ST3243 3 to 5.5V, 400Kbps, RS-232 Transceiver with auto-powerdown General features ■ 1µA supply current achieved when in autopowerdown ■ 250kbps minimum guaranteed data rate ■ Guaranteed 6V/µs slew rate range ■ Guaranteed mouse drive ability ■ 0.1µF external capacitors ■ Meet EIA/TIA-232 specifications down to 3V ■ Available in SO-28, SSOP-28 and TSSOP28 SOP SSOP Description The ST3243 device consists of 3 drivers, 5 receivers and a dual charge-pump circuit. The device meets the requirements of EIA/TIA and V.28/V.24 communication standards providing high data rate capability. The receiver R2 is always active to implement a wake-up feature for serial port. The ST3243 has a proprietary low-dropout transmitter output stage enabling true RS-232 performance from a 3.0V to 5.5V supply with a dual charge pump. The device is guaranteed to run at data rates of 250kbps while maintaining RS-232 output levels. The Auto-powerdown feature functions when FORCEON is low and FORCEOFF is high. During this mode of operation, if the device does not TSSOP sense a valid RS-232 signal, the driver outputs are disabled. If FORCEOFF is set low, both drivers and receivers (expert R2B) are shut off, and supply current is reduced to 1mA. Disconnecting the serial port or turning off the peripheral drives causes the auto-powerdown condition to occur. Auto-powerdown can be disabled when FORCEON and FORCEOFF are high, and should be done when driving a serial mouse. With Autopowerdown enabled, the device is activated automatically when a valid signal is applied to any receiver input. Typical application are in notebook, subnotebook, palmtop computers, battery-powered equipment, hand-held equipment, peripherals and printers. Order code Part number Temperature range Package Comments ST3243CDR 0 to 70 °C SO-28 (Tape & Reel) 1000 parts per reel ST3243CPR 0 to 70 °C SSOP-28 (Tape & Reel) 1350 parts per reel ST3243CTR 0 to 70 °C TSSOP28 (Tape & Reel) 2500 parts per reel ST3243BTR -40 to 85 °C TSSOP28 (Tape & Reel) 2500 parts per reel March 2006 Rev 7 1/20 www.st.com 20 Contents ST3243 Contents 1 Pin configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 1.1 Truth tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 2 Maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 3 Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 4 Application circuits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 5 Typical performance characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 6 Package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 7 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 2/20 ST3243 Pin configuration 1 Pin configuration Figure 1. Pin configuration Table 1. Pin description Pin n° Symbol Name and function 1 C2+ Positive terminal of inverting charge pump capacitor 2 C2- Negative terminal of inverting charge pump capacitor 3 V- -5.5V Generated by the charge pump 4 R1IN First receiver input voltage 5 R2IN Second receiver input voltage 6 R3IN Third receiver input voltage 7 R4IN Fourth receiver input voltage 8 R5IN Fifth receiver input voltage 9 T1OUT First transmitter output voltage 10 T2OUT Second transmitter output voltage 11 T3OUT Third transmitter output voltage 12 T3IN Third transmitter input voltage 13 T2IN Second transmitter input