PRELIMINARY PRELIMINARY KM641003C CMOS SRAM Document Title 256Kx4 Bit (with OE) High-Speed CMOS Static RAM(5.0V Operating). Revision History Preliminary CCPCCCRCELIMINARY Rev. No. History Draft Data Rev. 0.0 Initial release with Preliminary. Aug. 5. 1998 Preliminary Rev. 1.0 Release to Final Data Sheet. 1.1. Delete Preliminary. Mar. 3. 1999 Final Remark The attached data sheets are prepared and approved by SAMSUNG Electronics. SAMSUNG Electronics CO., LTD. reserve the right to change the specifications. SAMSUNG Electronics will evaluate and reply to your requests and questions on the parameters of this device. If you have any questions, please contact the SAMSUNG branch office near your office, call or contact Headquarters. -1- Revision 1.0 March 1999 PRELIMINARY PRELIMINARY KM641003C CMOS SRAM 256K x 4 Bit (with OE) High-Speed CMOS Static RAM FEATURES GENERAL DESCRIPTION • Fast Access Time 12,15,20ns(Max.) • Low Power Dissipation Standby (TTL) : 30mA(Max.) (CMOS) : 5mA(Max.) Operating KM641003C - 12 : 70mA(Max.) KM641003C - 15 : 68mA(Max.) KM641003C - 20 : 65mA(Max.) • Single 5.0V±10% Power Supply • TTL Compatible Inputs and Outputs • I/O Compatible with 3.3V Device • Fully Static Operation - No Clock or Refresh required • Three State Outputs • Center Power/Ground Pin Configuration • Standard Pin Configuration : KM641003CJ : 32-SOJ-400 The KM641003C is a 1,048,576-bit high-speed Static Random Access Memory organized as 262,144 words by 4 bits. The KM641003C uses 4 common input and output lines and has an output enable pin which operates faster than address access time at read cycle. The device is fabricated using SAMSUNG′s advanced CMOS process and designed for high-speed circuit technology. It is particularly well suited for use in high-density high-speed system applications. The KM641003C is packaged in a 400 mil 32-pin plastic SOJ. Preliminary CCPCCCRCELIMINARY PIN CONFIGURATION (Top View) FUNCTIONAL BLOCK DIAGRAM A0 A1 A2 A3 A4 A5 A6 A7 A8 Row Select Clk Gen. Pre-Charge Circuit Memory Array 512 Rows 512x4 Columns N.C 1 32 A17 A0 2 31 A16 A1 3 30 A15 A2 4 29 A14 A3 5 28 A13 6 27 7 26 I/O4 Vcc 8 Vss 9 24 Vcc I/O2 10 23 I/O3 WE 11 22 A12 A4 12 21 A11 A5 13 20 A10 A6 14 19 A9 A7 15 18 A8 25 Vss SOJ 17 N.C N.C 16 I/O1 ~ I/O4 Data Cont. OE CS I/O1 I/O Circuit & Column Select CLK Gen. PIN FUNCTION A9 A10 A11 A12 A13 A14 A15 A16 A17 Pin Name A0 - A17 CS WE OE WE Write Enable CS Chip Select OE Output Enable I/O1 ~ I/O 4 -2- Pin Function Address Inputs Data Inputs/Outputs VCC Power(+5.0V) VSS Ground N.C No Connection Revision 1.0 March 1999 PRELIMINARY PRELIMINARY KM641003C CMOS SRAM ABSOLUTE MAXIMUM RATINGS* Parameter Voltage on Any Pin Relative to VSS Symbol Rating Unit VIN, VOUT -0.5 to Vcc+0.5V V Preliminary CCPCCCRCELIMINARY Pd 1 Voltage on VCC Supply Relative to VSS Power Dissipation Storage Temperature VCC -0.5 to 7.0 V TSTG -65 to 150 °C TA 0 to 70 °C Operating Temperature W * Stresses greater than those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operating sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. RECOMMENDED DC OPERATING CONDITIONS(TA=0 to 70°C) Parameter Symbol Min Typ Max Unit Supply Voltage VCC 4.5 5.0 5.5 V Ground VSS 0 0 0 V Input High Voltage VIH 2.2 - VCC+0.5** V Input Low Voltage VIL -0.5* - 0.8 V * VIL(Min) = -2.0V a.c (Pulse Width ≤ 8ns) for I ≤ 20mA. ** V IH(Max) = VCC + 2.0V a.c (Pulse Width ≤ 8ns) for I ≤ 20mA. DC AND OPERATING CHARACTERISTICS(TA=0 to 70°C, Vcc=5.0V±10%, unless otherwise specified) Min Max Unit Input Leakage Current Parameter Symbol ILI VIN=VSS to VCC Test Conditions -2 2 µA Output Leakage Current ILO CS=VIH or OE=VIH or WE=VIL VOUT=VSS to VCC -2 2 µA Operating Current ICC Min. Cycle, 100% Duty CS=VIL, VIN=VIH or VIL, IOUT=0mA 12ns - 70 mA 15ns - 68 20ns - 65 ISB Min. Cycle, CS=VIH - 30 ISB1 f=0MHz, CS ≥VCC-0.2V, VIN≥VCC-0.2V or VIN≤0.2V - 5 Output Low Voltage Level VOL IOL=8mA - 0.4 V Output High Voltage Level VOH IOH=-4mA 2.4 - V - 3.95 V Standby Current VOH1* IOH1=-0.1mA mA * VCC=5.0V±5%, Temp.=25°C. CAPACITANCE*(TA=25°C, f=1.0MHz) Symbol Test Conditions MIN Max Unit Input/Output Capacitance Item CI/O VI/O=0V - 8 pF Input Capacitance CIN VIN=0V - 6 pF * Capacitance is sampled and not 100% tested. -3- Revision 1.0 March 1999 PRELIMINARY PRELIMINARY KM641003C CMOS SRAM AC CHARACTERISTICS(TA=0 to 70°C, VCC=5.0V±10%, unless otherwise noted.) TEST CONDITIONS Parameter Value Preliminary CCPCCCRCELIMINARY 3ns Input Pulse Levels 0V to 3V Input Rise and Fall Times Input and Output timing Reference Levels 1.5V Output Loads See below Output Loads(B) for tHZ, tLZ, tWHZ, tOW, tOLZ & tOHZ Output Loads(A) +5.0V RL = 50Ω DOUT VL = 1.5V 480Ω DOUT 30pF* ZO = 50Ω 255Ω 5pF* * Including Scope and Jig Capacitance * Capacitive Load consists of all components of the test environment. READ CYCLE Parameter Symbol KM641003C-12 KM641003C-15 KM641003C-20 Min Max Min Max Min Max Unit Read Cycle Time tRC 12 - 15 - 20 - ns Address Access Time tAA - 12 - 15 - 20 ns Chip Select to Output tCO - 12 - 15 - 20 ns Output Enable to Valid Output tOE - 6 - 7 - 9 ns Chip Enable to Low-Z Output Output Enable to Low-Z Output Chip Disable to High-Z Output tLZ 3 - 3 - 3 - ns tOLZ 0 - 0 - 0 - ns tHZ 0 6 - 7 - 9 ns Output Disable to High-Z Output tOHZ 0 6 0 7 0 9 ns Output Hold from Address Change tOH 3 - 3 - 3 - ns Chip Selection to Power Up Time tPU 0 - 0 - 0 - ns Chip Selection to Power DownTime tPD - 12 - 15 - 20 ns -4- Revision 1.0 March 1999 PRELIMINARY PRELIMINARY KM641003C CMOS SRAM WRITE CYCLE Parameter Symbol KM641003C-12 KM641003C-15 KM641003C-20 Min Min Min Max Max Write Cycle Time tWC 12 Chip Select to End of Write tCW 8 Address Set-up Time tAS 0 - 0 - Address Valid to End of Write tAW 8 - 9 - Write Pulse Width(OE High) tWP 8 - 9 - Max Unit - ns - ns 0 - ns 10 - ns 10 - ns 15 20 Preliminary CCPCCCRCELIMINARY 9 10 Write Pulse Width(OE Low) tWP1 12 - 15 - 20 - ns Write Recovery Time tWR 0 - 0 - 0 - ns Write to Output High-Z tWHZ 0 6 0 7 0 9 ns Data to Write Time Overlap tDW 6 - 7 - 8 - ns Data Hold from Write Time tDH 0 - 0 - 0 - ns End Write to Output Low-Z tOW 3 - 3 - 3 - ns TIMMING DIAGRAMS TIMING WAVEFORM OF READ CYCLE(1) (Address Controlled, CS=OE=VIL , WE=VIH) tRC Address tAA tOH Data Out Valid Data Previous Valid Data TIMING WAVEFORM OF READ CYCLE(2) (WE=VIH) tRC Address tAA tCO CS tHZ(3,4,5) tOHZ tOE OE tOH tOLZ tLZ(4,5) Data out Valid Data VCC ICC Current ISB tPU tPD 50% 50% -5- Revision 1.0 March 1999 PRELIMINARY PRELIMINARY KM641003C CMOS SRAM NOTES(READ CYCLE) 1. WE is high for read cycle. 2. All read cycle timing is referenced from the last valid address to the first transition address. 