SC194B Selectable 3.6V/3.3V/3.0V/2.5V 1A Synchronous Buck Converter POWER MANAGEMENT Description Features The SC194B is a synchronous step-down converter with integrated power devices. Four selectable output voltages suitable for portable device interface, memory function blocks, and 5V to 3.3V voltage conversion are available. Automatic selection of Power Save Mode (PSAVE) is supported which enhances efficiency. A 100% duty cycle mode allows operation for input voltages close to the required output voltage. The need for external components is minimized by providing internal feedback compensation, and allowing selection of the required output voltage by hard wiring VID code inputs. The maximum current rating of the internal MOSFET switches allows a DC output current of 1A. The switching frequency is nominally set to 1MHz, allowing the use of small inductors and capacitors. A flexible clocking scheme is used that allows synchronization to an external oscillator or control by the internal oscillator. Up to 95% efficiency PSAVE operation to maximize efficiency Output current — 1A Input range — 2.7V to 5.5V Four selectable output voltages Quiescent current — 17μA in PSAVE Dynamic voltage positioning capability Fixed 1MHz frequency or 750kHz to 1.25MHz synchronized operation Current mode operation for excellent line and load transient response 100% duty cycle in dropout Soft-start Over-temperature and short-circuit protection Lead-free package — 3mm x 3mm MLPD Applications The device can operate in either forced PWM mode or in PSAVE mode. If PSAVE mode is enabled the part will automatically enter PSAVE at light loads to maintain maximum efficiency across the full load range. For noise sensitive applications, PSAVE mode can be disabled by synchronizing to an external oscillator, or pulling the SYNC/ PWM pin high. Shutdown turns off all the control circuitry to achieve a typical shutdown current of 0.1μA. PDA Pocket PC and Smart Phones USB Powered Modems CPUs and DSPs PC Cards and Notebooks xDSL Applications Standard 5-V to 3.3-V Conversion Typical Application Circuit L1 SC194B VIN 3.6V to 5.5V CIN 10μF August 24, 2006 VIN EN SYNC/PWM VID0 VID1 MODE VOUT 3.3V 1A LX 4.7μH VOUT PGND GND 1 COUT 22μF www.semtech.com SC194B POWER MANAGEMENT Absolute Maximum Ratings Exceeding the specifications below may result in permanent damage to the device or device malfunction. Operation outside of the parameters specified in the Electrical Characteristics section is not recommended. Parameter Symbol Maximum Units Input Supply Voltage VIN -0.3 to 7 V Logic Inputs (SYNC/PWM, EN, MODE, VID0, VID1) VN -0.3 to VIN +0.3, 7V Max V Output Voltage VOUT -0.3 to VIN +0.3, 7V Max V LX Voltage VLX -1 to VIN +1, 7V Max V Thermal Impedance Junction to Ambient(1) θJA 40 °C/W VOUT Short-Circuit to GND tSC Continuous s Operating Ambient Temperature Range TA -40 to +85 °C Storage Temperature TS -60 to +160 °C Junction Temperature TJC -40 to +150 °C Peak IR Reflow Temperature TP 260 °C VESD 2 kV ESD Protection Level (2) Note: (1) Calculated from package in still air, mounted to 3” x 4.5”, 4 layer FR4 PCB with thermal vias under the exposed pad per JESD51 standards. (2) Tested according to JEDEC standard JESD22-A114-B. Electrical Characteristics Unless otherwise noted: VIN = 5V ,VOUT = 3.3V, EN = VIN, SYNC/PWM = VIN, MODE = VIN , TA = -40 to 85°C. Typical values are at TA =25°C. Parameter Conditions Min VIN VIN > VOUT + dropout 2.7 VOUT IOUT = 0.5A, TA = 25°C VOUT = 2.5/3.0/3.3/3.6V VOUT(T) IOUT = 0.5A, TA=-40°C to 85°C VOUT LINE Load Regulation (PWM) VOUT LOAD PSAVE Regulation VOUT PSAVE Input Voltage Range VOUT Accuracy VOUT Temperature Accuracy Line Regulation Symbol Typ Max Units 5.5 V ±1 % ±0.3 ±0.7 % VIN = 2.7V to 5.5V, VOUT = 2.5V, IOUT = 0.5A, TA=-40°C to 85°C ±0.4 ±0.65 % IOUT = 0A to 1A ±0.3 ±0.65 % SYNC/PWM = GND, COUT=22μF +1.3 -0.3 +1.6 -0.6 % P-Channel On Resistance RDSP ILX = 100mA, VIN=3.6V 0.275 Ω N-Channel On Resistance RDSN ILX = 100mA, VIN=3.6V 0.165 Ω Start-Up Time TSTART P-Channel Current Limit ILIM(P) © 2006 Semtech Corp. VIN = 2.7V to 5.5V 2 1.33 1.9 5 ms 2.47 A www.semtech.com SC194B POWER MANAGEMENT Electrical Characteristics (Cont.) Parameter Symbol Conditions Quiescent Current IQ Shutdown Current Typ Max Units SYNC/PWM = GND, IOUT = 0A, VOUT = 1.04 x VOUT(Programmed), VIN= 3.6V 17 28 μA ISD EN = GND, LX = OPEN, VIN= 3.6V 0.1 1 μA LX Leakage Current PMOS ILXP VIN = 3.6V, LX = GND, EN = GND 0.1 2 μA LX Leakage Current NMOS ILXN VIN = 3.6V, LX = 3.6V, EN = GND -2 0.1 Oscillator Frequency fOSC VIN= 3.6V 0.85 1.0 SYNC Frequency (upper) fSYNCU VIN= 3.6V 1.25 SYNC Frequency (lower) fSYNCL VIN= 3.6V UVLO Threshold (upper) VUVL UVLO Hysteresis Thermal Shutdown Thermal Shutdown Hysteresis Min 2.38 1.15 MHz MHz 2.52 750 kHz 2.65 V VUVLHYS 100 mV TSD 145 °C TSD-HYS 10 °C Logic Input High VIH EN, SYNC/PWM, VID0, VID1, MODE Logic Input Low VIL EN, SYNC/PWM, VID0, VID1, MODE Logic Input Current High IIH EN, SYNC/PWM, VID0, VID1, MODE -2 Logic Input Current Low IIL EN, SYNC/PWM, VID0, VID1, MODE -2 © 2006 Semtech Corp. μA 3 1.6 V 0.6 V 0.1 2 μA 0.1 2 μA www.semtech.com SC194B POWER MANAGEMENT Pin Configuration Ordering Information DEVICE PACKAGE SC194BMLTRT(1)(2) MLP 3x3-10 SC194BEVB Evaluation Board Ordering Information VIN 1 MODE 2 SYNC/PWM 3 EN 4 TOP VIEW 10 LX 9 PGND 8 GND 7 VID1 6 VID0 Notes: 1) Lead-free packaging only. This product is fully WEEE and RoHS compliant. 2) Available in tape and reel only. A reel contains 3000 devices. Programmable Output Voltage T VOUT 5 MLP10: 3X3 10 LEAD VID1 VID0 SC194B VOUT 0 0 2.5V 0 1 3.0V 1 0 3.3V 1 1 3.6V Marking Information 194B yyww xxxx yy = two digit year of manufacture ww = two digit week of manufacture xxxx = lot number © 2006 Semtech Corp. 4 www.semtech.com SC194B POWER MANAGEMENT Pin Descriptions Pin # Pin Name 1 VIN 2 MODE 3 SYNC/PWM Oscillator synchronization input — Tie to VIN for forced PWM mode or GND to allow the part to enter PSAVE mode at light loads. Apply an external clock signal for frequency synchronization. 4 EN Enable digital input — A high input enables the SC194B, a low disables and reduces quiescent current to less than 1μA. In shutdown, LX becomes high impedance. 5 VOUT Regulated output voltage and feedback for SC194B 6 VID0 Logic level bit 0 is used in conjunction with VID1 to set the output voltage. Connect high or low as required to select the desired output voltage. If not connected, the output voltage will be indeterminate. 7 VID1 Logic level bit 1 is used in conjunction with VID0 to set the output voltage. Connect high or low as required to select the desired output voltage. If not connected, the output voltage will be indeterminate. 