SY89228U 1GHz Precision, LVPECL ÷3, ÷5 Clock Divider with Fail-Safe Input and Internal Termination General Description The SY89228U is a precision, low jitter 1GHz ÷3, ÷5 clock divider with an LVPECL output. A unique FailSafe Input (FSI) protection prevents metastable output conditions when the input clock voltage swing drops significantly below 100mV or input is removed. The differential input includes Micrel’s unique, 3-pin internal termination architecture that allows the input to interface to any differential signal (AC- or DCcoupled) as small as 100mV (200mVPP) without any level shifting or termination resistor networks in the signal path. The outputs are 800mV, 100Kcompatible LVPECL with fast rise/fall times guaranteed to be less than 270ps. The SY89228U operates from a 2.5V ±5% or 3.3V ±10% supply and is guaranteed over the full industrial temperature range of –40°C to +85°C. The SY89228U is part of Micrel’s high-speed, Precision Edge® product line. All support documentation can be found on Micrel’s web site at: www.micrel.com. Block Diagram Precision Edge® Features • Accepts a high-speed input and provides a precision ÷3 and ÷5 sub-rate, LVPECL output • Fail-Safe Input – Prevents oscillations when input is invalid • Guaranteed AC performance over temperature and supply voltage: – DC-to >1.0GHz throughput – < 1500ps Propagation Delay (In-to-Q) – < 270ps Rise/Fall times • Ultra-low jitter design: – <1psRMS random jitter – <1psRMS cycle-to-cycle jitter – <10psPP total jitter (clock) – <0.7psRMS MUX crosstalk induced jitter • Unique patented internal termination and VT pin accepts DC- and AC-coupled inputs (CML, PECL, LVDS) • Wide input voltage range VCC to GND • 800mV LVPECL output • 46% to 54% Duty Cycle(÷ 3) • 47% to 53% Duty Cycle(÷ 5) • 2.5V ±5% or 3.3V ±10% supply voltage • -40°C to +85°C industrial temperature range • Available in 16-pin (3mm x 3mm) MLF® package Applications • Fail-safe clock protection Markets • • • • LAN/WAN Enterprise servers ATE Test and measurement Precision Edge is a registered trademark of Micrel, Inc. MLF and MicroLeadFrame are registered trademarks of Amkor Technology. Micrel Inc. • 2180 Fortune Drive • San Jose, CA 95131 • USA • tel +1 (408) 944-0800 • fax + 1 (408) 474-1000 • http://www.micrel.com August 2007 M9999-080707-A [email protected] or (408) 955-1690 Micrel, Inc. SY89228U Ordering Information(1) Package Marking Lead Finish Industrial 228U with Pb-Free bar-line Indicator NiPdAu Pb-Free Industrial 228U with Pb-Free bar-line Indicator NiPdAu Pb-Free Part Number Package Type Operating Range SY89228UMG MLF-16 SY89228UMGTR(2) MLF-16 Notes: 1. Contact factory for die availability. Dice are guaranteed at TA = 25°C, DC Electricals Only. 2. Tape and Reel. Pin Configuration 16-Pin MLF® (MLF-16) August 2007 2 M9999-080707-A [email protected] or (408) 955-1690 Micrel, Inc. SY89228U Pin Description Pin Number 1, 4 2 Pin Name IN, /IN VT Pin Function Differential Input: This input pair is the differential signal input to the device, which accepts AC- or DC-coupled signal as small as 100mV. The input internally terminates to a VT pin through 50Ω and has level shifting resistors of 3.72 kΩ to VCC. This allows a wide input voltage range from VCC to GND. See Figure 3a, Simplified Differential Input Stage for details. Note that this input will default to a valid (either HIGH or LOW) state if left open. See “Input Interface Applications” subsection. Input Termination Center-Tap: Each side of the differential input pair terminates to the VT pin. The VT pin provides a center-tap for the input (IN, /IN) to a termination