M54HC4060 RAD-HARD 14 STAGE BINARY COUNTER/OSCILLATOR ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ HIGH SPEED: fMAX = 65MHz (TYP.) at VCC = 6V LOW POWER DISSIPATION: ICC =4µA(MAX.) at TA=25°C HIGH NOISE IMMUNITY: VNIH = VNIL = 28% VCC (MIN.) SYMMETRICAL OUTPUT IMPEDANCE: |IOH| = IOL = 4mA (MIN) BALANCED PROPAGATION DELAYS: tPLH ≅ tPHL WIDE OPERATING VOLTAGE RANGE: VCC (OPR) = 2V to 6V PIN AND FUNCTION COMPATIBLE WITH 54 SERIES 4060 SPACE GRADE-1: ESA SCC QUALIFIED 50 krad QUALIFIED, 100 krad AVAILABLE ON REQUEST NO SEL UNDER HIGH LET HEAVY IONS IRRADIATION DEVICE FULLY COMPLIANT WITH SCC-9204-076 DESCRIPTION The M54HC4060 is an high speed CMOS 14-STAGE BINARY COUNTER/OSCILLATOR fabricated with silicon gate C2MOS technology. DILC-16 FPC-16 ORDER CODES PACKAGE FM EM DILC FPC M54HC4060D M54HC4060K M54HC4060D1 M54HC4060K1 The oscillator configuration allows design of either RC or crystal oscillator circuits. A high level on the CLEAR accomplishes the reset function, i.e. all counter outputs are made low and the oscillator is disabled. A negative transition on the clock input increments the counter. Ten kinds of divided output are provided; 4 to 10 and 12 to 14 stage inclusive. The maximum division available at Q12 is 1/16384 f oscillator. The Ø1 input and the CLEAR input are equipped with protection circuits against static discharge and transient excess voltage. PIN CONNECTION May 2004 Rev. 1 1/12 M54HC4060 Figure 1: IEC Logic Symbols Figure 2: Input And Output Equivalent Circuit Table 1: Pin Description PIN N° 1, 2, 3 7, 5, 4, 6, 14, 13, 15 SYMBOL Q4 to Q10 9 ØO 10 ØO 11 ØI 12 8 CLEAR GND VCC 16 NAME AND FUNCTION Q12 to Q14 Counter Outputs Counter Outputs External Capacitor Connection External Resistor Connection Clock Input / Oscillator Pin Master Reset Ground (0V) Positive Supply Voltage Table 2: Truth Table ØI CLEAR FUNCTION X H COUNTER IS RESET TO ZERO STATE ØO OUTPUT GOES TO HIGH LEVEL ØO OUTPUT GOES TO LOW LEVEL L COUNT UP ONE STEP L NO CHANGE X : Don’t Care 2/12 M54HC4060 Figure 3: Logic Diagram This logic diagram has not be used to estimate propagation delays Table 3: Absolute Maximum Ratings Symbol VCC Parameter Supply Voltage Value Unit -0.5 to +7 V -0.5 to VCC + 0.5 -0.5 to VCC + 0.5 V DC Input Diode Current ± 20 mA IOK DC Output Diode Current ± 20 mA IO DC Output Current ± 25 mA ± 50 mA VI DC Input Voltage VO DC Output Voltage IIK ICC or IGND DC VCC or Ground Current PD Power Dissipation Tstg Storage Temperature TL Lead Temperature (10 sec) V 300 mW -65 to +150 °C 265 °C Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional operation under these conditions is not implied Table 4: Recommended Operating Conditions Symbol VCC Parameter Supply Voltage Value Unit 2 to 6 V VI Input Voltage 0 to VCC V VO Output Voltage 0 to VCC V Top Operating Temperature Input Rise and Fall Time tr, tf -55 to 125 °C VCC = 2.0V 0 to 1000 ns VCC = 4.5V 0 to 500 ns VCC = 6.0V 0 to 400 ns 3/12 M54HC4060 Table 5: DC Specifications Test Condition Symbol VIH VIL VOH VOL VOH VOL II ICC 4/12 Parameter High Level Input Voltage Low Level Input Voltage High Level Output Voltage (Q Output) Low Level Output Voltage (Q Output) High Level Output Voltage (ØO, ØO Output) Low Level Output Voltage (ØO, ØO Output) Input Leakage Current Quiescent Supply Current Value TA = 25°C VCC (V) Min. 2.0 4.5 6.0 2.0 4.5 6.0 Typ. Max. 1.5 3.15 4.2 -40 to 85°C -55 to 125°C Min. Min. Max. 1.5 3.15 4.2 0.5 1.35 1.8 Max. 1.5 3.15 4.2 0.5 1.35 1.8 V 0.5 1.35 1.8 2.0 IO=-20 µA 1.9 2.0 1.9 1.9 4.5 IO=-20 µA 4.4 4.5 4.4 4.4 6.0 IO=-20 µA 5.9 6.0 5.9 5.9 4.5 IO=-4.0 mA 4.18 4.31 4.13 4.10 6.0 IO=-5.2 mA 5.68 5.8 5.63 5.60 2.0 IO=20 µA 0.0 0.1 0.1 0.1 4.5 IO=20 µA 0.0 0.1 0.1 0.1 IO=20 µA 0.0 0.1 0.1 0.1 4.5 