 16 VCC VEE VBB 1 15 Q2 SY100E416JI J28-1 Industrial SY100E416JI Sn-Pb 2 J28-1 Industrial SY100E416JI Sn-Pb D0 3 13 Q2 VCCO SY100E416JITR(2) SY10E416JC J28-1 Commercial SY10E416JC Sn-Pb D0 4 12 Q1 SY10E416JCTR(2) J28-1 Commercial SY10E416JC Sn-Pb SY100E416JC J28-1 Commercial SY100E416JC Sn-Pb SY100E416JCTR(2) J28-1 Commercial SY100E416JC Sn-Pb SY10E416JY(3) J28-1 Industiral SY10E416JY with Pb-Free bar-line indicator Matte-Sn SY10E416JYTR(2, 3) J28-1 Industrial SY10E416JY with Pb-Free bar-line indicator Matte-Sn SY100E416JY(3) J28-1 Industrial SY100E416JY with Pb-Free bar-line indicator Matte-Sn SY100E416JYTR(2, 3) J28-1 Industrial SY100E416JY with Pb-Free bar-line indicator Matte-Sn TOP VIEW PLCC J28-1 8 9 10 11 VCCO Q1 7 VCCO Q0 Q0 D1 6 D1 5 14 28-Pin PLCC (J28-1) Notes: 1. Contact factory for die availability. Dice are guaranteed at TA = 25°C, DC Electricals only. 2. Tape and Reel. 3. Pb-Free package is recommended for new designs. M9999-032206 [email protected] or (408) 955-1690 2 SY10E416 SY100E416 Micrel, Inc. DC ELECTRICAL CHARACTERISTICS VEE = VEE (Min.) to VEE (Max.); VCC = VCCO = GND TA = 0°C Symbol VBB TA = +25°C Min. Typ. Output Reference Voltage 10E 100E –1.38 –1.38 — — — — 150 — — 150 — — 135 135 162 162 — — 135 135 50 — — 50 –1.5 — 0 –1.5 IIH Input HIGH Current IEE Power Supply Current 10E 100E VPP (DC) Input Sensitivity VCMR Common Mode Range Max. Min. –1.27 –1.35 –1.26 –1.38 Typ. TA = +85°C Parameter — — Max. Min. –1.25 –1.31 –1.26 –1.38 Typ. Max. Unit Condition V — µA — mA — — — –1.19 –1.26 — — 150 162 162 — — 135 155 162 186 — — 50 — — mV 1 — 0 –1.5 — 0 V 2 Notes: 1. Differential input voltage required to obtain a full ECL swing on the outputs. 2. VCMR is referenced to the most positive side of the differential input signal. Normal operation is obtained when the input signals are within the VCMR range and the input swing is greater than VPP (min.) and <1V. AC ELECTRICAL CHARACTERISTICS VEE = VEE (Min.) to VEE (Max.); VCC = VCCO = GND TA = 0°C Symbol tPD TA = +25°C TA = +85°C Parameter Min. Typ. Max. Min. Typ. Max. Min. Typ. Max. Unit Propagation Delay to Output D (Diff) D (SE) 250 200 350 350 500 550 250 200 350 350 500 550 250 200 350 350 500 550 — 50 — — 50 — — 50 — Condition ps — ps 1 ps 2 tskew Within-Device Skew tskew Duty Cycle Skew, tPLH–tPHL VPP (AC) Minimum Input Swing 150 — — 150 — — 150 — — mV 3 tr tf Rise/Fall Time 20–80% 100 200 350 100 200 350 100 200 350 ps — ±10 ±10 ±10 Notes: 1. Within-device skew is defined as identical transitions on similar paths through a device. 2. Duty cycle skew defined only for differential operation when the delays are measured from the cross point of the inputs to the cross point of the outputs. 3. Minimum input swing for which AC parameters are guaranteed. M9999-032206 [email protected] or (408) 955-1690 3 SY10E416 SY100E416 Micrel, Inc. 28-PIN PLCC (J28-1) Rev. 03 MICREL, INC. 2180 FORTUNE DRIVE SAN JOSE, CA 95131 TEL + 1 (408) 944-0800 FAX + 1 (408) 474-1000 WEB USA http://www.micrel.com The information furnished by Micrel in this data sheet is believed to be accurate and reliable. However, no responsibility is assumed by Micrel for its use. Micrel reserves the right to change circuitry and specifications at any time without notification to the customer. Micrel Products are not designed or authorized for use as components in life support appliances, devices or systems where malfunction of a product can reasonably be expected to result in personal injury. Life support devices or systems are devices or systems that (a) are intended for surgical implant into the body or (b) support or sustain life, and whose failure to perform can be reasonably expected to result in a significant injury to the user. A Purchaser’s use or sale of Micrel Products for use in life support appliances, devices or systems is at Purchaser’s own risk and Purchaser agrees to fully indemnify Micrel for any damages resulting from such use or sale. © 2006 Micrel, Incorporated. M9999-032206 [email protected] or (408) 955-1690 4