network for maximum interface flexibility. See “Input Interface Applications” subsection for more details. VREF-AC Reference Voltage: This output biases to VCC–1.2V. It is used for AC-coupling inputs IN and /IN. Connect VREF-AC directly to the VT pin. Bypass with 0.01µF low ESR capacitor to VCC. Due to limited drive capability, the VREF-AC pin is only intended to drive its respective VT pin. Maximum sink/source current is ±0.5mA. See “Input Interface Applications” subsection. EN Single-ended Input: This TTL/CMOS-compatible input disables and enables the output. It is internally connected to a 25kΩ pull-up resistor and will default to a logic HIGH state if left open. When disabled, Q goes LOW and /Q goes HIGH. EN being synchronous, outputs will be enabled/disabled after a rising and a falling edge of the input clock. VTH = VCC/2. 6 /MR Single-ended Input: This TTL/CMOS-compatible input, when pulled LOW, asynchronously sets Q output LOW and /Q output HIGH. Note that this input is internally connected to a 25kΩ pull-up resistor and will default to logic HIGH state if left open. VTH = VCC/2. 7 NC No Connect 8, 13 VCC Positive Power Supply: Bypass with 0.1µF in parallel with 0.01µF low ESR capacitors as close to the VCC pins as possible. 12, 9 Q, /Q Differential Output: The LVPECL output swing is typically 800mV and is terminated with 50Ω to VCC-2V. See the “Truth Table” below for the logic function. 10, 11, 14,15 GND, Exposed Pad Ground: Ground and exposed pad must be connected to a ground plane that is the same potential as the ground pins. DIV_SEL Single-ended Input: This TTL/CMOS-compatible input selects divide-by-3 when pulled LOW and divide-by-5 when pulled HIGH. Note that this input is internally connected to a 25kΩ pull-up resistor and will default to logic HIGH state if left open. VTH = VCC/2. 3 5 16 Truth Table Inputs August 2007 Outputs DIV_SEL EN /MR Q /Q X X 0 0 1 0 1 1 ÷3 ÷3 1 1 1 ÷5 ÷5 X 0 1 0 1 3 M9999-080707-A [email protected] or (408) 955-1690 Micrel, Inc. SY89228U Absolute Maximum Ratings(1) Operating Ratings(2) Supply Voltage (VCC) ..........................–0.5V to +4.0V Input Voltage (VIN) ..................................–0.5V to VCC LVPECL Output Current (IOUT).................................... Continuous ................................................. 50mA Surge........................................................ 100mA Current (VT) Source or sink current on VT pin…………±100mA Input Current Source or sink current on (IN, /IN) ........... ±50mA Current (VREF-AC) Source/Sink Current on VREF-AC(4) ............ ±0.5mA Maximum Operating Junction Temperature…..125°C Lead Temperature (soldering, 20 sec.) ..........+260°C Storage Temperature (Ts)..................–65°C to 150°C Supply Voltage (VCC).................. +2.375V to +2.625V ......................................................+3.0V to +3.6V Ambient Temperature (TA)................ –40°C to +85°C Package Thermal Resistance (3) MLF® (θ JA) Still-Air ..................................................... 75°C/W MLF® (ψ JB) Junction-to-Board………………………….33°C/W DC Electrical Characteristics(5) TA = –40°C to +85°C, unless otherwise stated. Symbol Parameter VCC Power Supply Condition Min Typ Max Units 2.375 3.0 2.5 3.3 2.625 3.6 V V ICC Power Supply Current 40 55 mA RIN Input Resistance (IN-to-VT) No load, max VCC 45 50 55 Ω RDIFF_IN Differential Input Resistance (IN-to-/IN) 90 100 110 Ω VIH Input High Voltage (IN, /IN) 1.2 VCC V VIL Input Low Voltage (IN, /IN) 0 VIH–0.1 V VIN Input Voltage Swing (IN, /IN) See Figure 2a. Note 6. 