STMICROELECTRONICS ST72216GX-AUTO

ST72104Gx-Auto, ST72215Gx-Auto,
ST72216Gx-Auto, ST72254Gx-Auto
8-bit MCU for automotive with single voltage Flash/ROM memory,
ADC, 16-bit timers, SPI, I2C interfaces
■
■
■
■
■
Memories
– 4K or 8K bytes Program memory (ROM and
single voltage Flash) with readout protection
and in-situ programming (remote ISP)
– 256 bytes RAM
Clock, Reset and Supply Management
– Enhanced reset system
– Enhanced low voltage supply supervisor with
3 programmable levels
– Clock sources: crystal/ceramic resonator oscillators or RC oscillators, external clock,
backup Clock Security System
– Clock-out capability
– 3 Power Saving Modes: Halt, Wait and Slow
Interrupt Management
– 7 interrupt vectors plus TRAP and RESET
– 22 external interrupt lines (on 2 vectors)
22 I/O Ports
– 22 multifunctional bidirectional I/O lines
– 14 alternate function lines
– 8 high sink outputs
3 Timers
– Configurable watchdog timer
– Two 16-bit timers with: 2 input captures, 2 output compares, external clock input on one timer, PWM and Pulse generator modes (one
only on ST72104Gx-Auto and ST72216G1Auto)
SO28
■
■
■
■
2 Communications Interfaces
– SPI synchronous serial interface
– I2C multimaster interface
(only on ST72254Gx-Auto)
1 Analog Peripheral
– 8-bit ADC with 6 input channels
(except on ST72104Gx-Auto)
Instruction Set
– 8-bit data manipulation
– 63 basic instructions
– 17 main addressing modes
– 8 x 8 unsigned multiply instruction
– True bit manipulation
Development Tools
– Full hardware/software development package
Device Summary
ST72104G1- ST72104G2- ST72216G1- ST72215G2- ST72254G1- ST72254G2Auto
Auto
Auto
Auto
Auto
Auto
Program memory Flash/ROM 4 Kbytes
8 Kbytes
4 Kbytes
8 Kbytes
4 Kbytes
8 Kbytes
RAM (stack)
256 (128) bytes
Watchdog timer
One 16-bit timer
Two 16-bit timers
Peripherals
SPI
ADC
I2C
Operating Supply
3.2V to 5.5 V
CPU Frequency
Up to 8 MHz (with oscillator up to 16 MHz)
Operating Temperature
-40°C to +85°C / -40°C to +105°C / -40°C to +125C°
Packages
SO28
Features
Rev. 1
October 2007
1/135
1
Table of Contents
1 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2 PIN DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
3 REGISTER AND MEMORY MAP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
4 FLASH PROGRAM MEMORY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
4.1 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
4.2
MAIN FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
4.3
STRUCTURAL ORGANIZATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
4.4
IN-SITU PROGRAMMING (ISP) MODE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
4.5
MEMORY READOUT PROTECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
5 CENTRAL PROCESSING UNIT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
5.1 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
5.2
MAIN FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
5.3
CPU REGISTERS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
6 SUPPLY, RESET AND CLOCK MANAGEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
6.1 LOW VOLTAGE DETECTOR (LVD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
6.2
RESET SEQUENCE MANAGER (RSM) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
6.2.1
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.2.2
Asynchronous External RESET pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.2.3
Internal Low Voltage Detection RESET . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.2.4
Internal Watchdog RESET . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.3 MULTI-OSCILLATOR (MO) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.4
CLOCK SECURITY SYSTEM (CSS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
6.4.1
Clock Filter Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.4.2
Safe Oscillator Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.4.3
Low Power Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.4.4
Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.5 CLOCK RESET AND SUPPLY REGISTER DESCRIPTION (CRSR) . . . . . . . . . . . . . . .
6.6
19
20
20
20
21
22
22
22
22
23
MAIN CLOCK CONTROLLER (MCC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
7 INTERRUPTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
7.1 NON-MASKABLE SOFTWARE INTERRUPT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
7.2
EXTERNAL INTERRUPTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
7.3
PERIPHERAL INTERRUPTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
8 POWER SAVING MODES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
8.1 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
8.2
SLOW MODE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
8.3
WAIT MODE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
8.4
HALT MODE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
9 I/O PORTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
9.1 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
9.2
FUNCTIONAL DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
9.2.1
Input Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9.2.2
Output Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135
....
9.2.3
Alternate Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9.3 I/O PORT IMPLEMENTATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2/135
2
30
30
30
33
Table of Contents
9.4
LOW POWER MODES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
9.5
INTERRUPTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
9.6
REGISTER DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
10 MISCELLANEOUS REGISTERS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
10.1 I/O PORT INTERRUPT SENSITIVITY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
10.2 I/O PORT ALTERNATE FUNCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
10.3 MISCELLANEOUS REGISTER DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
11 ON-CHIP PERIPHERALS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
11.1 WATCHDOG TIMER (WDG) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
11.1.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11.1.2 Main Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11.1.3 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11.1.4 Hardware Watchdog Option . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11.1.5 Low Power Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11.1.6 Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11.1.7 Register Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11.2 16-BIT TIMER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
39
39
39
40
40
40
40
42
11.2.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11.2.2 Main Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11.2.3 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11.2.4 Low Power Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11.2.5 Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11.2.6 Summary of Timer Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11.2.7 Register Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11.3 SERIAL PERIPHERAL INTERFACE (SPI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
42
42
42
54
54
54
55
60
11.3.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11.3.2 Main Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11.3.3 General description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11.3.4 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11.3.5 Low Power Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11.3.6 Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11.3.7 Register Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11.4 I2C BUS INTERFACE (I2C) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
60
60
60
62
69
69
70
73
11.4.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11.4.2 Main Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11.4.3 General Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11.4.4 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11.4.5 Low Power Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11.4.6 Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11.4.7 Register Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11.5 8-BIT A/D CONVERTER (ADC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
73
73
73
75
79
79
80
85
11.5.1
11.5.2
11.5.3
11.5.4
11.5.5
11.5.6
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Main Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Low Power Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Register Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
85
85
85
86
86
87
3/135
3
Table of Contents
12 INSTRUCTION SET . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
12.1 ST7 ADDRESSING MODES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
12.1.1 Inherent . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
12.1.2 Immediate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
12.1.3 Direct . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
12.1.4 Indexed (No Offset, Short, Long) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
12.1.5 Indirect (Short, Long) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
12.1.6 Indirect Indexed (Short, Long) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
12.1.7 Relative Mode (Direct, Indirect) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
12.2 INSTRUCTION GROUPS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
90
90
90
90
90
91
91
92
13 ELECTRICAL CHARACTERISTICS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
13.1 PARAMETER CONDITIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
13.1.1 Minimum and Maximum Values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
13.1.2 Typical Values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
13.1.3 Typical Curves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
13.1.4 Loading Capacitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
13.1.5 Pin Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
13.2 ABSOLUTE MAXIMUM RATINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
95
95
95
95
95
96
13.2.1 Voltage Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
13.2.2 Current Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
13.2.3 Thermal Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
13.3 OPERATING CONDITIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
96
96
96
97
13.3.1 General Operating Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
13.3.2 Operating Conditions with Low Voltage Detector (LVD) . . . . . . . . . . . . . . . . . . . . 99
13.4 SUPPLY CURRENT CHARACTERISTICS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
13.4.1 RUN and SLOW Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
13.4.2 WAIT and SLOW WAIT Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
13.4.3 HALT Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
13.4.4 Supply and Clock Managers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
13.4.5 On-Chip Peripherals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
13.5 CLOCK AND TIMING CHARACTERISTICS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
101
102
103
103
103
104
13.5.1 General Timings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
13.5.2 External Clock Source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
13.5.3 Crystal and Ceramic Resonator Oscillators . . . . . . . . . . . . . . . . . . . . . . . . . . . .
13.5.4 RC Oscillators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
13.5.5 Clock Security System (CSS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
13.6 MEMORY CHARACTERISTICS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
104
104
105
108
109
110
13.6.1 RAM and Hardware Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110
13.6.2 Flash Program Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110
13.7 EMC CHARACTERISTICS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111
13.7.1 Functional EMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
13.7.2 Absolute Electrical Sensitivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
13.7.3 ESD Pin Protection Strategy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
13.8 I/O PORT PIN CHARACTERISTICS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
111
112
114
116
13.8.1 General Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135
. . . 116
13.8.2 Output Driving Current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117
13.9 CONTROL PIN CHARACTERISTICS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119
4/135
Table of Contents
13.9.1 Asynchronous RESET Pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119
13.9.2 ISPSEL Pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121
13.10 TIMER PERIPHERAL CHARACTERISTICS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122
13.10.1 Watchdog Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122
13.10.2 16-Bit Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122
13.11 COMMUNICATION INTERFACE CHARACTERISTICS . . . . . . . . . . . . . . . . . . . . . . . . 123
13.11.1 SPI - Serial Peripheral Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123
13.11.2 I2C - Inter IC Control Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125
13.12 8-BIT ADC CHARACTERISTICS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126
14 PACKAGE CHARACTERISTICS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128
14.1 PACKAGE MECHANICAL DATA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128
14.2 ECOPACK® . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128
14.3 THERMAL CHARACTERISTICS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128
15 DEVICE CONFIGURATION AND ORDERING INFORMATION . . . . . . . . . . . . . . . . . . . . . . . 129
15.1 OPTION BYTES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129
15.2 DEVICE ORDERING INFORMATION AND TRANSFER OF CUSTOMER CODE . . . . 130
15.3 DEVELOPMENT TOOLS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132
15.3.1 Package/Socket Footprint Proposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133
15.4 ST7 APPLICATION NOTES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133
16 SUMMARY OF CHANGES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 134
5/135
ST72104Gx-Auto, ST72215Gx-Auto, ST72216Gx-Auto, ST72254Gx-Auto
1 INTRODUCTION
The
ST72104G-Auto,
ST72215G-Auto,
ST72216G-Auto and ST72254G-Auto devices are
members of the ST7 microcontroller family. They
can be grouped as follows:
– ST72254G-Auto devices are designed for midrange applications with ADC and I²C interface
capabilities.
– ST72215/6G-Auto devices target the same
range of applications but without I²C interface.
– ST72104G-Auto devices are for applications that
do not need ADC and I²C peripherals.
All devices are based on a common industrystandard 8-bit core, featuring an enhanced instruction set.
The ST72C104G, ST72C215G, ST72C216G and
ST72C254G versions feature single-voltage Flash
memory with byte-by-byte In-Situ Programming
(ISP) capability.
Under software control, all devices can be placed
in WAIT, SLOW, or HALT mode, reducing power
consumption when the application is in idle or
standby state.
The enhanced instruction set and addressing
modes of the ST7 offer both power and flexibility to
software developers, enabling the design of highly
efficient and compact application code. In addition
to standard 8-bit data management, all ST7 microcontrollers feature true bit manipulation, 8x8 unsigned multiplication and indirect addressing
modes.
For easy reference, all parametric data are located
in Section 13 on page 95.
Figure 1. General Block Diagram
OSC1
OSC2
MULTI OSC
+
CLOCK FILTER
INTERNAL
CLOCK
I2C
PORT A
PA7:0
(8 bits)
LVD
VDD
RESET
CONTROL
8-BIT CORE
ALU
PROGRAM
MEMORY
(4 or 8K bytes)
RAM
(256 bytes)
6/135
4
SPI
ADDRESS AND DATA BUS
VSS
POWER
SUPPLY
PORT B
PB7:0
(8 bits)
16-BIT TIMER A
PORT C
8-BIT ADC
16-BIT TIMER B
WATCHDOG
PC5:0
(6 bits)
ST72104Gx-Auto, ST72215Gx-Auto, ST72216Gx-Auto, ST72254Gx-Auto
2 PIN DESCRIPTION
Figure 2. 28-Pin SO Package Pinout
RESET
1
28
VDD
OSC1
OSC2
2
27
3
26
VSS
ISPSEL
SS/PB7
4
25
PA0 (HS)
ISPCLK/SCK/PB6
5
24
PA1 (HS)
ISPDATA/MISO/PB5
6
23
PA2 (HS)
MOSI/PB4
7
OCMP2_A/PB3
8
ICAP2_A/PB2
ei1
ei0
22
PA3 (HS)
21
PA4 (HS)/SCLI
9
20
PA5 (HS)
OCMP1_A/PB1
ICAP1_A/PB0
10
19
11
18
PA6 (HS)/SDAI
PA7 (HS)
AIN5/EXTCLK_A/PC5
AIN4/OCMP2_B/PC4
12
17
13
14
ei0 or ei1 16
15
AIN3/ICAP2_B/PC3
PC0/ICAP1_B/AIN0
PC1/OCMP1_B/AIN1
PC2/MCO/AIN2
(HS) 20mA high sink capability
eiX associated external interrupt vector
7/135
5
ST72104Gx-Auto, ST72215Gx-Auto, ST72216Gx-Auto, ST72254Gx-Auto
PIN DESCRIPTION (Cont’d)
For external pin connection guidelines, refer to Section 13 "ELECTRICAL CHARACTERISTICS" on page
95.
Legend / Abbreviations for Table 1:
Type:
I = input, O = output, S = supply
Input level:
A = Dedicated analog input
In/Output level: C = CMOS 0.3VDD/0.7VDD,
CT= CMOS 0.3VDD/0.7VDD with input trigger
Output level:
HS = 20mA high sink (on N-buffer only)
Port and control configuration:
– Input:
float = floating, wpu = weak pull-up, int = interrupt 1), ana = analog
– Output:
OD = open drain 2), PP = push-pull
Refer to Section 9 "I/O PORTS" on page 30 for more details on the software configuration of the I/O ports.
The RESET configuration of each pin is shown in bold. This configuration is valid as long as the device is
in reset state.
Table 1. SO28 Device Pin Description
I/O CT
PP
X
Main
Function
(after reset)
Alternate Function
RESET
2
OSC1 3)
I
3
OSC2 3)
O
4
PB7/SS
I/O
CT
X
ei1
X
X
Port B7
SPI Slave Select (active low)
5
PB6/SCK/ISPCLK
I/O
CT
X
ei1
X
X
Port B6
SPI Serial Clock or ISP Clock
6
PB5/MISO/ISPDATA I/O
CT
X
ei1
X
X
Port B5
SPI Master In/ Slave Out Data or
ISP Data
7
PB4/MOSI
I/O
CT
X
ei1
X
X
Port B4
SPI Master Out / Slave In Data
8
PB3/OCMP2_A
I/O
CT
X
ei1
X
X
Port B3
Timer A Output Compare 2
9
PB2/ICAP2_A
I/O
CT
X
ei1
X
X
Port B2
Timer A Input Capture 2
10 PB1 /OCMP1_A
I/O
CT
X
ei1
X
X
Port B1
Timer A Output Compare 1
11 PB0 /ICAP1_A
I/O
CT
X
ei1
X
X
Port B0
Timer A Input Capture 1
12 PC5/EXTCLK_A/AIN5 I/O
CT
X ei0/ei1
X
X
Port C5
13 PC4/OCMP2_B/AIN4 I/O
CT
X ei0/ei1
X
X
Port C4
14 PC3/ ICAP2_B/AIN3
I/O
CT
X ei0/ei1 X
X
X
Port C3
15 PC2/MCO/AIN2
I/O
CT
X ei0/ei1 X
X
X
Port C2
16 PC1/OCMP1_B/AIN1 I/O
CT
X ei0/ei1 X
X
X
Port C1
17 PC0/ICAP1_B/AIN0
CT
X ei0/ei1 X
X
X
Port C0
I/O
X
OD
ana
int
wpu
float
Output
Port / Control
Input
Output
1
8/135
6
Name
Input
No.
Level
Type
Pin
Top priority non maskable interrupt (active low)
External clock input or Resonator oscillator inverter
input or resistor input for RC oscillator
Resonator oscillator inverter output or capacitor input for RC oscillator
Timer A Input Clock or ADC Analog
Input 5
Timer B Output Compare 2 or ADC
Analog Input 4
Timer B Input Capture 2 or ADC Analog Input 3
Main clock output (fCPU) or ADC
Analog Input 2
Timer B Output Compare 1 or ADC
Analog Input 1
Timer B Input Capture 1 or ADC Analog Input 0
ST72104Gx-Auto, ST72215Gx-Auto, ST72216Gx-Auto, ST72254Gx-Auto
X
X
Port A7
19 PA6 /SDAI
I/O CT HS
X
20 PA5
I/O CT HS
X
21 PA4 /SCLI
I/O CT HS
X
22 PA3
I/O CT HS
X
ei0
X
X
Port A3
23 PA2
I/O CT HS
X
ei0
X
X
Port A2
24 PA1
I/O CT HS
X
ei0
X
X
Port A1
25 PA0
I/O CT HS
X
ei0
X
X
Port A0
C
X
ei0
ei0
ei0
ei0
ana
X
int
I/O CT HS
Name
wpu
18 PA7
No.
Input
float
Main
Function
(after reset)
Output
PP
Port / Control
Input
Output
OD
Level
Type
Pin
T
X
Port A6
X
T
Alternate Function
I2C Data
Port A5
Port A4
I2C Clock
In-situ programming selection (should be tied low in
standard user mode).
26 ISPSEL
I
27 VSS
S
Ground
28 VDD
S
Main power supply
Notes:
1. In the interrupt input column, “eiX” defines the associated external interrupt vector. If the weak pull-up column (wpu) is
merged with the interrupt column (int), then the I/O configuration is pull-up interrupt input, else the configuration is floating
interrupt input.
2. In the open drain output column, “T” defines a true open drain I/O (P-Buffer and protection diode to VDD are not implemented). See Section 9 "I/O PORTS" on page 30 and Section 13.8 "I/O PORT PIN CHARACTERISTICS" on page 116
for more details.
3. OSC1 and OSC2 pins connect a crystal or ceramic resonator, an external RC, or an external source to the on-chip
oscillator see Section 2 "PIN DESCRIPTION" on page 7 and Section 13.5 "CLOCK AND TIMING CHARACTERISTICS"
on page 104 for more details.
9/135
ST72104Gx-Auto, ST72215Gx-Auto, ST72216Gx-Auto, ST72254Gx-Auto
3 REGISTER AND MEMORY MAP
As shown in the Figure 3, the MCU is capable of
addressing 64 Kbytes of memories and I/O registers.
The available memory locations consist of 128
bytes of register location, 256 bytes of RAM and
up to 8Kbytes of user program memory. The RAM
space includes up to 128 bytes for the stack from
0100h to 017Fh.
The highest address bytes contain the user reset
and interrupt vectors.
IMPORTANT: Memory locations marked as “Reserved” must never be accessed. Accessing a reserved area can have unpredictable effects on the
device.
Figure 3. Memory Map
0000h
HW Registers
(see Table 2)
0080h
256 bytes RAM
00FFh
0100h
007Fh
0080h
017Fh
0180h
Reserved
017Fh
Short Addressing RAM
Zero page
(128 bytes)
Stack or
16-bit Addressing RAM
(128 bytes)
DFFFh
E000h
Program Memory
(4K, 8K bytes)
FFDFh
FFE0h
FFFFh
10/135
E000h
8 Kbytes
F000h
Interrupt & Reset Vectors
(see Table 5 on page 26)
4 Kbytes
FFFFh
ST72104Gx-Auto, ST72215Gx-Auto, ST72216Gx-Auto, ST72254Gx-Auto
Table 2. Hardware Register Map
Address
0000h
0001h
0002h
Block
Port C
Register
Label
PCDR
PCDDR
PCOR
0003h
0004h
0005h
0006h
Port B
PBDR
PBDDR
PBOR
Port A
00h 1)
00h
00h
R/W 2)
R/W 2)
R/W 2)
00h 1)
00h
00h
R/W
R/W
R/W
00h 1)
00h
00h
R/W
R/W
R/W
Port B Data Register
Port B Data Direction Register
Port B Option Register
PADR
PADDR
PAOR
Port A Data Register
Port A Data Direction Register
Port A Option Register
Reserved (21 bytes)
0020h
0021h
0022h
0023h
SPI
0024h
WATCHDOG
0025h
MISCR1
Miscellaneous Register 1
00h
R/W
SPIDR
SPICR
SPISR
SPI Data I/O Register
SPI Control Register
SPI Status Register
xxh
0xh
00h
R/W
R/W
Read Only
WDGCR
Watchdog Control Register
7Fh
R/W
CRSR
Clock, Reset, Supply Control / Status Register 000x 000x R/W
0026h
0027h
002Fh
to
0030h
Port C Data Register
Port C Data Direction Register
Port C Option Register
Remarks
Reserved (1 byte)
000Bh
to
001Fh
0028h
0029h
002Ah
002Bh
002Ch
002Dh
002Eh
Reset
Status
Reserved (1 byte)
0007h
0008h
0009h
000Ah
Register Name
Reserved (2 bytes)
I2C
I2CCR
I2CSR1
I2CSR2
I2CCCR
I2COAR1
I2COAR2
I2CDR
Control Register
Status Register 1
Status Register 2
Clock Control Register
Own Address Register 1
Own Address Register 2
Data Register
00h
00h
00h
00h
00h
00h
00h
R/W
Read Only
Read Only
R/W
R/W
R/W
R/W
Reserved (2 bytes)
11/135
ST72104Gx-Auto, ST72215Gx-Auto, ST72216Gx-Auto, ST72254Gx-Auto
Address
0031h
0032h
0033h
0034h
0035h
0036h
0037h
0038h
0039h
003Ah
003Bh
003Ch
003Dh
003Eh
003Fh
Block
Register
Label
Register Name
Reset
Status
Remarks
TACR2
TACR1
TASR
TAIC1HR
TAIC1LR
TAOC1HR
TAOC1LR
TACHR
TACLR
TAACHR
TAACLR
TAIC2HR
TAIC2LR
TAOC2HR
TAOC2LR
Timer A Control Register 2
Timer A Control Register 1
Timer A Status Register
Timer A Input Capture 1 High Register
Timer A Input Capture 1 Low Register
Timer A Output Compare 1 High Register
Timer A Output Compare 1 Low Register
Timer A Counter High Register
Timer A Counter Low Register
Timer A Alternate Counter High Register
Timer A Alternate Counter Low Register
Timer A Input Capture 2 High Register
Timer A Input Capture 2 Low Register
Timer A Output Compare 2 High Register
Timer A Output Compare 2 Low Register
00h
00h
xxh
xxh
xxh
80h
00h
FFh
FCh
FFh
FCh
xxh
xxh
80h
00h
R/W
R/W
Read Only
Read Only
Read Only
R/W
R/W
Read Only
Read Only
Read Only
Read Only
Read Only
Read Only
R/W
R/W
0040h
MISCR2
Miscellaneous Register 2
00h
R/W
0041h
0042h
0043h
0044h
0045h
0046h
0047h
0048h
0049h
004Ah
004Bh
004Ch
004Dh
004Eh
004Fh
TBCR2
TBCR1
TBSR
TBIC1HR
TBIC1LR
TBOC1HR
TBOC1LR
TBCHR
TBCLR
TBACHR
TBACLR
TBIC2HR
TBIC2LR
TBOC2HR
TBOC2LR
Timer B Control Register 2
Timer B Control Register 1
Timer B Status Register
Timer B Input Capture 1 High Register
Timer B Input Capture 1 Low Register
Timer B Output Compare 1 High Register
Timer B Output Compare 1 Low Register
Timer B Counter High Register
Timer B Counter Low Register
Timer B Alternate Counter High Register
Timer B Alternate Counter Low Register
Timer B Input Capture 2 High Register
Timer B Input Capture 2 Low Register
Timer B Output Compare 2 High Register
Timer B Output Compare 2 Low Register
00h
00h
xxh
xxh
xxh
80h
00h
FFh
FCh
FFh
FCh
xxh
xxh
80h
00h
R/W
R/W
Read Only
Read Only
Read Only
R/W
R/W
Read Only
Read Only
Read Only
Read Only
Read Only
Read Only
R/W
R/W
00h
00h
Read Only
R/W
TIMER A
TIMER B
0050h
to
006Fh
0070h
0071h
Reserved (32 bytes)
ADC
ADCDR
ADCCSR
0072h
to
007Fh
Data Register
Control/Status Register
Reserved (14 bytes)
Legend: x=undefined, R/W=read/write
Notes:
1. The contents of the I/O port DR registers are readable only in output configuration. In input configuration, the values
of the I/O pins are returned instead of the DR register contents.
2. The bits associated with unavailable pins must always keep their reset value.
12/135
ST72104Gx-Auto, ST72215Gx-Auto, ST72216Gx-Auto, ST72254Gx-Auto
4 FLASH PROGRAM MEMORY
■
■
■
■
Remote In-Situ Programming (ISP) mode
Up to 16 bytes programmed in the same cycle
MTP memory (Multiple Time Programmable)
Readout memory protection against piracy
4.3 STRUCTURAL ORGANIZATION
The Flash program memory is organized in a single 8-bit wide memory block which can be used for
storing both code and data constants.
The Flash program memory is mapped in the upper part of the ST7 addressing space and includes
the reset and interrupt user vector area.
4.4 IN-SITU PROGRAMMING (ISP) MODE
The Flash program memory can be programmed
using Remote ISP mode. This ISP mode allows
the contents of the ST7 program memory to be updated using a standard ST7 programming tools after the device is mounted on the application board.
This feature can be implemented with a minimum
number of added components and board area impact.
An example Remote ISP hardware interface to the
standard ST7 programming tool is described below. For more details on ISP programming, refer to
the ST7 Programming Specification.
Remote ISP Overview
The Remote ISP mode is initiated by a specific sequence on the dedicated ISPSEL pin.
The Remote ISP is performed in three steps:
– Selection of the RAM execution mode
– Download of Remote ISP code in RAM
– Execution of Remote ISP code in RAM to program the user program into the Flash
Remote ISP hardware configuration
In Remote ISP mode, the ST7 has to be supplied
with power (VDD and VSS) and a clock signal (oscillator and application crystal circuit for example).
HE10 CONNECTOR TYPE
TO PROGRAMMING TOOL
XTAL
1
CL1
CL0
VDD
4.2 MAIN FEATURES
OSC1
Flash devices have a single voltage non-volatile
Flash memory that may be programmed in-situ (or
plugged in a programming tool) on a byte-by-byte
basis.
This mode needs five signals (plus the VDD signal
if necessary) to be connected to the programming
tool. This signals are:
– RESET: device reset
– VSS: device ground power supply
– ISPCLK: ISP output serial clock pin
– ISPDATA: ISP input serial data pin
– ISPSEL: Remote ISP mode selection. This pin
must be connected to VSS on the application
board through a pull-down resistor.
If any of these pins are used for other purposes on
the application, a serial resistor has to be implemented to avoid a conflict if the other device forces
the signal level.
Figure 4 shows a typical hardware interface to a
standard ST7 programming tool. For more details
on the pin locations, refer to the device pinout description.
Figure 4. Typical Remote ISP Interface
OSC2
4.1 INTRODUCTION
ISPSEL
10KΩ
VSS
RESET
ST7
ISPCLK
ISPDATA
47KΩ
APPLICATION
4.5 MEMORY READOUT PROTECTION
The readout protection is enabled through an option bit.
For Flash devices, when this option is selected,
the program and data stored in the Flash memory
are protected against readout piracy (including a
re-write protection). When this protection option is
removed the entire Flash program memory is first
automatically erased. However, the E2PROM data
memory (when available) can be protected only
with ROM devices.
13/135
ST72104Gx-Auto, ST72215Gx-Auto, ST72216Gx-Auto, ST72254Gx-Auto
5 CENTRAL PROCESSING UNIT
5.1 INTRODUCTION
This CPU has a full 8-bit architecture and contains
six internal registers allowing efficient 8-bit data
manipulation.
5.2 MAIN FEATURES
■
■
■
■
■
■
■
■
63 basic instructions
Fast 8-bit by 8-bit multiply
17 main addressing modes
Two 8-bit index registers
16-bit stack pointer
Low power modes
Maskable hardware interrupts
Non-maskable software interrupt
5.3 CPU REGISTERS
The six CPU registers shown in Figure 5 are not
present in the memory mapping and are accessed
by specific instructions.
Accumulator (A)
The Accumulator is an 8-bit general purpose register used to hold operands and the results of the
arithmetic and logic calculations and to manipulate
data.
Index Registers (X and Y)
In indexed addressing modes, these 8-bit registers
are used to create either effective addresses or
temporary storage areas for data manipulation.
(The Cross-Assembler generates a precede instruction (PRE) to indicate that the following instruction refers to the Y register.)
The Y register is not affected by the interrupt automatic procedures (not pushed to and popped from
the stack).
Program Counter (PC)
The program counter is a 16-bit register containing
the address of the next instruction to be executed
by the CPU. It is made of two 8-bit registers PCL
(Program Counter Low which is the LSB) and PCH
(Program Counter High which is the MSB).
Figure 5. CPU Registers
7
0
ACCUMULATOR
RESET VALUE = XXh
7
0
X INDEX REGISTER
RESET VALUE = XXh
7
0
Y INDEX REGISTER
RESET VALUE = XXh
15
PCH
8 7
PCL
0
PROGRAM COUNTER
RESET VALUE = RESET VECTOR @ FFFEh-FFFFh
7
1 1 1 H I
0
N Z C
CONDITION CODE REGISTER
RESET VALUE = 1 1 1 X 1 X X X
15
8 7
0
STACK POINTER
RESET VALUE = STACK HIGHER ADDRESS
X = Undefined Value
14/135
ST72104Gx-Auto, ST72215Gx-Auto, ST72216Gx-Auto, ST72254Gx-Auto
CPU REGISTERS (cont’d)
CONDITION CODE REGISTER (CC)
Read/Write
Reset Value: 111x1xxx
7
1
0
1
1
H
I
N
Z
because the I bit is set by hardware at the start of
the routine and reset by the IRET instruction at the
end of the routine. If the I bit is cleared by software
in the interrupt routine, pending interrupts are
serviced regardless of the priority level of the current interrupt routine.
