ST619LB DC-DC converter regulated 5 V charge pump Features ■ Regulated 5 V ±4 % charge pump ■ Output current guaranteed over temperature: 20 mA (VI ≥ 2 V), 30 mA (VI ≥ 3 V) ■ No inductors; very low EMI noise ■ Uses small, inexpensive capacitors ■ Logic controlled 1 µA max shut-down supply current ■ Shut down disconnects load from input ■ Available in SO-8 and DIP-8 packages SO-8 Description The ST619LB is a step-up charge pump DC-DC converter which delivers a regulated 5 V ±4 % output at 30 mA and over temperature. The input voltage range is 2 V to 3.6 V (two battery cells). It requires only four external capacitor: two 0.22 µF flying capacitors, and 10 µF capacitors at the input and output. Low operating supply current (typ. 200 µA) make the device ideal for small, portable and battery powered applications. When shut down the load is disconnected from the input and the supply current is typically 0.02 µA. The ST619LB is available in SO-8 package. Table 1. Device summary November 2007 Order codes SO-8 (tape & reel) ST619LB ST619LBDR Rev. 4 1/16 www.st.com 16 ST619LB Contents 1 Schematic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 Pin configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 3 Operating principle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 3.1 Shut down mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 4 Maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 5 Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 6 Typical performance characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 7 Application information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 7.1 Charge pump capacitors C1 and C2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 7.2 Input and output capacitors C3 and C4 . . . . . . . . . . . . . . . . . . . . . . . . . . 10 7.3 Layout consideration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 8 Package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 9 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 2/16 ST619LB Schematic 1 Schematic Figure 1. Schematic diagram 3/16 Pin configuration ST619LB 2 Pin configuration Figure 2. Pin connections (top view) Table 2. Pin description Pin n° Symbol 1 C1+ 2 IN 3 OUT 5V output voltage. VO=0V when in shutdown mode. 4 C2+ Positive terminal for the second charge pump capacitor 5 C2- Negative terminal for the second charge pump capacitor 6 GND 7 SHDN 8 C1- 4/16 Name and function Positive terminal for the first charge pump capacitor Input supply voltage Ground Active high C-MOS logic level shutdown input. SHDN is connected to GND for normal operation. Negative terminal for the first charge pump capacitor ST619LB 3 Operating principle Operating principle The ST619LB is able to provide a regulated 5 V output from a 2 V to 3.6 V (two battery cells) input. Internal charge pump and external capacitors generate the 5 V output, eliminating the need for inductors. The output voltage is regulated to 5 V, ±4 % by a pulse skipping controller that turns on the charge pump when the output voltage begins to drop. To maintain the greatest efficiency the internal charge pump of the device operates as a voltage doubler when VI ranges from 3.0 V to 3.6 V and as a voltage triple when VI ranges from 2.0 V to 2.5 V. When VI ranges from 2.5 V to 3.0 V, the ST619LB switches between doubler and triple mode on alternating cycles, making a 2.5 x VI charge pump. To further enhance the efficiency over the input range, an internal comparator selects the higher of VI or VO to run the ST619LB's circuitry. With VI = 2 V and IO = 20 mA the typical efficiency value is 80%. In triple mode (see block diagram), when the S1 switches close, the S2 switches open and capacitors C1 and C2 charge up to VI. On the second half of the cycle, C1 and C2 are connected in series between IN and OUT when the S1 switches open and S2 switches close. In the doubler mode only C2 is used. During one oscillator cycle, energy is transferred from the input to the charge pump capacitors, and then from the charge pump capacitors to the output capacitors and load. The number of cycles within a given time frame increases as the load increases or as the input supply voltage decreases. In the limiting case, the charge pumps operate continuously, and the oscillator frequency is nominally 500 kHz. 3.1 Shut down mode The ST619LB enters low power shut down mode when SHDN is a logic high. In shut down mode, OUT is disconnected from the IN and VO falls to 0V. The SHDN pin is connected to ground for normal operation. SHDN is a CMOS compatible input. 5/16 Maximum ratings ST619LB 4 Maximum ratings Table 3. Absolute maximum ratings Symbol Parameter Value Unit VI DC input voltage -0.3 to 5.5 V VO Output voltage -0.3 to 5.5 V -0.3 to (VI + 0.3) V VSHDN Shutdown input voltage IO Output current continuous 120 mA TSTG Storage temperature range -55 to +150 °C TOP Operating junction temperature range -40 to +85 °C Note: Absolute maximum ratings are those values beyond which damage to the device may occur. Functional operation under these condition is not implied. Table 4. Thermal data Symbol RthJA Parameter Thermal resistance junction-ambient (1) 1. This value depends from thermal design of PCB on which the device is mounted. 