0.1 VCC V VDIFF_IN Differential Input Voltage Swing |IN-/IN| See Figure 2b. 0.2 VIN_FSI Input Voltage Threshold that Triggers FSI VREF-AC Output Reference Voltage VT_IN Voltage from Input to VT VCC–1.3 V 30 100 mV VCC–1.2 VCC–1.1 V 1.8 V Notes: 1. Permanent device damage may occur if absolute maximum ratings are exceeded. This is a stress rating only and functional operation is not implied at conditions other than those detailed in the operational sections of this data sheet. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. 2. The data sheet limits are not guaranteed if the device is operated beyond the operating ratings. 3. Package thermal resistance assumes exposed pad is soldered (or equivalent) to the devices most negative potential on the PCB. θJA and ψJB values are determined for a 4-layer board in still air unless otherwise stated. 4. Due to limited drive capability use for input of the same package only. 5. The circuit is designed to meet the DC specifications shown in the above table after thermal equilibrium has been established. 6. VIN (max) is specified when VT is floating. August 2007 4 M9999-080707-A [email protected] or (408) 955-1690 Micrel, Inc. SY89228U LVPECL Outputs DC Electrical Characteristics(7) VCC = 2.5V ±5% or 3.3V ±10%; RL = 50Ω to VCC-2V; TA = –40°C to + 85°C, unless otherwise stated. Symbol Parameter Max Units VOH Output HIGH Voltage Q, /Q Condition VCC-1.145 Min Typ VCC-0.895 V VOL Output LOW Voltage Q, /Q VCC-1.945 VCC-1.695 V VOUT Output Voltage Swing Q, /Q See Figure 2a. 550 800 950 mV VDIFF_OUT Differential Output Voltage Swing Q, /Q See Figure 2b. 1100 1600 mV LVTTL/CMOS DC Electrical Characteristics(7) VCC = 2.5V ±5% or 3.3V ±10%; TA = –40°C to + 85°C, unless otherwise stated. Symbol Parameter Condition Min VIH Input HIGH Voltage VIL Input LOW Voltage IIH Input HIGH Current -125 IIL Input LOW Current -300 Typ Max 2.0 Units V 0.8 V 30 µA µA Note: 7. The circuit is designed to meet the DC specifications shown in the above table after thermal equilibrium has been established. August 2007 5 M9999-080707-A [email protected] or (408) 955-1690 Micrel, Inc. SY89228U AC Electrical Characteristics(8) VCC = 2.5V ±5% or 3.3V ±10%; RL = 50Ω to VCC-2V; TA = –40°C to + 85°C, unless otherwise stated. Symbol Parameter Condition Min Typ fMAX Maximum Input Operating Frequency VOUT ≥ 200mV 1.0 1.5 Max Units GHz tw Minimum Pulse Width IN, /IN 400 tpd Differential Propagation Delay 100mV < VIN ≤ 200mV, Note 9 900 1150 1500 ps ps 800 1050 1400 ps 350 570 850 ps In-to-Q In-to-Q 200mV < VIN ≤ 800mV, Note 9 /MR(H-L)-to-Q tRR Reset Recovery Time tS EN Set-up Time EN-to-IN tH EN Hold Time IN-to-EN tskew Part-to-Part Skew tJITTER Clock tr, tf /MR(L-H)-to-IN 300 ps Note 10 300 ps Note 10 800 ps Note 10 450 ps Random Jitter Note 11 1 psRMS Cycle-to-Cycle Jitter Note 12 1 psRMS Total Jitter Note 13 10 psPP Output Rise/Fall Time (20% to 80%) At full output swing. 100 270 ps Output Duty Cycle(÷ 3) Duty Cycle(input): 50%; f ≤1GHz; Note 14 46 54 % Output Duty Cycle(÷ 5) Duty Cycle(input): 50%; f ≤1GHz; 47 53 % Note 14 Notes: 8. High-frequency AC-parameters are guaranteed by design and characterization. 9. The propagation delay is function of the rise and fall times at IN. Input tr / tf ≤ 300ps (20% to 80%). See “Typical Operating Characteristics” for details. 10. Set-up and hold times apply to synchronous applications that intend to enable/disable before the next clock cycle. For asynchronous applications, set-up and hold do not apply. 11. Random Jitter is measured with a K28.7 character pattern, measured at <fMAX. 12. Cycle-to-Cycle Jitter definition: the variation of periods between adjacent cycles, Tn – Tn-1 where T is the time between rising edges of the output signal. 