3. tHZ and tOHZ are defined as the time at which the outputs achieve the open circuit condition and are not referenced to V OH or VOL levels. 4. At any given temperature and voltage condition, tHZ(Max.) is less than tLZ(Min.) both for a given device and from device to device. 5. Transition is measured ±200mV from steady state voltage with Load(B). This parameter is sampled and not 100% tested. 6. Device is continuously selected with CS=VIL. 7. Address valid prior to coincident with CS transition low. 8. For common I/O applications, minimization or elimination of bus contention conditions is necessary during read and write cycle. Preliminary CCPCCCRCELIMINARY TIMING WAVEFORM OF WRITE CYCLE(1) (OE= Clock) tWC Address tWR(5) tAW OE tCW(3) CS tWP(2) tAS(4) WE tDW Data in High-Z tDH Valid Data tOHZ(6) High-Z(8) Data out TIMING WAVEFORM OF WRITE CYCLE(2) (OE=Low Fixed) tWC Address tAW tWR(5) tCW(3) CS tAS(4) tWP1(2) WE tDW Data in High-Z tDH Valid Data tWHZ(6) tOW High-Z(8) Data out -6- (10) (9) Revision 1.0 March 1999 PRELIMINARY PRELIMINARY KM641003C CMOS SRAM TIMING WAVEFORM OF WRITE CYCLE(3) (CS=Controlled) tWC Address Preliminary CCPCCCRCELIMINARY tAW tWR(5) tCW(3) CS tWP(2) tAS(4) WE tDW High-Z Data in Valid Data tLZ High-Z tWHZ(6) High-Z(8) High-Z Data out tDH NOTES(WRITE CYCLE) 1. All write cycle timing is referenced from the last valid address to the first transition address. 2. A write occurs during the overlap of a low CS and WE. A write begins at the latest transition CS going low and WE going low ; A write ends at the earliest transition CS going high or WE going high. tWP is measured from the beginning of write to the end of write. 3. tCW is measured from the later of CS going low to end of write. 4. tAS is measured from the address valid to the beginning of write. 5. tWR is measured from the end of write to the address change. tWR applied in case a write ends as CS or WE going high. 6. If OE, CS and WE are in the Read Mode during this period, the I/O pins are in the output low-Z state. Inputs of opposite phase of the output must not be applied because bus contention can occur. 7. For common I/O applications, minimization or elimination of bus contention conditions is necessary during read and write cycle. 8. If CS goes low simultaneously with WE going or after WE going low, the outputs remain high impedance state. 9. Dout is the read data of the new address. 10.When CS is low : I/O pins are in the output state. The input signals in the opposite phase leading to the output should not be applied. FUNCTIONAL DESCRIPTION CS WE OE Mode I/O Pin Supply Current H X X* Not Select High-Z ISB, ISB1 L H H Output Disable High-Z ICC L H L Read DOUT ICC L L X Write DIN ICC * X means Don′t Care. -7- Revision 1.0 March 1999 PRELIMINARY PRELIMINARY KM641003C CMOS SRAM Units:millimeters/Inches PACKAGE DIMENSIONS 32-SOJ-400 Preliminary CCPCCCRCELIMINARY #17 10.16 0.400 #32 11.18 ±0.12 0.440 ±0.005 9.40 ±0.25 0.370 ±0.010 0.20 #1 #16 0.008 0.69 MIN 0.027 21.36 MAX 0.841 20.95 ±0.12 0.825 ±0.005 ( 1.30 ) 0.051 ( 1.30 ) 0.051 ( 0.95 ) 0.0375 +0.10 -0.05 +0.004 0.017 -0.002 0.43 1.27 0.050 +0.10 -0.05 +0.004 -0.002 0.71 0.028 -8- 3.76 MAX 0.148 0.10 MAX 0.004 +0.10 -0.05 +0.004 -0.002 Revision 1.0 March 1999