STMICROELECTRONICS ST3485EBN

ST3485E
3.3V Powered, 15KV ESD protected,
Up to 12Mbps RS-485/RS-422 transceiver
General features
■
ESD protection
– ±15kV human body model
– ±8kV IEC 1000-4-2 contact discharge
■
Operate from a single 3.3V supply - no charge
pump required
■
Interoperable with 5V logic
■
1µA low current shutdown mode max
■
Guaranteed 12Mbps data rate
■
-7 to 12 common mode input voltage range
■
Half duplex versions available
■
Industry standard 75176 pinout
■
Current limiting and thermal shutdown for
driver overload protection
and one receiver in half duplex configuration. The
ST3485E transmits and receives at a guaranteed
data rate of at least 12Mbps.
■
Guaranteed high receiver output state for
floating inputs with no signal present
All transmitter outputs and receiver inputs are
protected to ±15kV using Human Body Model.
■
Allow up to 64 transceivers on the bus
Driver is short-circuit current limited and is
protected against excessive power dissipation by
thermal shutdown circuitry that places the driver
outputs into a high-impedance state.
DIP-8
Description
SO-8
The ST3485E is ±15kV ESD protected, 3.3V low
power transceiver for RS-485 and RS-422
communications. The device contains one driver
Order code
Part number
Temperature range
Package
Comments
ST3485ECN
0 to 70 °C
DIP-8
50parts per tube / 40tube per box
ST3485EBN
-40 to 85 °C
DIP-8
50parts per tube / 40tube per box
ST3485ECDR
0 to 70 °C
SO-8 (Tape & Reel)
2500 parts per reel
ST3485EBDR
-40 to 85 °C
SO-8 (Tape & Reel)
2500 parts per reel
April 2006
Rev 2
1/22
www.st.com
22
Contents
ST3485E
Contents
1
Pin configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
2
Truth tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
3
Maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
4
Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
5
Test circuits and typical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . 9
6
Package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
7
Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
2/22
ST3485E
Pin configuration
1
Pin configuration
Figure 1.
Pin connections
Table 1.
Pin description
Pin n°
Symbol
Name and function
1
RO
Receiver output. If A>B by 200mV, RO will be high; if A<B by 200mV, RO will be low
2
RE
Receiver output enable. RO is enabled when RE is low; RO is high impedance when RE
is high. If RE is high and DE is low, the device will enter a low power shutdown mode.
3
DE
Driver output enable. The driver outputs are enabled by bringing DE high. They are high
impedance when DE is low. If RE is high DE is low, the device will enter a low-power
shutdown mode. If the driver outputs are enabled, the part functions as line driver, while
they are high impedance, it functions as line receivers if RE is low.
4
DI
Driver input. A low on DI forces output A low and output B high. Similarly, a high on DI
forces output A high and output B low
5
GND
6
A
Non-inverting receiver input and non-inverting driver output
7
B
Inverting receiver input and inverting driver output
8
VCC
Ground
Supply voltage: VCC= 3V to 3.6V
3/22
Truth tables
ST3485E
2
Truth tables
Table 2.
Truth table (driver)
Inputs
Outputs
Mode
RE
DE
DI
B
A
X
H
H
L
H
Normal
X
H
L
H
L
Normal
L
L
X
Z
Z
Normal
H
L
X
Z
Z
Shutdown
Note:
X= Don’t care; Z=High impedance
Table 3.
Truth table (receiver)
INPUTS
OUTPUT
MODE
RE
DE
A-B
RO
L
L
≥ 0.2V
H
Normal
L
L
≤ -0.2V
L
Normal
L
L
Inputs Open
H
Normal
H
L
X
Z
Shutdown
Note:
4/22
X= Don’t care; Z=High impedance
ST3485E
Maximum ratings
3
Maximum ratings
Table 4.
Absolute maximum ratings
Symbol
VCC
Parameter
Supply voltage
Value
Unit
7
V
VI
Control input voltage (RE, DE)
-0.3 to 7
V
VDI
Driver input voltage (DI)
-0.3 to 7
V
VDO
Driver output voltage (A, B)
± 14
V
VRI
Receiver input voltage (A, B)
± 14
V
VRO
Receiver output voltage (RO)
-0.3 to (VCC + 0.3)
V
Note:
Absolute Maximum Ratings are those values beyond which damage to the device may
occur. Functional operation under these condition is not implied.