12 13. Total Jitter definition: with an ideal clock input of frequency <fMAX, no more than one output edge in 10 output edges will deviate by more than the specified peak-to-peak jitter value. 14. For Input Duty Cycle different from 50%, see “Output Duty Cycle Equation” in “Functional Description” subsection. August 2007 6 M9999-080707-A [email protected] or (408) 955-1690 Micrel, Inc. SY89228U Functional Description Enable (EN) EN is a synchronous TTL/CMOS-compatible input that enables/disables the outputs based on the input to this pin. Internal 25kΩ pull-up resistor defaults the input to logic HIGH if left open. Input switching threshold is VCC/2. The Enable function operates as follows: Fail-Safe Input (FSI) The input includes a special failsafe circuit to sense the amplitude of the input signal and to latch the outputs when there is no input signal present, or when the amplitude of the input signal drops sufficiently below 100mVPK (200mVPP), typically 30mVPK. Maximum frequency of the SY89228U is limited by the FSI function. Refer to Figure 1b. 1. The enable/disable function is synchronous so that the clock outputs will be enabled or disabled following a rising and a falling edge of the input clock when switching from EN = LOW to EN = HIGH. However, when switching from EN = HIGH to EN = LOW, the clock outputs will be disabled following an input clock rising edge and an output clock falling edge. 2. The enable/disable function always guarantees the full pulse width at the output before the clock outputs are disabled, non-depending on the divider ratio. Refer to Figure 1c for examples. Input Clock Failure Case If the input clock fails to a floating, static, or extremely low signal swing, the FSI function will eliminate a metastable condition and guarantee a stable output signal. No ringing and no undetermined state will occur at the output under these conditions. Note that the FSI function will not prevent duty cycle distortion in case of a slowly deteriorating (but still toggling) input signal as it nears the FSI threshold (typically, 30mV). Due to the FSI function, the propagation delay will depend on rise and fall time of the input signal and on its amplitude. See “Typical Operating Characteristics” for detailed information. Output Duty Cycle Equation For a non 50% input, derate the spec by: For Divide by 3: 1+ (0.5 - Divider Operation The divider operation uses both the rising and falling edge of the input clock. For divide by 3, the falling edge of the second input clock cycle will determine the falling edge of the output. For divide by 5, the falling edge of the third input clock cycle. Refer to Figure 1d. X 100 ) x100, in % 3 For Divide by 5: X 100 ) x100, in % (0.5 5 X = input Duty Cycle, in % 2+ Example: if a 45% input duty cycle is applied or X=45, in divide by 3 mode, the spec would expand by 1.67% to 44.3%-55.7% August 2007 7 M9999-080707-A [email protected] or (408) 955-1690 Micrel, Inc. SY89228U Timing Diagrams Figure 1a. Propagation Delay Figure 1b. Fail-Safe Feature August 2007 8 M9999-080707-A [email protected] or (408) 955-1690 Micrel, Inc. SY89228U Figure 1c. Enable Output Timing Diagram Examples (divide by 3) August 2007 9 M9999-080707-A [email protected] or (408) 955-1690 Micrel, Inc. SY89228U Figure 1d. Divider Operation Timing Diagram August 2007 10 M9999-080707-A [email protected] or (408) 955-1690 Micrel, Inc. SY89228U Typical Operating Characteristics VCC = 3.3V, GND = 0V, VIN = 200mV, tr / tf ≤ 300ps, RL = 50Ω to VCC–2V; TA = 