C
The 8-bit Condition Code register contains the interrupt mask and four flags representative of the
result of the instruction just executed. This register
can also be handled by the PUSH and POP instructions.
These bits can be individually tested and/or controlled by specific instructions.
Bit 4 = H Half carry
This bit is set by hardware when a carry occurs between bits 3 and 4 of the ALU during an ADD or
ADC instruction. It is reset by hardware during the
same instructions.
0: No half carry has occurred.
1: A half carry has occurred.
This bit is tested using the JRH or JRNH instruction. The H bit is useful in BCD arithmetic subroutines.
Bit 2 = N Negative
This bit is set and cleared by hardware. It is representative of the result sign of the last arithmetic,
logical or data manipulation. It is a copy of the 7th
bit of the result.
0: The result of the last operation is positive or null.
1: The result of the last operation is negative
(that is, the most significant bit is a logic 1).
This bit is accessed by the JRMI and JRPL instructions.
Bit 1 = Z Zero
This bit is set and cleared by hardware. This bit indicates that the result of the last arithmetic, logical
or data manipulation is zero.
0: The result of the last operation is different from
zero.
1: The result of the last operation is zero.
This bit is accessed by the JREQ and JRNE test
instructions.
Bit 3 = I Interrupt mask
This bit is set by hardware when entering in interrupt or by software to disable all interrupts except
the TRAP software interrupt. This bit is cleared by
software.
0: Interrupts are enabled.
1: Interrupts are disabled.
This bit is controlled by the RIM, SIM and IRET instructions and is tested by the JRM and JRNM instructions.
Note: Interrupts requested while I is set are
latched and can be processed when I is cleared.
By default an interrupt routine is not interruptible
Bit 0 = C Carry/borrow
This bit is set and cleared by hardware and software. It indicates an overflow or an underflow has
occurred during the last arithmetic operation.
0: No overflow or underflow has occurred.
1: An overflow or underflow has occurred.
This bit is driven by the SCF and RCF instructions
and tested by the JRC and JRNC instructions. It is
also affected by the “bit test and branch”, shift and
rotate instructions.
15/135
ST72104Gx-Auto, ST72215Gx-Auto, ST72216Gx-Auto, ST72254Gx-Auto
CPU REGISTERS (cont’d)
Stack Pointer (SP)
Read/Write
Reset Value: 01 7Fh
15
0
8
0
0
0
0
0
0
7
0
1
0
SP6
SP5
SP4
SP3
SP2
SP1
SP0
The Stack Pointer is a 16-bit register which is always pointing to the next free location in the stack.
It is then decremented after data has been pushed
onto the stack and incremented before data is
popped from the stack (see Figure 6).
Since the stack is 128 bytes deep, the 9 most significant bits are forced by hardware. Following an
MCU Reset, or after a Reset Stack Pointer instruction (RSP), the Stack Pointer contains its reset value (the SP6 to SP0 bits are set) which is the stack
higher address.
The least significant byte of the Stack Pointer
(called S) can be directly accessed by a LD instruction.
Note: When the lower limit is exceeded, the Stack
Pointer wraps around to the stack upper limit, without indicating the stack overflow. The previously
stored information is then overwritten and therefore lost. The stack also wraps in case of an underflow.
The stack is used to save the return address during a subroutine call and the CPU context during
an interrupt. The user may also directly manipulate
the stack by means of the PUSH and POP instructions. In the case of an interrupt, the PCL is stored
at the first location pointed to by the SP. Then the
other registers are stored in the next locations as
shown in Figure 6.
– When an interrupt is received, the SP is decremented and the context is pushed on the stack.
– On return from interrupt, the SP is incremented
and the context is popped from the stack.
A subroutine call occupies two locations and an interrupt five locations in the stack area.
Figure 6. Stack Manipulation Example
CALL
Subroutine
PUSH Y
Interrupt
Event
POP Y
RET
or RSP
IRET
@ 0100h
SP
SP
CC
A
X
X
X
PCH
PCH
PCH
PCL
PCL
PCL
PCH
PCH
PCH
PCH
PCH
PCL
PCL
PCL
PCL
PCL
SP
@ 017Fh
Stack Higher Address = 017Fh
Stack Lower Address = 0100h
16/135
SP
Y
CC
A
CC
A
SP
SP
ST72104Gx-Auto, ST72215Gx-Auto, ST72216Gx-Auto, ST72254Gx-Auto
6 SUPPLY, RESET AND CLOCK MANAGEMENT
The
ST72104G-Auto,
ST72215G-Auto,
ST72216G-Auto and ST72254G-Auto microcontrollers include a range of utility features for securing the application in critical situations (for example, in case of a power brown-out), and reducing
the number of external components. An overview
is shown in Figure 7.
See Section 13 "ELECTRICAL CHARACTERISTICS" on page 95 for more details.
Main Features
■ Supply Manager with main supply low voltage
detection (LVD)
■ Reset Sequence Manager (RSM)
■ Multi-Oscillator (MO)
– 4 Crystal/Ceramic resonator oscillators
– 1 External RC oscillator
– 1 Internal RC oscillator
■ Clock Security System (CSS)
– Clock Filter
– Backup Safe Oscillator
Figure 7. Clock, Reset and Supply Block Diagram
MCO
CLOCK SECURITY SYSTEM
(CSS)
OSC2
OSC1
RESET
VDD
VSS
MULTIOSCILLATOR
(MO)
CLOCK
SAFE
FILTER
OSC
RESET SEQUENCE
MANAGER
(RSM)
LOW VOLTAGE
DETECTOR
(LVD)
MAIN CLOCK
CONTROLLER
(MCC)
fOSC
fCPU
FROM
WATCHDOG
PERIPHERAL
LVD
CRSR
0
0
0
RF
CSS
0
IE
D
WDG
RF
CSS INTERRUPT
17/135
ST72104Gx-Auto, ST72215Gx-Auto, ST72216Gx-Auto, ST72254Gx-Auto
6.1 LOW VOLTAGE DETECTOR (LVD)
To allow the integration of power management
features in the application, the Low Voltage Detector function (LVD) generates a static reset when
the VDD supply voltage is below a VIT- reference
value. This means that it secures the power-up as
well as the power-down keeping the ST7 in reset.
The VIT- reference value for a voltage drop is lower
than the VIT+ reference value for power-on in order
to avoid a parasitic reset when the MCU starts running and sinks current on the supply (hysteresis).
The LVD Reset circuitry generates a reset when
VDD is below:
– VIT+ when VDD is rising
– VIT- when VDD is falling
The LVD function is illustrated in the Figure 8.
Provided the minimum VDD value (guaranteed for
the oscillator frequency) is above VIT-, the MCU
can only be in two modes:
– under full software control
– in static safe reset
In these conditions, secure operation is always ensured for the application without the need for external reset hardware.
During a Low Voltage Detector Reset, the RESET
pin is held low, thus permitting the MCU to reset
other devices.
Notes:
1. The LVD allows the device to be used without
any external RESET circuitry.
2. Three different reference levels are selectable
through the option byte according to the application requirement.
LVD application note
Application software can detect a reset caused by
the LVD by reading the LVDRF bit in the CRSR
register.
This bit is set by hardware when a LVD reset is
generated and cleared by software (writing zero).
Figure 8. Low Voltage Detector vs Reset
VDD
Vhyst
VIT+
VIT-
RESET
18/135
ST72104Gx-Auto, ST72215Gx-Auto, ST72216Gx-Auto, ST72254Gx-Auto
6.2 RESET SEQUENCE MANAGER (RSM)
6.2.1 Introduction
The reset sequence manager includes three RESET sources as shown in Figure 10:
■ External RESET source pulse
■ Internal LVD RESET (Low Voltage Detection)
■ Internal WATCHDOG RESET
These sources act on the RESET pin and it is always kept low during the delay phase.
The RESET service routine vector is fixed at addresses FFFEh-FFFFh in the ST7 memory map.
The basic RESET sequence consists of three
phases as shown in Figure 9:
■ Delay depending on the RESET source
■ 4096 CPU clock cycle delay
■ RESET vector fetch
The 4096 CPU clock cycle delay allows the oscillator to stabilise and ensures that recovery has
taken place from the Reset state.
The RESET vector fetch phase duration is 2 clock
cycles.
Figure 9. RESET Sequence Phases
RESET
DELAY
INTERNAL RESET
FETCH
4096 CLOCK CYCLES VECTOR
Figure 10. Reset Block Diagram
VDD
INTERNAL
RESET
RON
COUNTER
fCPU
RESET
WATCHDOG RESET
LVD RESET
19/135
ST72104Gx-Auto, ST72215Gx-Auto, ST72216Gx-Auto, ST72254Gx-Auto
RESET SEQUENCE MANAGER (Cont’d)
6.2.2 Asynchronous External RESET pin
The RESET pin is both an input and an open-drain
output with integrated RON weak pull-up resistor.
This pull-up has no fixed value but varies in accordance with the input voltage. It can be pulled
low by external circuitry to reset the device. See
electrical characteristics section for more details.
A RESET signal originating from an external
source must have a duration of at least th(RSTL)in in
order to be recognized. This detection is asynchronous and therefore the MCU can enter reset state
even in HALT mode.
The RESET pin is an asynchronous signal which
plays a major role in EMS performance. In a noisy
environment, it is recommended to follow the
guidelines mentioned in the electrical characteristics section.
Two RESET sequences can be associated with
this RESET source: short or long external reset
pulse (see Figure 11).
Starting from the external RESET pulse recognition, the device RESET pin acts as an output that
is pulled low during at least tw(RSTL)out.
6.2.3 Internal Low Voltage Detection RESET
Two different RESET sequences caused by the internal LVD circuitry can be distinguished:
■ Power-On RESET
■ Voltage Drop RESET
The device RESET pin acts as an output that is
pulled low when VDD<VIT+ (rising edge) or
VDD<VIT- (falling edge) as shown in Figure 11.
The LVD filters spikes on VDD larger than tg(VDD) to
avoid parasitic resets.
6.2.4 Internal Watchdog RESET
The RESET sequence generated by a internal
Watchdog counter overflow is shown in Figure 11.
Starting from the Watchdog counter underflow, the
device RESET pin acts as an output that is pulled
low during at least tw(RSTL)out.
Figure 11. RESET Sequences
VDD
VIT+
VIT-
LVD
RESET
RUN
SHORT EXT.
RESET
RUN
DELAY
LONG EXT.
RESET
RUN
DELAY
WATCHDOG
RESET
RUN
DELAY
RUN
DELAY
tw(RSTL)out
th(RSTL)in
tw(RSTL)out
th(RSTL)in
EXTERNAL
RESET
SOURCE
RESET PIN
WATCHDOG
RESET
WATCHDOG UNDERFLOW
INTERNAL RESET (4096 TCPU)
FETCH VECTOR
20/135
ST72104Gx-Auto, ST72215Gx-Auto, ST72216Gx-Auto, ST72254Gx-Auto
6.3 MULTI-OSCILLATOR (MO)
External RC Oscillator
This oscillator allows a low cost solution for the
main clock of the ST7 using only an external resistor and an external capacitor. The frequency of the
external RC oscillator (in the range of some MHz)
is fixed by the resistor and the capacitor values.
Consequently in this MO mode, the accuracy of
the clock is dependent on VDD, TA, process variations and the accuracy of the discrete components
used. This option should not be used in applications that require accurate timing.
Internal RC Oscillator
The internal RC oscillator mode is based on the
same principle as the external RC oscillator including the resistance and the capacitance of the device. This mode is the most cost effective one with
the drawback of a lower frequency accuracy. Its
frequency is in the range of several MHz. This op-
Table 3. ST7 Clock Sources
Crystal/Ceramic Resonators
External Clock
Hardware Configuration
External RC Oscillator
External Clock Source
In this external clock mode, a clock signal (square,
sinus or triangle) with ~50% duty cycle has to drive
the OSC1 pin while the OSC2 pin is tied to ground.
Crystal/Ceramic Oscillators
This family of oscillators has the advantage of producing a very accurate rate on the main clock of
the ST7. The selection within a list of four oscillators with different frequency ranges has to be done
by option byte in order to reduce consumption. In
this mode of the multi-oscillator, the resonator and
the load capacitors have to be placed as close as
possible to the oscillator pins in order to minimize
output distortion and start-up stabilization time.
The loading capacitance values must be adjusted
according to the selected oscillator.
These oscillators are not stopped during the RESET phase to avoid losing time in the oscillator
start-up phase.
tion should not be used in applications that require
accurate timing.
In this mode, the two oscillator pins have to be tied
to ground.
Internal RC Oscillator
The main clock of the ST7 can be generated by
four different source types coming from the multioscillator block:
■ an external source
■ 4 crystal or ceramic resonator oscillators
■ an external RC oscillator
■ an internal high frequency RC oscillator
Each oscillator is optimized for a given frequency
range in terms of consumption and is selectable
through the option byte. The associated hardware
configuration are shown in Table 3. Refer to the
electrical characteristics section for more details.
ST7
OSC1
OSC2
EXTERNAL
SOURCE
ST7
OSC1
CL1
OSC2
LOAD
CAPACITORS
CL2
ST7
OSC1
OSC2
REX
CEX
ST7
OSC1
OSC2
21/135
ST72104Gx-Auto, ST72215Gx-Auto, ST72216Gx-Auto, ST72254Gx-Auto
6.4 CLOCK SECURITY SYSTEM (CSS)
The Clock Security System (CSS) protects the
ST7 against main clock problems. To allow the integration of the security features in the applications, it is based on a clock filter control and an Internal safe oscillator. The CSS can be enabled or
disabled by option byte.
6.4.1 Clock Filter Control
The clock filter is based on a clock frequency limitation function.
This filter function is able to detect and filter high
frequency spikes on the ST7 main clock.
If the oscillator is not working properly (e.g. working at a harmonic frequency of the resonator), the
current active oscillator clock can be totally filtered, and then no clock signal is available for the
ST7 from this oscillator anymore. If the original
clock source recovers, the filtering is stopped automatically and the oscillator supplies the ST7
clock.
6.4.2 Safe Oscillator Control
The safe oscillator of the CSS block is a low frequency back-up clock source (see Figure 12).
If the clock signal disappears (due to a broken or
disconnected resonator...) during a safe oscillator
period, the safe oscillator delivers a low frequency
clock signal which allows the ST7 to perform some
rescue operations.
Automatically, the ST7 clock source switches back
from the safe oscillator if the original clock source
recovers.
Limitation detection
The automatic safe oscillator selection is notified
by hardware setting the CSSD bit of the CRSR
register. An interrupt can be generated if the CSSIE bit has been previously set.
These two bits are described in the CRSR register
description.
6.4.3 Low Power Modes
Mode
WAIT
HALT
Description
No effect on CSS. CSS interrupt cause the
device to exit from Wait mode.
The CRSR register is frozen. The CSS (including the safe oscillator) is disabled until
HALT mode is exited. The previous CSS
configuration resumes when the MCU is
woken up by an interrupt with “exit from
HALT mode” capability or from the counter
reset value when the MCU is woken up by a
RESET.
6.4.4 Interrupts
The CSS interrupt event generates an interrupt if
the corresponding Enable Control Bit (CSSIE) is
set and the interrupt mask in the CC register is reset (RIM instruction).
Interrupt Event
Enable
Event
Control
Flag
Bit
CSS event detection
(safe oscillator acti- CSSD
vated as main clock)
CSSIE
Exit
from
Wait
Exit
from
Halt1)
Yes
No
Notes:
1. This interrupt allows to exit from Active Halt mode if this
mode is available in the MCU.
SAFE OSCILLATOR
FUNCTION
CLOCK FILTER
FUNCTION
Figure 12. Clock Filter Function and Safe Oscillator Function
22/135
fOSC/2
fCPU
fOSC/2
fSFOSC
fCPU
ST72104Gx-Auto, ST72215Gx-Auto, ST72216Gx-Auto, ST72254Gx-Auto
6.5 CLOCK RESET AND SUPPLY REGISTER DESCRIPTION (CRSR)
Read / Write
Reset Value: 000x 000x (XXh)
7
0
0
0
0
LVD
RF
CSS
IE
0
CSS WDG
D
RF
Bit 7:5 = Reserved, always read as 0.
Bit 4 = LVDRF LVD reset flag
This bit indicates that the last RESET was generated by the LVD block. It is set by hardware (LVD
reset) and cleared by software (writing zero). See
WDGRF flag description for more details. When
the LVD is disabled by option byte, the LVDRF bit
value is undefined.
Bit 3 = Reserved, always read as 0.
Bit 2 = CSSIE Clock security syst interrupt enable
This bit enables the interrupt when a disturbance
is detected by the clock security system (CSSD bit
set). It is set and cleared by software.
0: Clock security system interrupt disabled
1: Clock security system interrupt enabled
Refer to Table 5, “Interrupt Mapping,” on page 26
for more details on the CSS interrupt vector. When
the CSS is disabled by option byte, the CSSIE bit
has no effect.
.
Bit 1 = CSSD Clock security system detection
This bit indicates that the safe oscillator of the
clock security system block has been selected by
hardware due to a disturbance on the main clock
signal (fOSC). It is set by hardware and cleared by
reading the CRSR register when the original oscillator recovers.
0: Safe oscillator is not active
1: Safe oscillator has been activated
When the CSS is disabled by option byte, the
CSSD bit value is forced to 0.
Bit 0 = WDGRF Watchdog reset flag
This bit indicates that the last RESET was generated by the watchdog peripheral. It is set by hardware (Watchdog RESET) and cleared by software
(writing zero) or an LVD RESET (to ensure a stable cleared state of the WDGRF flag when the
CPU starts).
Combined with the LVDRF flag information, the
flag description is given by the following table.
RESET Sources
External RESET pin
Watchdog
LVD
LVDRF
0
0
1
WDGRF
0
1
X
Application notes
The LVDRF flag is not cleared when another RESET type occurs (external or watchdog), the
LVDRF flag remains set to keep trace of the original failure.
In this case, a watchdog reset can be detected by
software while an external reset cannot.
Table 4. Clock, Reset and Supply Register Map and Reset Values
Address
(Hex.)
Register
Label
0025h
CRSR
Reset Value
7
6
5
4
3
2
1
0
0
0
0
LVDRF
x
0
CSSIE
0
CSSD
0
WDGRF
x
23/135
ST72104Gx-Auto, ST72215Gx-Auto, ST72216Gx-Auto, ST72254Gx-Auto
6.6 MAIN CLOCK CONTROLLER (MCC)
The Main Clock Controller (MCC) supplies the
clock for the ST7 CPU and its internal peripherals.
It allows SLOW power saving mode to be managed by the application.
All functions are managed by the Miscellaneous
register 1 (MISCR1).
The MCC block consists of:
■ A programmable CPU clock prescaler
■ A clock-out signal to supply external devices
The prescaler allows the selection of the main
clock frequency and is controlled by three bits of
the MISCR1: CP1, CP0 and SMS.
The clock-out capability consists of a dedicated
I/O port pin configurable as an fCPU clock output to
drive external devices. It is controlled by the MCO
bit in the MISCR1 register.
See Section 10 "MISCELLANEOUS REGISTERS" on page 36 for more details.
Figure 13. Main Clock Controller (MCC) Block Diagram
CLOCK TO CAN
PERIPHERAL
PORT
ALTERNATE
FUNCTION
MCO
fOSC/2
MISCR1
-
fOSC
DIV 2
-
MCO
-
-
CP1 CP0 SMS
DIV 2, 4, 8, 16
fCPU
24/135
CPU CLOCK
TO CPU AND
PERIPHERALS
ST72104Gx-Auto, ST72215Gx-Auto, ST72216Gx-Auto, ST72254Gx-Auto
7 INTERRUPTS
The ST7 core may be interrupted by one of two different methods: maskable hardware interrupts as
listed in the Interrupt Mapping Table and a nonmaskable software interrupt (TRAP). The Interrupt
processing flowchart is shown in Figure 14.
The maskable interrupts must be enabled by
clearing the I bit in order to be serviced. However,
disabled interrupts may be latched and processed
when they are enabled (see external interrupts
subsection).
Note: After reset, all interrupts are disabled.
When an interrupt has to be serviced:
– Normal processing is suspended at the end of
the current instruction execution.
– The PC, X, A and CC registers are saved onto
the stack.
– The I bit of the CC register is set to prevent additional interrupts.
– The PC is then loaded with the interrupt vector of
the interrupt to service and the first instruction of
the interrupt service routine is fetched (refer to
the Interrupt Mapping Table for vector addresses).
The interrupt service routine should finish with the
IRET instruction which causes the contents of the
saved registers to be recovered from the stack.
Note: As a consequence of the IRET instruction,
the I bit will be cleared and the main program will
resume.
Priority Management
By default, a servicing interrupt cannot be interrupted because the I bit is set by hardware entering in interrupt routine.
In the case when several interrupts are simultaneously pending, an hardware priority defines which
one will be serviced first (see the Interrupt Mapping Table).
Interrupts and Low Power Mode
All interrupts allow the processor to leave the
WAIT low power mode. Only external and specifically mentioned interrupts allow the processor to
leave the HALT low power mode (refer to the “Exit
from HALT” column in the Interrupt Mapping Table).
7.1 NON-MASKABLE SOFTWARE INTERRUPT
It will be serviced according to the flowchart on
Figure 14.
7.2 EXTERNAL INTERRUPTS
External interrupt vectors can be loaded into the
PC register if the corresponding external interrupt
occurred and if the I bit is cleared. These interrupts
allow the processor to leave the Halt low power
mode.
The external interrupt polarity is selected through
the miscellaneous register or interrupt register (if
available).
An external interrupt triggered on edge will be
latched and the interrupt request automatically
cleared upon entering the interrupt service routine.
If several input pins, connected to the same interrupt vector, are configured as interrupts, their signals are logically NANDed before entering the
edge/level detection block.
Caution: The type of sensitivity defined in the Miscellaneous or Interrupt register (if available) applies to the ei source. In case of a NANDed source
(as described on the I/O ports section), a low level
on an I/O pin configured as input with interrupt,
masks the interrupt request even in case of risingedge sensitivity.
7.3 PERIPHERAL INTERRUPTS
Different peripheral interrupt flags in the status
register are able to cause an interrupt when they
are active if both:
– The I bit of the CC register is cleared.
– The corresponding enable bit is set in the control
register.
If any of these two conditions is false, the interrupt
is latched and thus remains pending.
Clearing an interrupt request is done by:
– Writing “0” to the corresponding bit in the status
register or
– Access to the status register while the flag is set
followed by a read or write of an associated register.
Note: The clearing sequence resets the internal
latch. A pending interrupt (that is, waiting to be enabled) will therefore be lost if the clear sequence is
executed.
This interrupt is entered when the TRAP instruction is executed regardless of the state of the I bit.
25/135
ST72104Gx-Auto, ST72215Gx-Auto, ST72216Gx-Auto, ST72254Gx-Auto
INTERRUPTS (Cont’d)
Figure 14. Interrupt Processing Flowchart
FROM RESET
I BIT SET?
N
N
Y
Y
FETCH NEXT INSTRUCTION
N
IRET?
INTERRUPT
PENDING?
STACK PC, X, A, CC
SET I BIT
LOAD PC FROM INTERRUPT VECTOR
Y
EXECUTE INSTRUCTION
RESTORE PC, X, A, CC FROM STACK
THIS CLEARS I BIT BY DEFAULT
Table 5. Interrupt Mapping
No.
Source
Block
RESET
TRAP
Description
Register
Label
Reset
Software Interrupt
Highest
Priority
N/A
0
ei0
External Interrupt Port A7..0 (C5..01)
1
ei1
External Interrupt Port B7..0 (C5..01)
2
CSS
Clock Security System Interrupt
CRSR
3
SPI
SPI Peripheral Interrupts
SPISR
4
TIMER A
TIMER A Peripheral Interrupts
TASR
5
6
Priority
Order
Exit
from
HALT
yes
FFFEh-FFFFh
no
FFFCh-FFFDh
yes
TIMER B Peripheral Interrupts
FFFAh-FFFBh
FFF8h-FFF9h
FFF6h-FFF7h
no
FFF4h-FFF5h
FFF2h-FFF3h
Not used
TIMER B
Address
Vector
FFF0h-FFF1h
TBSR
no
FFEEh-FFEFh
7
Not used
FFECh-FFEDh
8
Not used
FFEAh-FFEBh
9
Not used
FFE8h-FFE9h
10
Not used
11
I²C
I²C Peripheral Interrupt
12
Not Used
13
Not Used
Notes:
1. Configurable by option byte.
26/135
FFE6h-FFE7h
I2CSRx
no
Lowest
Priority
FFE4h-FFE5h
FFE2h-FFE3h
FFE0h-FFE1h
ST72104Gx-Auto, ST72215Gx-Auto, ST72216Gx-Auto, ST72254Gx-Auto
8 POWER SAVING MODES
8.1 INTRODUCTION
8.2 SLOW MODE
To give a large measure of flexibility to the application in terms of power consumption, three main
power saving modes are implemented in the ST7
(see Figure 15).
After a RESET the normal operating mode is selected by default (RUN mode). This mode drives
the device (CPU and embedded peripherals) by
means of a master clock which is based on the
main oscillator frequency divided by 2 (fCPU).
From Run mode, the different power saving
modes may be selected by setting the relevant
register bits or by calling the specific ST7 software
instruction whose action depends on the oscillator
status.
This mode has two targets:
– To reduce power consumption by decreasing the
internal clock in the device,
– To adapt the internal clock frequency (fCPU) to
the available supply voltage.
SLOW mode is controlled by three bits in the
MISCR1 register: the SMS bit which enables or
disables Slow mode and two CPx bits which select
the internal slow frequency (fCPU).
In this mode, the oscillator frequency can be divided by 4, 8, 16 or 32 instead of 2 in normal operating mode. The CPU and peripherals are clocked at
this lower frequency.
Note: SLOW-WAIT mode is activated when entering WAIT mode while the device is already in
SLOW mode.
Figure 15. Power Saving Mode Transitions
High
Figure 16. SLOW Mode Clock Transitions
RUN
fOSC/4
fOSC/8
fOSC/2
fCPU
SLOW
fOSC/2
MISCR1
WAIT
SLOW WAIT
CP1:0
00
01
SMS
HALT
Low
POWER CONSUMPTION
NEW SLOW
FREQUENCY
REQUEST
NORMAL RUN MODE
REQUEST
27/135
ST72104Gx-Auto, ST72215Gx-Auto, ST72216Gx-Auto, ST72254Gx-Auto
POWER SAVING MODES (Cont’d)
8.3 WAIT MODE
WAIT mode places the MCU in a low power consumption mode by stopping the CPU.
This power saving mode is selected by calling the
“WFI” ST7 software instruction.
All peripherals remain active. During WAIT mode,
the I bit of the CC register is forced to 0, to enable
all interrupts. All other registers and memory remain unchanged. The MCU remains in WAIT
mode until an interrupt or Reset occurs, whereupon the Program Counter branches to the starting
address of the interrupt or Reset service routine.
The MCU will remain in WAIT mode until a Reset
or an Interrupt occurs, causing it to wake up.
Refer to Figure 17.
Figure 17. WAIT Mode Flowchart
WFI INSTRUCTION
OSCILLATOR
PERIPHERALS
CPU
I BIT
ON
ON
OFF
0
N
RESET
Y
N
INTERRUPT
Y
OSCILLATOR
PERIPHERALS
CPU
I BIT
ON
OFF
ON
1
4096 CPU CLOCK CYCLE
DELAY
OSCILLATOR
PERIPHERALS
CPU
I BIT
ON
ON
ON
X 1)
FETCH RESET VECTOR
OR SERVICE INTERRUPT
Notes:
1. Before servicing an interrupt, the CC register is pushed
on the stack. The I bit of the CC register is set during the
interrupt routine and cleared when the CC register is
popped.
28/135
ST72104Gx-Auto, ST72215Gx-Auto, ST72216Gx-Auto, ST72254Gx-Auto
POWER SAVING MODES (Cont’d)
8.4 HALT MODE
Figure 19. HALT Mode Flow-chart
The HALT mode is the lowest power consumption
mode of the MCU. It is entered by executing the
ST7 HALT instruction (see Figure 19).
The MCU can exit HALT mode on reception of either a specific interrupt (see Table 5, “Interrupt
Mapping,” on page 26) or a RESET. When exiting
HALT mode by means of a RESET or an interrupt,
the oscillator is immediately turned on and the
4096 CPU cycle delay is used to stabilize the oscillator. After the start up delay, the CPU resumes
operation by servicing the interrupt or by fetching
the reset vector which woke it up (see Figure 18).
When entering HALT mode, the I bit in the CC register is forced to 0 to enable interrupts. Therefore,
if an interrupt is pending, the MCU wakes immediately.
In the HALT mode the main oscillator is turned off
causing all internal processing to be stopped, including the operation of the on-chip peripherals.
All peripherals are not clocked except the ones
which get their clock supply from another clock
generator (such as an external or auxiliary oscillator).
The compatibility of Watchdog operation with
HALT mode is configured by the “WDGHALT” option bit of the option byte. The HALT instruction
when executed while the Watchdog system is enabled, can generate a Watchdog RESET (see
Section 15.1 "OPTION BYTES" on page 129 for
more details).
Figure 18. HALT Mode Timing Overview
RUN
HALT
4096 CPU CYCLE
DELAY
RUN
HALT
INSTRUCTION
RESET
OR
INTERRUPT
FETCH
VECTOR
HALT INSTRUCTION
ENABLE
WDGHALT 1)
WATCHDOG
0
DISABLE
1
WATCHDOG
RESET
OSCILLATOR
OFF
PERIPHERALS 2) OFF
CPU
OFF
I BIT
0
N
RESET
N
Y
INTERRUPT 3)
Y
OSCILLATOR
PERIPHERALS
CPU
I BIT
ON
OFF
ON
1
4096 CPU CLOCK CYCLE
DELAY
OSCILLATOR
PERIPHERALS
CPU
I BIT
ON
ON
ON
X 4)
FETCH RESET VECTOR
OR SERVICE INTERRUPT
Notes:
1. WDGHALT is an option bit. See option byte section for
more details.