8 GND Ground 9 PGND 10 LX T THERMAL PAD © 2006 Semtech Corp. Pin Function Input power supply voltage MODE select pin where MODE = VIN to select 100% duty cycle function and MODE = GND to disable Power Ground Inductor connection to the switching FETs Pad is for heatsinking purposes — not connected internally. Connect exposed pad to ground plane using multiple vias. 5 www.semtech.com SC194B POWER MANAGEMENT Block Diagram Plimit Amp 1 VIN 10 LX 9 PGND 8 GND Current Amp EN SYNC/ PWM 4 OSC & Slope Generator 3 Control Logic PWM Comp 500mV Ref Error Amp MODE 2 VID1 7 VID0 6 VOUT 5 © 2006 Semtech Corp. PSAVE Comp Voltage Select 6 Nlimit Amp www.semtech.com SC194B POWER MANAGEMENT Applications Information SC194B Detailed Description The SC194B is a synchronous step-down Pulse Width Modulated (PWM), DC-DC converter utilizing a 1MHz fixed-frequency current mode architecture. The device is designed to operate in fixed-frequency PWM mode across the full load range and can enter power save mode (PSAVE) utilizing Pulse Frequency Modulation (PFM) at light loads to maximize efficiency. • Over-voltage protection • Soft-start Thermal Shutdown The device has a thermal shutdown feature to protect the SC194B if the junction temperature exceeds 145°C. In thermal shutdown the on-chip power devices are disabled, tri-stating the LX output. Switching will resume when the temperature drops by 10°C. During this time if the output voltage decreases by more than 60% of its programmed value, a soft-start will be invoked. Operation During normal operation the PMOS MOSFET is activated on each rising edge of the internal oscillator. Current feedback for the switching regulator is through the PMOS current path, and it is amplified and summed with the internal slope compensation network. The voltage feedback loop uses an internal feedback divider. The ontime is determined by comparing the summed current feedback and the output of the error amplifier. The period is set by the onboard oscillator or by an external clock attached to the SYNC/PWM pin. Current Limit The PMOS and NMOS power devices of the buck switcher stage are protected by current limit functions. In the case of a short to ground on the output, the part enters frequency foldback mode that causes the switching frequency to divide by a factor determined by the output voltage. This prevents the inductor current from "stair-casing". Over-Voltage Protection Over-voltage protection is provided on the SC194B. In the event of an over-voltage on the output in switcher mode, the PWM drive is disabled, tri-stating the LX output. The part will not resume switching until the output voltage has fallen below 2% of the regulation voltage. The SC194B has an internal synchronous NMOS rectifier and does not require a Schottky diode on the LX pin. Programmable Output Voltage The SC194B has four pre-determined output voltage values which can be individually selected by the correct programming of the VID0 and VID1 pins (see Programmable Output Voltage table on Page 4). This eliminates the need for external programming resistors saving PCB area and inventory. The VID pins can be statically tied to GND or VIN for fixed output configurations or they may be driven by a microprocessor enabling