Ordering number : ENA0912 LA73079CL Monolithic Linear IC Video Driver for DSC Overview The LA73079CL is a low voltage drive (2.7V to 3.6V) video driver developed for portable appliances including digital still cameras and cell phones. It incorporates a minus-voltage generator that allows the LA73079CL to generate its output with the pedestal voltage set to 0V, so that no output coupling capacitor is required. This enables substantial reduction in mounting space without concerned about V-sag. Features • Output coupling capacity not required • Low-voltage drive (VCC = 2.7V to 3.6V) • Νο V-sag • Sextic LPF incorporated (fc = 9MHz) • Current drain of 0µA in the standby mode • Amplifier gain selectable from three options (6, 12, and 16dB) (Pin control (GND/Open/VCC)) • Output drive capable of covering maximum 75Ω output, one channel Specifications Maximum Ratings at Ta = 25°C Parameter Maximum supply voltage Allowable power dissipation Symbol Conditions VCC max Pd max Ta ≤ 80°C, *Mounted on a specified board Ratings Unit 4.0 V 160 mW Operating temperature Topr -20 to +85 °C Storage temperature Tstg -55 to +150 °C *: Mounted on a specified board: 10mm×20mm×0.8mm, Paper phenol Any and all SANYO Semiconductor Co.,Ltd. products described or contained herein are, with regard to "standard application", intended for the use as general electronics equipment (home appliances, AV equipment, communication device, office equipment, industrial equipment etc.). The products mentioned herein shall not be intended for use for any "special application" (medical equipment whose purpose is to sustain life, aerospace instrument, nuclear control device, burning appliances, transportation machine, traffic signal system, safety equipment etc.) that shall require extremely high level of reliability and can directly threaten human lives in case of failure or malfunction of the product or may cause harm to human bodies, nor shall they grant any guarantee thereof. If you should intend to use our products for applications outside the standard applications of our customer who is considering such use and/or outside the scope of our intended standard applications, please consult with us prior to the intended use. If there is no consultation or inquiry before the intended use, our customer shall be solely responsible for the use. Specifications of any and all SANYO Semiconductor Co.,Ltd. products described or contained herein stipulate the performance, characteristics, and functions of the described products in the independent state, and are not guarantees of the performance, characteristics, and functions of the described products as mounted in the customer' s products or equipment. To verify symptoms and states that cannot be evaluated in an independent device, the customer should always evaluate and test devices mounted in the customer' s products or equipment. 90507 TI IM 20060116-S00003 No.A0912-1/6 LA73079CL Recommended Operating Conditions at Ta = 25°C Parameter Symbol Recommended Operating supply voltage VCCSTD Operating supply voltage range Conditions Ratings VCCRANGE Unit 3.1 V 2.7 to 3.6 V Electrical Characteristics at Ta = 25°C, VCC = 3.1V Parameter Symbol Ratings Conditions min typ Unit max Current Drain Block Current dissipation 1 ICC ( VIN = White50% ) Current dissipation 2 ICC2 ( Non-signal mode ) Current dissipation 3 4pin = Low Input = White50% 4pin = Low Input = No signal ICC-STBY 14 22 30 mA 7 11.5 15 mA 0 5 µA 5.7 6.2 6.7 dB 4pin = Open (High) ( Standby mode ) Video