2. Peripheral clocked with an external clock source can
still be active.
3. Only some specific interrupts can exit the MCU from
HALT mode (such as external interrupt). Refer to Table 5,
“Interrupt Mapping,” on page 26 for more details.
4. Before servicing an interrupt, the CC register is pushed
on the stack. The I bit of the CC register is set during the
interrupt routine and cleared when the CC register is
popped.
29/135
ST72104Gx-Auto, ST72215Gx-Auto, ST72216Gx-Auto, ST72254Gx-Auto
9 I/O PORTS
9.1 INTRODUCTION
The I/O ports offer different functional modes:
– transfer of data through digital inputs and outputs
and for specific pins:
– external interrupt generation
– alternate signal input/output for the on-chip peripherals.
An I/O port contains up to 8 pins. Each pin can be
programmed independently as digital input (with or
without interrupt generation) or digital output.
9.2 FUNCTIONAL DESCRIPTION
Each port has two main registers:
– Data Register (DR)
– Data Direction Register (DDR)
and one optional register:
– Option Register (OR)
Each I/O pin may be programmed using the corresponding register bits in the DDR and OR registers: bit X corresponding to pin X of the port. The
same correspondence is used for the DR register.
The following description takes into account the
OR register, (for specific ports which do not provide this register refer to the I/O Port Implementation section). The generic I/O block diagram is
shown in Figure 20.
9.2.1 Input Modes
The input configuration is selected by clearing the
corresponding DDR register bit.
In this case, reading the DR register returns the
digital value applied to the external I/O pin.
Different input modes can be selected by software
through the OR register.
Notes:
1. Writing the DR register modifies the latch value
but does not affect the pin status.
2. When switching from input to output mode, the
DR register has to be written first to drive the correct level on the pin as soon as the port is configured as an output.
3. Do not use read/modify/write instructions (BSET
or BRES) to modify the DR register.
External interrupt function
When an I/O is configured as Input with Interrupt,
an event on this I/O can generate an external interrupt request to the CPU.
Each pin can independently generate an interrupt
request. The interrupt sensitivity is independently
30/135
programmable using the sensitivity bits in the Miscellaneous register.
Each external interrupt vector is linked to a dedicated group of I/O port pins (see pinout description
and interrupt section). If several input pins are selected simultaneously as interrupt source, these
are logically NANDed. For this reason if one of the
interrupt pins is tied low, it masks the other ones.
In case of a floating input with interrupt configuration, special care must be taken when changing
the configuration (see Figure 21).
The external interrupts are hardware interrupts,
which means that the request latch (not accessible
directly by the application) is automatically cleared
when the corresponding interrupt vector is
fetched. To clear an unwanted pending interrupt
by software, the sensitivity bits in the Miscellaneous register must be modified.
9.2.2 Output Modes
The output configuration is selected by setting the
corresponding DDR register bit. In this case, writing the DR register applies this digital value to the
I/O pin through the latch. Then reading the DR register returns the previously stored value.
Two different output modes can be selected by
software through the OR register: Output push-pull
and open-drain.
DR register value and output pin status:
DR
0
1
Push-pull
VSS
VDD
Open-drain
VSS
Floating
9.2.3 Alternate Functions
When an on-chip peripheral is configured to use a
pin, the alternate function is automatically selected. This alternate function takes priority over the
standard I/O programming.
When the signal is coming from an on-chip peripheral, the I/O pin is automatically configured in output mode (push-pull or open drain according to the
peripheral).
When the signal is going to an on-chip peripheral,
the I/O pin must be configured in input mode. In
this case, the pin state is also digitally readable by
addressing the DR register.
Note: Input pull-up configuration can cause unexpected value at the input of the alternate peripheral
input. When an on-chip peripheral use a pin as input and output, this pin has to be configured in input floating mode.
ST72104Gx-Auto, ST72215Gx-Auto, ST72216Gx-Auto, ST72254Gx-Auto
I/O PORTS (Cont’d)
Figure 20. I/O Port General Block Diagram
ALTERNATE
OUTPUT
REGISTER
ACCESS
1
VDD
0
P-BUFFER
(see table below)
ALTERNATE
ENABLE
PULL-UP
(see table below)
DR
VDD
DDR
PULL-UP
CONFIGURATION
DATA BUS
OR
PAD
If implemented
OR SEL
N-BUFFER
DIODES
(see table below)
DDR SEL
DR SEL
ANALOG
INPUT
CMOS
SCHMITT
TRIGGER
1
0
EXTERNAL
INTERRUPT
SOURCE (eix)
POLARITY
SELECTION
ALTERNATE
INPUT
FROM
OTHER
BITS
Table 6. I/O Port Mode Options
Configuration Mode
Input
Output
Floating with/without Interrupt
Pull-up with/without Interrupt
Push-pull
Open Drain (logic level)
True Open Drain
Legend: NI - not implemented
Off - implemented not activated
On - implemented and activated
Pull-Up
P-Buffer
Off
On
Off
Off
NI
On
Off
NI
Diodes
to VDD
On
to VSS
On
NI (see note)
Note: The diode to VDD is not implemented in the
true open drain pads. A local protection between
the pad and VSS is implemented to protect the device against positive stress.
31/135
ST72104Gx-Auto, ST72215Gx-Auto, ST72216Gx-Auto, ST72254Gx-Auto
I/O PORTS (Cont’d)
Table 7. I/O Port Configurations
Hardware Configuration
NOT IMPLEMENTED IN
TRUE OPEN DRAIN
I/O PORTS
DR REGISTER ACCESS
VDD
RPU
PULL-UP
CONFIGURATION
DR
REGISTER
PAD
W
DATA BUS
INPUT 1)
R
ALTERNATE INPUT
FROM
OTHER
PINS
INTERRUPT
CONFIGURATION
EXTERNAL INTERRUPT
SOURCE (eix)
POLARITY
SELECTION
PUSH-PULL OUTPUT 2)
OPEN-DRAIN OUTPUT 2)
ANALOG INPUT
NOT IMPLEMENTED IN
TRUE OPEN DRAIN
I/O PORTS
DR REGISTER ACCESS
VDD
RPU
DR
REGISTER
PAD
ALTERNATE
ENABLE
NOT IMPLEMENTED IN
TRUE OPEN DRAIN
I/O PORTS
R/W
DATA BUS
ALTERNATE
OUTPUT
DR REGISTER ACCESS
VDD
RPU
PAD
DR
REGISTER
ALTERNATE
ENABLE
R/W
DATA BUS
ALTERNATE
OUTPUT
Notes:
1. When the I/O port is in input configuration and the associated alternate function is enabled as an output, reading the
DR register will read the alternate function output status.
2. When the I/O port is in output configuration and the associated alternate function is enabled as an input, the alternate
function reads the pin status given by the DR register content.
32/135
ST72104Gx-Auto, ST72215Gx-Auto, ST72216Gx-Auto, ST72254Gx-Auto
I/O PORTS (Cont’d)
Caution: The alternate function must not be activated as long as the pin is configured as input with
interrupt, in order to avoid generating spurious interrupts.
Analog alternate function
When the pin is used as an ADC input, the I/O
must be configured as floating input. The analog
multiplexer (controlled by the ADC registers)
switches the analog voltage present on the selected pin to the common analog rail which is connected to the ADC input.
It is recommended not to change the voltage level
or loading on any port pin while conversion is in
progress. Furthermore it is recommended not to
have clocking pins located close to a selected analog pin.
Warning: The analog input voltage level must be
within the limits stated in the absolute maximum
ratings.
Figure 21. Interrupt I/O Port State Transitions
01
INPUT
INPUT
floating/pull-up floating
interrupt
(reset state)
10
11
OUTPUT
open-drain
OUTPUT
push-pull
XX = DDR, OR
The I/O port register configurations are summarized as follows.
Interrupt Ports
PA7, PA5, PA3:0, PB7:0, PC5:0 (with pull-up)
MODE
floating input
pull-up interrupt input
open drain output
push-pull output
9.3 I/O PORT IMPLEMENTATION
The hardware implementation on each I/O port depends on the settings in the DDR and OR registers
and specific feature of the I/O port such as ADC Input or true open drain.
Switching these I/O ports from one state to another should be done in a sequence that prevents unwanted side effects. Recommended safe transitions are illustrated in Figure 21. Other transitions
are potentially risky and should be avoided, since
they are likely to present unwanted side-effects
such as spurious interrupt generation.
00
DDR
0
0
1
1
OR
0
1
0
1
DDR
0
0
1
OR
0
1
X
True Open Drain Interrupt Ports
PA6, PA4 (without pull-up)
MODE
floating input
floating interrupt input
open drain (high sink ports)
Table 8. Port Configuration
Input (DDR = 0)
Port
Port A
Port B
Port C
Output (DDR = 1)
Pin name
PA7
PA6
PA5
PA4
PA3:0
PB7:0
PC7:0
OR = 0
OR = 1
floating
floating
floating
floating
floating
floating
floating
pull-up interrupt
floating interrupt
pull-up interrupt
floating interrupt
pull-up interrupt
pull-up interrupt
pull-up interrupt
OR = 0
OR = 1
open drain
push-pull
true open-drain
open drain
push-pull
true open-drain
open drain
push-pull
open drain
push-pull
open drain
push-pull
High-Sink
Yes
No
33/135
ST72104Gx-Auto, ST72215Gx-Auto, ST72216Gx-Auto, ST72254Gx-Auto
I/O PORTS (Cont’d)
9.4 LOW POWER MODES
Mode
Description
No effect on I/O ports. External interrupts
cause the device to exit from WAIT mode.
No effect on I/O ports. External interrupts
cause the device to exit from HALT mode.
WAIT
HALT
DATA DIRECTION REGISTER (DDR)
Port x Data Direction Register
PxDDR with x = A, B or C.
Read / Write
Reset Value: 0000 0000 (00h)
7
0
9.5 INTERRUPTS
The external interrupt event generates an interrupt
if the corresponding configuration is selected with
DDR and OR registers and the I-bit in the CC register is reset (RIM instruction).
Interrupt Event
External interrupt on
selected external
event
Enable
Event
Control
Flag
Bit
-
DDRx
ORx
Exit
from
Wait
Exit
from
Halt
Yes
Yes
DATA REGISTER (DR)
Port x Data Register
PxDR with x = A, B or C.
Read / Write
Reset Value: 0000 0000 (00h)
DD5
DD4
DD3
DD2
DD1
DD0
Bit 7:0 = DD[7:0] Data direction register 8 bits.
The DDR register gives the input/output direction
configuration of the pins. Each bit is set and
cleared by software.
0: Input mode
1: Output mode
7
O7
7
0
O6
O5
O4
O3
O2
O1
O0
0
D6
D5
D4
D3
D2
D1
D0
Bit 7:0 = D[7:0] Data register 8 bits.
The DR register has a specific behavior according
to the selected input/output configuration. Writing
the DR register is always taken into account even
if the pin is configured as an input; this allows always having the expected level on the pin when
toggling to output mode. Reading the DR register
returns either the DR register latch content (pin
configured as output) or the digital value applied to
the I/O pin (pin configured as input).
34/135
DD6
OPTION REGISTER (OR)
Port x Option Register
PxOR with x = A, B or C.
Read / Write
Reset Value: 0000 0000 (00h)
9.6 REGISTER DESCRIPTION
D7
DD7
Bit 7:0 = O[7:0] Option register 8 bits.
For specific I/O pins, this register is not implemented. In this case the DDR register is enough to select the I/O pin configuration.
The OR register allows to distinguish: in input
mode if the pull-up with interrupt capability or the
basic pull-up configuration is selected, in output
mode if the push-pull or open drain configuration is
selected.
Each bit is set and cleared by software.
Input mode:
0: Floating input
1: Pull-up input with or without interrupt
Output mode:
0: Output open drain (with P-Buffer deactivated)
1: Output push-pull (when available)
ST72104Gx-Auto, ST72215Gx-Auto, ST72216Gx-Auto, ST72254Gx-Auto
I/O PORTS (Cont’d)
Table 9. I/O Port Register Map and Reset Values
Address (Hex.)
Register Label
Reset Value of all I/O port registers
0000h
PCDR
0001h
PCDDR
0002h
PCOR
0004h
PBDR
0005h
PBDDR
0006h
PBOR
0008h
PADR
0009h
PADDR
000Ah
PAOR
7
6
5
4
3
2
1
0
0
0
0
0
0
0
0
0
MSB
LSB
MSB
LSB
MSB
LSB
35/135
ST72104Gx-Auto, ST72215Gx-Auto, ST72216Gx-Auto, ST72254Gx-Auto
10 MISCELLANEOUS REGISTERS
The miscellaneous registers allow control over
several different features such as the external interrupts or the I/O alternate functions.
10.1 I/O PORT INTERRUPT SENSITIVITY
The external interrupt sensitivity is controlled by
the ISxx bits of the Miscellaneous register and the
OPTION BYTE. This control allows having two fully independent external interrupt source sensitivities with configurable sources (using EXTIT option
bit) as shown in Figure 22 and Figure 23.
Each external interrupt source can be generated
on four different events on the pin:
■ Falling edge
■ Rising edge
■ Falling and rising edge
■ Falling edge and low level
To guarantee correct functionality, the sensitivity
bits in the MISCR1 register must be modified only
when the I bit of the CC register is set to 1 (interrupt masked). See I/O port register and Miscellaneous register descriptions for more details on the
programming.
Figure 22. Ext. Interrupt Sensitivity (EXTIT=0)
PA0
PC5
IS00
IS01
SENSITIVITY
CONTROL
MISCR1
PB7
ei1
INTERRUPT
SOURCE
IS10
IS11
SENSITIVITY
CONTROL
PB0
Figure 23. Ext. Interrupt Sensitivity (EXTIT=1)
MISCR1
10.2 I/O PORT ALTERNATE FUNCTIONS
36/135
ei0
INTERRUPT
SOURCE
PC0
PA7
The MISCR registers manage four I/O port miscellaneous alternate functions:
■ Main clock signal (fCPU) output on PC2
■ SPI pin configuration:
– SS pin internal control to use the PB7 I/O port
function while the SPI is active.
– Master output capability on MOSI pin (PB4)
deactivated while the SPI is active.
– Slave output capability on MISO pin (PB5) deactivated while the SPI is active.
These functions are described in detail in the Section 10.3 "MISCELLANEOUS REGISTER DESCRIPTION" on page 37.
MISCR1
PA7
ei0
INTERRUPT
SOURCE
IS00
IS01
SENSITIVITY
CONTROL
PA0
MISCR1
PB7
PB0
PC5
PC0
ei1
INTERRUPT
SOURCE
IS10
IS11
SENSITIVITY
CONTROL
ST72104Gx-Auto, ST72215Gx-Auto, ST72216Gx-Auto, ST72254Gx-Auto
MISCELLANEOUS REGISTERS (Cont’d)
10.3 MISCELLANEOUS REGISTER DESCRIPTION
MISCELLANEOUS REGISTER 1 (MISCR1)
Read / Write
Reset Value: 0000 0000 (00h)
7
IS11
Bit 2:1 = CP[1:0] CPU clock prescaler
These bits select the CPU clock prescaler which is
applied in the different slow modes. Their action is
conditioned by the setting of the SMS bit. These
two bits are set and cleared by software
0
IS10 MCO IS01
IS00
CP1
CP0
SMS
Bit 7:6 = IS1[1:0] ei1 sensitivity
The interrupt sensitivity, defined using the IS1[1:0]
bits, is applied to the ei1 external interrupts. These
two bits can be written only when the I bit of the CC
register is set to 1 (interrupt masked).
ei1: Port B (C optional)
External Interrupt Sensitivity
IS11 IS10
Falling edge & low level
0
0
Rising edge only
0
1
Falling edge only
1
0
Rising and falling edge
1
1
fCPU in SLOW mode
CP1
CP0
fOSC / 4
0
0
fOSC / 8
1
0
fOSC / 16
0
1
fOSC / 32
1
1
Bit 0 = SMS Slow mode select
This bit is set and cleared by software.
0: Normal mode. fCPU = fOSC / 2
1: Slow mode. fCPU is given by CP1, CP0
See low power consumption mode and MCC
chapters for more details.
Bit 5 = MCO Main clock out selection
This bit enables the MCO alternate function on the
PC2 I/O port. It is set and cleared by software.
0: MCO alternate function disabled (I/O pin free for
general-purpose I/O)
1: MCO alternate function enabled (fCPU on I/O
port)
Bit 4:3 = IS0[1:0] ei0 sensitivity
The interrupt sensitivity, defined using the IS0[1:0]
bits, is applied to the ei0 external interrupts. These
two bits can be written only when the I bit of the CC
register is set to 1 (interrupt masked).
ei0: Port A (C optional)
External Interrupt Sensitivity
IS01 IS00
Falling edge & low level
0
0
Rising edge only
0
1
Falling edge only
1
0
Rising and falling edge
1
1
37/135
ST72104Gx-Auto, ST72215Gx-Auto, ST72216Gx-Auto, ST72254Gx-Auto
MISCELLANEOUS REGISTERS (Cont’d)
MISCELLANEOUS REGISTER 2 (MISCR2)
Read / Write
Reset Value: 0000 0000 (00h)
7
0
0
0
0
0
MOD SOD SSM
SSI
Bit 7:4 = Reserved always read as 0
Bit 3 = MOD SPI Master Output Disable
This bit is set and cleared by software. When set, it
disables the SPI Master (MOSI) output signal.
0: SPI Master Output enabled.
1: SPI Master Output disabled.
Bit 2 = SOD SPI Slave Output Disable
This bit is set and cleared by software. When set it
disable the SPI Slave (MISO) output signal.
0: SPI Slave Output enabled.
1: SPI Slave Output disabled.
Bit 1 = SSM SS mode selection
This bit is set and cleared by software.
0: Normal mode - the level of the SPI SS signal is
input from the external SS pin.
1: I/O mode, the level of the SPI SS signal is read
from the SSI bit.
Bit 0 = SSI SS internal mode
This bit replaces the SS pin of the SPI when the
SSM bit is set to 1. (see SPI description). It is set
and cleared by software.
Table 10. Miscellaneous Register Map and Reset Values
Address
(Hex.)
Register
Label
7
6
5
4
3
2
1
0
0020h
MISCR1
Reset Value
IS11
0
IS10
0
MCO
0
IS01
0
IS00
0
CP1
0
CP0
0
SMS
0
0040h
MISCR2
Reset Value
0
0
0
0
MOD
0
SOD
0
SSM
0
SSI
0
38/135
ST72104Gx-Auto, ST72215Gx-Auto, ST72216Gx-Auto, ST72254Gx-Auto
11 ON-CHIP PERIPHERALS
11.1 WATCHDOG TIMER (WDG)
11.1.1 Introduction
The Watchdog timer is used to detect the occurrence of a software fault, usually generated by external interference or by unforeseen logical conditions, which causes the application program to
abandon its normal sequence. The Watchdog circuit generates an MCU reset on expiry of a programmed time period, unless the program refreshes the counter’s contents before the T6 bit becomes cleared.
11.1.2 Main Features
■ Programmable timer (64 increments of 12288
CPU cycles)
■ Programmable reset
■ Reset (if watchdog activated) when the T6 bit
reaches zero
■ Optional
reset
on
HALT
instruction
(configurable by option byte)
■ Hardware Watchdog selectable by option byte
11.1.3 Functional Description
The counter value stored in the CR register (bits
T6:T0), is decremented every 12288 machine cycles, and the length of the timeout period can be
programmed by the user in 64 increments.
If the watchdog is activated (the WDGA bit is set)
and when the 7-bit timer (bits T6:T0) rolls over
from 40h to 3Fh (T6 becomes cleared), it initiates
a reset cycle pulling low the RESET pin for typically 30µs.
The application program must write in the CR register at regular intervals during normal operation to
prevent an MCU reset. The value to be stored in
the CR register must be between FFh and C0h
(see Table 11 Watchdog Timing (fCPU = 8 MHz)):
– The WDGA bit is set (watchdog enabled)
– The T6 bit is set to prevent generating an immediate reset
– The T5:T0 bits contain the number of increments
which represents the time delay before the
watchdog produces a reset.
Figure 24. Watchdog Block Diagram
RESET
WATCHDOG CONTROL REGISTER (CR)
WDGA
T6
T5
T4
T3
T2
T1
T0
7-BIT DOWNCOUNTER
fCPU
CLOCK DIVIDER
÷12288
39/135
ST72104Gx-Auto, ST72215Gx-Auto, ST72216Gx-Auto, ST72254Gx-Auto
WATCHDOG TIMER (Cont’d)
Table 11. Watchdog Timing (fCPU = 8 MHz)
CR Register
initial value
WDG timeout period
(ms)
Max
FFh
98.304
Min
C0h
1.536
Notes: Following a reset, the watchdog is disabled. Once activated it cannot be disabled, except
by a reset.
The T6 bit can be used to generate a software reset (the WDGA bit is set and the T6 bit is cleared).
11.1.4 Hardware Watchdog Option
If Hardware Watchdog is selected by option byte,
the watchdog is always active and the WDGA bit in
the CR is not used.
Refer to the device-specific Option Byte description.
11.1.5 Low Power Modes
WAIT Instruction
No effect on Watchdog.
HALT Instruction
If the Watchdog reset on HALT option is selected
by option byte, a HALT instruction causes an immediate reset generation if the Watchdog is activated (WDGA bit is set).
11.1.5.1 Using Halt Mode with the WDG (option)
If the Watchdog reset on HALT option is not selected by option byte, the Halt mode can be used
when the watchdog is enabled.
In this case, the HALT instruction stops the oscillator. When the oscillator is stopped, the WDG stops
counting and is no longer able to generate a reset
until the microcontroller receives an external interrupt or a reset.
If an external interrupt is received, the WDG restarts counting after 4096 CPU clocks. If a reset is
generated, the WDG is disabled (reset state).
Recommendations
– Make sure that an external event is available to
wake up the microcontroller from Halt mode.
– Before executing the HALT instruction, refresh
the WDG counter, to avoid an unexpected WDG
reset immediately after waking up the microcontroller.
40/135
– When using an external interrupt to wake up the
microcontroller, reinitialize the corresponding I/O
as “Input Pull-up with Interrupt” before executing
the HALT instruction. The main reason for this is
that the I/O may be wrongly configured due to external interference or by an unforeseen logical
condition.
– For the same reason, reinitialize the level sensitiveness of each external interrupt as a precautionary measure.
– The opcode for the HALT instruction is 0x8E. To
avoid an unexpected HALT instruction due to a
program counter failure, it is advised to clear all
occurrences of the data value 0x8E from memory. For example, avoid defining a constant in
ROM with the value 0x8E.
– As the HALT instruction clears the I bit in the CC
register to allow interrupts, the user may choose
to clear all pending interrupt bits before executing the HALT instruction. This avoids entering
other peripheral interrupt routines after executing
the external interrupt routine corresponding to
the wake-up event (reset or external interrupt).
11.1.6 Interrupts
None.
11.1.7 Register Description
CONTROL REGISTER (CR)
Read / Write
Reset Value: 0111 1111 (7F h)
7
WDGA
0
T6
T5
T4
T3
T2
T1
T0
Bit 7 = WDGA Activation bit.
This bit is set by software and only cleared by
hardware after a reset. When WDGA = 1, the
watchdog can generate a reset.
0: Watchdog disabled
1: Watchdog enabled
Bit 6:0 = T[6:0] 7-bit timer (MSB to LSB).
These bits contain the decremented value. A reset
is produced when it rolls over from 40h to 3Fh (T6
becomes cleared).
ST72104Gx-Auto, ST72215Gx-Auto, ST72216Gx-Auto, ST72254Gx-Auto
WATCHDOG TIMER (Cont’d)
Table 12. Watchdog Timer Register Map and Reset Values
Address
(Hex.)
Register
Label
7
6
5
4
3
2
1
0
0024h
WDGCR
Reset Value
WDGA
0
T6
1
T5
1
T4
1
T3
1
T2
1
T1
1
T0
1
41/135
ST72104Gx-Auto, ST72215Gx-Auto, ST72216Gx-Auto, ST72254Gx-Auto
11.2 16-BIT TIMER
11.2.1 Introduction
The timer consists of a 16-bit free-running counter
driven by a programmable prescaler.
It may be used for a variety of purposes, including
measuring the pulse lengths of up to two input signals (input capture) or generating up to two output
waveforms (output compare and PWM).
Pulse lengths and waveform periods can be modulated from a few microseconds to several milliseconds using the timer prescaler and the CPU
clock prescaler.
Some ST7 devices have two on-chip 16-bit timers.
They are completely independent, and do not
share any resources. They are synchronized after
a MCU reset as long as the timer clock frequencies are not modified.
This description covers one or two 16-bit timers. In
ST7 devices with two timers, register names are
prefixed with TA (Timer A) or TB (Timer B).
11.2.2 Main Features
■ Programmable prescaler: fCPU divided by 2, 4 or
8.
■ Overflow status flag and maskable interrupt
■ External clock input (must be at least 4 times
slower than the CPU clock speed) with the choice
of active edge
■ Output compare functions with:
– 2 dedicated 16-bit registers
– 2 dedicated programmable signals
– 2 dedicated status flags
– 1 dedicated maskable interrupt
■ Input capture functions with:
– 2 dedicated 16-bit registers
– 2 dedicated active edge selection signals
– 2 dedicated status flags
– 1 dedicated maskable interrupt
■ Pulse Width Modulation mode (PWM)
■ One Pulse mode
■ 5 alternate functions on I/O ports (ICAP1, ICAP2,
OCMP1, OCMP2, EXTCLK)*
The Block Diagram is shown in Figure 25.
*Note: Some timer pins may not be available (not
bonded) in some ST7 devices. Refer to the device
pinout description.
42/135
When reading an input signal on a non-bonded
pin, the value will always be ‘1’.
11.2.3 Functional Description
11.2.3.1 Counter
The main block of the Programmable Timer is a
16-bit free running upcounter and its associated
16-bit registers. The 16-bit registers are made up
of two 8-bit registers called high and low.
Counter Register (CR)
– Counter High Register (CHR) is the most significant byte (MS Byte).
– Counter Low Register (CLR) is the least significant byte (LS Byte).
Alternate Counter Register (ACR)
– Alternate Counter High Register (ACHR) is
the most significant byte (MS Byte).
– Alternate Counter Low Register (ACLR) is the
least significant byte (LS Byte).
These two read-only 16-bit registers contain the
same value but with the difference that reading the
ACLR register does not clear the TOF bit (Timer
overflow flag), located in the Status register (SR).
(See note at the end of paragraph titled 16-bit read
sequence).
Writing in the CLR register or ACLR register resets
the free running counter to the FFFCh value.
Both counters have a reset value of FFFCh (this is
the only value which is reloaded in the 16-bit timer). The reset value of both counters is also
FFFCh in One Pulse mode and PWM mode.
The timer clock depends on the clock control bits
of the CR2 register, as illustrated in Table 13 Clock
Control Bits. The value in the counter register repeats every 131072, 262144 or 524288 CPU clock
cycles depending on the CC[1:0] bits.
The timer frequency can be fCPU/2, fCPU/4, fCPU/8
or an external frequency.
ST72104Gx-Auto, ST72215Gx-Auto, ST72216Gx-Auto, ST72254Gx-Auto
16-BIT TIMER (Cont’d)
Figure 25. Timer Block Diagram
ST7 INTERNAL BUS
fCPU
MCU-PERIPHERAL INTERFACE
8 low
8
8
8
low
8
high
8
low
8
high
EXEDG
8
low
high
8
high
8-bit
buffer
low
8 high
16
1/2
1/4
1/8
OUTPUT
COMPARE
REGISTER
2
OUTPUT
COMPARE
REGISTER
1
COUNTER
REGISTER
ALTERNATE
COUNTER
REGISTER
EXTCLK
pin
INPUT
CAPTURE
REGISTER
1
INPUT
CAPTURE
REGISTER
2
16
16
16
CC[1:0]
TIMER INTERNAL BUS
16 16
OVERFLOW
DETECT
CIRCUIT
OUTPUT COMPARE
CIRCUIT
6
ICF1 OCF1 TOF ICF2 OCF2 0
0
EDGE DETECT
CIRCUIT1
ICAP1
pin
EDGE DETECT
CIRCUIT2
ICAP2
pin
LATCH1
OCMP1
pin
LATCH2
OCMP2
pin
0
(Status Register) SR
ICIE OCIE TOIE FOLV2 FOLV1 OLVL2 IEDG1 OLVL1
(Control Register 1) CR1
OC1E OC2E OPM PWM
CC1
CC0 IEDG2 EXEDG
(Control Register 2) CR2
(See note)
TIMER INTERRUPT
Note: If IC, OC and TO interrupt requests have separate vectors
then the last OR is not present (See device Interrupt Vector Table)
43/135
ST72104Gx-Auto, ST72215Gx-Auto, ST72216Gx-Auto, ST72254Gx-Auto
16-BIT TIMER (Cont’d)
16-bit Read Sequence: (from either the Counter
Register or the Alternate Counter Register).
Beginning of the sequence
At t0
Read
MS Byte
LS Byte
is buffered
Other
instructions
Read
At t0 +∆t LS Byte
Returns the buffered
LS Byte value at t0
Sequence completed
The user must read the MS Byte first, then the LS
Byte value is buffered automatically.
This buffered value remains unchanged until the
16-bit read sequence is completed, even if the
user reads the MS Byte several times.
After a complete reading sequence, if only the
CLR register or ACLR register are read, they return the LS Byte of the count value at the time of
the read.
Whatever the timer mode used (input capture, output compare, One Pulse mode or PWM mode) an
overflow occurs when the counter rolls over from
FFFFh to 0000h then:
– The TOF bit of the SR register is set.