voltage 14 T1IN First transmitter input voltage 15 R5OUT Fifth receiver output voltage 16 R4OUT Fourth receiver output voltage 17 R3OUT Third receiver output voltage 3/20 Pin configuration Table 1. ST3243 Pin description Pin n° Symbol 18 R2OUT Second receiver output voltage 19 R1OUT First receiver output voltage 20 R2OUTB Non-inverting complementary receiver output, always active for wake-up 21 INVALID Output of the valid signal detector. Indicates if a valid RS-232 level is present on receiver inputs logic "1" 22 FORCEOFF Drive low to shut down transmitters and on-board power supply. This overrides all automatic circuitry and FORCEON 23 FORCEON Drive high to override automatic circuitry keeping transmitters on (FORCEOFF must be high) 24 C1- 25 GND Ground 26 VCC Supply voltage 27 V+ 5.5V Generated by the charge pump 28 C1+ Positive terminal of voltage-charge pump capacitor 1.1 Name and function Negative terminal of voltage-charge pump capacitor Truth table Table 2. Note: 4/20 FORCE OFF TOUT ROUT R2OUTB 0 HIGH Z HIGH Z ACTIVE Note: 1 ACTIVE Note: ACTIVE Note: ACTIVE Note: If the part is in auto-powerdown mode (FORCE OFF = VCC, FORCE ON = GND) it is shutdown, if no valid RS-232 levels are present on all receiver input ST3243 Maximum ratings 2 Maximum ratings Table 3. Absolute maximum ratings Symbol Parameter Unit -0.3 to 6 V VCC Supply voltage V+ Doubled voltage terminal (VCC -0.3) to 7 V V- Inverted voltage terminal 0.3 to -7 V 13 V -0.3 to 6 V ± 25 V ± 13.2 V -0.3 to (VCC + 0.3) V V+ +|V-| FORCEON, Input voltage FORCEOFF, TIN RIN Receiver input voltage range TOUT Transmitter output voltage range ROUT ROUTB INVALID tSHORT Tstg Note: Value Receiver output voltage range Short circuit duration on TOUT (one at a time) Continuous Storage temperature range -65 to 150 1 Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional operation under these condition is not implied. V+ and V- can have a maximum magnitude of +7V, but their absolute addition can not exceed 13 V. 2 The device doesn’t meet 1KV ESD HBM °C 5/20 Electrical characteristics 3 ST3243 Electrical characteristics Typical values are referred to TA = 25°C Table 4. Electrical characteristics (C1 - C4 = 0.1µF, VCC = 3V to 5.5V, TA = -40 to 85°C, unless otherwise specified. Symbol Parameter Test Conditions IASHDN Supply current auto-powerdown ISHDN ISHDN Table 5. Symbol Typ. Max. Unit VCC = 3.3 or 5.0V, TA = 25°C All R_IN open, FORCEOFF = VCC 1 10 µA Shutdown supply current VCC = 3.3 or 5.0V, TA = 25°C All R_IN open, FORCEOFF = GND 1 10 µA Supply current auto-powerdown disabled VCC = 3.3 or 5.0V TA = 25°C FORCEON = FORCEOFF = VCC No Load 0.3 1 mA Logic input electrical characteristics (C1 - C4 = 0.1µF, VCC = 3V to 5.5V, TA = -40 to 85°C, unless otherwise specified. Parameter Test Conditions VTIL Input logic threshold low T-IN, FORCEON, FORCEOFF VTIH Input logic threshold high T-IN, FORCEON, FORCEOFF VCC = 3.3V VCC = 5V VTHYS Min. Transmitter input hysteresis Min. Typ. Max. Unit 0.8 V 2 2.4 V V 0.5 V IIL Input leakage current T-IN, FORCEON, FORCEOFF ± 0.01 ± 1.0 µA IOL Output leakage current Receiver Disabled ± 0.05 ± 10 µA VOL Output voltage low IOUT = 1.6mA 0.4 V VOH Output voltage high IOUT = -1mA 6/20 VCC-0.6 VCC-0.1 V ST3243 Table 6. Symbol Electrical characteristics Auto-powerdown