the possibility of dynamic voltage adjustment for host equipment "sleep" states. Soft-Start The soft-start mode is enabled after every shutdown cycle to limit in-rush current. In conjunction with the frequency foldback, this controls the maximum current during startup. The PMOS current limit is stepped up through seven soft-start levels to the full value by a timer driven from the internal oscillator. During soft-start, the switching frequency is stepped by 1/8, 1/4, and 1/2 of the internal oscillator frequency up to the full value, under control of three output voltage thresholds. As soon as the output voltage is within 2% of the regulation voltage, soft-start mode is disabled. Oscillator Synchronization Opotions The SC194B is designed to operate in continuous conduction, fixed-frequency mode. When the SYNC/PWM pin is tied high the part runs in PWM mode using the internal oscillator. The part can be synchronized to an external clock by driving a clock signal into the SYNC/ PWM pin. The part synchronizes to the rising edge of the clock. Power Save Mode Operation The PSAVE mode may be selected by tying the SYNC/PWM pin to GND. Selecting PSAVE mode will enable the SC194B to automatically activate/deactivate operation at light loads maximizing efficiency across the full load range. The SC194B automatically detects the load current at which it should enter PSAVE mode. The SC194B is optimized to track maximum efficiency with respect to VIN. Protection Features The SC194B provides the following protection features: • Thermal shutdown • Current limit © 2006 Semtech Corp. 7 www.semtech.com SC194B POWER MANAGEMENT Applications Information (Cont.) In PSAVE mode VOUT is driven from a lower level to an upper level by a switching burst. Once the upper level has been reached the switching is stopped and the quiescent current is reduced. VOUT falls from the upper to lower levels in this low current state as the load current discharges the output capacitor. The burst-to-off period in PSAVE will decrease as the load current reduces. 100% Duty Cycle Operation The 100% duty cycle mode may be selected by connecting the MODE pin high. This will allow the SC194B to maintain output regulation under low input voltage/high output voltage conditions. In 100% duty cycle operation, as the input supply drops toward the output voltage, the PMOS on-time increases linearly above the maximum value in fixed-frequency operation until the PMOS is active continuously. Once the PMOS is switched on continuously, the output voltage tracks the input voltage minus the voltage drop across the PMOS power device and inductor according to the following relationship: The PSAVE switching burst frequency is controlled so that the inductor current ripple is similar to that in PWM mode. The SC194B automatically detects when to exit PSAVE mode by monitoring VOUT. For the SC194B to exit PSAVE mode, the load must be increased, causing VOUT to decrease until the power save exit threshold is reached. PSAVE levels are set high to minimize the undershoot when exiting PSAVE. The lower PSAVE comparator level is set +0.7% above VOUT, and the upper comparator level at +1.5% above VOUT, with the exit threshold at -2% below VOUT. VOUT where, VOUT VIN IOUT RDSP RIND If PSAVE operation is required then a 22μF output capacitor