NICHICON UWD1C151MCL

ALUMINUM ELECTROLYTIC CAPACITORS
WD
Chip Type, Low Impedance
High Temperature (260°C) Reflow
series
Corresponding with 260°C peak reflow soldering
Recomended reflow condition : 260°C peak 5 sec. 230°C over 60 sec.
2 times (φ10 × 10, : 1 time)
Chip type, low impedance temperature range up to +105°C.
WD
Designed for surface mounting on high density PC board.
Applicable to automatic mounting machine using carrier tape.
Adapted to the RoHS directive (2002/95/EC).
High
Temperature
Reflow
UD
Specifications
Item
Performance Characteristics
Category Temperature Range
– 55 ~ +105°C
Rated Voltage Range
6.3 ~ 50V
Rated Capacitance Range
1 ~ 1500µF
Capacitance Tolerance
± 20% at 120Hz, 20°C
Leakage Current
After 2 minutes' application of rated voltage, leakage current is not more than 0.01 CV or 3 (µA), whichever is greater.
Measurement frequency : 120Hz, Temperature : 20°C
Rated voltage (V)
6.3
10
16
25
35
50
tan δ (MAX.)
0.26 (0.28) 0.20 (0.24) 0.16 (0.20) 0.14 (0.16) 0.12 (0.14) 0.12 (0.14)
tan δ
(
) is φ8 over
Measurement frequency : 120Hz
Stability at Low Temperature
6.3
3
5
Rated voltage (V)
Z– 25°C / Z+20°C
Z– 55°C / Z+20°C
Impedance ratio
ZT / Z20 (MAX.)
After 5000 hours' (2000 hours for φD 6.3)
application of rated voltage at 105°C , capacitors
meet the characteristic requirements listed at
right.
Endurance
10
2
4
16
2
4
25
2
3
35
2
3
Capacitance change
tan δ
Leakage current
50
2
3
Within ±30% of initial value
200% or less of initial specified value
Initial specified value or less
After storing the capacitors under no load at 105°C for 1000 hours, and after performing voltage treatment based on JIS C 5101-4
clause 4.1 at 20°C, they will meet the specified value for endurance characteristics listed above.
The capacitors shall be kept on the hot plate maintained at 250°C
Capacitance change Within ±10% of initial value
for 30 seconds. After removing from the hot plate and restored
tan δ
Initial specified value or less
at room temperature, they meet the characteristic requirements
Leakage current
Initial specified value or less
listed at right.
Shelf Life
Resistance to soldering
heat
Black print on the case top.
Marking
Type numbering system (Example : 16V 22µF)
Chip Type
(φ4 ~ φ6.3)
Plastic platform
0.3 MAX.
1
2
3
4
5
6
7
8
9
10 11 12 13 14
A±0.2
UWD 1 C 2 2 0 M C L 1 G S
Package code
Configuration
A±0.2
E
L±0.3
Capacitance
Lot No.
C±0.2
B±0.2
N2
33C
WD
φD±0.5
Series
Voltage (C:16V)
0.5 MAX.
Positive
H
Capacitance tolerance (±20%)
Rated Capacitance (22 µF)
Negative
Rated voltage (16V)
Series name
Type
(φ8 ~ φ10)
Lot No.
E
L±0.5
Capacitance
φD×L
A±0.2 A±0.2
C±0.2
B±0.2
N2
100V
WD
Trade mark
Plastic platform
0.3 MAX.
Series
φD±0.5
Voltage (V:35V)
0.5 MAX.
Positive
Negative
A
B
C
E
L
H
(mm)
4 × 5.8
5 × 5.8
6.3 × 5.8
6.3 × 7.7
8 × 10
10 × 10
1.8
4.3
4.3
1.0
5.8
0.5 ~ 0.8
2.1
5.3
5.3
1.3
5.8
0.5 ~ 0.8
2.4
6.6
6.6
2.2
5.8
0.5 ~ 0.8
2.4
6.6
6.6
2.2
7.7
0.5 ~ 0.8
2.9
8.3
8.3
3.1
10
0.8 ~ 1.1
3.2
10.3
10.3
4.5
10
0.8 ~ 1.1
H
Voltage
V
6.3
Code
j
10
A
16
C
25
E
35
V
50
H
Dimension table in next page.