– A timer interrupt is generated if:
– TOIE bit of the CR1 register is set and
– I bit of the CC register is cleared.
If one of these conditions is false, the interrupt remains pending to be issued as soon as they are
both true.
44/135
Clearing the overflow interrupt request is done in
two steps:
1.Reading the SR register while the TOF bit is set.
2.An access (read or write) to the CLR register.
Note: The TOF bit is not cleared by accessing the
ACLR register. The advantage of accessing the
ACLR register rather than the CLR register is that
it allows simultaneous use of the overflow function
and reading the free running counter at random
times (for example, to measure elapsed time) without the risk of clearing the TOF bit erroneously.
The timer is not affected by WAIT mode.
In HALT mode, the counter stops counting until the
mode is exited. Counting then resumes from the
previous count (MCU awakened by an interrupt) or
from the reset count (MCU awakened by a Reset).
11.2.3.2 External Clock
The external clock (where available) is selected if
CC0 = 1 and CC1 = 1 in the CR2 register.
The status of the EXEDG bit in the CR2 register
determines the type of level transition on the external clock pin EXTCLK that will trigger the free running counter.
The counter is synchronized with the falling edge
of the internal CPU clock.
A minimum of four falling edges of the CPU clock
must occur between two consecutive active edges
of the external clock; thus the external clock frequency must be less than a quarter of the CPU
clock frequency.
ST72104Gx-Auto, ST72215Gx-Auto, ST72216Gx-Auto, ST72254Gx-Auto
16-BIT TIMER (Cont’d)
Figure 26. Counter Timing Diagram, internal clock divided by 2
CPU CLOCK
INTERNAL RESET
TIMER CLOCK
FFFD FFFE FFFF 0000
COUNTER REGISTER
0001
0002
0003
TIMER OVERFLOW FLAG (TOF)
Figure 27. Counter Timing Diagram, internal clock divided by 4
CPU CLOCK
INTERNAL RESET
TIMER CLOCK
COUNTER REGISTER
FFFC
FFFD
0000
0001
TIMER OVERFLOW FLAG (TOF)
Figure 28. Counter Timing Diagram, internal clock divided by 8
CPU CLOCK
INTERNAL RESET
TIMER CLOCK
COUNTER REGISTER
FFFC
FFFD
0000
TIMER OVERFLOW FLAG (TOF)
Note: The MCU is in reset state when the internal reset signal is high. When it is low, the MCU is running.
45/135
ST72104Gx-Auto, ST72215Gx-Auto, ST72216Gx-Auto, ST72254Gx-Auto
16-BIT TIMER (Cont’d)
11.2.3.3 Input Capture
In this section, the index, i, may be 1 or 2 because
there are two input capture functions in the 16-bit
timer.
The two input capture 16-bit registers (IC1R and
IC2R) are used to latch the value of the free running counter after a transition is detected by the
ICAPi pin (see Figure 29).
ICiR
MS Byte
ICiHR
LS Byte
ICiLR
The ICiR register is a read-only register.
The active transition is software programmable
through the IEDGi bit of Control Registers (CRi).
Timing resolution is one count of the free running
counter: (fCPU/CC[1:0]).
Procedure:
To use the input capture function, select the following in the CR2 register:
– Select the timer clock (CC[1:0]) (see Table 13
Clock Control Bits).
– Select the edge of the active transition on the
ICAP2 pin with the IEDG2 bit (the ICAP2 pin
must be configured as a floating input or input
with pull-up without interrupt if this configuration
is available).
And select the following in the CR1 register:
– Set the ICIE bit to generate an interrupt after an
input capture coming from either the ICAP1 pin
or the ICAP2 pin
– Select the edge of the active transition on the
ICAP1 pin with the IEDG1 bit (the ICAP1 pin
must be configured as a floating input or input
with pull-up without interrupt if this configuration
is available).
46/135
When an input capture occurs:
– The ICFi bit is set.
– The ICiR register contains the value of the free
running counter on the active transition on the
ICAPi pin (see Figure 30).
– A timer interrupt is generated if the ICIE bit is set
and the I bit is cleared in the CC register. Otherwise, the interrupt remains pending until both
conditions become true.
Clearing the Input Capture interrupt request (i.e.
clearing the ICFi bit) is done in two steps:
1. Reading the SR register while the ICFi bit is set.
2. An access (read or write) to the ICiLR register.
Notes:
1. After reading the ICiHR register, the transfer of
input capture data is inhibited and ICFi will
never be set until the ICiLR register is also
read.
2. The ICiR register contains the free running
counter value which corresponds to the most
recent input capture.
3. The two input capture functions can be used
together even if the timer also uses the two output compare functions.
4. In One Pulse mode and PWM mode only the
input capture 2 function can be used.
5. The alternate inputs (ICAP1 and ICAP2) are
always directly connected to the timer. So any
transitions on these pins activate the input capture function.
Moreover if one of the ICAPi pin is configured
as an input and the second one as an output,
an interrupt can be generated if the user toggles the output pin and if the ICIE bit is set.
This can be avoided if the input capture function i is disabled by reading the ICiHR (see note
1).
6. The TOF bit can be used with an interrupt in
order to measure events that exceed the timer
range (FFFFh).
ST72104Gx-Auto, ST72215Gx-Auto, ST72216Gx-Auto, ST72254Gx-Auto
16-BIT TIMER (Cont’d)
Figure 29. Input Capture Block Diagram
ICAP1
pin
ICAP2
pin
(Control Register 1) CR1
EDGE DETECT
CIRCUIT2
EDGE DETECT
CIRCUIT1
ICIE
IEDG1
(Status Register) SR
IC2R Register
IC1R Register
ICF1
ICF2
0
0
0
(Control Register 2) CR2
16-BIT
16-BIT FREE RUNNING
CC1
CC0 IEDG2
COUNTER
Figure 30. Input Capture Timing Diagram
TIMER CLOCK
COUNTER REGISTER
FF01
FF02
FF03
ICAPi PIN
ICAPi FLAG
ICAPi REGISTER
FF03
Note: Active edge is rising edge.
47/135
ST72104Gx-Auto, ST72215Gx-Auto, ST72216Gx-Auto, ST72254Gx-Auto
16-BIT TIMER (Cont’d)
11.2.3.4 Output Compare
In this section, the index, i, may be 1 or 2 because
there are 2 output compare functions in the 16-bit
timer.
This function can be used to control an output
waveform or indicate when a period of time has
elapsed.
When a match is found between the Output Compare register and the free running counter, the output compare function:
– Assigns pins with a programmable value if the
OCiE bit is set
– Sets a flag in the status register
– Generates an interrupt if enabled
Two 16-bit registers Output Compare Register 1
(OC1R) and Output Compare Register 2 (OC2R)
contain the value to be compared to the counter
register each timer clock cycle.
OCiR
MS Byte
OCiHR
LS Byte
OCiLR
These registers are readable and writable and are
not affected by the timer hardware. A reset event
changes the OCiR value to 8000h.
Timing resolution is one count of the free running
counter: (fCPU/CC[1:0]).
Procedure:
To use the output compare function, select the following in the CR2 register:
– Set the OCiE bit if an output is needed then the
OCMPi pin is dedicated to the output compare i
signal.
– Select the timer clock (CC[1:0]) (see Table 13
Clock Control Bits).
And select the following in the CR1 register:
– Select the OLVLi bit to applied to the OCMPi pins
after the match occurs.
– Set the OCIE bit to generate an interrupt if it is
needed.
When a match is found between OCRi register
and CR register:
– OCFi bit is set.
48/135
– The OCMPi pin takes OLVLi bit value (OCMPi
pin latch is forced low during reset).
– A timer interrupt is generated if the OCIE bit is
set in the CR1 register and the I bit is cleared in
the CC register (CC).
The OCiR register value required for a specific timing application can be calculated using the following formula:
∆ OCiR =
∆t * fCPU
PRESC
Where:
∆t
= Output compare period (in seconds)
fCPU
= CPU clock frequency (in hertz)
=
Timer prescaler factor (2, 4 or 8 dePRESC
pending on CC[1:0] bits, see Table 13
Clock Control Bits)
If the timer clock is an external clock, the formula
is:
∆ OCiR = ∆t * fEXT
Where:
∆t
= Output compare period (in seconds)
fEXT
= External timer clock frequency (in hertz)
Clearing the output compare interrupt request (i.e.
clearing the OCFi bit) is done by:
1. Reading the SR register while the OCFi bit is
set.
2. An access (read or write) to the OCiLR register.
The following procedure is recommended to prevent the OCFi bit from being set between the time
it is read and the write to the OCiR register:
– Write to the OCiHR register (further compares
are inhibited).
– Read the SR register (first step of the clearance
of the OCFi bit, which may be already set).
– Write to the OCiLR register (enables the output
compare function and clears the OCFi bit).
ST72104Gx-Auto, ST72215Gx-Auto, ST72216Gx-Auto, ST72254Gx-Auto
16-BIT TIMER (Cont’d)
Notes:
1. After a processor write cycle to the OCiHR register, the output compare function is inhibited
until the OCiLR register is also written.
2. If the OCiE bit is not set, the OCMPi pin is a
general I/O port and the OLVLi bit will not
appear when a match is found but an interrupt
could be generated if the OCIE bit is set.
3. When the timer clock is fCPU/2, OCFi and
OCMPi are set while the counter value equals
the OCiR register value (see Figure 32 on page
50). This behavior is the same in OPM or PWM
mode.
When the timer clock is fCPU/4, fCPU/8 or in
external clock mode, OCFi and OCMPi are set
while the counter value equals the OCiR register value plus 1 (see Figure 33 on page 50).
4. The output compare functions can be used both
for generating external events on the OCMPi
pins even if the input capture mode is also
used.
5. The value in the 16-bit OCiR register and the
OLVi bit should be changed after each successful comparison in order to control an output
waveform or establish a new elapsed timeout.
Forced Compare Output capability
When the FOLVi bit is set by software, the OLVLi
bit is copied to the OCMPi pin. The OLVi bit has to
be toggled in order to toggle the OCMPi pin when
it is enabled (OCiE bit = 1). The OCFi bit is then
not set by hardware, and thus no interrupt request
is generated.
FOLVLi bits have no effect in either One-Pulse
mode or PWM mode.
Figure 31. Output Compare Block Diagram
16 BIT FREE RUNNING
COUNTER
OC1E OC2E
CC1
CC0
(Control Register 2) CR2
16-bit
(Control Register 1) CR1
OUTPUT COMPARE
CIRCUIT
16-bit
OCIE
FOLV2 FOLV1 OLVL2
OLVL1
16-bit
Latch
1
Latch
2
OC1R Register
OCF1
OCF2
0
0
OCMP1
Pin
OCMP2
Pin
0
OC2R Register
(Status Register) SR
49/135
ST72104Gx-Auto, ST72215Gx-Auto, ST72216Gx-Auto, ST72254Gx-Auto
16-BIT TIMER (Cont’d)
Figure 32. Output Compare Timing Diagram, fTIMER = fCPU/2
INTERNAL CPU CLOCK
TIMER CLOCK
COUNTER REGISTER
2ECF 2ED0
OUTPUT COMPARE REGISTER i (OCRi)
2ED1 2ED2 2ED3 2ED4
2ED3
OUTPUT COMPARE FLAG i (OCFi)
OCMPi PIN (OLVLi = 1)
Figure 33. Output Compare Timing Diagram, fTIMER = fCPU/4
INTERNAL CPU CLOCK
TIMER CLOCK
COUNTER REGISTER
OUTPUT COMPARE REGISTER i (OCRi)
COMPARE REGISTER i LATCH
OUTPUT COMPARE FLAG i (OCFi)
OCMPi PIN (OLVLi = 1)
50/135
2ECF 2ED0
2ED1 2ED2 2ED3 2ED4
2ED3
ST72104Gx-Auto, ST72215Gx-Auto, ST72216Gx-Auto, ST72254Gx-Auto
16-BIT TIMER (Cont’d)
11.2.3.5 One Pulse Mode
One Pulse mode enables the generation of a
pulse when an external event occurs. This mode is
selected via the OPM bit in the CR2 register.
The One Pulse mode uses the Input Capture1
function and the Output Compare1 function.
Procedure:
To use One Pulse mode:
1. Load the OC1R register with the value corresponding to the length of the pulse (see the formula in the opposite column).
2. Select the following in the CR1 register:
– Using the OLVL1 bit, select the level to be applied to the OCMP1 pin after the pulse.
– Using the OLVL2 bit, select the level to be applied to the OCMP1 pin during the pulse.
– Select the edge of the active transition on the
ICAP1 pin with the IEDG1 bit (the ICAP1 pin
must be configured as floating input).
3. Select the following in the CR2 register:
– Set the OC1E bit, the OCMP1 pin is then dedicated to the Output Compare 1 function.
– Set the OPM bit.
– Select the timer clock CC[1:0] (see Table 13
Clock Control Bits).
One Pulse mode cycle
When
event occurs
on ICAP1
OCMP1 = OLVL2
Counter is reset
to FFFCh
ICF1 bit is set
When
Counter
= OC1R
OCMP1 = OLVL1
Then, on a valid event on the ICAP1 pin, the counter is initialized to FFFCh and the OLVL2 bit is
loaded on the OCMP1 pin, the ICF1 bit is set and
the value FFFDh is loaded in the IC1R register.
Because the ICF1 bit is set when an active edge
occurs, an interrupt can be generated if the ICIE
bit is set.
Clearing the Input Capture interrupt request (i.e.
clearing the ICFi bit) is done in two steps:
1. Reading the SR register while the ICFi bit is set.
2. An access (read or write) to the ICiLR register.
The OC1R register value required for a specific
timing application can be calculated using the following formula:
OCiR Value =
t * fCPU
-5
PRESC
Where:
t
= Pulse period (in seconds)
fCPU = CPU clock frequency (in hertz)
PRESC = Timer prescaler factor (2, 4 or 8 depending on the CC[1:0] bits, see Table 13
Clock Control Bits)
If the timer clock is an external clock the formula is:
OCiR = t * fEXT -5
Where:
t
= Pulse period (in seconds)
fEXT
= External timer clock frequency (in hertz)
When the value of the counter is equal to the value
of the contents of the OC1R register, the OLVL1
bit is output on the OCMP1 pin (see Figure 34).
Notes:
1. The OCF1 bit cannot be set by hardware in
One Pulse mode but the OCF2 bit can generate
an Output Compare interrupt.
2. When the Pulse Width Modulation (PWM) and
One Pulse mode (OPM) bits are both set, the
PWM mode is the only active one.
3. If OLVL1 = OLVL2 a continuous signal will be
seen on the OCMP1 pin.
4. The ICAP1 pin cannot be used to perform input
capture. The ICAP2 pin can be used to perform
input capture (ICF2 can be set and IC2R can be
loaded) but the user must take care that the
counter is reset each time a valid edge occurs
on the ICAP1 pin and ICF1 can also generates
interrupt if ICIE is set.
5. When One Pulse mode is used OC1R is dedicated to this mode. Nevertheless OC2R and
OCF2 can be used to indicate that a period of
time has elapsed but cannot generate an output
waveform because the OLVL2 level is dedicated to One Pulse mode.
51/135
ST72104Gx-Auto, ST72215Gx-Auto, ST72216Gx-Auto, ST72254Gx-Auto
16-BIT TIMER (Cont’d)
Figure 34. One Pulse Mode Timing Example
COUNTER
FFFC FFFD FFFE
2ED0 2ED1 2ED2
FFFC FFFD
2ED3
ICAP1
OLVL2
OCMP1
OLVL1
OLVL2
compare1
Note: IEDG1 = 1, OC1R = 2ED0h, OLVL1 = 0, OLVL2 = 1
Figure 35. Pulse Width Modulation Mode Timing Example
COUNTER 34E2 FFFC FFFD FFFE
2ED0 2ED1 2ED2
OLVL2
OCMP1
compare2
OLVL1
compare1
Note: OC1R = 2ED0h, OC2R = 34E2, OLVL1 = 0, OLVL2 = 1
52/135
34E2
FFFC
OLVL2
compare2
ST72104Gx-Auto, ST72215Gx-Auto, ST72216Gx-Auto, ST72254Gx-Auto
16-BIT TIMER (Cont’d)
11.2.3.6 Pulse Width Modulation Mode
Pulse Width Modulation (PWM) mode enables the
generation of a signal with a frequency and pulse
length determined by the value of the OC1R and
OC2R registers.
The Pulse Width Modulation mode uses the complete Output Compare 1 function plus the OC2R
register, and so these functions cannot be used
when the PWM mode is activated.
Procedure
To use Pulse Width Modulation mode:
1. Load the OC2R register with the value corresponding to the period of the signal using the
formula in the opposite column.
2. Load the OC1R register with the value corresponding to the period of the pulse if OLVL1 = 0
and OLVL2 = 1, using the formula in the opposite column.
3. Select the following in the CR1 register:
– Using the OLVL1 bit, select the level to be applied to the OCMP1 pin after a successful
comparison with OC1R register.
– Using the OLVL2 bit, select the level to be applied to the OCMP1 pin after a successful
comparison with OC2R register.
4. Select the following in the CR2 register:
– Set OC1E bit: the OCMP1 pin is then dedicated to the output compare 1 function.
– Set the PWM bit.
– Select the timer clock (CC[1:0]) (see Table 13
Clock Control Bits).
If OLVL1 = 1 and OLVL2 = 0, the length of the
positive pulse is the difference between the OC2R
and OC1R registers.
If OLVL1 = OLVL2 a continuous signal will be
seen on the OCMP1 pin.
Pulse Width Modulation cycle
When
Counter
= OC1R
When
Counter
= OC2R
OCMP1 = OLVL1
The OCiR register value required for a specific timing application can be calculated using the following formula:
OCiR Value =
t * fCPU
-5
PRESC
Where:
t
= Signal or pulse period (in seconds)
fCPU = CPU clock frequency (in hertz)
PRESC = Timer prescaler factor (2, 4 or 8 depending on CC[1:0] bits, see Table 13 Clock
Control Bits)
If the timer clock is an external clock the formula is:
OCiR = t * fEXT -5
Where:
t
= Signal or pulse period (in seconds)
fEXT
= External timer clock frequency (in hertz)
The Output Compare 2 event causes the counter
to be initialized to FFFCh (See Figure 35)
Notes:
1. After a write instruction to the OCiHR register,
the output compare function is inhibited until the
OCiLR register is also written.
2. The OCF1 and OCF2 bits cannot be set by
hardware in PWM mode, therefore the Output
Compare interrupt is inhibited.
3. The ICF1 bit is set by hardware when the counter reaches the OC2R value and can produce a
timer interrupt if the ICIE bit is set and the I bit is
cleared.
4. In PWM mode the ICAP1 pin cannot be used to
perform input capture because it is disconnected from the timer. The ICAP2 pin can be
used to perform input capture (ICF2 can be set
and IC2R can be loaded) but the user must
take care that the counter is reset after each
period and ICF1 can also generate an interrupt
if ICIE is set.
5. When the Pulse Width Modulation (PWM) and
One Pulse mode (OPM) bits are both set, the
PWM mode is the only active one.
OCMP1 = OLVL2
Counter is reset
to FFFCh
ICF1 bit is set
53/135
ST72104Gx-Auto, ST72215Gx-Auto, ST72216Gx-Auto, ST72254Gx-Auto
16-BIT TIMER (Cont’d)
11.2.4 Low Power Modes
Mode
WAIT
HALT
Description
No effect on 16-bit Timer.
Timer interrupts cause the device to exit from WAIT mode.
16-bit Timer registers are frozen.
In HALT mode, the counter stops counting until Halt mode is exited. Counting resumes from the previous
count when the MCU is woken up by an interrupt with “exit from HALT mode” capability or from the counter
reset value when the MCU is woken up by a RESET.
If an input capture event occurs on the ICAPi pin, the input capture detection circuitry is armed. Consequently, when the MCU is woken up by an interrupt with “exit from HALT mode” capability, the ICFi bit is set, and
the counter value present when exiting from HALT mode is captured into the ICiR register.
11.2.5 Interrupts
Event
Flag
Interrupt Event
Input Capture 1 event/Counter reset in PWM mode
Input Capture 2 event
Output Compare 1 event (not available in PWM mode)
Output Compare 2 event (not available in PWM mode)
Timer Overflow event
ICF1
ICF2
OCF1
OCF2
TOF
Enable
Control
Bit
ICIE
OCIE
TOIE
Exit
from
Wait
Yes
Yes
Yes
Yes
Yes
Exit
from
Halt
No
No
No
No
No
Note: The 16-bit Timer interrupt events are connected to the same interrupt vector (see Interrupts chapter). These events generate an interrupt if the corresponding Enable Control Bit is set and the interrupt
mask in the CC register is reset (RIM instruction).
11.2.6 Summary of Timer Modes
MODES
Input Capture (1 and/or 2)
Output Compare (1 and/or 2)
One Pulse mode
PWM Mode
Input Capture 1
Yes
Yes
No
No
AVAILABLE RESOURCES
Input Capture 2
Output Compare 1 Output Compare 2
Yes
Yes
Yes
Yes
Yes
Yes
Not recommended1)
No
Partially 2)
Not recommended3)
No
No
Notes:
1. See note 4 in Section 11.2.3.5 "One Pulse Mode" on page 51.
2. See note 5 in Section 11.2.3.5 "One Pulse Mode" on page 51.
3. See note 4 in Section 11.2.3.6 "Pulse Width Modulation Mode" on page 53.
54/135
ST72104Gx-Auto, ST72215Gx-Auto, ST72216Gx-Auto, ST72254Gx-Auto
16-BIT TIMER (Cont’d)
11.2.7 Register Description
Each Timer is associated with three control and
status registers, and with six pairs of data registers
(16-bit values) relating to the two input captures,
the two output compares, the counter and the alternate counter.
CONTROL REGISTER 1 (CR1)
Read/Write
Reset Value: 0000 0000 (00h)
7
0
Bit 4 = FOLV2 Forced Output Compare 2.
This bit is set and cleared by software.
0: No effect on the OCMP2 pin.
1: Forces the OLVL2 bit to be copied to the
OCMP2 pin, if the OC2E bit is set and even if
there is no successful comparison.
Bit 3 = FOLV1 Forced Output Compare 1.
This bit is set and cleared by software.
0: No effect on the OCMP1 pin.
1: Forces OLVL1 to be copied to the OCMP1 pin, if
the OC1E bit is set and even if there is no successful comparison.
ICIE OCIE TOIE FOLV2 FOLV1 OLVL2 IEDG1 OLVL1
Bit 7 = ICIE Input Capture Interrupt Enable.
0: Interrupt is inhibited.
1: A timer interrupt is generated whenever the
ICF1 or ICF2 bit of the SR register is set.
Bit 6 = OCIE Output Compare Interrupt Enable.
0: Interrupt is inhibited.
1: A timer interrupt is generated whenever the
OCF1 or OCF2 bit of the SR register is set.
Bit 5 = TOIE Timer Overflow Interrupt Enable.
0: Interrupt is inhibited.
1: A timer interrupt is enabled whenever the TOF
bit of the SR register is set.
Bit 2 = OLVL2 Output Level 2.
This bit is copied to the OCMP2 pin whenever a
successful comparison occurs with the OC2R register and OCxE is set in the CR2 register. This value is copied to the OCMP1 pin in One Pulse mode
and Pulse Width Modulation mode.
Bit 1 = IEDG1 Input Edge 1.
This bit determines which type of level transition
on the ICAP1 pin will trigger the capture.
0: A falling edge triggers the capture.
1: A rising edge triggers the capture.
Bit 0 = OLVL1 Output Level 1.
The OLVL1 bit is copied to the OCMP1 pin whenever a successful comparison occurs with the
OC1R register and the OC1E bit is set in the CR2
register.
55/135
ST72104Gx-Auto, ST72215Gx-Auto, ST72216Gx-Auto, ST72254Gx-Auto
16-BIT TIMER (Cont’d)
CONTROL REGISTER 2 (CR2)
Read/Write
Reset Value: 0000 0000 (00h)
7
0
OC1E OC2E OPM PWM CC1 CC0 IEDG2 EXEDG
Bit 7 = OC1E Output Compare 1 Pin Enable.
This bit is used only to output the signal from the
timer on the OCMP1 pin (OLV1 in Output Compare mode, both OLV1 and OLV2 in PWM and
one-pulse mode). Whatever the value of the OC1E
bit, the internal Output Compare 1 function of the
timer remains active.
0: OCMP1 pin alternate function disabled (I/O pin
free for general-purpose I/O).
1: OCMP1 pin alternate function enabled.
Bit 6 = OC2E Output Compare 2 Pin Enable.
This bit is used only to output the signal from the
timer on the OCMP2 pin (OLV2 in Output Compare mode). Whatever the value of the OC2E bit,
the internal Output Compare 2 function of the timer
remains active.
0: OCMP2 pin alternate function disabled (I/O pin
free for general-purpose I/O).
1: OCMP2 pin alternate function enabled.
Bit 5 = OPM One Pulse mode.
0: One Pulse mode is not active.
1: One Pulse mode is active, the ICAP1 pin can be
used to trigger one pulse on the OCMP1 pin; the
active transition is given by the IEDG1 bit. The
length of the generated pulse depends on the
contents of the OC1R register.
56/135
Bit 4 = PWM Pulse Width Modulation.
0: PWM mode is not active.
1: PWM mode is active, the OCMP1 pin outputs a
programmable cyclic signal; the length of the
pulse depends on the value of OC1R register;
the period depends on the value of OC2R register.
Bits 3:2 = CC[1:0] Clock Control.
The timer clock mode depends on these bits:
Table 13. Clock Control Bits
Timer Clock
fCPU / 4
fCPU / 2
fCPU / 8
External Clock (where
available)
CC1
0
0
1
CC0
0
1
0
1
1
Note: If the external clock pin is not available, programming the external clock configuration stops
the counter.
Bit 1 = IEDG2 Input Edge 2.
This bit determines which type of level transition
on the ICAP2 pin will trigger the capture.
0: A falling edge triggers the capture.
1: A rising edge triggers the capture.
Bit 0 = EXEDG External Clock Edge.
This bit determines which type of level transition
on the external clock pin (EXTCLK) will trigger the
counter register.
0: A falling edge triggers the counter register.
1: A rising edge triggers the counter register.
ST72104Gx-Auto, ST72215Gx-Auto, ST72216Gx-Auto, ST72254Gx-Auto
16-BIT TIMER (Cont’d)
STATUS REGISTER (SR)
Read Only
Reset Value: 0000 0000 (00h)
The three least significant bits are not used.
7
ICF1
0
OCF1
TOF
ICF2
OCF2
0
0
0
Bit 7 = ICF1 Input Capture Flag 1.
0: No input capture (reset value).
1: An input capture has occurred on the ICAP1 pin
or the counter has reached the OC2R value in
PWM mode. To clear this bit, first read the SR
register, then read or write the low byte of the
IC1R (IC1LR) register.
Bit 6 = OCF1 Output Compare Flag 1.
0: No match (reset value).
1: The content of the free running counter matches
the content of the OC1R register. To clear this
bit, first read the SR register, then read or write
the low byte of the OC1R (OC1LR) register.
Bit 5 = TOF Timer Overflow Flag.
0: No timer overflow (reset value).
1: The free running counter has rolled over from
FFFFh to 0000h. To clear this bit, first read the
SR register, then read or write the low byte of
the CR (CLR) register.
Note: Reading or writing the ACLR register does
not clear TOF.
Bit 4 = ICF2 Input Capture Flag 2.
0: No input capture (reset value).
1: An input capture has occurred on the ICAP2
pin. To clear this bit, first read the SR register,
then read or write the low byte of the IC2R
(IC2LR) register.
Bit 3 = OCF2 Output Compare Flag 2.
0: No match (reset value).
1: The content of the free running counter matches
the content of the OC2R register. To clear this
bit, first read the SR register, then read or write
the low byte of the OC2R (OC2LR) register.
INPUT CAPTURE 1 HIGH REGISTER (IC1HR)
Read Only
Reset Value: Undefined
This is an 8-bit read only register that contains the
high part of the counter value (transferred by the
input capture 1 event).
7
0
MSB
LSB
INPUT CAPTURE 1 LOW REGISTER (IC1LR)
Read Only
Reset Value: Undefined
This is an 8-bit read only register that contains the
low part of the counter value (transferred by the input capture 1 event).
7
0
MSB
LSB
OUTPUT COMPARE 1 HIGH REGISTER
(OC1HR)
Read/Write
Reset Value: 1000 0000 (80h)
This is an 8-bit register that contains the high part
of the value to be compared to the CHR register.
7
0
MSB
LSB
OUTPUT COMPARE 1 LOW REGISTER
(OC1LR)
Read/Write
Reset Value: 0000 0000 (00h)
This is an 8-bit register that contains the low part of
the value to be compared to the CLR register.
7
0
MSB
LSB
Bit 2:0 = Reserved, forced by hardware to 0.
57/135
ST72104Gx-Auto, ST72215Gx-Auto, ST72216Gx-Auto, ST72254Gx-Auto
16-BIT TIMER (Cont’d)
OUTPUT COMPARE 2 HIGH REGISTER
(OC2HR)
Read/Write
Reset Value: 1000 0000 (80h)
This is an 8-bit register that contains the high part
of the value to be compared to the CHR register.
ALTERNATE COUNTER HIGH REGISTER
(ACHR)
Read Only
Reset Value: 1111 1111 (FFh)
This is an 8-bit register that contains the high part
of the counter value.
7
0
7
0
MSB
LSB
MSB
LSB
OUTPUT COMPARE 2 LOW REGISTER
(OC2LR)
Read/Write
Reset Value: 0000 0000 (00h)
This is an 8-bit register that contains the low part of
the value to be compared to the CLR register.