6/16 SO-8 Unit 160 °C/W ST619LB Electrical characteristics 5 Electrical characteristics Table 5. Electrical characteristics (VI = 2 to 3.6 V, C1 = C2 = 0.22 µF, C3 = C4 = 10 µF, TA = -40 to 85°C, unless otherwise specified. Typical value are referred at TA = 25 °C) Symbol Parameter VI Input voltage VO Output voltage VRIPPLE Output voltage ripple Ii ISHDN ν No load supply current Shutdown supply current Efficiency fOSC Switching frequency VIH SHDN input threshold VIL SHDN input threshold IIH SHDN input current Note: Test conditions Min. Typ. 2 Max. Unit 3.6 V VI = 2 to 3.6V, IO =0 to 20mA 4.8 5 5.2 V VI = 3 to 3.6V, IO=0 to 30mA 4.8 5 5.2 V No load, Full load 100 mV VI = 2 to 3V, No load 200 300 VI = 3 to 3.6V, No load 75 150 0.02 1 µA VI = 2 to 3.6V, No Load, VSHDN = VI VI = 3V, IO =20mA 82 VI = 3V, IO =30mA 82 VI = 2V, IO =20mA 80 Full load 500 % kHz 0.7VI VSHDN = VI µA V 0.005 0.4 V ±1 µA Do not overload or short the output to ground. If the above conditions are not observed the device may be damaged. 7/16 Typical performance characteristics ST619LB 6 Typical performance characteristics Figure 3. No load supply current vs input voltage Figure 4. Shutdown supply current vs input voltage Figure 5. Maximum output current vs input voltage Figure 6. Output voltage vs output current Figure 7. Efficiency vs output current Figure 8. Efficiency vs input voltage 8/16 ST619LB Figure 9. Typical performance characteristics Output voltage vs input voltage Figure 11. Output voltage vs temperature Figure 10. Start-up Figure 12. Line transient response RL = 250 Ω Figure 13. Load transient response VI = 3 V, IO = 0 to 25 mA 9/16 Application information 7 Application information 7.1 Charge pump capacitors C1 and C2 ST619LB The values of charge pump capacitors C1 and C2 are critical to ensure adequate output current and avoid excessive peak currents. It is suggested to use values in the range of 0.22 µF to 1.0 µF and avoid the use of higher values of CO capacitors, in order to obtain best performance. Ceramic or tantalum capacitors are recommended. 7.2 Input and output capacitors C3 and C4 The type of input capacitor (C3) and output filter capacitor (C4) used is not critical, but it does affect performance. Tantalum, ceramics or aluminium electrolytic are suggested. For lowest ripple, use large, low effective series resistance (ESR) ceramic tantalum capacitors. If the input supply source impedance is very low, C3 can be omitted. The typical application circuit shows the component values for proper operation using minimal board space. The input bypass capacitor (C3) and output filter capacitor (C4) should be at least 10 µF. Many capacitors exhibit 40% to 50% variation over temperature. Compensate for capacitor temperature coefficient by selecting a large nominal value to ensure proper operation over temperature. 7.3 Layout consideration In the below figure, the typical application evaluation board of ST619LB is reported. A good layout ensures stability and helps maintain the output voltage under heavy loads. For best performance, use very short connections to the capacitors. Figure 14. Typical application circuit 10/16 ST619LB Application information Figure 15. Typical application evaluation board 11/16 Package mechanical data 8 ST619LB Package mechanical data In order to meet environmental requirements, ST offers these devices in ECOPACK® packages. These packages have a Lead-free second level interconnect. The category of second Level Interconnect is marked on the package and on the inner box label, in compliance with JEDEC Standard JESD97. The maximum ratings related to soldering conditions are also marked on the inner box label. ECOPACK is an ST trademark. ECOPACK specifications are available at: www.st.com. 12/16 ST619LB Package mechanical data SO-8 mechanical data Dim. mm. Min. Typ. inch. Max. Min. Typ. Max. A 1.35 1.75 0.053 0.069 A1 0.10 0.25 0.04 0.010 A2 1.10 1.65 0.043 0.065 B 0.33 0.51 0.013 0.020 C 0.19 0.25 0.007 0.010 D 4.80 5.00 0.189 0.197 E 3.80 4.00 0.150 0.157 e 1.27 0.050 H 5.80 6.20 0.228 0.244 h 0.25 0.50 0.010 0.020 L 0.40 1.27 0.016 0.050 k ddd 8° (max.) 0.1 0.04 0016023/C 13/16 Package mechanical data ST619LB Tape & reel SO-8 mechanical data mm. inch. Dim. Min. A Max. Min. 330 13.2 Typ. Max. 12.992 C 12.8 D 20.2 0.795 N 60 2.362 T 14/16 Typ. 0.504 22.4 0.519 0.882 Ao 8.1 8.5 0.319 0.335 Bo 5.5 5.9 0.216 0.232 Ko 2.1 2.3 0.082 0.090 Po 3.9 4.1 0.153 0.161 P 7.9 8.1 0.311 0.319 ST619LB Revision history 9 Revision history Table 6. Document revision history Date Revision 21-Jun-2004 3 07-Nov-2007 4 Changes Added Table 1. 15/16 ST619LB Please Read Carefully: Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST’s terms and conditions of sale. Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein. UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY, DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK. Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST. ST and the ST logo are trademarks or registered trademarks of ST in various countries. Information in this document supersedes and replaces all information previously supplied. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners. © 2007 STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com 16/16