NICHICON UWT0G220MCL

ALUMINUM ELECTROLYTIC CAPACITORS
WT
Chip Type, Wide Temperature Range
series
Chip type operating over wide temperature range of to – 55 ~ +105°C.
Designed for surface mounting on high density PC board.
Applicable to automatic mounting machine using carrier tape.
Adapted to the RoHS directive (2002/95/EC).
WZ
High
Temperature
Reflow
WF
Low
impeadance
UT
Long Life
WT
Smaller
ZT
Specifications
Item
Performance Characteristics
Category Temperature Range
– 55 ~ +105°C
Rated Voltage Range
4 ~ 50V
Rated Capacitance Range
0.1 ~ 1500µF
Capacitance Tolerance
±20% at 120Hz, 20°C
Leakage Current
After 2 minutes' application of rated voltage, leakage current is not more than 0.01CV or 3 (µA) , whichever is greater.
Measurement frequency : 120Hz, Temperature : 20°C
tan δ
Rated voltage (V)
tan δ (MAX.)
4
0.40
6.3
0.30
10
0.24
16
0.20
25
0.16
35
0.14
50
0.14
Measurement frequency : 120Hz
Stability at Low Temperature
Rated voltage (V)
Z– 25°C / Z+20°C
Impedance ratio
Z– 40°C / Z+20°C
ZT / Z20 (MAX.)
After 1000 hours' application of rated voltage
at 105°C, capacitors meet the characteristic
requirements listed at right.
Endurance
Shelf Life
Resistance to soldering
heat
4
7
15
6.3
4
8
10
3
8
16
2
4
25
2
4
35
2
3
50
2
3
Within ±25% of initial value for capacitors of φ3mm unit, and 16V or less.
Within ±20% of initial value for capacitors of 25V or more.
tan δ
200% or less of initial specified value
Leakage current Initial specified value or less
Capacitance
change
After storing the capacitors under no load at 105°C for 1000 hours, and after performing voltage treatment based on JIS C 5101-4
clause 4.1 at 20°C, they will meet the specified value for endurance characteristics listed above.
The capacitors shall be kept on the hot plate maintained at 250°C
Capacitance change Within ±10% of initial value
for 30 seconds. After removing from the hot plate and restored
tan δ
Initial specified value or less
at room temperature, they meet the characteristic requirements
Initial specified value or less
Leakage current
listed at right.
Black print on the case top.
Marking
Type numbering system (Example : 16V 10µF)
Chip Type
(f3 ~ f8 ´ 5.4 )
Positive
Lot No.
E
L +0.1
Ð0.2
(L±0.3) 3
H
3 Apply to f6.3 ´ 5.8, f6.3 ´ 7.7
2
0.5 MAX.
E
H
Negative
1. Voltage mark for 6.3V is 6V . In case of marking for f3 units, ÒVÓ for rated
voltage is omitted.
2. In case of marking for f3 units. Lot No is expressed by a digit (month code).
(mm)
D´L
3 ´ 5.4 4 ´ 5.4 5 ´ 5.4 6.3 ´ 5.4 6.3 ´ 5.8 6.3 ´ 7.7 8 ´ 5.4 8 ´ 10 10 ´ 10
A
B
C
E
L
H
1.5
3.3
3.3
0.8
5.4
0.5 ~ 0.8
f
A±0.2 A±0.2
L±0.5
Pressure relief vent
C±0.2
B±0.2
D±0.5
Plastic platform
0.3 MAX.
f
A2P
100
35V
fD
code
3 ~ 8 (5.4L) GB
6.3 ~ 10 (L 5.8) GS
Package code
Size code
fD
code
Configuration
3
2
fD
code
4 ~ 10 1
3 ~ 8 (L 7.7) CL
8 ~ 10 (L = 10) NL
Positive
1
Voltage
Lot No.