7
0
MSB
LSB
COUNTER HIGH REGISTER (CHR)
Read Only
Reset Value: 1111 1111 (FFh)
This is an 8-bit register that contains the high part
of the counter value.
7
0
MSB
LSB
COUNTER LOW REGISTER (CLR)
Read Only
Reset Value: 1111 1100 (FCh)
This is an 8-bit register that contains the low part of
the counter value. A write to this register resets the
counter. An access to this register after accessing
the SR register clears the TOF bit.
7
0
MSB
LSB
58/135
ALTERNATE COUNTER LOW REGISTER
(ACLR)
Read Only
Reset Value: 1111 1100 (FCh)
This is an 8-bit register that contains the low part of
the counter value. A write to this register resets the
counter. An access to this register after an access
to SR register does not clear the TOF bit in SR
register.
7
0
MSB
LSB
INPUT CAPTURE 2 HIGH REGISTER (IC2HR)
Read Only
Reset Value: Undefined
This is an 8-bit read only register that contains the
high part of the counter value (transferred by the
Input Capture 2 event).
7
0
MSB
LSB
INPUT CAPTURE 2 LOW REGISTER (IC2LR)
Read Only
Reset Value: Undefined
This is an 8-bit read only register that contains the
low part of the counter value (transferred by the Input Capture 2 event).
7
0
MSB
LSB
ST72104Gx-Auto, ST72215Gx-Auto, ST72216Gx-Auto, ST72254Gx-Auto
16-BIT TIMER (Cont’d)
Table 14. 16-Bit Timer Register Map and Reset Values
Address
(Hex.)
Register
Label
Timer A: 32 CR1
Timer B: 42 Reset Value
Timer A: 31 CR2
Timer B: 41 Reset Value
Timer A: 33 SR
Timer B: 43 Reset Value
Timer A: 34 ICHR1
Timer B: 44 Reset Value
Timer A: 35 ICLR1
Timer B: 45 Reset Value
Timer A: 36 OCHR1
Timer B: 46 Reset Value
Timer A: 37 OCLR1
Timer B: 47 Reset Value
Timer A: 3E OCHR2
Timer B: 4E Reset Value
Timer A: 3F OCLR2
Timer B: 4F Reset Value
Timer A: 38 CHR
Timer B: 48 Reset Value
Timer A: 39 CLR
Timer B: 49 Reset Value
Timer A: 3A ACHR
Timer B: 4A Reset Value
Timer A: 3B ACLR
Timer B: 4B Reset Value
Timer A: 3C ICHR2
Timer B: 4C Reset Value
Timer A: 3D ICLR2
Timer B: 4D Reset Value
7
6
5
4
3
2
1
0
ICIE
OCIE
TOIE
FOLV2
FOLV1
OLVL2
IEDG1
OLVL1
0
0
0
0
0
0
0
0
OC1E
OC2E
OPM
PWM
CC1
CC0
IEDG2
EXEDG
0
0
0
0
0
0
0
0
ICF1
OCF1
TOF
ICF2
OCF2
-
-
-
0
0
0
0
0
0
0
0
MSB
-
-
-
-
-
-
-
LSB
-
MSB
-
-
-
-
-
-
-
LSB
-
MSB
-
-
-
-
-
-
-
LSB
-
MSB
-
-
-
-
-
-
-
LSB
-
MSB
-
-
-
-
-
-
-
LSB
-
MSB
-
-
-
-
-
-
-
LSB
-
MSB
1
1
1
1
1
1
1
LSB
1
MSB
1
1
1
1
1
1
0
LSB
0
MSB
1
1
1
1
1
1
1
LSB
1
MSB
1
1
1
1
1
1
0
LSB
0
MSB
-
-
-
-
-
-
-
LSB
-
MSB
-
-
-
-
-
-
-
LSB
-
59/135
ST72104Gx-Auto, ST72215Gx-Auto, ST72216Gx-Auto, ST72254Gx-Auto
11.3 SERIAL PERIPHERAL INTERFACE (SPI)
11.3.1 Introduction
The Serial Peripheral Interface (SPI) allows fullduplex, synchronous, serial communication with
external devices. An SPI system may consist of a
master and one or more slaves or a system in
which devices may be either masters or slaves.
The SPI is normally used for communication between the microcontroller and external peripherals
or another microcontroller.
Refer to the Pin Description chapter for the devicespecific pinout.
11.3.2 Main Features
■ Full duplex, three-wire synchronous transfers
■ Master or slave operation
■ 4 master mode frequencies
■ Maximum slave mode frequency = fCPU/4
■ 4 programmable master bit rates
■ Programmable clock polarity and phase
■ End of transfer interrupt flag
■ Write collision flag protection
■ Master mode fault protection capability
11.3.3 General description
The SPI is connected to external devices through
four alternate pins:
– MISO: Master In Slave Out pin
– MOSI: Master Out Slave In pin
– SCK: Serial Clock pin
– SS: Slave select pin
A basic example of interconnections between a
single master and a single slave is illustrated on
Figure 36.
The MOSI pins are connected together as are
MISO pins. In this way data is transferred serially
between master and slave (most significant bit
first).
When the master device transmits data to a slave
device via MOSI pin, the slave device responds by
sending data to the master device via the MISO
pin. This implies full duplex transmission with both
data out and data in synchronized with the same
clock signal (which is provided by the master device via the SCK pin).
Thus, the byte transmitted is replaced by the byte
received and eliminates the need for separate
transmit-empty and receiver-full bits. A status flag
is used to indicate that the I/O operation is complete.
Four possible data/clock timing relationships may
be chosen (see Figure 39) but master and slave
must be programmed with the same timing mode.
Figure 36. Serial Peripheral Interface Master/Slave
SLAVE
MASTER
MSBit
LSBit
8-BIT SHIFT REGISTER
SPI
CLOCK
GENERATOR
60/135
MSBit
MISO
MISO
MOSI
MOSI
SCK
SS
SCK
+5V
SS
LSBit
8-BIT SHIFT REGISTER
ST72104Gx-Auto, ST72215Gx-Auto, ST72216Gx-Auto, ST72254Gx-Auto
SERIAL PERIPHERAL INTERFACE (Cont’d)
Figure 37. Serial Peripheral Interface Block Diagram
Internal Bus
Read
DR
IT
Read Buffer
request
MOSI
MISO
SR
8-Bit Shift Register
SPIF WCOL
-
MODF
-
-
-
-
Write
SPI
STATE
CONTROL
SCK
SS
CR
SPIE
SPE
SPR2 MSTR CPOL CPHA SPR1 SPR0
MASTER
CONTROL
SERIAL
CLOCK
GENERATOR
61/135
ST72104Gx-Auto, ST72215Gx-Auto, ST72216Gx-Auto, ST72254Gx-Auto
SERIAL PERIPHERAL INTERFACE (Cont’d)
11.3.4 Functional Description
Figure 36 shows the serial peripheral interface
(SPI) block diagram.
This interface contains three dedicated registers:
– A Control Register (CR)
– A Status Register (SR)
– A Data Register (DR)
Refer to the CR, SR and DR registers in Section
11.3.7 for the bit definitions.
11.3.4.1 Master Configuration
In a master configuration, the serial clock is generated on the SCK pin.
Procedure
– Select the SPR0 and SPR1 bits to define the
serial clock baud rate (see CR register).
– Select the CPOL and CPHA bits to define one
of the four relationships between the data
transfer and the serial clock (see Figure 39).
– The SS pin must be connected to a high level
signal during the complete byte transmit sequence.
– The MSTR and SPE bits must be set (they remain set only if the SS pin is connected to a
high level signal).
In this configuration the MOSI pin is a data output
and to the MISO pin is a data input.
62/135
Transmit sequence
The transmit sequence begins when a byte is written the DR register.
The data byte is parallel loaded into the 8-bit shift
register (from the internal bus) during a write cycle
and then shifted out serially to the MOSI pin most
significant bit first.
When data transfer is complete:
– The SPIF bit is set by hardware
– An interrupt is generated if the SPIE bit is set
and the I bit in the CCR register is cleared.
During the last clock cycle the SPIF bit is set, a
copy of the data byte received in the shift register
is moved to a buffer. When the DR register is read,
the SPI peripheral returns this buffered value.
Clearing the SPIF bit is performed by the following
software sequence:
1. An access to the SR register while the SPIF bit
is set
2. A read to the DR register.
Note: While the SPIF bit is set, all writes to the DR
register are inhibited until the SR register is read.
ST72104Gx-Auto, ST72215Gx-Auto, ST72216Gx-Auto, ST72254Gx-Auto
SERIAL PERIPHERAL INTERFACE (Cont’d)
11.3.4.2 Slave Configuration
In slave configuration, the serial clock is received
on the SCK pin from the master device.
The value of the SPR0 & SPR1 bits is not used for
the data transfer.
Procedure
– For correct data transfer, the slave device
must be in the same timing mode as the master device (CPOL and CPHA bits). See Figure
39.
– The SS pin must be connected to a low level
signal during the complete byte transmit sequence.
– Clear the MSTR bit and set the SPE bit to assign the pins to alternate function.
In this configuration the MOSI pin is a data input
and the MISO pin is a data output.
Transmit Sequence
The data byte is parallel loaded into the 8-bit shift
register (from the internal bus) during a write cycle
and then shifted out serially to the MISO pin most
significant bit first.
The transmit sequence begins when the slave device receives the clock signal and the most significant bit of the data on its MOSI pin.
When data transfer is complete:
– The SPIF bit is set by hardware
– An interrupt is generated if SPIE bit is set and
I bit in CCR register is cleared.
During the last clock cycle the SPIF bit is set, a
copy of the data byte received in the shift register
is moved to a buffer. When the DR register is read,
the SPI peripheral returns this buffered value.
Clearing the SPIF bit is performed by the following
software sequence:
1. An access to the SR register while the SPIF bit
is set.
2. A read to the DR register.
Notes: While the SPIF bit is set, all writes to the
DR register are inhibited until the SR register is
read.
The SPIF bit can be cleared during a second
transmission; however, it must be cleared before
the second SPIF bit in order to prevent an overrun
condition (see Section 11.3.4.6).
Depending on the CPHA bit, the SS pin has to be
set to write to the DR register between each data
byte transfer to avoid a write collision (see Section
11.3.4.4).
63/135
ST72104Gx-Auto, ST72215Gx-Auto, ST72216Gx-Auto, ST72254Gx-Auto
SERIAL PERIPHERAL INTERFACE (Cont’d)
11.3.4.3 Data Transfer Format
During an SPI transfer, data is simultaneously
transmitted (shifted out serially) and received
(shifted in serially). The serial clock is used to synchronize the data transfer during a sequence of
eight clock pulses.
The SS pin allows individual selection of a slave
device; the other slave devices that are not selected do not interfere with the SPI transfer.
Clock Phase and Clock Polarity
Four possible timing relationships may be chosen
by software, using the CPOL and CPHA bits.
The CPOL (clock polarity) bit controls the steady
state value of the clock when no data is being
transferred. This bit affects both master and slave
modes.
The combination between the CPOL and CPHA
(clock phase) bits selects the data capture clock
edge.
Figure 39, shows an SPI transfer with the four
combinations of the CPHA and CPOL bits. The diagram may be interpreted as a master or slave
timing diagram where the SCK pin, the MISO pin,
the MOSI pin are directly connected between the
master and the slave device.
The SS pin is the slave device select input and can
be driven by the master device.
The master device applies data to its MOSI pinclock edge before the capture clock edge.
CPHA bit is set
The second edge on the SCK pin (falling edge if
the CPOL bit is reset, rising edge if the CPOL bit is
set) is the MSBit capture strobe. Data is latched on
the occurrence of the second clock transition.
No write collision should occur even if the SS pin
stays low during a transfer of several bytes (see
Figure 38).
CPHA bit is reset
The first edge on the SCK pin (falling edge if CPOL
bit is set, rising edge if CPOL bit is reset) is the
MSBit capture strobe. Data is latched on the occurrence of the first clock transition.
The SS pin must be toggled high and low between
each byte transmitted (see Figure 38).
To protect the transmission from a write collision a
low value on the SS pin of a slave device freezes
the data in its DR register and does not allow it to
be altered. Therefore the SS pin must be high to
write a new data byte in the DR without producing
a write collision.
Figure 38. CPHA / SS Timing Diagram
MOSI/MISO
Byte 1
Byte 2
Byte 3
Master SS
Slave SS
(CPHA=0)
Slave SS
(CPHA=1)
VR02131A
64/135
ST72104Gx-Auto, ST72215Gx-Auto, ST72216Gx-Auto, ST72254Gx-Auto
SERIAL PERIPHERAL INTERFACE (Cont’d)
Figure 39. Data Clock Timing Diagram
CPHA =1
SCLK (with
CPOL = 1)
SCLK (with
CPOL = 0)
MISO
(from master)
MOSI
(from slave)
MSBit
Bit 6
Bit 5
Bit 4
Bit3
Bit 2
Bit 1
LSBit
MSBit
Bit 6
Bit 5
Bit 4
Bit3
Bit 2
Bit 1
LSBit
SS
(to slave)
CAPTURE STROBE
CPHA =0
CPOL = 1
CPOL = 0
MSBit
MISO
(from master)
MOSI
(from slave)
MSBit
Bit 6
Bit 5
Bit 4
Bit3
Bit 2
Bit 1
LSBit
Bit 6
Bit 5
Bit 4
Bit3
Bit 2
Bit 1
LSBit
SS
(to slave)
CAPTURE STROBE
Note: This figure should not be used as a replacement for parametric information.
Refer to the Electrical Characteristics chapter.
VR02131B
65/135
ST72104Gx-Auto, ST72215Gx-Auto, ST72216Gx-Auto, ST72254Gx-Auto
SERIAL PERIPHERAL INTERFACE (Cont’d)
11.3.4.4 Write Collision Error
A write collision occurs when the software tries to
write to the DR register while a data transfer is taking place with an external device. When this happens, the transfer continues uninterrupted; and
the software write will be unsuccessful.
Write collisions can occur both in master and slave
mode.
Note: A “read collision” will never occur since the
received data byte is placed in a buffer in which
access is always synchronous with the MCU operation.
In Slave mode
When the CPHA bit is set:
The slave device will receive a clock (SCK) edge
prior to the latch of the first data transfer. This first
clock edge will freeze the data in the slave device
DR register and output the MSBit on to the external MISO pin of the slave device.
The SS pin low state enables the slave device but
the output of the MSBit onto the MISO pin does
not take place until the first data transfer clock
edge.
When the CPHA bit is reset:
Data is latched on the occurrence of the first clock
transition. The slave device does not have any
way of knowing when that transition will occur;
therefore, the slave device collision occurs when
software attempts to write the DR register after its
SS pin has been pulled low.
For this reason, the SS pin must be high, between
each data byte transfer, to allow the CPU to write
in the DR register without generating a write collision.
In Master mode
Collision in the master device is defined as a write
of the DR register while the internal serial clock
(SCK) is in the process of transfer.
The SS pin signal must be always high on the
master device.
WCOL bit
The WCOL bit in the SR register is set if a write
collision occurs.
No SPI interrupt is generated when the WCOL bit
is set (the WCOL bit is a status flag only).
Clearing the WCOL bit is done through a software
sequence (see Figure 40).
Figure 40. Clearing the WCOL bit (Write Collision Flag) Software Sequence
Clearing sequence after SPIF = 1 (end of a data byte transfer)
1st Step
Read SR
OR
Read SR
THEN
THEN
2nd Step
Read DR
SPIF =0
WCOL=0
Write DR
SPIF =0
WCOL=0 if no transfer has started
WCOL=1 if a transfer has started
before the 2nd step
Clearing sequence before SPIF = 1 (during a data byte transfer)
1st Step
Read SR
THEN
2nd Step
66/135
Read DR
WCOL=0
Note: Writing to the DR register
instead of reading in it does not
reset the WCOL bit.
ST72104Gx-Auto, ST72215Gx-Auto, ST72216Gx-Auto, ST72254Gx-Auto
SERIAL PERIPHERAL INTERFACE (Cont’d)
11.3.4.5 Master Mode Fault
Master mode fault occurs when the master device
has its SS pin pulled low, then the MODF bit is set.
Master mode fault affects the SPI peripheral in the
following ways:
– The MODF bit is set and an SPI interrupt is
generated if the SPIE bit is set.
– The SPE bit is reset. This blocks all output
from the device and disables the SPI peripheral.
– The MSTR bit is reset, thus forcing the device
into slave mode.
Clearing the MODF bit is done through a software
sequence:
1. A read or write access to the SR register while
the MODF bit is set.
2. A write to the CR register.
Notes: To avoid any multiple slave conflicts in the
case of a system comprising several MCUs, the
SS pin must be pulled high during the clearing sequence of the MODF bit. The SPE and MSTR bits
may be restored to their original state during or after this clearing sequence.
Hardware does not allow the user to set the SPE
and MSTR bits while the MODF bit is set except in
the MODF bit clearing sequence.
In a slave device the MODF bit cannot be set, but
in a multi master configuration the device can be in
slave mode with this MODF bit set.
The MODF bit indicates that there might have
been a multimaster conflict for system control and
allows a proper exit from system operation to a reset or default system state using an interrupt routine.
11.3.4.6 Overrun Condition
An overrun condition occurs when the master device has sent several data bytes and the slave device has not cleared the SPIF bit issuing from the
previous data byte transmitted.
In this case, the receiver buffer contains the byte
sent after the SPIF bit was last cleared. A read to
the DR register returns this byte. All other bytes
are lost.
This condition is not detected by the SPI peripheral.
67/135
ST72104Gx-Auto, ST72215Gx-Auto, ST72216Gx-Auto, ST72254Gx-Auto
SERIAL PERIPHERAL INTERFACE (Cont’d)
11.3.4.7 Single Master and Multimaster Configurations
There are two types of SPI systems:
For more security, the slave device may respond
to the master with the received data byte. Then the
– Single Master System
master will receive the previous byte back from the
– Multimaster System
slave device if all MISO and MOSI pins are connected and the slave has not written its DR regisSingle Master System
ter.
A typical single master system may be configured,
Other transmission security methods can use
using an MCU as the master and four MCUs as
ports for handshake lines or data bytes with comslaves (see Figure 41).
mand fields.
The master device selects the individual slave deMultimaster System
vices by using four pins of a parallel port to control
the four SS pins of the slave devices.
A multimaster system may also be configured by
the user. Transfer of master control could be imThe SS pins are pulled high during reset since the
plemented using a handshake method through the
master device ports will be forced to be inputs at
I/O ports or by an exchange of code messages
that time, thus disabling the slave devices.
through the serial peripheral interface system.
Note: To prevent a bus conflict on the MISO line
The multi-master system is principally handled by
the master allows only one active slave device
the MSTR bit in the CR register and the MODF bit
during a transmission.
in the SR register.
Figure 41. Single Master Configuration
SS
SCK
Slave
MCU
Slave
MCU
MOSI MISO
MOSI MISO
SCK
Master
MCU
5V
68/135
SS
Ports
MOSI MISO
SS
SS
SCK
SS
SCK
Slave
MCU
SCK
Slave
MCU
MOSI MISO
MOSI MISO
ST72104Gx-Auto, ST72215Gx-Auto, ST72216Gx-Auto, ST72254Gx-Auto
SERIAL PERIPHERAL INTERFACE (Cont’d)
11.3.5 Low Power Modes
Mode
WAIT
HALT
Description
No effect on SPI.
SPI interrupt events cause the device to exit from WAIT mode.
SPI registers are frozen.
In HALT mode, the SPI is inactive. SPI operation resumes when the MCU is woken up by an interrupt with
“exit from HALT mode” capability.
11.3.6 Interrupts
Interrupt Event
SPI End of Transfer Event
Master Mode Fault Event
Event
Flag
Enable
Control
Bit
SPIF
MODF
SPIE
Exit
from
Wait
Yes
Yes
Exit
from
Halt
No
No
Note: The SPI interrupt events are connected to
the same interrupt vector (see Interrupts chapter).
They generate an interrupt if the corresponding
Enable Control Bit is set and the interrupt mask in
the CC register is reset (RIM instruction).
69/135
ST72104Gx-Auto, ST72215Gx-Auto, ST72216Gx-Auto, ST72254Gx-Auto
SERIAL PERIPHERAL INTERFACE (Cont’d)
11.3.7 Register Description
CONTROL REGISTER (CR)
Read/Write
Reset Value: 0000xxxx (0xh)
7
0
SPIE SPE SPR2 MSTR CPOL CPHA SPR1 SPR0
Bit 7 = SPIE Serial peripheral interrupt enable.
This bit is set and cleared by software.
0: Interrupt is inhibited
1: An SPI interrupt is generated whenever SPIF=1
or MODF=1 in the SR register
Bit 6 = SPE Serial peripheral output enable.
This bit is set and cleared by software. It is also
cleared by hardware when, in master mode, SS=0
(see Section 11.3.4.5 "Master Mode Fault" on
page 67).
0: I/O port connected to pins
1: SPI alternate functions connected to pins
The SPE bit is cleared by reset, so the SPI peripheral is not initially connected to the external pins.
Bit 3 = CPOL Clock polarity.
This bit is set and cleared by software. This bit determines the steady state of the serial Clock. The
CPOL bit affects both the master and slave
modes.
0: The steady state is a low value at the SCK pin.
1: The steady state is a high value at the SCK pin.
Bit 2 = CPHA Clock phase.
This bit is set and cleared by software.
0: The first clock transition is the first data capture
edge.
1: The second clock transition is the first capture
edge.
Bit 1:0 = SPR[1:0] Serial peripheral rate.
These bits are set and cleared by software.Used
with the SPR2 bit, they select one of six baud rates
to be used as the serial clock when the device is a
master.
These 2 bits have no effect in slave mode.
Table 15. Serial Peripheral Baud Rate
Bit 5 = SPR2 Divider Enable.
this bit is set and cleared by software and it is
cleared by reset. It is used with the SPR[1:0] bits to
set the baud rate. Refer to Table 15.
0: Divider by 2 enabled
1: Divider by 2 disabled
Bit 4 = MSTR Master.
This bit is set and cleared by software. It is also
cleared by hardware when, in master mode, SS=0
(see Section 11.3.4.5 "Master Mode Fault" on
page 67).
0: Slave mode is selected
1: Master mode is selected, the function of the
SCK pin changes from an input to an output and
the functions of the MISO and MOSI pins are reversed.
70/135
Serial Clock
SPR2
SPR1
SPR0
fCPU/4
1
0
0
fCPU/8
0
0
0
fCPU/16
0
0
1
fCPU/32
1
1
0
fCPU/64
0
1
0
fCPU/128
0
1
1
ST72104Gx-Auto, ST72215Gx-Auto, ST72216Gx-Auto, ST72254Gx-Auto
SERIAL PERIPHERAL INTERFACE (Cont’d)
STATUS REGISTER (SR)
Read Only
Reset Value: 0000 0000 (00h)
7
SPIF
WCOL
-
MODF
-
-
-
DATA I/O REGISTER (DR)
Read/Write
Reset Value: Undefined
0
7
-
D7
Bit 7 = SPIF Serial Peripheral data transfer flag.
This bit is set by hardware when a transfer has
been completed. An interrupt is generated if
SPIE=1 in the CR register. It is cleared by a software sequence (an access to the SR register followed by a read or write to the DR register).
0: Data transfer is in progress or has been approved by a clearing sequence.
1: Data transfer between the device and an external device has been completed.
Note: While the SPIF bit is set, all writes to the DR
register are inhibited.
Bit 6 = WCOL Write Collision status.
This bit is set by hardware when a write to the DR
register is done during a transmit sequence. It is
cleared by a software sequence (see Figure 40).
0: No write collision occurred
1: A write collision has been detected
0
D6
D5
D4
D3
D2
D1
D0
The DR register is used to transmit and receive
data on the serial bus. In the master device only a
write to this register will initiate transmission/reception of another byte.
Notes: During the last clock cycle the SPIF bit is
set, a copy of the received data byte in the shift
register is moved to a buffer. When the user reads
the serial peripheral data I/O register, the buffer is
actually being read.
Warning:
A write to the DR register places data directly into
the shift register for transmission.
A read to the DR register returns the value located
in the buffer and not the contents of the shift register (See Figure 37).
Bit 5 = Unused.
Bit 4 = MODF Mode Fault flag.
This bit is set by hardware when the SS pin is
pulled low in master mode (see Section 11.3.4.5
"Master Mode Fault" on page 67). An SPI interrupt
can be generated if SPIE=1 in the CR register.
This bit is cleared by a software sequence (An access to the SR register while MODF=1 followed by
a write to the CR register).
0: No master mode fault detected
1: A fault in master mode has been detected
Bits 3:0 = Unused.
71/135
ST72104Gx-Auto, ST72215Gx-Auto, ST72216Gx-Auto, ST72254Gx-Auto
SERIAL PERIPHERAL INTERFACE (Cont’d)
Table 16. SPI Register Map and Reset Values
Address
(Hex.)
Register
Label
7
6
5
4
3
2
1
0
0021h
SPIDR
Reset Value
MSB
x
x
x
x
x
x
x
LSB
x
0022h
SPICR
Reset Value
SPIE
0
SPE
0
SPR2
0
MSTR
0
CPOL
x
CPHA
x
SPR1
x
SPR0
x
0023h
SPISR
Reset Value
SPIF
0
WCOL
0
0
MODF
0
0
0
0
0
72/135
ST72104Gx-Auto, ST72215Gx-Auto, ST72216Gx-Auto, ST72254Gx-Auto
11.4 I2C BUS INTERFACE (I2C)
11.4.1 Introduction
The I2C Bus Interface serves as an interface between the microcontroller and the serial I2C bus. It
provides both multimaster and slave functions,
and controls all I2C bus-specific sequencing, protocol, arbitration and timing. It supports fast I2C
mode (400 kHz).
11.4.2 Main Features
2
■ Parallel-bus/I C protocol converter
■ Multi-master capability
■ 7-bit/10-bit Addressing
■ Transmitter/Receiver flag
■ End-of-byte transmission flag
■ Transfer problem detection
I2C Master Features
■ Clock generation
2
■ I C bus busy flag
■ Arbitration Lost Flag
■ End of byte transmission flag
■ Transmitter/Receiver Flag
■ Start bit detection flag
■ Start and Stop generation
I2C Slave Features
■ Stop bit detection
2
■ I C bus busy flag
■ Detection of misplaced start or stop condition
2
■ Programmable I C Address detection
■ Transfer problem detection
■ End-of-byte transmission flag
■ Transmitter/Receiver flag
11.4.3 General Description
In addition to receiving and transmitting data, this
interface converts it from serial to parallel format
and vice versa, using either an interrupt or polled
handshake. The interrupts are enabled or disabled
by software. The interface is connected to the I2C
bus by a data pin (SDAI) and by a clock pin (SCLI).
It can be connected both with a standard I2C bus
and a Fast I2C bus. This selection is made by software.
Mode Selection
The interface can operate in the four following
modes:
– Slave transmitter/receiver
– Master transmitter/receiver
By default, it operates in slave mode.
The interface automatically switches from slave to
master after it generates a START condition and
from master to slave in case of arbitration loss or a
STOP generation, allowing then Multi-Master capability.
Communication Flow
In Master mode, it initiates a data transfer and
generates the clock signal. A serial data transfer
always begins with a start condition and ends with
a stop condition. Both start and stop conditions are
generated in master mode by software.
In Slave mode, the interface is capable of recognising its own address (7 or 10-bit), and the General Call address. The General Call address detection may be enabled or disabled by software.
Data and addresses are transferred as 8-bit bytes,
MSB first. The first byte(s) following the start condition contain the address (one in 7-bit mode, two
in 10-bit mode). The address is always transmitted
in Master mode.
A 9th clock pulse follows the 8 clock cycles of a
byte transfer, during which the receiver must send
an acknowledge bit to the transmitter. Refer to Figure 42.
Figure 42. I2C BUS Protocol
SDA
ACK
MSB
SCL
1
START
CONDITION
2
8
9
STOP
CONDITION
VR02119B
73/135
ST72104Gx-Auto, ST72215Gx-Auto, ST72216Gx-Auto, ST72254Gx-Auto
I2C BUS INTERFACE (Cont’d)
Acknowledge may be enabled and disabled by
software.
The I2C interface address and/or general call address can be selected by software.
The speed of the I2C interface may be selected
between Standard (up to 100 kHz) and Fast I2C
(up to 400 kHz).
SDA/SCL Line Control
Transmitter mode: the interface holds the clock
line low before transmission to wait for the microcontroller to write the byte in the Data Register.
Receiver mode: the interface holds the clock line
low after reception to wait for the microcontroller to
read the byte in the Data Register.
The SCL frequency (fSCL) is controlled by a programmable clock divider which depends on the
I2C bus mode.
When the I2C cell is enabled, the SDA and SCL
ports must be configured as floating inputs. In this
case, the value of the external pull-up resistor
used depends on the application.
When the I2C cell is disabled, the SDA and SCL
ports revert to being standard I / O port pins.
Figure 43. I2C Interface Block Diagram
DATA REGISTER (DR)
SDA or SDAI
DATA CONTROL
DATA SHIFT REGISTER
COMPARATOR
OWN ADDRESS REGISTER 1 (OAR1)
OWN ADDRESS REGISTER 2 (OAR2)
SCL or SCLI
CLOCK CONTROL
CLOCK CONTROL REGISTER (CCR)
CONTROL REGISTER (CR)
STATUS REGISTER 1 (SR1)
CONTROL LOGIC
STATUS REGISTER 2 (SR2)
INTERRUPT
74/135
ST72104Gx-Auto, ST72215Gx-Auto, ST72216Gx-Auto, ST72254Gx-Auto
I2C BUS INTERFACE (Cont’d)
11.4.4 Functional Description
Refer to the CR, SR1 and SR2 registers in Section
11.4.7. for the bit definitions.
By default the I2C interface operates in Slave
mode (M/SL bit is cleared) except when it initiates
a transmit or receive sequence.