CAT.8100V
ALUMINUM ELECTROLYTIC CAPACITORS
WD
series
Dimensions
Cap.
(µF)
V
6.3
10
16
25
35
50
Code
0J
1A
1C
1E
1V
1H
1
010
4 × 5.8
5.00
30
2.2
2R2
4 × 5.8
5.00
30
3.3
3R3
4 × 5.8
5.00
30
4.7
4R7
10
100
15
150
22
220
27
270
4 × 5.8
1.80
33
330
5 × 5.8
47
470
56
4 × 5.8
1.80
80
5 × 5.8
1.52
85
4 × 5.8
1.80
80
5 × 5.8
0.76
150
6.3 × 5.8
0.88
165
4 × 5.8
1.80
80
5 × 5.8
0.76
150
5 × 5.8
0.76
150
6.3 × 5.8
0.88
165
4 × 5.8
1.80
80
5 × 5.8
0.76
150
5 × 5.8
0.76
150
5 × 5.8
0.76
150
6.3 × 5.8
0.88
165
80
5 × 5.8
0.76
150
5 × 5.8
0.76
150
6.3 × 5.8
0.44
230
6.3 × 5.8
0.44
230
6.3 × 7.7
0.68
185
0.76
150
5 × 5.8
0.76
150
6.3 × 5.8
0.44
230
6.3 × 5.8
0.44
230
6.3 × 5.8
0.44
230
6.3 × 7.7
0.68
185
5 × 5.8
0.76
150
6.3 × 5.8
0.44
230
6.3 × 5.8
0.44
230
6.3 × 5.8
0.44
230
6.3 × 5.8
0.44
230
6.3 × 7.7
0.68
185
560
5 × 5.8
0.76
150
6.3 × 5.8
0.44
230
6.3 × 5.8
0.44
230
6.3 × 5.8
0.44
230
6.3 × 7.7
0.34
280
8 × 10
0.34
300
68
680
6.3 × 5.8
0.44
230
6.3 × 5.8
0.44
230
6.3 × 5.8
0.44
230
6.3 × 5.8
0.44
230
6.3 × 7.7
0.34
280
8 × 10
0.34
300
100
101
6.3 × 5.8
0.44
230
6.3 × 5.8
0.44
230
6.3 × 5.8
0.44
230
6.3 × 7.7
0.34
280
8 × 10
0.17
450
8 × 10
0.34
300
150
151
6.3 × 5.8
0.44
230
6.3 × 5.8
0.44
230
6.3 × 7.7
0.34
280
8 × 10
0.17
450
8 × 10
0.17
450
10 × 10
0.18
670
220
221
6.3 × 5.8
0.44
230
6.3 × 7.7
0.34
280
6.3 × 7.7
0.34
280
8 × 10
0.17
450
10 × 10
0.09
670
10 × 10
0.18
670
330
331
6.3 × 7.7
0.34
280
8 × 10
0.17
450
8 × 10
0.17
450
10 × 10
0.09
670
10 × 10
0.09
670
470
471
8 × 10
0.17
450
8 × 10
0.17
450
8 × 10
0.17
450
10 × 10
0.09
670
680
681
8 × 10
0.17
450
10 × 10
0.09
670
10 × 10
0.09
670
1000
102
10 × 10
0.09
670
10 × 10
0.09
670
1500
152
10 × 10
0.09
670
Impedance
Rated
ripple
Case size
φ D × L (mm)
Max. Impedance (Ω) at 20°C 100kHz,
Rated Ripple (mArms) at 105°C 100kHz
Frequency coefficient of rated ripple current
Frequency
Coefficient
50 Hz
0.35
120 Hz
0.50
300 Hz
0.64
1 kHz
0.83
10 kHz~
1.00
Taping specifications are given in page 24.
Recommended land size, soldering by reflow are given
in page 25, 26.
Please refer to page 3 for the minimum order quantity.
CAT.8100V