Table 5.
ESD Performance: transmitter outputs, receiver inputs
Symbol
Parameter
Test conditions
Min.
Typ.
Max.
Unit
ESD
ESD Protection voltage
Human body model
± 15
KV
ESD
ESD Protection voltage
IEC-1000-4-2 Contact discharge
±8
KV
5/22
Electrical characteristics
ST3485E
4
Electrical characteristics
Table 6.
Electrical characteristics
VCC = 3V to 3.6V, TA = -40 to 85°C, unless otherwise specified. Typical values are referred
to TA = 25°C)
Symbol
ISUPPLY
ISHDN
Table 7.
Symbol
Parameter
Test conditions
VCC Power supply current No Load, DI=0V or VCC
Shutdown supply current
Parameter
VIH
Input logic threshold high
DE, DI, RE
IIN1
Logic input current
DE, DI, RE
IIN2
Input current (A, B)
DE=0V, VCC= 0 or 3.6V
∆VOD
VOC
Unit
DE=VCC,
RE=0V or VCC
1.3
2.2
mA
DE=0V,
RE=0V
1.2
1.9
mA
0.002
1
µA
Test Conditions
DE, DI, RE
VOD
Max.
Logic input electrical characteristics
VCC = 3V to 3.6V, TA = -40 to 85°C, unless otherwise specified. Typical values are referred
to TA = 25°C)
Input logic threshold low
Symbol
Typ.
DE=0V, RE=VCC, DI=0V or VCC
VIL
Table 8.
Min.
Typ.
Max.
Unit
1.3
0.8
V
2
V
± 2.0
µA
VIN=12V
1
mA
VIN=-7V
-0.8
mA
Transmitter electrical characteristics
VCC = 3V to 3.6V, TA = -40 to 85°C, unless otherwise specified. Typical values are referred
to Ta = 25°C)
Parameter
Differential drive output
Test conditions
Typ.
Max.
Unit
2
V
RL= 54Ω (RS-485) (Figure 1.)
1.5
V
RL= 60Ω (RS-485) (Figure 2.)
1.5
V
Change in magnitude of driver
differential output voltage for
RL= 54Ω or 100Ω (Figure 1.)
complementary output states
(Note: 1)
Driver common mode output
voltage
Min.
RL= 100Ω (RS-422) (Figure 1.)
RL= 54Ω or 100Ω (Figure 1.)
∆VOC
Change in magnitude of driver
common mode output voltage RL= 54Ω or 100Ω (Figure 1.)
(Note: 1)
IOSD
Driver short circuit output
current
6/22
Min.
0.2
V
3
V
0.2
V
± 250
mA
ST3485E
Table 9.
Symbol
Electrical characteristics
Receiver electrical characteristics
VCC = 3V to 3.6V, TA = -40 to 85°C, unless otherwise specified. Typical values are referred
to Ta = 25°C)
Parameter
Test Conditions
Min.
Typ.
Max.
Unit
0.2
V
Receiver differential
threshold voltage
VCM = -7V to 12V, DE = 0
∆VTH
Receiver input hysteresis
VCM = 0V
VOH
Receiver output high
voltage
IOUT = -4mA, VID = 200mV
(Figure 8. and Figure 9.)
VOL
Receiver output low
voltage
IOUT = 4mA, VID = -200mV, (Figure 3.)
0.4
V
IOZR
3-State (high impedance)
output current at receiver
VCC = 3.6VVO = 0V to VCC
±1
µA
RRIN
Receiver input resistance
VCM = -7V to 12V
24
IOSR
Receiver short-circuit
current
VRO = 0V to VCC
7
VTH
Table 10.
Symbol
-0.2
70
V
2
V
KΩ
60
mA
Driver switching characteristics
VCC = 3V to 3.6V, TA = -40 to 85°C, unless otherwise specified. Typical values are referred
to Ta = 25°C)
Parameter
Test Conditions
Min.
Typ.
12
15
Max.
Unit
DR
Maximum data rate
Mbps
tDD
Differential output delay
RL= 60Ω, CL = 15pF, (Figure 4. and
Figure 5.)