25°C, unless otherwise stated. August 2007 11 M9999-080707-A [email protected] or (408) 955-1690 Micrel, Inc. SY89228U Functional Characteristics VCC = 3.3V, GND = 0V, VIN = 100mV, Q = Divide by 3, tr/tf ≤ 300ps, RL = 50Ω to VCC-2V; TA = 25°C, unless otherwise stated. August 2007 12 M9999-080707-A [email protected] or (408) 955-1690 Micrel, Inc. SY89228U Single-Ended and Differential Swings Figure 2b. Differential Voltage Swing Figure 2a. Single-Ended Voltage Swing Input and Output Stages Figure 3a. Simplified Differential Input Stage August 2007 Figure 3b. Simplified Differential Output Stage 13 M9999-080707-A [email protected] or (408) 955-1690 Micrel, Inc. SY89228U Input Interface Applications Option: may connect VT to VCC Figure 4a. LVPECL Interface (DC-Coupled) Figure 4b. LVPECL Interface (AC-Coupled) Figure 4d. CML Interface (AC-Coupled) Figure 4e. LVDS Interface (DC-Coupled) August 2007 14 Figure 4c. CML Interface (DC-Coupled) M9999-080707-A [email protected] or (408) 955-1690 Micrel, Inc. SY89228U PECL Output Interface Applications PECL has high input impedance, very low output impedance (open emitter), and a small signal swing which results in low EMI. PECL is ideal for driving 50Ω- and 100Ω-controlled impedance transmission lines. There are several techniques for terminating the PECL output: parallel termination-thevenin equivalent, parallel termination (3-resistor), and ACcoupled termination. Unused output pairs may be left floating. However, single-ended outputs must be terminated, or balanced. Figure 5b. Parallel Termination (3-Resistor) Figure 5a. Parallel Termination-Thevenin Equivalent Related Product and Support Documentation Part Number Function Datasheet Link SY89229U 1GHz Precision, LVDS ÷3, ÷5 Clock Divider with Fail Safe Input and Internal Termination http://www.micrel.com/_PDF/HBW/sy89229u.pdf SY89230U 3.2GHz Precision, LVPECL ÷3, ÷5 Clock Divider http://www.micrel.com/_PDF/HBW/sy89230u.pdf SY89231U 3.2GHz Precision, LVDS ÷3, ÷5 Clock Divider http://www.micrel.com/_PDF/HBW/sy89231u.pdf MLF® Application Note www.amkor.com/products/notes_papers/MLFAppNote.pdf August 2007 15 M9999-080707-A [email protected] or (408) 955-1690 Micrel, Inc. SY89228U Package Information 16-Pin MicroLeadFrame® (MLF-16) Packages Notes: 1. Package meets Level 2 Moisture Sensitivity Classification. 2. All parts are dry-packed before shipment. 3. Exposed pad must be soldered to a ground for proper thermal management. MICREL, INC. 2180 FORTUNE DRIVE SAN JOSE, CA 95131 USA TEL +1 (408) 944-0800 FAX +1 (408) 474-1000 WEB http:/www.micrel.com The information furnished by Micrel in this data sheet is believed to be accurate and reliable. However, no responsibility is assumed by Micrel for its use. Micrel reserves the right to change circuitry and specifications at any time without notification to the customer. Micrel Products are not designed or authorized for use as components in life support appliances, devices or systems where malfunction of a product can reasonably be expected to result in personal injury. Life support devices or systems are devices or systems that (a) are intended for surgical implant into the body or (b) support or sustain life, and whose failure to perform can be reasonably expected to result in a significant injury to the user. A Purchaser’s use or sale of Micrel Products for use in life support appliances, devices or systems is a Purchaser’s own risk and Purchaser agrees to fully indemnify Micrel for any damages resulting from such use or sale. © 2007 Micrel, Inc. August 2007 16 M9999-080707-A [email protected] or (408) 955-1690