must be used. OFF = Output voltage = Input voltage = Output current = PMOS switch ON resistance = Series resistance of the inductor Inductor Selection The SC194B is designed for use with a 4.7μH inductor. The magnitude of the inductor current ripple is dependent on the inductor value and can be determined by the following equation: Power Save Operation BURST VIN IOUT u (RDSP RIND ) Higher Load Applied 1.5% 0.7% PSAVE Mode at Light Load PWM Mode at Medium/ High Load VOUT 'IL -2% VOUT L u fosc This equation demonstrates the relationship between input voltage, output voltage, and inductor ripple current. Inductor Current The inductor should have a low DCR to minimize the conduction losses and maximize efficiency. As a minimum requirement, the DC current rating of the inductor should be equal to the maximum load current plus half of the inductor current ripple as shown by the following equation: 0A Time IL(PK) © 2006 Semtech Corp. § VOUT · ¸ ¨¨1 VIN ¸¹ © 8 IOUT(MAX) 'IL 2 www.semtech.com SC194B POWER MANAGEMENT Applications Information (Cont.) Final inductor selection will depend on various design considerations such as efficiency, EMI, size and cost. Table 1 lists the manufacturers of practical inductor options. Capacitors with X7R or X5R ceramic dielectric are strongly recommended for their low ESR and superior temperature and voltage characteristics. Y5V capacitors should not be used as their temperature coefficients make them unsuitable for this application. Table 2 lists the manufacturers of recommended capacitor options. Table 1 — Recommended Inductors Value (μH) DCR (Ω) Saturation Current (A) Tolerance (+%) Dimensions LxWxH (mm) BI Technologies HM66304R7 4.7 0.072 1.32 20 4.7 × 4.7 ×3.0 Manufacturer/Part No. Coilcraft D01608C-472ML 4.7 0.09 1.5 20 6.6 × 4.5 ×3.0 TDK VLCF4018T- 4R7N1R0-2 4.7 0.101 1.07 30 4.3 × 4.0 ×1.8 Manufacturer/Part No. Table 2 — Recommended Capacitors CIN Selection The source input current to a buck converter is noncontinuous. To prevent large input voltage ripple a low ESR ceramic capacitor is required. A minimum value of 10μF should be used for sufficient input voltage filtering and a 22μF should be used for improved input voltage filtering. Value (μF) Rated Voltage (VDC) Temperature Characteristic Case Size Murata GRM21BR60J226ME39L 22 6.3 X5R 0805 Murata GRM188R60J106MKE19 10 6.3 X5R 0603 TDK C2012X5R0J106K 10 6.3 X5R 0603 Note: Where PSAVE operation is required 22μF must be used for COUT. COUT Selection The internal compensation is designed to work with a certain output filter corner frequency defined by the equation: fC 1 2S L u COUT This single pole filter is designed to operate with a minimum output capacitor value of 10μF. Larger output capacitor values will improve transient performance. If PSAVE operation is required the minimum capacitor value is 22μF. Output voltage ripple is a combination of the voltage ripple from the inductor current charging and discharging the output capacitor and the voltage created from the inductor current ripple through the output capacitor ESR. Selecting an output capacitor with a low ESR will reduce the output voltage ripple component, as can be seen in the following equation: ǻVOUT(ESR) © 2006 Semtech Corp. ǻIL(ripple) u ESR COUT 9 www.semtech.com SC194B POWER MANAGEMENT Applications Information (Cont.) PCB Layout Considerations Poor layout can degrade the performance of the DC-DC converter and can contribute to EMI problems, ground bounce and resistive voltage losses. Poor regulation and instability can result. A few simple design rules can be implemented to ensure good layout: 1. Place the inductor and filter capacitors as close to the device as possible and use short wide traces between the power components. 