18
30
ns
tTD
Differential output
transition time
RL= 60Ω, CL = 15pF, (Figure 4. and
Figure 5.)
12
20
ns
tPLH
tPHL
Propagation delay
RL= 27Ω, CL = 15pF, (Figure 8. and
Figure 9.)
18
30
ns
tPDS
|tPLH - tPHL| Propagation
delay skew (Note 2)
RL= 27Ω, CL = 15pF, (Figure 8. and
Figure 9.)
2
5
ns
tPZL
Output enable time
RL= 110Ω, (Figure 10. and Figure 11.)
19
35
ns
tPZH
Output enable time
RL= 110Ω, (Figure 6. and Figure 7.)
30
50
ns
tPHZ
Output disable time
RL= 110Ω, (Figure 6. and Figure 7.)
19
35
ns
tPLZ
Output disable time
RL= 110Ω, (Figure 10. and Figure 11.)
30
50
ns
tSKEW
Differential output delay
skew
1
3
ns
tZH(SHDN)
Driver enable from
shutdown to output high
30
50
ns
tZL(SHDN)
Driver enable from
shutdown to output low
19
35
ns
7/22
Electrical characteristics
Table 11.
Symbol
ST3485E
Receiver switching characteristics
VCC = 3V to 3.6V, TA = -40 to 85°C, unless otherwise specified. Typical values are referred
to Ta = 25°C)
Parameter
Test Conditions
Min.
Typ.
Max.
Unit
Propagation delay
VID =0V to 3V, CL1 = 15pF
(Figure 12. and Figure 13.)
30
50
ns
|tPLH - tPHL| Propagation
delay skew
VID =0V to 3V, CL1 = 15pF
(Figure 12. and Figure 13.)
1
3
ns
tPZL
Output enable time
CRL = 15pF, (Figure 14. and Figure 18.)
10
20
ns
tPZH
Output enable time
CRL = 15pF, (Figure 14. and Figure 18.)
10
20
ns
tPHZ
Output disable time
CRL = 15pF, (Figure 14. and Figure 18.)
10
20
ns
tPLZ
Output disable time
CRL = 15pF, (Figure 14. and Figure 18.)
10
20
ns
tZH(SHDN)
Receiver enable from
shutdown to output high
CRL = 15pF, (Figure 14. and Figure 18.)
10
20
ns
tZL(SHDN)
Receiver enable from
shutdown to output low
CRL = 15pF, (Figure 14. and Figure 18.)
20
40
µs
tPLH
tPHL
tRPDS
Note:
8/22
1
∆VOD and ∆VOC are the changes in VOD and VOC, respectively, when the DI input changes
state.
2
Measured on |tPLH(A)-tPHL(A)| and |tPLH(B)-tPHL(B)|
3
The transceivers are put into shutdown by bring RE high and DE low. If the input are in state
for less than 80ns, the part are guaranteed not to enter shutdown. If the inputs are in this
state for at least 300ns, the parts are guaranteed to have entered shutdown.
ST3485E
Test circuits and typical characteristics
5
Test circuits and typical characteristics
Figure 2.
Driver and VOC test load
Figure 3.
Driver VOD with varying common mode voltage test load
Figure 4.
Receiver VOH and VOL test circuit
9/22
Test circuits and typical characteristics
Figure 5.
Drive differential output delay transition time test circuit
Figure 6.
Drive differential output delay transition time waveform
Figure 7.
Drive enable and disable times test circuit
10/22
ST3485E
ST3485E
Test circuits and typical characteristics
Figure 8.
Drive enable and disable times waveforms
Figure 9.