electrical characteristics (C1 - C4 = 0.1µF, VCC = 3V to 5.5V, TA = -40 to 85°C, unless otherwise specified. Parameter Test Conditions Min. Typ. Max. Unit 2.7 V V 0.3 V 0.4 V VRITE Receiver input threshold to transmitter enabled Positive threshold Negative threshold 2.7 VRITD Receiver input threshold to transmitter disabled 1µA Supply Current -0.3 VIOL INVALID Output voltage LOW VIOH INVALID Output voltage HIGH tWU Receiver threshold to transmitter enabled IOUT = 1.6mA 250 ms tinvh Receiver positive or negative threshold to INVALID HIGH IOUT = -1mA 1 ms tinvL Receiver positive or negative threshold to INVALID LOW 30 ms Table 7. Symbol VCC-0.6 V Transmitter electrical characteristics (C1 - C4 = 0.1µF, VCC = 3V to 5.5V, TA = -40 to 85°C, unless otherwise specified. Parameter Test Conditions Min. Typ. Max. Unit VTOUT Output voltage swing All transmitter outputs are loaded with 3KΩ to GND ±5 ± 5.4 V ROUT Output Resistance VCC = V+ = V- = 0V, VOUT = ± 2V 300 10M Ω ISC VOT Table 8. Symbol ± 35 Output short circuit current Transmitter output voltage T1IN = T2IN = GND, T3IN = VCC T3OUT loaded with 3KΩ to GND T1OUT and T2OUT loaded with 2.5mA each ± 60 ±5 mA V Receiver electrical characteristics (C1 - C4 = 0.1µF, VCC = 3V to 5.5V, TA = -40 to 85°C, unless otherwise specified. Parameter Test Conditions VRIN Receiver input voltage operating range VRIL RS-232 Input threshold low TA = 25°C, VCC = 3.3V TA = 25°C, VCC = 5.0V VRIH RS-232 Input threshold high TA = 25°C, VCC = 3.3V TA = 25°C, VCC = 5.0V VRIHYS Input hysteresis RRIN Input resistance Min. Typ. -25 0.6 0.8 Max. Unit 25 V 1.2 1.2 1.5 1.8 V 2.4 2.4 0.5 TA = 25°C 3 5 V V 7 KΩ 7/20 Electrical characteristics Table 9. Symbol ST3243 Timing characteristics (C1 - C4 = 0.1µF, VCC = 3V to 5.5V, TA = -40 to 85°C, unless otherwise specified. Parameter Test Conditions RL = 3KΩ, CL= 1000pF one transmitter switching Min. Typ. Max. Unit 250 400 Kbps DR Maximum data rate tPHL tPLH Receiver propagation delay RIN to ROUT, CL = 150pF 0.15 µs Transmitter skew 100 ns 50 ns tT_SKEW tR_SKEW Receiver skew tINVH Receiver positive or negative threshold to INVALID HIGH 1 ms tINVL Receiver positive or negative threshold to INVALID LOW 30 ms SRT 8/20 Transition slew rate TA = 25°C RL = 3K to 7KΩ VCC = 3.3V measured from +3V to -3V or -3V to +3V CL = 150pF to 1000pF CL = 150pF to 2500pF 6 4 30 30 V/µs V/µs ST3243 Application circuits 4 Application circuits Figure 2. Application circuits Table 10. Capacitance value (µF) VCC C1 C2 C3 C4 Cbypass 3.0 to 3.6 0.1 0.1 0.1 0.1 0.1 4.5 to 5.5 0.047 0.33 0.33 0.33 0.33 3.0 to 5.5 0.22 1.0 1.0 1.0 0.22 9/20 Typical performance characteristics 5 ST3243 Typical performance characteristics Unless otherwise specified Tj = 25°C Figure 3. Invalid high threshold time Figure 4. Invalid low threshold time Figure 5. Receiver propagation delay Figure 6. Receiver output enable & disable time 10/20 ST3243 Figure 7. Typical performance characteristics Output current vs output high voltage Figure 8. Output current vs output low voltage 11/20 Package mechanical data 6 ST3243 Package mechanical data In order to meet environmental requirements, ST offers these devices in ECOPACK® packages. These packages have a Lead-free second level interconnect. The category of second level interconnect is