2. Route the output voltage feedback path away from the inductor and LX node to minimize noise and magnetic interference. 3. Maximize ground metal on the component side to improve the return connection and thermal dissipation. Separation between the LX node and GND should be maintained to avoid coupling of switching noise to the ground plane. 4. Use a ground plane with several vias connecting to the component side ground to further reduce noise interference on sensitive circuit nodes. GND VIN CIN LX LOUT SC194B COUT VOUT GND © 2006 Semtech Corp. 10 www.semtech.com SC194B POWER MANAGEMENT Typical Characteristics Efficiency vs. Load Current VOUT = 3.6V 100 Efficiency vs. Load Current VOUT = 3.3V 100 VIN=3.9V, PSAVE 90 VIN=4.2V, PSAVE VIN=5.0V, PSAVE 70 Efficiency (%) 80 60 VIN=3.9V, PWM 50 VIN=5.0V, PWM 40 VIN=4.2V, PSAVE VIN=5.0V, PSAVE 70 Efficiency (%) 80 VIN=3.9V, PSAVE 90 60 50 VIN=3.9V, PWM VIN=5.0V, PWM 40 30 30 VIN=4.2V, PWM 20 VIN=4.2V, PWM 20 10 10 0 0.0001 0.001 0.01 0.1 0 0.0001 10 1 0.001 0.01 IOUT (A) Efficiency vs. Load Current VOUT = 3.0V 100 100 VIN=3.6V, PSAVE 10 VIN=3.3V, PSAVE 90 80 VIN=4.2V, PSAVE 70 60 VIN=5.0V, PWM 50 40 VIN=3.6V, PWM 30 VIN=5.0V, PSAVE 60 50 40 VIN=5.0V, PWM VIN=4.2V, PWM 20 10 10 0.001 VIN=3.3V, PWM 30 VIN=4.2V, PWM 20 0 0.0001 VIN=4.2V, PSAVE 70 VIN=5.0V, PSAVE Efficiency (%) Efficiency (%) 1 Efficiency vs. Load Current VOUT = 2.5V 90 80 0.1 IOUT (A) 0.1 0.01 1 0 0.0001 10 0.001 0.01 0.1 1 10 IOUT (A) IOUT (A) Efficiency vs. Input Voltage VOUT = 3.3V PWM to PSAVE Hysteresis 100 95 VOUT=3.3V,PSAVE VOUT=3.3V,PWM 95 94 PSAVE Entry IOUT Decreasing Efficiency (%) 90 Eff (%) VOUT=2.5V,PWM VOUT=2.5V,PSAVE 85 80 92 PSAVE EXIT IOUT Increasing PWM Mode 91 75 70 2.5 93 3 3.5 4 4.5 5 5.5 90 0.1 6 Vin (V) 0.15 0.2 0.25 0.3 IOUT (A) 0.35 0.4 0.45 0.5 IOUT=500 mA(PWM)/50 mA(PSAVE) © 2006 Semtech Corp. 11 www.semtech.com SC194B POWER MANAGEMENT Typical Characteristics VOUT vs. VIN Load Regulation 3.6 Vin=5V, Vout=3.3V,PWM 3.292 3.4 VOUT=3.3V,PSAVE 3.2 VOUT=3.3V,PWM 3.29 3.288 VOUT (V) VOUT (V) 3 2.8 2.6 VOUT=2.5V,PSAVE 2.4 VOUT=2.5V,PWM 3.286 3.284 3.282 3.28 2.2 2 2.5 3 3.5 4 4.5 5 5.5 3.278 0 6 0.2 0.4 0.6 0.8 IOUT (A) VIN (V) 1 1.4 1.2 1.6 IOUT=500 mA(PWM)/50 mA(PSAVE) Quiescent Current vs. Input Voltage VOUT vs. Temperature 3.35 VOUT = 3.3V 22 21 3.34 TA=85°C Quiescent Current (uA) 20 3.33 VIN=5.0V,PSAVE 3.32 VOUT (V) PSAVE Mode 3.31 3.3 3.29 VIN=5.0V,PWM 19 18 17 TA=25°C 16 15 14 3.28 TA=-40°C 13 3.27 -50 -40 -30 -20 -10 0 10 20 30 40 50 60 70 80 12 2.5 90 3 4 3.5 VIN(V) TA (°C) Quiescent Current vs. Input Voltage 6 4.5 5 5.5 6 N-Channel RDSON vs. Input Voltage PWM Mode 0.22 TA=-40°C 5.5 0.20 TA=85°C 0.18 5 TA=25°C RDSON (Ω) Quiescent Current (mA) TA=85°C 4.5 TA=25°C 0.16 TA=-40°C 4 0.14 3.5 0.12 3 2.5 3 3.5 4 4.5 5 5.5 0.10 2.7 6 VIN (V) © 2006 Semtech Corp. 12 3.2 3.7 4.2 VIN (V) 4.7 5.2 www.semtech.com