IO=4.0 mA 0.17 0.26 0.33 0.40 0.18 0.26 6.0 IO=5.2 mA IO=-20 µA 1.8 2.0 1.8 1.8 4.5 IO=-20 µA 4.4 4.5 4.0 4.0 6.0 IO=-20 µA 5.5 5.9 5.5 5.5 0.33 V V 6.0 2.0 Unit V 0.40 V 2.0 IO=-20 µA 0.0 0.2 0.2 0.2 4.5 IO=-20 µA 0.0 0.5 0.5 0.5 6.0 IO=-20 µA 0.1 0.5 0.5 0.5 6.0 VI = VCC or GND ± 0.1 ±1 ±1 µA 6.0 VI = VCC or GND 4 40 80 µA V M54HC4060 Table 6: AC Electrical Characteristics (CL = 50 pF, Input tr = tf = 6ns) Test Condition Symbol Parameter tTLH tTHL Output Transition Time tPLH tPHL Propagation Delay Time (ØI - Q4) tPD tPHL fMAX Propagation Delay Time Difference (Qn - Qn+1) Propagation Delay Time (CLEAR - Qn) Maximum Clock Frequency tW(H) tW(L) Minimum Pulse Width (ØI) tW(H) Minimum Pulse Width (CLEAR) tREM Minimum Removal Time Value TA = 25°C VCC (V) Min. 2.0 4.5 6.0 2.0 4.5 6.0 2.0 4.5 6.0 2.0 4.5 6.0 2.0 4.5 6.0 2.0 4.5 6.0 2.0 4.5 6.0 2.0 4.5 6.0 6 30 35 Typ. Max. 30 8 7 170 41 30 32 7 5 85 23 17 12 50 65 30 8 7 30 8 7 40 10 9 75 15 13 300 60 51 75 15 13 195 39 33 -40 to 85°C -55 to 125°C Min. Min. Max. 95 19 16 375 75 64 95 19 16 245 49 42 5 24 28 75 15 13 75 15 13 100 20 17 Max. 110 22 19 450 90 76 110 22 19 295 59 50 4 20 24 95 19 16 95 19 16 125 25 21 Unit ns ns ns ns MHz 110 22 19 110 22 19 150 30 26 ns ns ns Table 7: Capacitive Characteristics Test Condition Symbol Parameter VCC (V) Value TA = 25°C Min. Typ. Max. 10 CIN Input Capacitance 5.0 5 CPD Power Dissipation Capacitance (note 1) 5.0 27 -40 to 85°C -55 to 125°C Min. Min. Max. 10 Unit Max. 10 pF pF 1) CPD is defined as the value of the IC’s internal equivalent capacitance which is calculated from the operating current consumption without load. (Refer to Test Circuit). Average operating current can be obtained by the following equation. ICC(opr) = CPD x VCC x fIN + ICC 5/12 M54HC4060 Figure 4: Test Circuit CL = 50pF or equivalent (includes jig and probe capacitance) RT = ZOUT of pulse generator (typically 50Ω) Figure 5: Waveform - Propagation Delay Times, Minimum Pulse Width (ØI) (f=1MHz; 50% duty cycle) 6/12 M54HC4060 Figure 6: Waveform - Propagation Delay Times, Minimum Pulse Width (CLEAR) (f=1MHz; 50% duty cycle) Figure 7: Waveform - Propagation Delay Times (f=1MHz; 50% duty cycle) 7/12 M54HC4060 Figure 8: Waveform - Propagation Delay Times (f=1MHz; 50% duty cycle) Figure 9: Typical Clock Drive Circuits 8/12 M54HC4060 DILC-16 MECHANICAL DATA mm. inch DIM. MIN. TYP MAX. MIN. TYP. MAX. A 2.1 2.71 0.083 0.107 a1 3.00 3.70 0.118 0.146 a2 0.63 1.14 0.025 B 1.82 2.39 0.072 b 0.40 0.45 0.50 0.016 0.018 0.020 b1 0.20 0.254 0.30 0.008 0.010 0.012 D 20.06 20.32 20.58 0.790 0.800 0.810 E 7.36 7.62 7.87 0.290 0.300 0.310 e 0.88 2.54 0.035 0.045 0.094 0.100 e1 17.65 17.78 17.90 0.695 0.700 0.705 e2 7.62 7.87 8.12 0.300 0.310 0.320 F 7.29 7.49 7.70 0.287 0.295 0.303 I 3.83 0.151 K 10.90 12.1 0.429 0.476 L 1.14 1.5 0.045 0.059 0056437F 9/12 M54HC4060 FPC-16 MECHANICAL DATA mm. inch DIM. MIN. TYP MAX. MIN. TYP. MAX. A 6.75 6.91 7.06 0.266 0.272 0.278 B 9.76 9.94 10.14 0.384 0.392 0.399 C 1.49 1.95 0.059 D 0.102 0.127 0.152 0.004 0.005 0.006 E 8.76 8.89 9.01 0.345 0.350 0.355 F 0.077 1.27 G 0.38 H 6.0 L 18.75 M 0.33 0.050 0.43 0.48 0.015 0.017 0.019 0.237 0.38 N 22.0 0.738 0.43 0.013 0.867 0.015 4.31 0.017 0.170 G F D H 9 16 A N L 8 1 H E B 10/12 M C 0016030E M54HC4060 Table 8: Revision History Date Revision 14-May-2004 1 Description of Changes First Release 11/12 M54HC4060 Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics. The ST logo is a registered trademark of STMicroelectronics All other names are the property of their respective owners © 2004 STMicroelectronics - All Rights Reserved STMicroelectronics GROUP OF COMPANIES Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States. http://www.st.com 12/12