First the interface frequency must be configured
using the FRi bits in the OAR2 register.
11.4.4.1 Slave Mode
As soon as a start condition is detected, the
address is received from the SDA line and sent to
the shift register; then it is compared with the
address of the interface or the General Call
address (if selected by software).
Note: In 10-bit addressing mode, the comparison
includes the header sequence (11110xx0) and the
two most significant bits of the address.
Header matched (10-bit mode only): the interface
generates an acknowledge pulse if the ACK bit is
set.
Address not matched: the interface ignores it
and waits for another Start condition.
Address matched: the interface generates in sequence:
– Acknowledge pulse if the ACK bit is set.
– EVF and ADSL bits are set with an interrupt if the
ITE bit is set.
Then the interface waits for a read of the SR1 register, holding the SCL line low (see Figure 44
Transfer sequencing EV1).
Next, in 7-bit mode read the DR register to determine from the least significant bit (Data Direction
Bit) if the slave must enter Receiver or Transmitter
mode.
In 10-bit mode, after receiving the address sequence the slave is always in receive mode. It will
enter transmit mode on receiving a repeated Start
condition followed by the header sequence with
matching address bits and the least significant bit
set (11110xx1).
Slave Receiver
Following the address reception and after SR1
register has been read, the slave receives bytes
from the SDA line into the DR register via the internal shift register. After each byte the interface generates in sequence:
– Acknowledge pulse if the ACK bit is set
– EVF and BTF bits are set with an interrupt if the
ITE bit is set.
Then the interface waits for a read of the SR1 register followed by a read of the DR register, holding
the SCL line low (see Figure 44 Transfer sequencing EV2).
Slave Transmitter
Following the address reception and after SR1
register has been read, the slave sends bytes from
the DR register to the SDA line via the internal shift
register.
The slave waits for a read of the SR1 register followed by a write in the DR register, holding the
SCL line low (see Figure 44 Transfer sequencing
EV3).
When the acknowledge pulse is received:
– The EVF and BTF bits are set by hardware with
an interrupt if the ITE bit is set.
Closing slave communication
After the last data byte is transferred a Stop Condition is generated by the master. The interface
detects this condition and sets:
– EVF and STOPF bits with an interrupt if the ITE
bit is set.
Then the interface waits for a read of the SR2 register (see Figure 44 Transfer sequencing EV4).
Error Cases
– BERR: Detection of a Stop or a Start condition
during a byte transfer. In this case, the EVF and
the BERR bits are set with an interrupt if the ITE
bit is set.
If it is a Stop then the interface discards the data,
released the lines and waits for another Start
condition.
If it is a Start then the interface discards the data
and waits for the next slave address on the bus.
– AF: Detection of a non-acknowledge bit. In this
case, the EVF and AF bits are set with an interrupt if the ITE bit is set.
The AF bit is cleared by reading the I2CSR2 register. However, if read before the completion of
the transmission, the AF flag will be set again,
thus possibly generating a new interrupt. Software must ensure either that the SCL line is back
at 0 before reading the SR2 register, or be able
to correctly handle a second interrupt during the
9th pulse of a transmitted byte.
Note: In both cases, SCL line is not held low; however, the SDA line can remain low if the last bits
transmitted are all 0. It is then necessary to release both lines by software. The SCL line is not
held low while AF = 1 but by other flags (SB or
BTF) that are set at the same time.
75/135
ST72104Gx-Auto, ST72215Gx-Auto, ST72216Gx-Auto, ST72254Gx-Auto
I2C BUS INTERFACE (Cont’d)
How to release the SDA / SCL lines
Set and subsequently clear the STOP bit while
BTF is set. The SDA/SCL lines are released after
the transfer of the current byte.
SMBus Compatibility
ST7 I2C is compatible with SMBus V1.1 protocol. It
supports all SMBus addressing modes, SMBus
bus protocols and CRC-8 packet error checking.
Refer to AN1713: SMBus Slave Driver For ST7
I2C Peripheral.
11.4.4.2 Master Mode
To switch from default Slave mode to Master
mode a Start condition generation is needed.
Start condition
Setting the START bit while the BUSY bit is
cleared causes the interface to switch to Master
mode (M/SL bit set) and generates a Start condition.
Once the Start condition is sent:
– The EVF and SB bits are set by hardware with
an interrupt if the ITE bit is set.
Then the master waits for a read of the SR1 register followed by a write in the DR register with the
Slave address, holding the SCL line low (see
Figure 44 Transfer sequencing EV5).
Slave address transmission
Then the slave address is sent to the SDA line via
the internal shift register.
In 7-bit addressing mode, one address byte is
sent.
In 10-bit addressing mode, sending the first byte
including the header sequence causes the following event:
– The EVF bit is set by hardware with interrupt
generation if the ITE bit is set.
Then the master waits for a read of the SR1 register followed by a write in the DR register, holding
the SCL line low (see Figure 44 Transfer sequencing EV9).
76/135
Then the second address byte is sent by the interface.
After completion of this transfer (and acknowledge
from the slave if the ACK bit is set):
– The EVF bit is set by hardware with interrupt
generation if the ITE bit is set.
Then the master waits for a read of the SR1 register followed by a write in the CR register (for example set PE bit), holding the SCL line low (see Figure 44 Transfer sequencing EV6).
Next the master must enter Receiver or Transmitter mode.
Note: In 10-bit addressing mode, to switch the
master to Receiver mode, software must generate
a repeated Start condition and resend the header
sequence with the least significant bit set
(11110xx1).
Master Receiver
Following the address transmission and after SR1
and CR registers have been accessed, the master
receives bytes from the SDA line into the DR register via the internal shift register. After each byte
the interface generates in sequence:
– Acknowledge pulse if the ACK bit is set
– EVF and BTF bits are set by hardware with an interrupt if the ITE bit is set.
Then the interface waits for a read of the SR1 register followed by a read of the DR register, holding
the SCL line low (see Figure 44 Transfer sequencing EV7).
To close the communication: before reading the
last byte from the DR register, set the STOP bit to
generate the Stop condition. The interface goes
automatically back to slave mode (M/SL bit
cleared).
Note: In order to generate the non-acknowledge
pulse after the last received data byte, the ACK bit
must be cleared just before reading the second
last data byte.
ST72104Gx-Auto, ST72215Gx-Auto, ST72216Gx-Auto, ST72254Gx-Auto
I2C BUS INTERFACE (Cont’d)
Master Transmitter
Following the address transmission and after SR1
register has been read, the master sends bytes
from the DR register to the SDA line via the internal shift register.
The master waits for a read of the SR1 register followed by a write in the DR register, holding the
SCL line low (see Figure 44 Transfer sequencing
EV8).
When the acknowledge bit is received, the
interface sets:
– EVF and BTF bits with an interrupt if the ITE bit
is set.
To close the communication: after writing the last
byte to the DR register, set the STOP bit to generate the Stop condition. The interface goes automatically back to slave mode (M/SL bit cleared).
Error Cases
– BERR: Detection of a Stop or a Start condition
during a byte transfer. In this case, the EVF and
BERR bits are set by hardware with an interrupt
if ITE is set.
Note that BERR will not be set if an error is detected during the first pulse of each 9-bit transaction:
Single Master Mode
If a Start or Stop is issued during the first pulse of
a 9-bit transaction, the BERR flag will not be set
and transfer will continue however the BUSY flag
will be reset. To work around this, slave devices
should issue a NACK when they receive a misplaced Start or Stop. The reception of a NACK or
BUSY by the master in the middle of communication gives the possibility to reinitiate transmis-
sion.
Multimaster Mode
Normally the BERR bit would be set whenever
unauthorized transmission takes place while
transfer is already in progress. However, an issue will arise if an external master generates an
unauthorized Start or Stop while the I2C master
is on the first pulse of a 9-bit transaction. It is possible to work around this by polling the BUSY bit
during I2C master mode transmission. The resetting of the BUSY bit can then be handled in a
similar manner as the BERR flag being set.
– AF: Detection of a non-acknowledge bit. In this
case, the EVF and AF bits are set by hardware
with an interrupt if the ITE bit is set. To resume,
set the Start or Stop bit.
The AF bit is cleared by reading the I2CSR2 register. However, if read before the completion of
the transmission, the AF flag will be set again,
thus possibly generating a new interrupt. Software must ensure either that the SCL line is back
at 0 before reading the SR2 register, or be able
to correctly handle a second interrupt during the
9th pulse of a transmitted byte.
– ARLO: Detection of an arbitration lost condition.
In this case the ARLO bit is set by hardware (with
an interrupt if the ITE bit is set and the interface
goes automatically back to slave mode (the M/SL
bit is cleared).
Note: In all these cases, the SCL line is not held
low; however, the SDA line can remain low if the
last bits transmitted are all 0. It is then necessary
to release both lines by software. The SCL line is
not held low while AF = 1 but by other flags (SB or
BTF) that are set at the same time.
77/135
ST72104Gx-Auto, ST72215Gx-Auto, ST72216Gx-Auto, ST72254Gx-Auto
I2C BUS INTERFACE (Cont’d)
Figure 44. Transfer Sequencing
7-bit Slave receiver:
S Address
A
Data1
A
Data2
EV1
A
EV2
EV2
.....
DataN
A
P
EV2
EV4
7-bit Slave transmitter:
S Address
A
Data1
A
EV1 EV3
Data2
A
EV3
EV3
.....
DataN
NA
P
EV3-1
EV4
7-bit Master receiver:
S
Address
A
EV5
Data1
A
EV6
Data2
A
EV7
EV7
DataN
.....
NA
P
EV7
7-bit Master transmitter:
S
Address
A
EV5
Data1
A
EV6 EV8
Data2
A
EV8
EV8
DataN
.....
A
P
EV8
10-bit Slave receiver:
S Header
A
Address
A
Data1
A
EV1
.....
EV2
DataN
A
P
EV2
EV4
10-bit Slave transmitter:
Sr Header A
Data1
A
EV1 EV3
.... DataN
EV3 .
A
P
EV3-1
EV4
10-bit Master transmitter
S
Header
EV5
A
Address
EV9
A
Data1
A
EV6 EV8
EV8
DataN
.....
A
P
EV8
10-bit Master receiver:
Sr
Header
EV5
A
Data1
EV6
A
EV7
.....
DataN
A
P
EV7
Legend: S=Start, Sr = Repeated Start, P=Stop, A=Acknowledge, NA=Non-acknowledge,
EVx=Event (with interrupt if ITE=1)
EV1: EVF=1, ADSL=1, cleared by reading SR1 register.
EV2: EVF=1, BTF=1, cleared by reading SR1 register followed by reading DR register.
EV3: EVF=1, BTF=1, cleared by reading SR1 register followed by writing DR register.
EV3-1: EVF=1, AF=1, BTF=1; AF is cleared by reading SR1 register. BTF is cleared by releasing the
lines (STOP=1, STOP=0) or by writing DR register (DR=FFh). Note: If lines are released by
STOP=1, STOP=0, the subsequent EV4 is not seen.
EV4: EVF=1, STOPF=1, cleared by reading SR2 register.
EV5: EVF=1, SB=1, cleared by reading SR1 register followed by writing DR register.
EV6: EVF=1, cleared by reading SR1 register followed by writing CR register (for example PE=1).
EV7: EVF=1, BTF=1, cleared by reading SR1 register followed by reading DR register.
EV8: EVF=1, BTF=1, cleared by reading SR1 register followed by writing DR register.
EV9: EVF=1, ADD10=1, cleared by reading SR1 register followed by writing DR register.
78/135
ST72104Gx-Auto, ST72215Gx-Auto, ST72216Gx-Auto, ST72254Gx-Auto
I2C BUS INTERFACE (Cont’d)
11.4.5 Low Power Modes
Mode
WAIT
HALT
Description
No effect on I2C interface.
I2C interrupts cause the device to exit from WAIT mode.
I2C registers are frozen.
In HALT mode, the I2C interface is inactive and does not acknowledge data on the bus. The I2C interface
resumes operation when the MCU is woken up by an interrupt with “exit from HALT mode” capability.
11.4.6 Interrupts
Figure 45. Event Flags and Interrupt Generation
ADD10
BTF
ADSL
SB
AF
STOPF
ARLO
BERR
ITE
INTERRUPT
EVF
*
* EVF can also be set by EV6 or an error from the SR2 register.
Interrupt Event
10-bit Address Sent Event (Master mode)
End of Byte Transfer Event
Address Matched Event (Slave mode)
Start Bit Generation Event (Master mode)
Acknowledge Failure Event
Stop Detection Event (Slave mode)
Arbitration Lost Event (Multimaster configuration)
Bus Error Event
Event
Flag
Enable
Control
Bit
ADD10
BTF
ADSL
SB
AF
STOPF
ARLO
BERR
ITE
Exit
from
Wait
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Exit
from
Halt
No
No
No
No
No
No
No
No
Note: The I2C interrupt events are connected to
the same interrupt vector (see Interrupts chapter).
They generate an interrupt if the corresponding
Enable Control Bit is set and the I-bit in the CC register is reset (RIM instruction).
79/135
ST72104Gx-Auto, ST72215Gx-Auto, ST72216Gx-Auto, ST72254Gx-Auto
I2C BUS INTERFACE (Cont’d)
11.4.7 Register Description
I2C CONTROL REGISTER (CR)
Read / Write
Reset Value: 0000 0000 (00h)
7
0
– In slave mode:
0: No start generation
1: Start generation when the bus is free
0
0
PE
ENGC START ACK STOP ITE
Bit 2 = ACK Acknowledge enable.
This bit is set and cleared by software. It is also
cleared by hardware when the interface is disabled (PE=0).
0: No acknowledge returned
1: Acknowledge returned after an address byte or
a data byte is received
Bit 7:6 = Reserved. Forced to 0 by hardware.
Bit 5 = PE Peripheral enable.
This bit is set and cleared by software.
0: Peripheral disabled
1: Master/Slave capability
Notes:
– When PE=0, all the bits of the CR register and
the SR register except the Stop bit are reset. All
outputs are released while PE=0
– When PE=1, the corresponding I/O pins are selected by hardware as alternate functions.
– To enable the I2C interface, write the CR register
TWICE with PE=1 as the first write only activates
the interface (only PE is set).
Bit 4 = ENGC Enable General Call.
This bit is set and cleared by software. It is also
cleared by hardware when the interface is disabled (PE=0). The 00h General Call address is acknowledged (01h ignored).
0: General Call disabled
1: General Call enabled
Note: In accordance with the I2C standard, when
GCAL addressing is enabled, an I2C slave can
only receive data. It will not transmit data to the
master.
Bit 3 = START Generation of a Start condition.
This bit is set and cleared by software. It is also
cleared by hardware when the interface is disabled (PE=0) or when the Start condition is sent
(with interrupt generation if ITE=1).
– In master mode:
0: No start generation
1: Repeated start generation
80/135
Bit 1 = STOP Generation of a Stop condition.
This bit is set and cleared by software. It is also
cleared by hardware in master mode.
Note: This bit is not cleared when the interface is
disabled (PE=0).
– In master mode:
0: No stop generation
1: Stop generation after the current byte transfer
or after the current Start condition is sent. The
STOP bit is cleared by hardware when the Stop
condition is sent.
– In slave mode:
0: No stop generation
1: Release the SCL and SDA lines after the current byte transfer (BTF=1). In this mode the
STOP bit has to be cleared by software.
Bit 0 = ITE Interrupt enable.
This bit is set and cleared by software and cleared
by hardware when the interface is disabled
(PE=0).
0: Interrupts disabled
1: Interrupts enabled
Refer to Figure 45 for the relationship between the
events and the interrupt.
SCL is held low when the ADD10, SB, BTF or
ADSL flags or an EV6 event (See Figure 44) is detected.
ST72104Gx-Auto, ST72215Gx-Auto, ST72216Gx-Auto, ST72254Gx-Auto
I2C BUS INTERFACE (Cont’d)
I2C STATUS REGISTER 1 (SR1)
Read Only
Reset Value: 0000 0000 (00h)
7
EVF ADD10 TRA BUSY BTF ADSL M/SL
0
SB
Bit 7 = EVF Event flag.
This bit is set by hardware as soon as an event occurs. It is cleared by software reading SR2 register
in case of error event or as described in Figure 44.
It is also cleared by hardware when the interface is
disabled (PE=0).
0: No event
1: One of the following events has occurred:
– BTF=1 (Byte received or transmitted)
– ADSL=1 (Address matched in Slave mode
while ACK=1)
– SB=1 (Start condition generated in Master
mode)
– AF=1 (No acknowledge received after byte
transmission)
– STOPF=1 (Stop condition detected in Slave
mode)
– ARLO=1 (Arbitration lost in Master mode)
– BERR=1 (Bus error, misplaced Start or Stop
condition detected)
– ADD10=1 (Master has sent header byte)
– Address byte successfully transmitted in Master mode.
Bit 6 = ADD10 10-bit addressing in Master mode.
This bit is set by hardware when the master has
sent the first byte in 10-bit address mode. It is
cleared by software reading SR2 register followed
by a write in the DR register of the second address
byte. It is also cleared by hardware when the peripheral is disabled (PE=0).
0: No ADD10 event occurred.
1: Master has sent first address byte (header)
Bit 5 = TRA Transmitter/Receiver.
When BTF is set, TRA=1 if a data byte has been
transmitted. It is cleared automatically when BTF
is cleared. It is also cleared by hardware after de-
tection of Stop condition (STOPF=1), loss of bus
arbitration (ARLO=1) or when the interface is disabled (PE=0).
0: Data byte received (if BTF=1)
1: Data byte transmitted
Bit 4 = BUSY Bus busy.
This bit is set by hardware on detection of a Start
condition and cleared by hardware on detection of
a Stop condition. It indicates a communication in
progress on the bus. The BUSY flag of the I2CSR1
register is cleared if a Bus Error occurs.
0: No communication on the bus
1: Communication ongoing on the bus
Bit 3 = BTF Byte transfer finished.
This bit is set by hardware as soon as a byte is correctly received or transmitted with interrupt generation if ITE=1. It is cleared by software reading
SR1 register followed by a read or write of DR register. It is also cleared by hardware when the interface is disabled (PE=0).
– Following a byte transmission, this bit is set after
reception of the acknowledge clock pulse. In
case an address byte is sent, this bit is set only
after the EV6 event (See Figure 44). BTF is
cleared by reading SR1 register followed by writing the next byte in DR register.
– Following a byte reception, this bit is set after
transmission of the acknowledge clock pulse if
ACK=1. BTF is cleared by reading SR1 register
followed by reading the byte from DR register.
The SCL line is held low while BTF=1.
0: Byte transfer not done
1: Byte transfer succeeded
Bit 2 = ADSL Address matched (Slave mode).
This bit is set by hardware as soon as the received
slave address matched with the OAR register content or a general call is recognized. An interrupt is
generated if ITE=1. It is cleared by software reading SR1 register or by hardware when the interface is disabled (PE=0).
The SCL line is held low while ADSL=1.
0: Address mismatched or not received
1: Received address matched
81/135
ST72104Gx-Auto, ST72215Gx-Auto, ST72216Gx-Auto, ST72254Gx-Auto
I2C BUS INTERFACE (Cont’d)
Bit 1 = M/SL Master/Slave.
This bit is set by hardware as soon as the interface
is in Master mode (writing START=1). It is cleared
by hardware after detecting a Stop condition on
the bus or a loss of arbitration (ARLO=1). It is also
cleared when the interface is disabled (PE=0).
0: Slave mode
1: Master mode
Bit 0 = SB Start bit (Master mode).
This bit is set by hardware as soon as the Start
condition is generated (following a write
START=1). An interrupt is generated if ITE=1. It is
cleared by software reading SR1 register followed
by writing the address byte in DR register. It is also
cleared by hardware when the interface is disabled (PE=0).
0: No Start condition
1: Start condition generated
I2C STATUS REGISTER 2 (SR2)
Read Only
Reset Value: 0000 0000 (00h)
7
0
0
0
0
AF
STOPF ARLO BERR GCAL
Bit 7:5 = Reserved. Forced to 0 by hardware.
Bit 4 = AF Acknowledge failure.
This bit is set by hardware when no acknowledge
is returned. An interrupt is generated if ITE=1. It is
cleared by software reading SR2 register or by
hardware when the interface is disabled (PE=0).
The SCL line is not held low while AF=1 but by other flags (SB or BTF) that are set at the same time.
0: No acknowledge failure
1: Acknowledge failure
Bit 3 = STOPF Stop detection (Slave mode).
This bit is set by hardware when a Stop condition
is detected on the bus after an acknowledge (if
ACK=1). An interrupt is generated if ITE=1. It is
cleared by software reading SR2 register or by
hardware when the interface is disabled (PE=0).
The SCL line is not held low while STOPF=1.
0: No Stop condition detected
1: Stop condition detected
82/135
Bit 2 = ARLO Arbitration lost.
This bit is set by hardware when the interface loses the arbitration of the bus to another master. An
interrupt is generated if ITE=1. It is cleared by software reading SR2 register or by hardware when
the interface is disabled (PE=0).
After an ARLO event the interface switches back
automatically to Slave mode (M/SL=0).
The SCL line is not held low while ARLO=1.
0: No arbitration lost detected
1: Arbitration lost detected
Note:
– In a Multimaster environment, when the interface
is configured in Master Receive mode it does not
perform arbitration during the reception of the
Acknowledge Bit. Mishandling of the ARLO bit
from the I2CSR2 register may occur when a second master simultaneously requests the same
data from the same slave and the I2C master
does not acknowledge the data. The ARLO bit is
then left at 0 instead of being set.
Bit 1 = BERR Bus error.
This bit is set by hardware when the interface detects a misplaced Start or Stop condition. An interrupt is generated if ITE=1. It is cleared by software
reading SR2 register or by hardware when the interface is disabled (PE=0).
The SCL line is not held low while BERR=1.
0: No misplaced Start or Stop condition
1: Misplaced Start or Stop condition
Note:
– If a Bus Error occurs, a Stop or a repeated Start
condition should be generated by the Master to
re-synchronize communication, get the transmission acknowledged and the bus released for further communication
Bit 0 = GCAL General Call (Slave mode).
This bit is set by hardware when a general call address is detected on the bus while ENGC=1. It is
cleared by hardware detecting a Stop condition
(STOPF=1) or when the interface is disabled
(PE=0).
0: No general call address detected on bus
1: general call address detected on bus
ST72104Gx-Auto, ST72215Gx-Auto, ST72216Gx-Auto, ST72254Gx-Auto
I2C BUS INTERFACE (Cont’d)
I2C CLOCK CONTROL REGISTER (CCR)
Read / Write
Reset Value: 0000 0000 (00h)
7
I2C OWN ADDRESS REGISTER (OAR1)
Read / Write
Reset Value: 0000 0000 (00h)
0
FM/SM CC6
CC5
CC4
CC3
CC2
CC1
CC0
Bit 7 = FM/SM Fast/Standard I2C mode.
This bit is set and cleared by software. It is not
cleared when the interface is disabled (PE=0).
0: Standard I2C mode
1: Fast I2C mode
Bit 6:0 = CC[6:0] 7-bit clock divider.
These bits select the speed of the bus (fSCL) depending on the I2C mode. They are not cleared
when the interface is disabled (PE=0).
Refer to the Electrical Characteristics section for
the table of values.
Note: The programmed fSCL assumes no load on
SCL and SDA lines.
I2C DATA REGISTER (DR)
Read / Write
Reset Value: 0000 0000 (00h)
7
D7
0
D6
D5
D4
D3
D2
D1
D0
Bit 7:0 = D[7:0] 8-bit Data Register.
These bits contain the byte to be received or transmitted on the bus.
– Transmitter mode: Byte transmission start automatically when the software writes in the DR register.
– Receiver mode: the first data byte is received automatically in the DR register using the least significant bit of the address.
Then, the following data bytes are received one
by one after reading the DR register.
7
0
ADD7 ADD6 ADD5 ADD4 ADD3 ADD2 ADD1 ADD0
7-bit Addressing Mode
Bit 7:1 = ADD[7:1] Interface address.
These bits define the I2C bus address of the interface. They are not cleared when the interface is
disabled (PE=0).
Bit 0 = ADD0 Address direction bit.
This bit is don’t care, the interface acknowledges
either 0 or 1. It is not cleared when the interface is
disabled (PE=0).
Note: Address 01h is always ignored.
10-bit Addressing Mode
Bit 7:0 = ADD[7:0] Interface address.
These are the least significant bits of the I2C bus
address of the interface. They are not cleared
when the interface is disabled (PE=0).
I2C OWN ADDRESS REGISTER (OAR2)
Read / Write
Reset Value: 0100 0000 (40h)
7
FR1
0
FR0
0
0
0
ADD9 ADD8
0
Bit 7:6 = FR[1:0] Frequency bits.
These bits are set by software only when the interface is disabled (PE=0). To configure the interface
to I2C specified delays select the value corresponding to the microcontroller frequency fCPU.
fCPU
< 6 MHz
6 to 8 MHz
FR1
0
0
FR0
0
1
Bit 5:3 = Reserved
Bit 2:1 = ADD[9:8] Interface address.
These are the most significant bits of the I2C bus
address of the interface (10-bit mode only). They
are not cleared when the interface is disabled
(PE=0).
Bit 0 = Reserved.
83/135
ST72104Gx-Auto, ST72215Gx-Auto, ST72216Gx-Auto, ST72254Gx-Auto
Table 17. I2C Register Map and Reset Values
Address
(Hex.)
Register
Label
0028h
7
6
5
4
3
2
1
0
I2CCR
Reset Value
0
0
PE
0
ENGC
0
START
0
ACK
0
STOP
0
ITE
0
0029h
I2CSR1
Reset Value
EVF
0
ADD10
0
TRA
0
BUSY
0
BTF
0
ADSL
0
M/SL
0
SB
0
002Ah
I2CSR2
Reset Value
0
0
0
AF
0
STOPF
0
ARLO
0
BERR
0
GCAL
0
02Bh
I2CCCR
Reset Value
FM/SM
0
CC6
0
CC5
0
CC4
0
CC3
0
CC2
0
CC1
0
CC0
0
02Ch
I2COAR1
Reset Value
ADD7
0
ADD6
0
ADD5
0
ADD4
0
ADD3
0
ADD2
0
ADD1
0
ADD0
0
002Dh
I2COAR2
Reset Value
FR1
0
FR0
1
0
0
0
ADD9
0
ADD8
0
0
002Eh
I2CDR
Reset Value
MSB
0
0
0
0
0
0
0
LSB
0
84/135
ST72104Gx-Auto, ST72215Gx-Auto, ST72216Gx-Auto, ST72254Gx-Auto
11.5 8-BIT A/D CONVERTER (ADC)
11.5.1 Introduction
The on-chip Analog to Digital Converter (ADC) peripheral is an 8-bit, successive approximation converter with internal sample and hold circuitry. This
peripheral has up to 16 multiplexed analog input
channels (refer to device pinout description) that
allow the peripheral to convert the analog voltage
levels from up to 16 different sources.
The result of the conversion is stored in an 8-bit
Data Register. The A/D converter is controlled
through a Control/Status Register.
11.5.3 Functional Description
11.5.3.1 Analog Power Supply
VDDA and VSSA are the high and low level reference voltage pins. In some devices (refer to device
pinout description) they are internally connected to
the VDD and VSS pins.
Conversion accuracy may therefore be impacted
by voltage drops and noise in the event of heavily
loaded or badly decoupled power supply lines.
See electrical characteristics section for more details.
11.5.2 Main Features
■ 8-bit conversion
■ Up to 16 channels with multiplexed input
■ Linear successive approximation
■ Data register (DR) which contains the results
■ Conversion complete status flag
■ On/off bit (to reduce consumption)
The block diagram is shown in Figure 46.
Figure 46. ADC Block Diagram
fCPU
COCO
0
ADON
0
fADC
DIV 2
CH3 CH2
CH1 CH0
ADCCSR
4
AIN0
HOLD CONTROL
RADC
AIN1
ANALOG TO DIGITAL
ANALOG
MUX
CONVERTER
AINx
CADC
ADCDR
D7
D6
D5
D4
D3
D2
D1
D0
85/135
ST72104Gx-Auto, ST72215Gx-Auto, ST72216Gx-Auto, ST72254Gx-Auto
8-BIT A/D CONVERTER (ADC) (Cont’d)
11.5.3.2 Digital A/D Conversion Result
The conversion is monotonic, meaning that the result never decreases if the analog input does not
and never increases if the analog input does not.
If the input voltage (VAIN) is greater than or equal
to VDDA (high-level voltage reference) then the
conversion result in the DR register is FFh (full
scale) without overflow indication.
If input voltage (VAIN) is lower than or equal to
VSSA (low-level voltage reference) then the conversion result in the DR register is 00h.
The A/D converter is linear and the digital result of
the conversion is stored in the ADCDR register.
The accuracy of the conversion is described in the
parametric section.
RAIN is the maximum recommended impedance
for an analog input signal. If the impedance is too
high, this will result in a loss of accuracy due to
leakage and sampling not being completed in the
allotted time.
11.5.3.3 A/D Conversion Phases
The A/D conversion is based on two conversion
phases as shown in Figure 47:
■ Sample capacitor loading [duration: tLOAD]
During this phase, the VAIN input voltage to be
measured is loaded into the CADC sample
capacitor.
■ A/D conversion [duration: tCONV]
During this phase, the A/D conversion is
computed (8 successive approximations cycles)
and the CADC sample capacitor is disconnected
from the analog input pin to get the optimum
analog to digital conversion accuracy.
While the ADC is on, these two phases are continuously repeated.
At the end of each conversion, the sample capacitor is kept loaded with the previous measurement
load. The advantage of this behavior is that it minimizes the current consumption on the analog pin
in case of single input channel measurement.
11.5.3.4 Software Procedure
Refer to the control/status register (CSR) and data
register (DR) in Section 11.5.6 for the bit definitions and to Figure 47 for the timings.