Block Voltage gain V6 VG-L VIN = 1Vp-p 100% white 2pin = Low (GND) Voltage gain V12 VG-M VIN = 0.5Vp-p 100% white 2pin = MID (Open) 11.7 12.2 12.7 dB Voltage gain V16 VG-H VIN = 317mVp-p 100% white 2pin = High (VCC) 15.7 16.2 16.7 dB Freq. Characteristics Vf f = 100kHz/5MHz -1.5 -0.5 +0.5 dB Differential Gain DG VOUT = 2Vp-p (Modulated Ramp) -2.0 0 -2.0 % Differential Phase DP VOUT = 2Vp-p (Modulated Ramp) -2.0 0 -2.0 deg -5.0 0 +5.0 µA -5.0 0 +5.0 µA VCC-0.5 3.6 V GND 0.3 V VCC-0.3 VCC V 1.4 V 0.3 V Output leak current at standby 1 IOUTH Current when 3V is applied to pin 9, with pin 4 at H (Standby Mode) and pin 9 (VOUT) Output leak current at standby 2 IOUTL Current when 0.1V is applied to pin 9, with pin 4 at H (Standby Mode) and pin 9 (VOUT) Control Terminal Block Stand-by control pin H voltage VTH-STBY-H Stand-by control pin L voltage VTH-STBY-L (SET = ACTIVE MODE) Gain selection control pin H voltage VTH-G-H (SET = 6dB) Pin 2 pin voltage range at which Amp Gain becomes 16dB. VTH-G-M (SET = 12dB) Gain selection control pin L voltage Pin 4 pin voltage range at which the operation mode is effective. (SET = 16dB) Gain selection control pin M voltage Pin 4 pin voltage range at which ICC ≤ 5µA (SET = STANDBY MODE) Pin 2 pin voltage range at which Amp Gain becomes 12dB. VTH-G-L Pin 2 pin voltage range at which Amp Gain becomes 6dB. 1.0 GND 1.2 (OPEN) No.A0912-2/6 LA73079CL Package Dimensions unit : mm (typ) 3334 SIDE VIEW TOP VIEW BOTTOM VIEW 2.3 0.05 2.8 2 2 0.6 1 1 0.3 (0.2) 0.325 0.075 (0.015) 0.8 (0.8) SIDE VIEW SANYO : ECSP2823-10 Pin Assignment, Pin Function Diagram and Block Diagram (Note 1) Position the decoupling capacitor of VCC-GND as near as possible to this IC. VCC AGND High 16dB 2 Open 12dB Low 6dB AMP 75Ω Video Driver GAINCTL 10 4.7µF Active Input signal) Signal → ON No signal → OFF Standby → OFF 1 VCC VOUT TDK C1608 JB OJ 475K ← 0V 9 VOUT 75Ω LPF from DAC 1µF VIN TDK C1608 JB 1C 105K High Open Low 8 3 VCCN CLAMP 7 4 Standby PSAVCTL Active 5 GND (Note 2) Use the input capacity value within a range of 0.1µF to 1µF while checking the sag condition of the output waveform. 2.2µF TDK C1608 JB 1C 225K Minus Voltage Generator ND1 6 2.2µF TDK C1608 JB 1C 225K CLKOUT (Note 3) For these two capacities; Temperature characteristic B rank ( ±10%) Electrostatic tolerance K rank (±10%) and Withstand voltage of 6.3V or more are recommended. (Note 4) Wiring from V OUT (pin 9) to 75Ω must be as short as possible. (Note 5) As the minus power supply in this IC generates the clock for charge pump power supply by extracting the sink component of the input Video signal (synchronous isolation) and by detecting its fall, the portion around the V-syncrhonization of this IC output may be reduced when the pseudo V signal without cut-in pulse is inserted as in the case of certain analog VCR special play (search). On the contrary, there is no problem when the pseudo V signal has the cut-in pulse. Pay due attention on this fact duri ng use. No.A0912-3/6 LA73079CL Pin Functions Symbol Voltage 1 AGND 0V 2 GAINCTL 1.2V Description Equivalent Circuit Analog GND Gain select pin Control of Pin2 GAIN H(VCC) ⇒ 16dB M(OPEN) ⇒ 12dB L(GND) ⇒ 6dB 10 VCC 2.16V REF 1.2V 2 5 3 VIN 1.1V 100kΩ Pin No BUF 0.72V 2kΩ GND Video input terminal (Sync-chip clamp 10 (input High-impedance)) VCC 2kΩ GAIN SET: 6dB⇒1.0Vp-p GAIN SET: 12dB⇒500mVp-p GAIN SET: 16dB⇒317mVp-p 2kΩ 200Ω 200Ω 3 5 VIN 2kΩ Active: ON Standby: OFF 26kΩ GND 1.05V 4 PSAVCTL VCC or 0V Power save mode select pin Control of Pin4 