Drive propagation time test circuit
Figure 10. Drive propagation time waveform
11/22
Test circuits and typical characteristics
Figure 11. Drive enable and disable times test circuit
Figure 12. Drive enable and disable times waveforms
Figure 13. Receiver propagation delay time test circuit
12/22
ST3485E
ST3485E
Test circuits and typical characteristics
Figure 14. Receiver propagation delay time waveforms
Figure 15. Receiver enable and disable times test circuit
Figure 16. Receiver enable and disable times waveform
13/22
Test circuits and typical characteristics
Figure 17. Receiver enable and disable times waveform
Figure 18. Receiver enable and disable times waveform
Figure 19. Receiver enable and disable times waveform
14/22
ST3485E
ST3485E
Test circuits and typical characteristics
Figure 20. Receiver output current vs output
low voltage
Figure 21. Receiver output current vs output
high voltage
Figure 22. Low level driver output capability
Figure 23. High level driver output capability
Figure 24. Receiver input characteristics
Figure 25. Driver short circuit current
15/22
Test circuits and typical characteristics
Figure 26. Driver short circuit current
16/22
ST3485E
ST3485E
6
Package mechanical data
Package mechanical data
In order to meet environmental requirements, ST offers these devices in ECOPACK®
packages. These packages have a Lead-free second level interconnect. The category of
second level interconnect is marked on the package and on the inner box label, in
compliance with JEDEC Standard JESD97. The maximum ratings related to soldering
conditions are also marked on the inner box label. ECOPACK is an ST trademark.
ECOPACK specifications are available at: www.st.com
17/22
Package mechanical data
ST3485E
Plastic DIP-8 MECHANICAL DATA
mm.
inch
DIM.
MIN.
A
TYP
MAX.
MIN.
3.3
TYP.
MAX.
0.130
a1
0.7
B
1.39
1.65
0.055
0.065
B1
0.91
1.04
0.036
0.041
b
b1
0.028
0.5
0.38
0.020
0.5
D
0.015
0.020
9.8
0.386
E
8.8
0.346
e
2.54
0.100
e3
7.62
0.300
e4
7.62
0.300
F
7.1
0.280
I
4.8
0.189
L
Z
3.3
0.44
0.130
1.6
0.017
0.063
P001F
18/22
ST3485E
Package mechanical data
SO-8 MECHANICAL DATA
DIM.
mm.
MIN.
TYP
inch
MAX.
MIN.
TYP.
MAX.
A
1.35
1.75
0.053
0.069
A1
0.10
0.25
0.04
0.010
A2
1.10
1.65
0.043
0.065
B
0.33
0.51
0.013
0.020
C
0.19
0.25
0.007
0.010
D
4.80
5.00
0.189
0.197
E
3.80
4.00
0.150
0.157
e
1.27
0.050
H
5.80
6.20
0.228
0.244
h
0.25
0.50
0.010
0.020
L
0.40
1.27
0.016
0.050
k
ddd
8° (max.)
0.1
0.04
0016023/C
19/22
Package mechanical data
ST3485E
Tape & Reel SO-8 MECHANICAL DATA
mm.
inch
DIM.
MIN.
A
MAX.
MIN.
330
13.2
TYP.
MAX.
12.992
C
12.8
D
20.2
0.795
N
60
2.362
T
20/22
TYP
0.504
22.4
0.519
0.882
Ao
8.1
8.5
0.319
0.335
Bo
5.5
5.9
0.216
0.232
Ko
2.1
2.3
0.082
0.090
Po
3.9
4.1
0.153
0.161
P
7.9
8.1
0.311
0.319
ST3485E
Revision history
7
Revision history
Table 12.
Revision history
Date
Revision
Changes
20-Jun-2005
2
Mistake on table 12 tZL(SHDN) ms ==> µs.
30-Aug-2005
3
Remove (TRUE) on title, description has been updated in cover page.
The VTH and ∆VTH values are changed in table 10.
07-Apr-2006
4
Order codes has been updated and new template.
21/22
ST3485E
Please Read Carefully:
Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the
right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any
time, without notice.
All ST products are sold pursuant to ST’s terms and conditions of sale.
Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no
liability whatsoever relating to the choice, selection or use of the ST products and services described herein.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this
document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products
or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such
third party products or services or any intellectual property contained therein.
UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED
WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS
OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.
UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZE REPRESENTATIVE OF ST, ST PRODUCTS ARE NOT DESIGNED,
AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING APPLICATIONS,
NOR IN PRODUCTS OR SYSTEMS, WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY, DEATH, OR
SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE.
Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void
any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any
liability of ST.
ST and the ST logo are trademarks or registered trademarks of ST in various countries.
Information in this document supersedes and replaces all information previously supplied.
The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.
© 2006 STMicroelectronics - All rights reserved
STMicroelectronics group of companies
Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America
www.st.com
22/22