ADC Configuration
The total duration of the A/D conversion is 12 ADC
clock periods (1/fADC=2/fCPU).
86/135
The analog input ports must be configured as input, no pull-up, no interrupt. Refer to the “I/O ports”
chapter. Using these pins as analog inputs does
not affect the ability of the port to be read as a logic
input.
In the CSR register:
– Select the CH[3:0] bits to assign the analog
channel to be converted.
ADC Conversion
In the CSR register:
– Set the ADON bit to enable the A/D converter
and to start the first conversion. From this time
on, the ADC performs a continuous conversion of the selected channel.
When a conversion is complete
– The COCO bit is set by hardware.
– No interrupt is generated.
– The result is in the DR register and remains
valid until the next conversion has ended.
A write to the CSR register (with ADON set) aborts
the current conversion, resets the COCO bit and
starts a new conversion.
Figure 47. ADC Conversion Timings
ADON
ADCCSR WRITE
OPERATION
tCONV
HOLD
CONTROL
tLOAD
COCO BIT SET
11.5.4 Low Power Modes
Mode
WAIT
HALT
Description
No effect on A/D Converter
A/D Converter disabled.
After wake-up from Halt mode, the A/D Converter requires a stabilization time before accurate conversions can be performed.
Note: The A/D converter may be disabled by resetting the ADON bit. This feature allows reduced
power consumption when no conversion is needed
and between single shot conversions.
11.5.5 Interrupts
None
ST72104Gx-Auto, ST72215Gx-Auto, ST72216Gx-Auto, ST72254Gx-Auto
8-BIT A/D CONVERTER (ADC) (Cont’d)
11.5.6 Register Description
CONTROL/STATUS REGISTER (CSR)
Read / Write
Reset Value: 0000 0000 (00h)
DATA REGISTER (DR)
Read Only
Reset Value: 0000 0000 (00h)
7
COCO
0
ADON
0
CH3
CH2
CH1
0
7
CH0
D7
Bit 7 = COCO Conversion Complete
This bit is set by hardware. It is cleared by software reading the result in the DR register or writing
to the CSR register.
0: Conversion is not complete
1: Conversion can be read from the DR register
0
D6
D5
D4
D3
D2
D1
D0
Bits 7:0 = D[7:0] Analog Converted Value
This register contains the converted analog value
in the range 00h to FFh.
Note: Reading this register reset the COCO flag.
Bit 6 = Reserved. must always be cleared.
Bit 5 = ADON A/D Converter On
This bit is set and cleared by software.
0: A/D converter is switched off
1: A/D converter is switched on
Bit 4 = Reserved. must always be cleared.
Bits 3:0 = CH[3:0] Channel Selection
These bits are set and cleared by software. They
select the analog input to convert.
Channel Pin*
CH3
CH2
CH1
CH0
AIN0
AIN1
AIN2
AIN3
AIN4
AIN5
AIN6
AIN7
AIN8
AIN9
AIN10
AIN11
AIN12
AIN13
AIN14
AIN15
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
*Note: The number of pins AND the channel selection varies according to the device. Refer to the device pinout.
87/135
ST72104Gx-Auto, ST72215Gx-Auto, ST72216Gx-Auto, ST72254Gx-Auto
8-BIT A/D CONVERTER (ADC) (Cont’d)
Table 18. ADC Register Map and Reset Values
Address
(Hex.)
Register
Label
7
6
5
4
3
2
1
0
0070h
ADCDR
Reset Value
D7
0
D6
0
D5
0
D4
0
D3
0
D2
0
D1
0
D0
0
0071h
ADCCSR
Reset Value
COCO
0
0
ADON
0
0
CH3
0
CH2
0
CH1
0
CH0
0
88/135
ST72104Gx-Auto, ST72215Gx-Auto, ST72216Gx-Auto, ST72254Gx-Auto
12 INSTRUCTION SET
12.1 ST7 ADDRESSING MODES
The ST7 Core features 17 different addressing
modes which can be classified in 7 main groups:
Addressing Mode
Example
Inherent
nop
Immediate
ld A,#$55
Direct
ld A,$55
Indexed
ld A,($55,X)
Indirect
ld A,([$55],X)
Relative
jrne loop
Bit operation
bset
byte,#5
The ST7 Instruction set is designed to minimize
the number of bytes required per instruction: To do
so, most of the addressing modes may be subdivided in two submodes called long and short:
– Long addressing mode is more powerful because it can use the full 64 Kbyte address space,
however it uses more bytes and more CPU cycles.
– Short addressing mode is less powerful because
it can generally only access page zero (0000h 00FFh range), but the instruction size is more
compact, and faster. All memory to memory instructions use short addressing modes only
(CLR, CPL, NEG, BSET, BRES, BTJT, BTJF,
INC, DEC, RLC, RRC, SLL, SRL, SRA, SWAP)
The ST7 Assembler optimizes the use of long and
short addressing modes.
Table 19. ST7 Addressing Mode Overview
Mode
Syntax
Destination/
Source
Pointer
Address
(Hex.)
Pointer
Size
(Hex.)
Length
(bytes)
Inherent
nop
+0
Immediate
ld A,#$55
+1
Short
Direct
ld A,$10
00..FF
+1
Long
Direct
ld A,$1000
0000..FFFF
+2
No Offset
Direct
Indexed
ld A,(X)
00..FF
+ 0 (with X register)
+ 1 (with Y register)
Short
Direct
Indexed
ld A,($10,X)
00..1FE
+1
Long
Direct
Indexed
ld A,($1000,X)
0000..FFFF
Short
Indirect
ld A,[$10]
00..FF
00..FF
byte
+2
Long
Indirect
ld A,[$10.w]
0000..FFFF
00..FF
word
+2
Short
Indirect
Indexed
ld A,([$10],X)
00..1FE
00..FF
byte
+2
Long
Indirect
Indexed
ld A,([$10.w],X)
0000..FFFF
00..FF
word
+2
00..FF
byte
00..FF
byte
Relative
Direct
jrne loop
PC-128/PC+1271)
Relative
Indirect
jrne [$10]
PC-128/PC+1271)
Bit
Direct
bset $10,#7
00..FF
Bit
Indirect
bset [$10],#7
00..FF
Bit
Direct
Relative
btjt $10,#7,skip
00..FF
Bit
Indirect
Relative
btjt [$10],#7,skip 00..FF
+2
+1
+2
+1
+2
+2
00..FF
byte
+3
Notes:
1. At the time the instruction is executed, the Program Counter (PC) points to the instruction following JRxx.
89/135
ST72104Gx-Auto, ST72215Gx-Auto, ST72216Gx-Auto, ST72254Gx-Auto
ST7 ADDRESSING MODES (Cont’d)
12.1.1 Inherent
All Inherent instructions consist of a single byte.
The opcode fully specifies all the required information for the CPU to process the operation.
Inherent Instruction
Function
NOP
No operation
TRAP
S/W Interrupt
WFI
Wait For Interrupt (Low Power
Mode)
HALT
Halt Oscillator (Lowest Power
Mode)
RET
Sub-routine Return
IRET
Interrupt Sub-routine Return
SIM
Set Interrupt Mask
RIM
Reset Interrupt Mask
SCF
Set Carry Flag
RCF
Reset Carry Flag
RSP
Reset Stack Pointer
LD
Load
CLR
Clear
PUSH/POP
Push/Pop to/from the stack
INC/DEC
Increment/Decrement
TNZ
Test Negative or Zero
CPL, NEG
1 or 2 Complement
MUL
Byte Multiplication
SLL, SRL, SRA, RLC,
RRC
Shift and Rotate Operations
SWAP
Swap Nibbles
12.1.2 Immediate
Immediate instructions have two bytes, the first
byte contains the opcode, the second byte contains the operand value.
Immediate Instruction
Function
LD
Load
CP
Compare
BCP
Bit Compare
AND, OR, XOR
Logical Operations
ADC, ADD, SUB, SBC
Arithmetic Operations
90/135
12.1.3 Direct
In Direct instructions, the operands are referenced
by their memory address.
The direct addressing mode consists of two submodes:
Direct (short)
The address is a byte, thus requires only one byte
after the opcode, but only allows 00 - FF addressing space.
Direct (long)
The address is a word, thus allowing 64 Kbyte addressing space, but requires 2 bytes after the opcode.
12.1.4 Indexed (No Offset, Short, Long)
In this mode, the operand is referenced by its
memory address, which is defined by the unsigned
addition of an index register (X or Y) with an offset.
The indexed addressing mode consists of three
submodes:
Indexed (No Offset)
There is no offset, (no extra byte after the opcode),
and allows 00 - FF addressing space.
Indexed (Short)
The offset is a byte, thus requires only one byte after the opcode and allows 00 - 1FE addressing
space.
Indexed (long)
The offset is a word, thus allowing 64 Kbyte addressing space and requires 2 bytes after the opcode.
12.1.5 Indirect (Short, Long)
The required data byte to do the operation is found
by its memory address, located in memory (pointer).
The pointer address follows the opcode. The indirect addressing mode consists of two submodes:
Indirect (short)
The pointer address is a byte, the pointer size is a
byte, thus allowing 00 - FF addressing space, and
requires 1 byte after the opcode.
Indirect (long)
The pointer address is a byte, the pointer size is a
word, thus allowing 64 Kbyte addressing space,
and requires 1 byte after the opcode.
ST72104Gx-Auto, ST72215Gx-Auto, ST72216Gx-Auto, ST72254Gx-Auto
ST7 ADDRESSING MODES (Cont’d)
12.1.6 Indirect Indexed (Short, Long)
This is a combination of indirect and short indexed
addressing modes. The operand is referenced by
its memory address, which is defined by the unsigned addition of an index register value (X or Y)
with a pointer value located in memory. The pointer address follows the opcode.
The indirect indexed addressing mode consists of
two submodes:
Indirect Indexed (Short)
The pointer address is a byte, the pointer size is a
byte, thus allowing 00 - 1FE addressing space,
and requires 1 byte after the opcode.
Indirect Indexed (Long)
The pointer address is a byte, the pointer size is a
word, thus allowing 64 Kbyte addressing space,
and requires 1 byte after the opcode.
12.1.7 Relative Mode (Direct, Indirect)
This addressing mode is used to modify the PC
register value by adding an 8-bit signed offset to it.
Available Relative Direct/
Indirect Instructions
Function
JRxx
Conditional Jump
CALLR
Call Relative
The relative addressing mode consists of two submodes:
Relative (Direct)
The offset follows the opcode.
Relative (Indirect)
The offset is defined in memory, of which the address follows the opcode.
Table 20. Instructions Supporting Direct,
Indexed, Indirect and Indirect Indexed
Addressing Modes
Long and Short
Instructions
Function
LD
Load
CP
Compare
AND, OR, XOR
Logical Operations
ADC, ADD, SUB, SBC
Arithmetic Addition/subtraction operations
BCP
Bit Compare
Short Instructions Only
Function
CLR
Clear
INC, DEC
Increment/Decrement
TNZ
Test Negative or Zero
CPL, NEG
1 or 2 Complement
BSET, BRES
Bit Operations
BTJT, BTJF
Bit Test and Jump Operations
SLL, SRL, SRA, RLC,
RRC
Shift and Rotate Operations
SWAP
Swap Nibbles
CALL, JP
Call or Jump subroutine
91/135
ST72104Gx-Auto, ST72215Gx-Auto, ST72216Gx-Auto, ST72254Gx-Auto
12.2 INSTRUCTION GROUPS
The ST 7 family devices use an Instruction Set
consisting of 63 instructions. The instructions may
be subdivided into 13 main groups as illustrated in
the following table:
Load and Transfer
LD
CLR
Stack operation
PUSH
POP
Increment/Decrement
INC
DEC
Compare and Tests
CP
TNZ
BCP
Logical operations
AND
OR
XOR
CPL
NEG
Bit Operation
BSET
BRES
Conditional Bit Test and Branch
BTJT
BTJF
Arithmetic operations
ADC
ADD
SUB
SBC
MUL
Shift and Rotates
SLL
SRL
SRA
RLC
RRC
SWAP
SLA
Unconditional Jump or Call
JRA
JRT
JRF
JP
CALL
CALLR
NOP
Conditional Branch
JRxx
Interruption management
TRAP
WFI
HALT
IRET
Condition Code Flag modification
SIM
RIM
SCF
RCF
Using a prebyte
The instructions are described with one to four
bytes.
In order to extend the number of available opcodes for an 8-bit CPU (256 opcodes), three different prebyte opcodes are defined. These prebytes
modify the meaning of the instruction they precede.
The whole instruction becomes:
PC-2 End of previous instruction
PC-1 Prebyte
PC
Opcode
PC+1 Additional word (0 to 2) according to the
number of bytes required to compute the
effective address
92/135
RSP
RET
These prebytes enable instruction in Y as well as
indirect addressing modes to be implemented.
They precede the opcode of the instruction in X or
the instruction using direct addressing mode. The
prebytes are:
PDY 90 Replace an X based instruction using
immediate, direct, indexed, or inherent
addressing mode by a Y one.
PIX 92 Replace an instruction using direct, direct bit, or direct relative addressing
mode to an instruction using the corresponding indirect addressing mode.
It also changes an instruction using X
indexed addressing mode to an instruction using indirect X indexed addressing
mode.
PIY 91 Replace an instruction using X indirect
indexed addressing mode by a Y one.
ST72104Gx-Auto, ST72215Gx-Auto, ST72216Gx-Auto, ST72254Gx-Auto
INSTRUCTION GROUPS (Cont’d)
Mnemo
Description
Function/Example
Dst
Src
H
I
N
Z
C
ADC
Add with Carry
A=A+M+C
A
M
H
N
Z
C
ADD
Addition
A=A+M
A
M
H
N
Z
C
AND
Logical And
A=A.M
A
M
N
Z
BCP
Bit compare A, Memory
tst (A . M)
A
M
N
Z
BRES
Bit Reset
bres Byte, #3
M
BSET
Bit Set
bset Byte, #3
M
BTJF
Jump if bit is false (0)
btjf Byte, #3, Jmp1
M
C
BTJT
Jump if bit is true (1)
btjt Byte, #3, Jmp1
M
C
CALL
Call subroutine
CALLR
Call subroutine relative
CLR
Clear
CP
Arithmetic Compare
tst(Reg - M)
reg
CPL
One Complement
A = FFH-A
DEC
Decrement
dec Y
HALT
Halt
IRET
Interrupt routine return
Pop CC, A, X, PC
INC
Increment
inc X
JP
Absolute Jump
jp [TBL.w]
JRA
Jump relative always
JRT
Jump relative
JRF
Never jump
JRIH
Jump if ext. interrupt = 1
JRIL
Jump if ext. interrupt = 0
JRH
Jump if H = 1
H=1?
JRNH
Jump if H = 0
H=0?
JRM
Jump if I = 1
I=1?
JRNM
Jump if I = 0
I=0?
JRMI
Jump if N = 1 (minus)
N=1?
JRPL
Jump if N = 0 (plus)
N=0?
JREQ
Jump if Z = 1 (equal)
Z=1?
JRNE
Jump if Z = 0 (not equal)
Z=0?
JRC
Jump if C = 1
C=1?
JRNC
Jump if C = 0
C=0?
JRULT
Jump if C = 1
Unsigned <
JRUGE
Jump if C = 0
Jmp if unsigned >=
JRUGT
Jump if (C + Z = 0)
Unsigned >
reg, M
0
1
N
Z
C
reg, M
N
Z
1
reg, M
N
Z
N
Z
N
Z
M
0
H
reg, M
I
C
jrf *
93/135
ST72104Gx-Auto, ST72215Gx-Auto, ST72216Gx-Auto, ST72254Gx-Auto
INSTRUCTION GROUPS (Cont’d)
Mnemo
Description
Function/Example
Dst
Src
JRULE
Jump if (C + Z = 1)
Unsigned <=
LD
Load
dst <= src
reg, M
M, reg
MUL
Multiply
X,A = X * A
A, X, Y
X, Y, A
NEG
Negate (2's compl)
neg $10
reg, M
NOP
No Operation
OR
OR operation
A=A+M
A
M
POP
Pop from the Stack
pop reg
reg
M
pop CC
CC
M
M
reg, CC
H
I
N
Z
N
Z
0
H
C
0
I
N
Z
N
Z
N
Z
C
C
PUSH
Push onto the Stack
push Y
RCF
Reset carry flag
C=0
RET
Subroutine Return
RIM
Enable Interrupts
I=0
RLC
Rotate left true C
C <= Dst <= C
reg, M
N
Z
C
RRC
Rotate right true C
C => Dst => C
reg, M
N
Z
C
RSP
Reset Stack Pointer
S = Max allowed
SBC
Subtract with Carry
A=A-M-C
N
Z
C
SCF
Set carry flag
C=1
SIM
Disable Interrupts
I=1
SLA
Shift left Arithmetic
C <= Dst <= 0
reg, M
N
Z
C
SLL
Shift left Logic
C <= Dst <= 0
reg, M
N
Z
C
SRL
Shift right Logic
0 => Dst => C
reg, M
0
Z
C
SRA
Shift right Arithmetic
Dst7 => Dst => C
reg, M
N
Z
C
SUB
Subtraction
A=A-M
A
N
Z
C
SWAP
SWAP nibbles
Dst[7..4] <=> Dst[3..0] reg, M
N
Z
TNZ
Test for Neg & Zero
tnz lbl1
N
Z
TRAP
S/W trap
S/W interrupt
WFI
Wait for Interrupt
XOR
Exclusive OR
N
Z
94/135
0
0
A
M
1
1
M
1
0
A = A XOR M
A
M
ST72104Gx-Auto, ST72215Gx-Auto, ST72216Gx-Auto, ST72254Gx-Auto
13 ELECTRICAL CHARACTERISTICS
13.1 PARAMETER CONDITIONS
Unless otherwise specified, all voltages are referred to VSS.
13.1.1 Minimum and Maximum Values
Unless otherwise specified the minimum and maximum values are guaranteed in the worst conditions of ambient temperature, supply voltage and
frequencies by tests in production on 100% of the
devices with an ambient temperature at TA=25°C
and TA=TAmax (given by the selected temperature
range).
Data based on characterization results, design
simulation and/or technology characteristics are
indicated in the table footnotes and are not tested
in production. Based on characterization, the minimum and maximum values refer to sample tests
and represent the mean value plus or minus three
times the standard deviation (mean±3Σ).
13.1.2 Typical Values
Unless otherwise specified, typical data are based
on TA=25°C, VDD=5V (for the 4.5V≤VDD≤5.5V
voltage range) and VDD=3.3V (for the 3V≤VDD≤4V
voltage range). They are given only as design
guidelines and are not tested.
13.1.3 Typical Curves
Unless otherwise specified, all typical curves are
given only as design guidelines and are not tested.
13.1.4 Loading Capacitor
The loading conditions used for pin parameter
measurement are shown in Figure 48.
13.1.5 Pin Input Voltage
The input voltage measurement on a pin of the device is described in Figure 49.
Figure 49. Pin Input Voltage
ST7 PIN
VIN
Figure 48. Pin Loading Conditions
ST7 PIN
CL
95/135
ST72104Gx-Auto, ST72215Gx-Auto, ST72216Gx-Auto, ST72254Gx-Auto
13.2 ABSOLUTE MAXIMUM RATINGS
Stresses above those listed as “absolute maximum ratings” may cause permanent damage to
the device. This is a stress rating only and functional operation of the device under these condi13.2.1 Voltage Characteristics
Symbol
VDD - VSS
VIN 1) & 2)
tions is not implied. Exposure to maximum rating
conditions for extended periods may affect device
reliability.
Ratings
Maximum value
Supply voltage
Unit
6.5
Input voltage on true open drain pin
VSS-0.3 to 6.5
Input voltage on any other pin
V
VSS-0.3 to VDD+0.3
VESD(HBM)
Electrostatic discharge voltage (Human Body Model)
VESD(MM)
Electrostatic discharge voltage (Machine Model)
see Section 13.7.2 "Absolute Electrical Sensitivity" on page 112
13.2.2 Current Characteristics
Symbol
IVDD
IVSS
Ratings
Maximum value
Total current into VDD power lines (source)
3)
80
Total current out of VSS ground lines (sink)
3)
80
Output current sunk by any standard I/O and control pin
IIO
IINJ(PIN) 2) & 4)
50
Output current source by any I/Os and control pin
- 25
Injected current on ISPSEL pin
±5
Injected current on RESET pin
±5
Injected current on any other pin
ΣIINJ(PIN) 2)
25
Output current sunk by any high sink I/O pin
Injected current on OSC1 and OSC2 pins
5) & 6)
Total injected current (sum of all I/O and control pins) 5)
Unit
mA
±5
±5
± 20
13.2.3 Thermal Characteristics
Symbol
TSTG
TJ
Ratings
Storage temperature range
Value
Unit
-65 to +150
°C
Maximum junction temperature
(see Section 14.3 "THERMAL CHARACTERISTICS" on page 128)
Notes:
1. Directly connecting the RESET and I/O pins to VDD or VSS could damage the device if an unintentional internal reset
is generated or an unexpected change of the I/O configuration occurs (for example, due to a corrupted program counter).
To guarantee safe operation, this connection has to be done through a pull-up or pull-down resistor (typical: 4.7kΩ for
RESET, 10kΩ for I/Os). Unused I/O pins must be tied in the same way to VDD or VSS according to their reset configuration.
2. When the current limitation is not possible, the VIN absolute maximum rating must be respected, otherwise refer to
IINJ(PIN) specification. A positive injection is induced by VIN>VDD while a negative injection is induced by VIN<VSS.
3. All power (VDD) and ground (VSS) lines must always be connected to the external supply.
4. Negative injection disturbs the analog performance of the device. In particular, it induces leakage currents throughout
the device including the analog inputs. To avoid undesirable effects on the analog functions, care must be taken:
- Analog input pins must have a negative injection less than 0.8 mA (assuming that the impedance of the analog voltage
is lower than the specified limits)
- Pure digital pins must have a negative injection less than 1.6mA. In addition, it is recommended to inject the current as
far as possible from the analog input pins.
5. When several inputs are submitted to a current injection, the maximum ΣIINJ(PIN) is the absolute sum of the positive
and negative injected currents (instantaneous values). These results are based on characterization with ΣIINJ(PIN) maximum current injection on four I/O port pins of the device.
6. True open drain I/O port pins do not accept positive injection.
96/135
ST72104Gx-Auto, ST72215Gx-Auto, ST72216Gx-Auto, ST72254Gx-Auto
13.3 OPERATING CONDITIONS
13.3.1 General Operating Conditions
Symbol
VDD
fOSC
Conditions
Min
Max
Unit
Supply voltage
Parameter
see Figure 50 and Figure 51
3.2
5.5
V
External clock frequency
VDD≥3.5V for ROM devices
VDD≥4.5V for Flash devices
0 1)
VDD≥3.2V
Ambient temperature range
MHz
8
Suffix A version
TA
16
+85
Suffix B version
-40
Suffix C version
+105
°C
+125
Figure 50. fOSC Maximum Operating Frequency Versus VDD Supply Voltage for ROM Devices 2)
fOSC [MHz]
FUNCTIONALITY
GUARANTEED
IN THIS AREA
16
FUNCTIONALITY
NOT GUARANTEED
IN THIS AREA
FUNCTIONALITY
NOT GUARANTEED
IN THIS AREA
WITH RESONATOR 1)
8
4
1
0
SUPPLY VOLTAGE [V]
2.5
3.2
3.5
3.85 4
4.5
5
5.5
97/135
ST72104Gx-Auto, ST72215Gx-Auto, ST72216Gx-Auto, ST72254Gx-Auto
OPERATING CONDITIONS (Cont’d)
Figure 51. fOSC Maximum Operating Frequency Versus VDD Supply Voltage for Flash devices 2)
fOSC [MHz]
FUNCTIONALITY
NOT GUARANTEED
IN THIS AREA AT TA > 85°C
FUNCTIONALITY
GUARANTEED
IN THIS AREA 3)
16
FUNCTIONALITY
NOT GUARANTEED
IN THIS AREA
12
FUNCTIONALITY
NOT GUARANTEED
IN THIS AREA
WITH RESONATOR 1)
8
4
1
0
SUPPLY VOLTAGE [V]
2.5
3.2
3.5
3.85 4
4.5
5
5.5
Notes:
1. Guaranteed by construction. A/D operation and resonator oscillator start-up are not guaranteed below 1MHz.
2. Operating conditions with TA=-40 to +125°C.
3. Flash programming tested in production at maximum TA with two different conditions: VDD=5.5V, fCPU=8MHz and
VDD=3.2V, fCPU=4MHz.
98/135
ST72104Gx-Auto, ST72215Gx-Auto, ST72216Gx-Auto, ST72254Gx-Auto
OPERATING CONDITIONS (Cont’d)
13.3.2 Operating Conditions with Low Voltage Detector (LVD)
Subject to general operating conditions for VDD, fOSC, and TA.
Symbol
Parameter
VIT+
Reset release threshold
(VDD rise)
VIT-
Reset generation threshold
(VDD fall)
Vhyst
VtPOR
tg(VDD)
LVD voltage threshold hysteresis
VDD rise time rate 3)
Filtered glitch delay on VDD 2)
Conditions
High Threshold
Med. Threshold
Low Threshold
High Threshold
Med. Threshold
Low Threshold4)
VIT+-VIT-
Typ 1)
4.30
3.90
3.35
4.05
3.65
3.10
250
Min
4.10 2)
3.75 2)
3.25 2)
3.85 2)
3.50 2)
3.00
200
0.2
Not detected by the LVD
Max
4.50
4.05
3.55
4.30
3.95
3.35
300
50
40
Unit
V
mV
V/ms
ns
Figure 52. High LVD Threshold Versus VDD and fOSC for Flash devices 3)
fOSC [MHz]
DEVICE UNDER
RESET
IN THIS AREA
FUNCTIONALITY AND RESET NOT GUARANTEED IN THIS AREA
FOR TEMPERATURES HIGHER THAN 85°C
16
12
FUNCTIONALITY
NOT GUARANTEED
IN THIS AREA
FUNCTIONAL AREA
8
0
2.5
3
3.5
VIT-≥3.85
SUPPLY VOLTAGE [V]
4
4.5
5
5.5
Figure 53. Medium LVD Threshold Versus VDD and fOSC for Flash devices 3)
fOSC [MHz]
DEVICE UNDER
RESET
IN THIS AREA
FUNCTIONALITY AND RESET NOT GUARANTEED IN THIS AREA
FOR TEMPERATURES HIGHER THAN 85°C
16
12
FUNCTIONALITY
NOT GUARANTEED
IN THIS AREA
FUNCTIONAL AREA
8
0
2.5
VIT-≥3.5V
3
SUPPLY VOLTAGE [V]
4
4.5
5
5.5
Figure 54. Low LVD Threshold Versus VDD and fOSC for Flash devices 2)4)
fOSC [MHz]
FUNCTIONALITY NOT GUARANTEED IN THIS AREA
FOR TEMPERATURES HIGHER THAN 85°C
FUNCTIONALITY
NOT GUARANTEED
IN THIS AREA
16
12
DEVICE UNDER
RESET
IN THIS AREA
FUNCTIONAL AREA
8
SEE NOTE 4
0
2.5
VIT-≥3V 3.2
SUPPLY VOLTAGE [V]
3.5
4
4.5
5
5.5
Notes:
1. LVD typical data are based on TA=25°C. They are given only as design guidelines and are not tested.
2. Data based on characterization results, not tested in production.
3. The VDD rise time rate condition is needed to insure a correct device power-on and LVD reset. Not tested in production.
4. If the low LVD threshold is selected, when VDD falls below 3.2V, (VDD minimum operating voltage), the device is guaranteed to continue functioning until it goes into reset state. The specified VDD min. value is necessary in the device power
on phase, but during a power down phase or voltage drop the device will function below this min. level.
99/135
ST72104Gx-Auto, ST72215Gx-Auto, ST72216Gx-Auto, ST72254Gx-Auto
FUNCTIONAL OPERATING CONDITIONS (Cont’d)
Figure 55. High LVD Threshold Versus VDD and fOSC for ROM devices 2)
fOSC [MHz]
DEVICE UNDER
RESET
IN THIS AREA
FUNCTIONALITY
NOT GUARANTEED
IN THIS AREA
16
FUNCTIONAL AREA
8
0
2.5
3
3.5
VIT-≥3.85
SUPPLY VOLTAGE [V]
4
4.5
5
5.5
Figure 56. Medium LVD Threshold Versus VDD and fOSC for ROM devices 2)
fOSC [MHz]
DEVICE UNDER
RESET
IN THIS AREA
FUNCTIONALITY
NOT GUARANTEED
IN THIS AREA
16
FUNCTIONAL AREA
8
0
2.5
3
VIT-≥3.5V
SUPPLY VOLTAGE [V]
4
4.5
5
5.5
Figure 57. Low LVD Threshold Versus VDD and fOSC for ROM devices 2)3)
fOSC [MHz]
FUNCTIONALITY
NOT GUARANTEED
IN THIS AREA
16
DEVICE UNDER
RESET
IN THIS AREA
FUNCTIONAL AREA
8
0
2.5
VIT-≥3.00V
SUPPLY VOLTAGE [V]
3.5
4
4.5
5
5.5
Notes:
1. LVD typical data are based on TA=25°C. They are given only as design guidelines and are not tested.
2. The minimum VDD rise time rate is needed to insure a correct device power-on and LVD reset. Not tested in production.
3. If the low LVD threshold is selected, when VDD falls below 3.2V, the device is guaranteed to be either functioning or
under reset.
100/135
ST72104Gx-Auto, ST72215Gx-Auto, ST72216Gx-Auto, ST72254Gx-Auto
13.4 SUPPLY CURRENT CHARACTERISTICS
The following current consumption specified for
the ST7 functional operating modes over temperature range does not take into account the clock
source current consumption. To get the total deSymbol
∆IDD(∆Ta)
Parameter
Supply current variation vs. temperature
vice consumption, the two current values must be
added (except for HALT mode for which the clock
is stopped).