MODE H(VCC) OPEN or VCC±0.5V ⇒ STANDBY L(GND) 0V to 0.3V ⇒ ACTIVE 10 VCC 50kΩ 50kΩ 50kΩ PSAVCTL 4 5 5 GND 4kΩ GND 0V Continued on next page. No.A0912-4/6 LA73079CL Continued from preceding page. Pin No Symbol Voltage 6 CLKOUT +3.0V Description Equivalent Circuit Pin6 : Clock output terminal ↑↓ 10 V CC =3.1V 0V VCC 3V 2V 6 CLKOUT 6pin 1V 50kΩ 50kΩ 0V -1V 50kΩ 7pin 8pin -2V 7 ND1 GND 5 -3V 2.4V +0.5V ↑↓ -2.6V Pin7 : The terminal which transmits 10 an electric charge (-VCC) 5 VCC GND 100kΩ 8 VCCN 0V ↑↓ Pin8 : Negative VCC VCCN 8 -2.5V (-VCC) 50kΩ ND1 7 9 VOUT 0V Video output terminal (Push-pull output Low-impedance) 10 VCC 2Vp-p 0V --0.6V VOUT 9 8 VCC 500Ω + - GND 5 100kΩ 10 50kΩ Active: Low-impedance Standby: High-impedance 1.4V 50kΩ -VCC 2.7V to 3.6V No.A0912-5/6 LA73079CL Test Circuit Diagram VM VM 4.7µF IM PSAVCTL GAINCTL 4 2 10 VCC VOUT VIN 3 VCC VM CLAMP LPF AMP Video Driver 9 1µF AGND 75Ω ACTIVE (Input signal) Yes → ON No → OFF STANDBY→ OFF 1 SG Minus Voltage Generator 5 75Ω M 75Ω GND CLKOUT 6 7 ND1 8 VCCN 2.2µF 2.2µF SANYO Semiconductor Co.,Ltd. assumes no responsibility for equipment failures that result from using products at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges, or other parameters) listed in products specifications of any and all SANYO Semiconductor Co.,Ltd. products described or contained herein. SANYO Semiconductor Co.,Ltd. strives to supply high-quality high-reliability products, however, any and all semiconductor products fail or malfunction with some probability. It is possible that these probabilistic failures or malfunction could give rise to accidents or events that could endanger human lives, trouble that could give rise to smoke or fire, or accidents that could cause damage to other property. When designing equipment, adopt safety measures so that these kinds of accidents or events cannot occur. Such measures include but are not limited to protective circuits and error prevention circuits for safe design, redundant design, and structural design. In the event that any or all SANYO Semiconductor Co.,Ltd. products described or contained herein are controlled under any of applicable local export control laws and regulations, such products may require the export license from the authorities concerned in accordance with the above law. No part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying and recording, or any information storage or retrieval system, or otherwise, without the prior written consent of SANYO Semiconductor Co.,Ltd. Any and all information described or contained herein are subject to change without notice due to product/technology improvement, etc. When designing equipment, refer to the "Delivery Specification" for the SANYO Semiconductor Co.,Ltd. product that you intend to use. Information (including circuit diagrams and circuit parameters) herein is for example only; it is not guaranteed for volume production. Upon using the technical information or products described herein, neither warranty nor license shall be granted with regard to intellectual property rights or any other rights of SANYO Semiconductor Co.,Ltd. or any third party. SANYO Semiconductor Co.,Ltd. shall not be liable for any claim or suits with regard to a third party's intellctual property rights which has resulted from the use of the technical information and products mentioned above. This catalog provides information as of September, 2007. Specifications and information herein are subject to change without notice. PS No.A0912-6/6