SC194B POWER MANAGEMENT Typical Characteristics (Cont.) Switching Frequency vs. Temperature P-Channel RDSON vs. Input Voltage 1050 0.40 1040 Switching Frequency (kHz) 0.35 RDSON (Ω) 0.30 TA=85°C 0.25 TA=25°C 0.20 TA=-40°C 1030 VIN=5.5V 1020 1010 VIN=2.7V 1000 990 VIN=3.6V 980 970 0.15 960 0.10 2.7 3.2 3.7 4.2 VIN(V) 4.7 950 -50 5.2 -30 -10 10 30 50 70 90 110 130 TJ (°C) PSAVE Operation 100% Duty Cycle Mode VOUT (50mV/div) VOUT (50mV/div) ILX (200mA/div) ILX (500mA/div) VLX (5V/div) VLX (2V/div) Time (2μs/div) Condition VIN=5V, lOUT=50mA, VOUT=3.3V Time (400ns/div) Condition VIN= 3.8V, lOUT= 1A, VOUT= 3.3V PWM Operation PSAVE Start-UP VEN (2V/div) VOUT (20mV/div) VOUT (2V/div) ILX (500mA/div) IIN (200mA/div) VLX (5V/div) Time (400μs/div) Condition VIN=5V, lOUT=10mA, VOUT=3.3V Time (1μs/div) Condition VIN=5V, lOUT=50mA, VOUT=3.3V © 2006 Semtech Corp. 13 www.semtech.com SC194B POWER MANAGEMENT Typical Characteristics (Cont.) PWM Start-Up Load Transient Response PWM VEN (2V/div) VOUT (200mV/div) VOUT (2V/div) IOUT (500mA/div) IIN (200mA/div) Time (400μs/div) Condition VIN= 5V, lOUT = 10mA, VOUT= 3.3V Time (400μs/div) Condition VIN= 5V, lOUT = 1A to 100mA, VOUT = 3.3V Load Transient Response PSAVE VID Code Change PWM VOUT (200mV/div) VOUT (200mV/div) IOUT (500VmA/div)) VVID1 (2V/div) Time (400μs/div) Condition VIN= 5V, lOUT = 1A, VOUT = 2.5 to 3.3V Time (400μs/div) Condition VIN= 5V, lOUT = 1A to 100mA, VOUT = 3.3V © 2006 Semtech Corp. 14 www.semtech.com SC194B POWER MANAGEMENT Applications Circuits VOUT = 3.6V Forced PWM and 100% Duty Cycle L1 SC194B VIN 3.9 to 5.5V CIN 10μF VIN EN SYNC/PWM VID0 VID1 MODE VOUT 3.6V 1A LX 4.7μH VOUT COUT PGND GND 10μF Dynamic Voltage Positioning for Reduced System Dissipation in "Sleep" Modes VIN 2.7V to 5.5V CIN 10μF L1 SC194B From uP Sleep controller VIN EN SYNC/PWM VID0 VID1 MODE VOUT 3.3V norm VOUT 2.5V “sleep” LX 4.7μH VOUT COUT PGND GND 22μF VOUT = 2.5V with PSAVE and 100% Duty Cycle VIN 2.7V to 5.5V CIN 10μF © 2006 Semtech Corp. SC194B VIN LX EN SYNC/PWM VOUT VID0 VID1 PGND MODE GND 15 L1 VOUT 2.5V 1A 4.7μH COUT 22μF www.semtech.com SC194B POWER MANAGEMENT Outline Drawing - MLP-10 A E DIMENSIONS INCHES MILLIMETERS DIM MIN NOM MAX MIN NOM MAX B A A1 A2 b C D E e L N aaa bbb E PIN 1 INDICATOR (LASER MARK) A aaa C A1 C 1 .039 .002 (.008) .009 .011 .079 .083 .048 .052 .118 .122 .020 BSC .012 .016 .020 10 .003 .004 .031 .000 .007 .074 .042 .114 0.80 1.00 0.00 0.05 (0.20) 0.18 0.23 0.30 1.87 2.02 2.12 1.06 1.21 1.31 2.90 3.00 3.10 0.50 BSC 0.30 0.40 0.50 10 0.08 0.10 SEATING PLANE C A2 2 LxN D N e bxN bbb C A B NOTES: 1. CONTROLLING DIMENSIONS ARE IN MILLIMETERS (ANGLES IN DEGREES). 2. COPLANARITY APPLIES TO THE EXPOSED PAD AS WELL AS TERMINALS. © 2006 Semtech Corp. 16 www.semtech.com SC194B POWER MANAGEMENT Land Pattern - MLP-10 DIMENSIONS K (C) H G Y X Z DIM INCHES MILLIMETERS C G H K P X Y Z (.112) .075 .055 .087 .020 .012 .037 .150 (2.85) 1.90 1.40 2.20 0.50 0.30 0.95 3.80 P NOTES: 1. THIS LAND PATTERN IS FOR REFERENCE PURPOSES ONLY. CONSULT YOUR MANUFACTURING GROUP TO ENSURE YOUR COMPANY'S MANUFACTURING GUIDELINES ARE MET. Contact Information Semtech Corporation Power Management Products Division 200 Flynn Road, Camarillo, CA 93012 Phone: (805) 498-2111 Fax: (805) 498-3804 www.semtech.com © 2006 Semtech Corp. 17 www.semtech.com