marked on the package and on the inner box label, in compliance with JEDEC Standard JESD97. The maximum ratings related to soldering conditions are also marked on the inner box label. ECOPACK is an ST trademark. ECOPACK specifications are available at: www.st.com 12/20 ST3243 Package mechanical data SO-28 MECHANICAL DATA mm. inch DIM. MIN. TYP A MAX. MIN. TYP. 2.65 MAX. 0.104 a1 0.1 0.3 0.004 0.012 b 0.35 0.49 0.014 0.019 b1 0.23 0.32 0.009 0.012 C 0.5 0.020 c1 45° (typ.) D 17.70 18.10 0.697 0.713 E 10.00 10.65 0.393 0.419 e 1.27 0.050 e3 16.51 0.650 F 7.40 7.60 0.291 0.300 L 0.50 1.27 0.020 0.050 S 8 ° (max.) 0016023 13/20 Package mechanical data ST3243 SSOP28 MECHANICAL DATA mm. inch DIM. MIN. TYP A MIN. TYP. 2 A1 0.050 A2 1.65 b MAX. 0.079 0.002 1.85 0.065 0.22 0.38 0.009 0.015 c 0.09 0.25 0.004 0.010 D 9.9 10.2 10.5 0.390 0.402 0.413 E 7.4 7.8 8.2 0.291 0.307 0.323 E1 5 5.3 5.6 0.197 0.209 0.220 e 14/20 MAX. 1.75 0.65 BSC K 0° L 0.55 0.75 0.069 0.073 0.0256 BSC 10° 0° 0.95 0.022 10° 0.030 0.037 ST3243 Package mechanical data TSSOP28 MECHANICAL DATA mm. inch DIM. MIN. TYP A MAX. MIN. TYP. MAX. 1.2 A1 0.05 A2 0.8 b 0.047 0.15 0.002 0.004 0.006 1.05 0.031 0.039 0.041 0.19 0.30 0.007 0.012 c 0.09 0.20 0.004 0.0079 D 9.6 9.7 9.8 0.378 0.382 0.386 E 6.2 6.4 6.6 0.244 0.252 0.260 E1 4.3 4.4 4.48 0.169 0.173 0.176 e 1 0.65 BSC K 0° L 0.45 0.60 0.0256 BSC 8° 0° 0.75 0.018 8° 0.024 0.030 0128292B 15/20 Package mechanical data ST3243 Tape & Reel SO-28 MECHANICAL DATA mm. inch DIM. MIN. A MAX. MIN. 330 13.2 TYP. MAX. 12.992 C 12.8 D 20.2 0.795 N 60 2.362 T 16/20 TYP 0.504 30.4 0.519 1.197 Ao 10.8 11.0 0.425 0.433 Bo 18.2 18.4 0.716 0.724 Ko 2.9 3.1 0.114 0.122 Po 3.9 4.1 0.153 0.161 P 11.9 12.1 0.468 0.476 ST3243 Package mechanical data Tape & Reel SSOP28 MECHANICAL DATA mm. inch DIM. MIN. A TYP MAX. MIN. 330 MAX. 12.992 C 12.8 D 20.2 0.795 N 60 2.362 T 13.2 TYP. 0.504 22.4 0.519 0.882 Ao 8.4 8.6 0.331 0.339 Bo 10.7 10.9 0.421 0.429 Ko 2.9 3.1 0.114 0.122 Po 3.9 4.1 0.153 0.161 P 11.9 12.1 0.468 0.476 17/20 Package mechanical data ST3243 Tape & Reel TSSOP28 MECHANICAL DATA mm. inch DIM. MIN. A MAX. MIN. 330 13.2 TYP. MAX. 12.992 C 12.8 D 20.2 0.795 N 60 2.362 T 18/20 TYP 0.504 22.4 0.519 0.882 Ao 6.8 7 0.268 0.276 Bo 10.1 10.3 0.398 0.406 Ko 1.7 1.9 0.067 0.075 Po 3.9 4.1 0.153 0.161 P 11.9 12.1 0.468 0.476 ST3243 Revision history 7 Revision history Table 11. Revision history Date Revision Changes 19-Sep-2004 6 Document updating. 31-Mar-2006 7 Order codes has been updated and new template. 19/20 ST3243 Please Read Carefully: Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST’s terms and conditions of sale. Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein. UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZE REPRESENTATIVE OF ST, ST PRODUCTS ARE NOT DESIGNED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS, WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY, DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST. ST and the ST logo are trademarks or registered trademarks of ST in various countries. Information in this document supersedes and replaces all information previously supplied. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners. © 2006 STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com 20/20