Capacitance tolerance (±20%)
Rated Capacitance (10µF)
Rated voltage (16V)
Series name
Type
Negative
(f8 ´ 10, f10 ´ 10 )
Capacitance
105¡C Marking
Trade mark
1 2 3 4 5 6 7 8 9 10 11 12 13 14
UWT 1 C 1 0 0 MC L 1 G B
0.5 MAX.
C±0.2
A±0.2 A±0.2
D±0.5
Plastic platform
0.3 MAX.
f
A2P
10
16V
1
Voltage
B±0.2
Capacitance
105¡C Marking
1.8
4.3
4.3
1.0
5.4
0.5 ~ 0.8
2.1
5.3
5.3
1.3
5.4
0.5 ~ 0.8
2.4
6.6
6.6
2.2
5.4
0.5 ~ 0.8
2.4
6.6
6.6
2.2
5.8
0.5 ~ 0.8
2.4
6.6
6.6
2.2
7.7
0.5 ~ 0.8
3.3
8.3
8.3
2.3
5.4
0.5 ~ 0.8
2.9
8.3
8.3
3.1
10
0.8 ~ 1.1
3.2
10.3
10.3
4.5
10
0.8 ~ 1.1
Dimension table in next page.
CAT.8100V
ALUMINUM ELECTROLYTIC CAPACITORS
WT
series
Dimensions
V
Cap. (µF)
Code
4
0G
6.3
0J
10
1A
16
1C
25
1E
35
1V
50
1H
0.1
0R1
4 × 5.4 (3)
1.0
0.22
R22
4 × 5.4 (3)
2.6
0.33
R33
4 × 5.4 (3)
3.2
0.47
R47
4 × 5.4 (3)
3.8
1
010
4 × 5.4 (3) 6.3 (5.9)
2.2
2R2
3 × 5.4
7.5
4 × 5.4 (3) 11 (9)
3.3
3R3
3 × 5.4
9
4 × 5.4
14
4.7
4R7
4 × 5.4 (3) 13 (10)
4 × 5.4
15
5 × 5.4
19
5 × 5.4
23
5 × 5.4
25
6.3 × 5.4
30
42
8 × 5.4
4 × 5.4 (3) 18 (14)
10
100
22
220
4 × 5.4
22
4 × 5.4
22
5 × 5.4
27
5 × 5.4
30
6.3 × 5.4
38
6.3 × 5.4
33
330
5 × 5.4
30
5 × 5.4
30
5 × 5.4
35
6.3 × 5.4
40
6.3 × 5.4
48
8 × 5.4
47
470
5 × 5.4
36
5 × 5.4
36
6.3 × 5.4
46
6.3 × 5.4
50
8 × 5.4
100
101 6.3 × 5.4
60
6.3 × 5.4
60
6.3 × 5.4
60
6.3 × 5.4
60
6.3 × 7.7
150
151 6.3 × 5.8
86
6.3 × 5.8
86
220
221
330
331 6.3 × 7.7
105
6.3 × 7.7
105
470
471
8 × 10
210
8 × 10
680
681
8 × 10
210
8 × 10
1000
102
8 × 10
230
1500
152
10 × 10
310
8 × 5.4
102 (91)
59 (52) 6.3 × 7.7
51 (45)
60
66 (59) 6.3 × 5.8
63
6.3 × 7.7
63
91
6.3 × 7.7
84
8 × 10
140
6.3 × 5.8
86
6.3 × 7.7
95
8 × 10
140
8 × 10
155
10 × 10
180
102 (91) 6.3 × 7.7
105
6.3 × 7.7
105
8 × 10
155
8 × 10
190
10 × 10
220
8 × 10
195
8 × 10
195
8 × 10
190
10 × 10
300
210
8 × 10
210
8 × 10
230
10 × 10
300
210
10 × 10
310
10 × 10
310
8 × 10
230
10 × 10
310
10 × 10
310
8 × 5.4
( ) is also available with φ3mm upon request. In such a case, 2 will be put at 12th digit of type numbering system.
Size φ6.3 × 5.8 is available for capacitors marked. " " In such a case, 6 will be put at 12th digit of type numbering system.
Case size Rated
φ D × L (mm) ripple
Rated Ripple (mArms) at 105°C 120Hz
Frequency coefficient of rated ripple current
Frequency
Coefficient
50 Hz
0.70
120 Hz
1.00
300 Hz
1.17
1 kHz
1.36
10 kHz~
1.50
Taping specifications are given in page 24.
Recommended land size, soldering by reflow are given
in page 25, 26.
Please select UX(p.74), UJ(p.76) series if high C/V
products are reqired.
Please refer to page 3 for the minimum order quantity.
CAT.8100V