Conditions
Constant VDD and fCPU
Max
10
Unit
%
Max 2)
900
2500
9000
450
550
1250
550
1350
4500
250
300
700
Unit
13.4.1 RUN and SLOW Modes
Parameter
3.2V≤VDD≤3.6V 4.5V≤VDD≤5.5V
Symbol
Supply current in RUN mode 3)
(see Figure 58)
Supply current in SLOW mode 4)
(see Figure 59)
IDD
Supply current in RUN mode 3)
(see Figure 58)
Supply current in SLOW mode 4)
(see Figure 59)
Figure 58. Typical IDD in RUN vs. fCPU
IDD [mA]
7
0.8
6
2MHz
4MHz
500kHz
µA
Figure 59. Typical IDD in SLOW vs. fCPU
IDD [mA]
8MHz
Typ 1)
500
1500
5600
150
250
670
300
970
3600
100
170
420
Conditions
fOSC=1MHz, fCPU=500kHz
fOSC=4MHz, fCPU=2MHz
fOSC=16MHz, fCPU=8MHz
fOSC=1MHz, fCPU=31.25kHz
fOSC=4MHz, fCPU=125kHz
fOSC=16MHz, fCPU=500kHz
fOSC=1MHz, fCPU=500kHz
fOSC=4MHz, fCPU=2MHz
fOSC=16MHz, fCPU=8MHz
fOSC=1MHz, fCPU=31.25kHz
fOSC=4MHz, fCPU=125kHz
fOSC=16MHz, fCPU=500kHz
500kHz
125kHz
250kHz
31.25kHz
0.7
0.6
5
0.5
4
0.4
3
0.3
2
0.2
1
0.1
0
0
3.2
3.5
4
4.5
VDD [V]
5
5.5
3.2
3.5
4
4.5
5
5.5
VDD [V]
Notes:
1. Typical data are based on TA=25°C, VDD=5V (4.5V≤VDD≤5.5V range) and VDD=3.4V (3.2V≤VDD≤3.6V range).
2. Data based on characterization results, tested in production at VDD max. and fCPU max.
3. CPU running with memory access, all I/O pins in input mode with a static value at VDD or VSS (no load), all peripherals
in reset state; clock input (OSC1) driven by external square wave, CSS and LVD disabled.
4. SLOW mode selected with fCPU based on fOSC divided by 32. All I/O pins in input mode with a static value at VDD or
VSS (no load), all peripherals in reset state; clock input (OSC1) driven by external square wave, CSS and LVD disabled.
101/135
ST72104Gx-Auto, ST72215Gx-Auto, ST72216Gx-Auto, ST72254Gx-Auto
SUPPLY CURRENT CHARACTERISTICS (Cont’d)
13.4.2 WAIT and SLOW WAIT Modes
Parameter
Supply current in WAIT mode
(see Figure 60)
3)
Supply current in SLOW WAIT mode 4)
(see Figure 61)
IDD
Supply current in WAIT mode 3)
(see Figure 60)
Supply current in SLOW WAIT mode 4)
(see Figure 61)
3.2V≤VDD≤3.6V 4.5V≤VDD≤5.5V
Symbol
Figure 60. Typical IDD in WAIT vs. fCPU
Typ 1)
Max 2)
150
560
2200
280
900
3000
fOSC=1MHz, fCPU=31.25kHz
fOSC=4MHz, fCPU=125kHz
fOSC=16MHz, fCPU=500kHz
20
90
340
70
190
850
fOSC=1MHz, fCPU=500kHz
fOSC=4MHz, fCPU=2MHz
fOSC=16MHz, fCPU=8MHz
90
350
1370
200
550
1900
fOSC=1MHz, fCPU=31.25kHz
fOSC=4MHz, fCPU=125kHz
fOSC=16MHz, fCPU=500kHz
10
50
200
20
80
350
Conditions
fOSC=1MHz, fCPU=500kHz
fOSC=4MHz, fCPU=2MHz
fOSC=16MHz, fCPU=8MHz
Unit
µA
Figure 61. Typical IDD in SLOW-WAIT vs. fCPU
IDD [mA]
IDD [mA]
3
8MHz
2MHz
4MHz
500kHz
0.35
500kHz
125kHz
250kHz
31.25kHz
0.3
2.5
0.25
2
0.2
1.5
0.15
1
0.1
0.5
0.05
0
0
3.2
3.5
4
4.5
VDD [V]
5
5.5
3.2
3.5
4
4.5
5
5.5
VDD [V]
Notes:
1. Typical data are based on TA=25°C, VDD=5V (4.5V≤VDD≤5.5V range) and VDD=3.4V (3.2V≤VDD≤3.6V range).
2. Data based on characterization results, tested in production at VDD max. and fCPU max.
3. All I/O pins in input mode with a static value at VDD or VSS (no load), all peripherals in reset state; clock input (OSC1)
driven by external square wave, CSS and LVD disabled.
4. SLOW-WAIT mode selected with fCPU based on fOSC divided by 32. All I/O pins in input mode with a static value at
VDD or VSS (no load), all peripherals in reset state; clock input (OSC1) driven by external square wave, CSS and LVD
disabled.
102/135
ST72104Gx-Auto, ST72215Gx-Auto, ST72216Gx-Auto, ST72254Gx-Auto
SUPPLY CURRENT CHARACTERISTICS (Cont’d)
13.4.3 HALT Mode
Symbol
IDD
Parameter
Supply current in HALT mode 2)
13.4.4 Supply and Clock Managers
The previous current consumption specified for
the ST7 functional operating modes over temperature range does not take into account the clock
Symbol
IDD(CK)
IDD(LVD)
Conditions
-40°C≤TA≤+85°C
VDD=5.5V
-40°C≤TA≤+125°C
-40°C≤TA≤+85°C
VDD=3.6V
-40°C≤TA≤+125°C
Typ 1)
-
Max
10
150
6
100
Max 3)
Supply current of internal RC oscillator
500
750
Supply current of external RC oscillator 4)
525
750
LP: Low power oscillator
MP: Medium power oscillator
4)
&
5)
Supply current of resonator oscillator
MS: Medium speed oscillator
HS: High speed oscillator
200
300
450
700
400
550
750
1000
Clock security system supply current
150
350
100
150
LVD supply current
µA
source current consumption. To get the total device consumption, the two current values must be
added (except for HALT mode).
Typ 1)
Parameter
Unit
Conditions
HALT mode
Unit
µA
13.4.5 On-Chip Peripherals
Symbol
Parameter
IDD(TIM)
16-bit Timer supply current 6)
IDD(SPI)
SPI supply current 7)
IDD(I2C)
I2C supply current 8)
IDD(ADC)
ADC supply current when converting 9)
Conditions
VDD=3.4V
fCPU=8MHz
VDD=5.0V
VDD=3.4V
fCPU=8MHz
VDD=5.0V
VDD=3.4V
fCPU=8MHz
VDD=5.0V
VDD=3.4V
fADC=4MHz
VDD=5.0V
Typ
50
150
250
350
250
350
800
1100
Unit
µA
Notes:
1. Typical data are based on TA=25°C.
2. All I/O pins in input mode with a static value at VDD or VSS (no load), CSS and LVD disabled. Data based on characterization results, tested in production at VDD max. and fCPU max.
3. Data based on characterization results, not tested in production.
4. Data based on characterization results done with the external components specified in Section 13.5.3 and Section
13.5.4, not tested in production.
5. As the oscillator is based on a current source, the consumption does not depend on the voltage.
6. Data based on a differential IDD measurement between reset configuration (timer counter running at fCPU/4) and timer
counter stopped (selecting external clock capability). Data valid for one timer.
7. Data based on a differential IDD measurement between reset configuration and a permanent SPI master communication (data sent equal to 55h).
8. Data based on a differential IDD measurement between reset configuration and I2C peripheral enabled (PE bit set).
9. Data based on a differential IDD measurement between reset configuration and continuous A/D conversions.
103/135
ST72104Gx-Auto, ST72215Gx-Auto, ST72216Gx-Auto, ST72254Gx-Auto
13.5 CLOCK AND TIMING CHARACTERISTICS
Subject to general operating conditions for VDD, fOSC, and TA.
13.5.1 General Timings
Symbol
tc(INST)
Parameter
Instruction cycle time
Interrupt reaction time
tv(IT) = ∆tc(INST) + 10
tv(IT)
Conditions
Typ 1)
Min
Max
Unit
2
3
12
tCPU
fCPU=8MHz
250
375
1500
ns
10
22
tCPU
fCPU=8MHz
1.25
2.75
µs
Max
VDD
0.3xVDD
Unit
2)
13.5.2 External Clock Source
Symbol
VOSC1H
VOSC1L
tw(OSC1H)
tw(OSC1L)
tr(OSC1)
tf(OSC1)
IL
Parameter
OSC1 input pin high level voltage
OSC1 input pin low level voltage
Conditions
OSC1 high or low time 3)
Min
0.7xVDD
VSS
see Figure 62
Typ
V
15
ns
OSC1 rise or fall time 3)
15
VSS≤VIN≤VDD
OSCx Input leakage current
±1
µA
Figure 62. Typical Application with an External Clock Source
90%
VOSC1H
10%
VOSC1L
tr(OSC1)
tf(OSC1)
OSC2
tw(OSC1H)
tw(OSC1L)
Not connected internally
fOSC
EXTERNAL
CLOCK SOURCE
OSC1
IL
ST72XXX
Notes:
1. Data based on typical application software.
2. Time measured between interrupt event and interrupt vector fetch. ∆tc(INST) is the number of tCPU cycles needed to
finish the current instruction execution.
3. Data based on design simulation and/or technology characteristics, not tested in production.
104/135
ST72104Gx-Auto, ST72215Gx-Auto, ST72216Gx-Auto, ST72254Gx-Auto
CLOCK AND TIMING CHARACTERISTICS (Cont’d)
13.5.3 Crystal and Ceramic Resonator Oscillators
The ST7 internal clock can be supplied with four
different Crystal/Ceramic resonator oscillators. All
the information given in this paragraph are based
on characterization results with specified typical
external components. In the application, the resonator and the load capacitors have to be placed as
Symbol
fOSC
RF
CL1
CL2
i2
Parameter
close as possible to the oscillator pins in order to
minimize output distortion and start-up stabilization time. Refer to the crystal/ceramic resonator
manufacturer for more details (frequency, package, accuracy...).
Conditions
LP: Low power oscillator
MP: Medium power oscillator
MS: Medium speed oscillator
HS: High speed oscillator
Oscillator Frequency 3)
Feedback resistor
Recommended load capacitance versus equivalent serial resistance of the
crystal or ceramic resonator (RS)
OSC2 driving current
RS=200ΩLP oscillator
RS=200ΩMP oscillator
RS=200ΩMS oscillator
RS=100ΩHS oscillator
VDD=5VLP oscillator
VIN=VSSMP oscillator
MS oscillator
HS oscillator
Min
1
>2
>4
>8
20
38
32
18
15
40
110
180
400
Max
2
4
8
16
40
56
46
26
21
100
190
360
700
Unit
MHz
kΩ
pF
µA
13.5.3.1 Typical Crystal Resonators
Reference
LP
S-200-30-30/50
MP
MS
HS
JAUCH
Option Byte
Configuration
SS3-400-30-30/30
CL1 CL2 tSU(osc)
[pF] [pF] [ms] 2)
Characteristic 1)
Freq.
2MHz ∆fOSC=[±30ppm25°C,±30ppm∆Ta], Typ. RS=200Ω
4MHz ∆fOSC=[±30ppm25°C,±30ppm∆Ta], Typ. RS=60Ω
8MHz ∆fOSC=[±30ppm25°C,±30ppm∆Ta], Typ. RS=25Ω
SS3-1600-30-30/30 16MHz ∆fOSC=[±30ppm25°C,±30ppm∆Ta], Typ. RS=15Ω
SS3-800-30-30/30
33
34
33
34
10~15
7~10
33
34
2.5~3
33
34
1~1.5
Figure 63. Typical Application with a Crystal Resonator
i2
fOSC
CL1
OSC1
RESONATOR
CL2
RF
OSC2
ST72XXX
Notes:
1. Resonator characteristics given by the crystal manufacturer.
2. tSU(OSC) is the typical oscillator start-up time measured between VDD=2.8V and the fetch of the first instruction (with a
quick VDD ramp-up from 0 to 5V (<50µs).
3. The oscillator selection can be optimized in terms of supply current using an high quality resonator with small RS value.
Refer to crystal manufacturer for more details.
105/135
ST72104Gx-Auto, ST72215Gx-Auto, ST72216Gx-Auto, ST72254Gx-Auto
CLOCK AND TIMING CHARACTERISTICS (Cont’d)
13.5.3.2 Typical Ceramic Resonators
Symbol
Parameter
tSU(osc)
Ceramic resonator start-up time
Conditions
LP
2MHz
MP
4MHz
MS
8MHz
HS
16MHz
Typ
4.2
2.1
1.1
0.7
Unit
ms
tSU(OSC) is the typical oscillator start-up time measured between VDD=2.8V and the fetch of the first instruction (with a quick VDD ramp-up from 0 to 5V (<50µs).
Table 21. Typical Ceramic Resonators for Automotive Applications
Option Byte
Config.
fOSC
(MHz)
1
LP
2
2
MP
4
4
MS
8
8
10
HS
12
162)
Resonator Part Number1)
CL1
CL2
RFEXT
RD
[pF]3)
[pF]3)
[kΩ]
[kΩ]
100
100
(47)
(47)
CSB1000JA
CSBF1000JA
CSTS0200MGA06
CSTCC2.00MGA0H6
CSTS0200MGA06
CSTCC2.00MGA0H6
CSTS0400MGA06
CSTCC4.00MGA0H6
CSTS0400MGA06
CSTCC4.00MGA0H6
Open
CSTS0800MGA06
CSTCC8.00MGA0H6
0
CSTS0800MGA06
CSTCC8.00MGA0H6
CSTS1000MGA03
CSTCC10.0MGA
(15)
(15)
CST12.0MTWA
30
30
CSTCS12.0MTA
(30)
(30)
CSA16.00MXZA040
15
15
CST16.00MXWA0C3
(15)
(15)
CSACV16.00MXA040Q
15
15
CSTCV16.00MXA0H3Q
(15)
(15)
Notes:
1. Murata Ceralock (refer to Table 22 for correlation factor)
2. VDD 4.5 to 5.5V
3. Values in parentheses refer to the capacitors integrated in the resonator
106/135
3.3
10
ST72104Gx-Auto, ST72215Gx-Auto, ST72216Gx-Auto, ST72254Gx-Auto
CLOCK AND TIMING CHARACTERISTICS (Cont’d)
Figure 64. Typical Application with Ceramic Resonator
WHEN RESONATOR WITH
INTEGRATED CAPACITORS
i2
fOSC
CL1
OSC1
RESONATOR
RF(EXT)
CL2
RF
OSC2
ST72XXX
RD
Notes:
1. Resonator characteristics given by the ceramic resonator manufacturer.
2. tSU(OSC) is the typical oscillator start-up time measured between VDD=2.8V and the fetch of the first instruction (with a
quick VDD ramp-up from 0 to 5V (<50µs).
3. The oscillator selection can be optimized in terms of supply current using an high quality resonator with small RS value.
Refer to ceramic resonator manufacturer for more details.
Table 22. Ceramic Resonator Frequency Correlation Factor1)
Resonator1)
Option Byte Configuration
LP
CSB1000J
CSTS0200MG06
CSTCC2.00MG0H6
CSTS0200MG06
MP
MS
HS
CSTCC2.00MG0H6
CSTS0400MG06
CSTS0400MGA06
CSTCC4.00MG0H6
CSTS0200MG06
CSTCC2.00MG0H6
CSTS0400MG06
CSTS0400MGA06
CSTCC4.00MG0H6
CSTS0200MG06
CSTS0800MG06
CSTS0800MGA06
CSTCC8.00MG0H6
CSTS1000MG03
CSTCC10.0MG
CST12.0MTW
CSTCV12.0MTJ0C4
CSTCS12.0MTA
CSA16.00MXZ040
CSACV16.00MXJ040
CSACW1600MX03
CSACV16.00MXA040Q
Correlation %
+0.03
-0.16
-0.10
-0.15
-0.14
0.00
-0.01
-0.02
-0.15
-0.14
0.00
-0.01
-0.02
-0.15
+0.10
+0.07
+0.09
+0.34
+0.75
+0.45
+0.30
+0.50
+0.10
+0.09
+0.03
+0.09
Reference IC
4069UBE
74HCU04
74HCU04
74HCU04
4069UBP
4069UBE
4069UBE
40H004
4069UBE
74HCU04
Notes:
1. See Table 21 for ceramic resonator values.
107/135
ST72104Gx-Auto, ST72215Gx-Auto, ST72216Gx-Auto, ST72254Gx-Auto
CLOCK CHARACTERISTICS (Cont’d)
13.5.4 RC Oscillators
The ST7 internal clock can be supplied with an RC
oscillator. This oscillator can be used with internal
Symbol
fOSC
Parameter
Internal RC oscillator frequency 1)
External RC oscillator frequency 2)
Internal RC oscillator start-up time 3)
or external components (selectable by option
byte).
Conditions
see Figure 66
Min
3.60
1
tSU(OSC)
External RC oscillator start-up time 3)
REX = 47KΩ, CEX = “0”pF
REX = 47KΩ, CEX = 100pF
REX = 10KΩ, CEX = 6.8pF
REX = 10KΩ, CEX = 470pF
REX
CEX
Oscillator external resistor 4)
Oscillator external capacitor
see Figure 67
Typ
Max
5.10
14
Unit
MHz
2.0
1.0
6.5
0.7
3.0
ms
10
0 5)
47
470
KΩ
pF
Figure 65. Typical Application with RC oscillator
ST72XXX
VDD
INTERNAL RC
Current copy
EXTERNAL RC
VREF
REX
CEX
OSC1
4.3
fOSC
Voltage generator
OSC2
Figure 66. Typical Internal RC Oscillator
fosc [MHz]
+
-
CEX discharge
Figure 67. Typical External RC Oscillator
fosc [MHz]
-40°C
+85°C
+25°C
+125°C
Rex=10KOhm
20
Rex=15KOhm
Rex=22KOhm
4.2
15
Rex=33KOhm
Rex=39KOhm
4.1
10
Rex=47KOhm
4
5
3.9
0
3.8
3.2
5.5
VDD [V]
0
6.8
22
47
100
270
470
Cex [pF]
Notes:
1. Data based on characterization results.
2. Guaranteed frequency range with the specified CEX and REX ranges taking into account the device process variation.
Data based on design simulation.
3. Data based on characterization results done with VDD nominal at 5V, not tested in production.
4. REX must have a positive temperature coefficient (ppm/°C), carbon resistors should therefore not be used.
5. Important: When no external CEX is applied, the capacitance to be considered is the global parasitic capacitance
which is subject to high variation (package, application...). In this case, the RC oscillator frequency tuning has to be done
by trying out several resistor values.
108/135
ST72104Gx-Auto, ST72215Gx-Auto, ST72216Gx-Auto, ST72254Gx-Auto
CLOCK CHARACTERISTICS (Cont’d)
13.5.5 Clock Security System (CSS)
Symbol
Parameter
fSFOSC
Safe Oscillator Frequency 1)
fGFOSC
Glitch Filtered Frequency 2)
Conditions
TA=25°C, VDD=5.0V
TA=25°C, VDD=3.4V
Min
250
190
Typ
340
260
30
Max
550
450
Unit
kHz
MHz
Figure 68. Typical Safe Oscillator Frequencies
fosc [kHz]
-40°C
+85°C
400
+25°C
+125°C
350
300
250
200
3.2
5.5
VDD [V]
Notes:
1. Data based on characterization results, tested in production between 90 kHz and 600 kHz.
2. Filtered glitch on the fOSC signal. See functional description in Section 6.5 on page 23 for more details.
109/135
ST72104Gx-Auto, ST72215Gx-Auto, ST72216Gx-Auto, ST72254Gx-Auto
13.6 MEMORY CHARACTERISTICS
Subject to general operating conditions for VDD, fOSC, and TA unless otherwise specified.
13.6.1 RAM and Hardware Registers
Symbol
VRM
Parameter
Data retention mode
1)
Conditions
HALT mode (or RESET)
Min
Typ
Max
1.6
Unit
V
13.6.2 Flash Program Memory
Symbol
TA(prog)
tprog
tret
NRW
Parameter
Programming temperature range 2)
Programming time for 1~16 bytes 3)
Programming time for 4 or 8Kbytes
Data retention 5)
Write erase cycles 5)
Conditions
TA=+25°C
TA=+25°C
TA=+55°C 4)
TA=+25°C
Min
0
20
100
Typ
25
8
2.1
Max
70
25
6.4
Unit
°C
ms
sec
years
cycles
Notes:
1. Minimum VDD supply voltage without losing data stored in RAM (in HALT mode or under RESET) or in hardware registers (only in HALT mode). Guaranteed by construction, not tested in production.
2. Data based on characterization results, tested in production at TA=25°C.
3. Up to 16 bytes can be programmed at a time for a 4 Kbyte Flash block (then up to 32 bytes at a time for an 8 Kbyte
device)
4. The data retention time increases when the TA decreases.
5. Data based on reliability test results and monitored in production.
110/135
ST72104Gx-Auto, ST72215Gx-Auto, ST72216Gx-Auto, ST72254Gx-Auto
13.7 EMC CHARACTERISTICS
Susceptibility tests are performed on a sample basis during product characterization.
13.7.1 Functional EMS
(Electromagnetic Susceptibility)
Based on a simple running application on the
product (toggling two LEDs through I/O ports), the
product is stressed by two electromagnetic events
until a failure occurs (indicated by the LEDs).
Symbol
VFESD
VFFTB
Parameter
Voltage limits to be applied on any I/O pin
to induce a functional disturbance
Fast transient voltage burst limits to be applied through 100pF on VDD and VDD pins
to induce a functional disturbance
ESD: Electrostatic Discharge (positive and
negative) is applied on all pins of the device until
a functional disturbance occurs. This test
conforms with the IEC 1000-4-2 standard.
■ FTB: A Burst of Fast Transient voltage (positive
and negative) is applied to VDD and VSS through
a 100pF capacitor, until a functional disturbance
occurs. This test conforms with the IEC 1000-44 standard.
A device reset allows normal operations to be resumed.
■
Conditions
VDD=5V, TA=+25°C, fOSC=8MHz
conforms to IEC 1000-4-2
VDD=5V, TA=+25°C, fOSC=8MHz
conforms to IEC 1000-4-4
Neg 1)
Pos 1)
-1
1
-4
4
Unit
kV
Figure 69. EMC Recommended star network power supply connection 2)
ST72XXX
10µF 0.1µF
ST7
DIGITAL NOISE
FILTERING
VDD
VSS
VDD
POWER
SUPPLY
SOURCE
VSSA
EXTERNAL
NOISE
FILTERING
VDDA
0.1µF
Notes:
1. Data based on characterization results, not tested in production.
2. The suggested 10µF and 0.1µF decoupling capacitors on the power supply lines are proposed as a good price vs. EMC
performance tradeoff. They have to be put as close as possible to the device power supply pins. Other EMC recommendations are given in other sections (I/Os, RESET, OSCx pin characteristics).
111/135
ST72104Gx-Auto, ST72215Gx-Auto, ST72216Gx-Auto, ST72254Gx-Auto
EMC CHARACTERISTICS (Cont’d)
13.7.2 Absolute Electrical Sensitivity
Based on three different tests (ESD, LU and DLU)
using specific measurement methods, the product
is stressed in order to determine its performance in
terms of electrical sensitivity. For more details, refer to the AN1181 ST7 application note.
13.7.2.1 Electrostatic Discharge (ESD)
Electrostatic Discharges (3 positive then 3 negative pulses separated by 1 second) are applied to
the pins of each sample according to each pin
combination. The sample size depends of the
number of supply pins of the device (3 parts*(n+1)
supply pin). Two models are usually simulated:
Human Body Model and Machine Model. This test
conforms to the JESD22-A114A/A115A standard.
See Figure 70 and the following test sequences.
Machine Model Test Sequence
– CL is loaded through S1 by the HV pulse generator.
– S1 switches position from generator to ST7.
– A discharge from CL to the ST7 occurs.
– S2 must be closed 10 to 100ms after the pulse
delivery period to ensure the ST7 is not left in
charge state. S2 must be opened at least 10ms
prior to the delivery of the next pulse.
– R (machine resistance), in series with S2, ensures a slow discharge of the ST7.
Human Body Model Test Sequence
– CL is loaded through S1 by the HV pulse generator.
– S1 switches position from generator to R.
– A discharge from CL through R (body resistance)
to the ST7 occurs.
– S2 must be closed 10 to 100ms after the pulse
delivery period to ensure the ST7 is not left in
charge state. S2 must be opened at least 10ms
prior to the delivery of the next pulse.
Absolute Maximum Ratings
Symbol
Ratings
Maximum value 1) Unit
Conditions
VESD(HBM)
Electrostatic discharge voltage
(Human Body Model)
TA=+25°C
2000
VESD(MM)
Electrostatic discharge voltage
(Machine Model)
TA=+25°C
200
V
Figure 70. Typical Equivalent ESD Circuits
S1
CL=100pF
S1
ST7
S2
HIGH VOLTAGE
PULSE
GENERATOR
ST7
CL=200pF
HUMAN BODY MODEL
Notes:
1. Data based on characterization results, not tested in production.
112/135
MACHINE MODEL
R=10k~10MΩ
HIGH VOLTAGE
PULSE
GENERATOR
R=1500Ω
S2
ST72104Gx-Auto, ST72215Gx-Auto, ST72216Gx-Auto, ST72254Gx-Auto
EMC CHARACTERISTICS (Cont’d)
13.7.2.2 Static and Dynamic Latch-Up
■ LU: 3 complementary static tests are required
on 10 parts to assess the latch-up performance.
A supply overvoltage (applied to each power
supply pin), a current injection (applied to each
input, output and configurable I/O pin) and a
power supply switch sequence are performed
on each sample. This test conforms to the EIA/
JESD 78 IC latch-up standard. For more details,
refer to the AN1181 ST7 application note.
■
DLU: Electrostatic Discharges (one positive
then one negative test) are applied to each pin
of three samples when the micro is running to
assess the latch-up performance in dynamic
mode. Power supplies are set to the typical
values, the oscillator is connected as near as
possible to the pins of the micro and the
component is put in reset mode. This test
conforms to the IEC1000-4-2 and SAEJ1752/3
standards and is described in Figure 71. For
more details, refer to the AN1181 ST7
application note.
Electrical Sensitivities
Symbol
Parameter
Class 1)
Conditions
LU
Static latch-up class
TA=+25°C
TA=+85°C
A
A
DLU
Dynamic latch-up class
VDD=5.5V, fOSC=4MHz, TA=+25°C
A
Figure 71. Simplified Diagram of the ESD Generator for DLU
RCH=50MΩ
CS=150pF
ESD
GENERATOR 2)
RD=330Ω
DISCHARGE TIP
VDD
VSS
HV RELAY
ST7
DISCHARGE
RETURN CONNECTION
Notes:
1. Class description: A Class is an STMicroelectronics internal specification. All its limits are higher than the JEDEC specifications, that means when a device belongs to Class A it exceeds the JEDEC standard. B Class strictly covers all the
JEDEC criteria (international standard).
2. Schaffner NSG435 with a pointed test finger.
113/135
ST72104Gx-Auto, ST72215Gx-Auto, ST72216Gx-Auto, ST72254Gx-Auto
EMC CHARACTERISTICS (Cont’d)
13.7.3 ESD Pin Protection Strategy
To protect an integrated circuit against Electrostatic Discharge the stress must be controlled to prevent degradation or destruction of the circuit elements. The stress generally affects the circuit elements which are connected to the pads but can
also affect the internal devices when the supply
pads receive the stress. The elements to be protected must not receive excessive current, voltage
or heating within their structure.
An ESD network combines the different input and
output ESD protections. This network works, by allowing safe discharge paths for the pins subjected
to ESD stress. Two critical ESD stress cases are
presented in Figure 72 and Figure 73 for standard
pins and in Figure 74 and Figure 75 for true open
drain pins.
Standard Pin Protection
To protect the output structure the following elements are added:
– A diode to VDD (3a) and a diode from VSS (3b)
– A protection device between VDD and VSS (4)
To protect the input structure the following elements are added:
– A resistor in series with the pad (1)
– A diode to VDD (2a) and a diode from VSS (2b)
– A protection device between VDD and VSS (4)
Figure 72. Positive Stress on a Standard Pad vs. VSS
VDD
VDD
(2a)
(3a)
(1)
OUT
(4)
IN
Main path
(2b)
(3b)
Path to avoid
VSS
VSS
Figure 73. Negative Stress on a Standard Pad vs. VDD
VDD
VDD
(3a)
(2a)
(1)
OUT
(4)
IN
Main path
(3b)
VSS
114/135
(2b)
VSS
ST72104Gx-Auto, ST72215Gx-Auto, ST72216Gx-Auto, ST72254Gx-Auto
EMC CHARACTERISTICS (Cont’d)
True Open Drain Pin Protection
The centralized protection (4) is not involved in the
discharge of the ESD stresses applied to true
open drain pads due to the fact that a P-Buffer and
diode to VDD are not implemented. An additional
local protection between the pad and VSS (5a &
5b) is implemented to completely absorb the positive ESD discharge.
Multisupply Configuration
When several types of ground (VSS, VSSA, ...) and
power supply (VDD, VDDA, ...) are available for any
reason (better noise immunity...), the structure
shown in Figure 76 is implemented to protect the
device against ESD.
Figure 74. Positive Stress on a True Open Drain Pad vs. VSS
VDD
VDD
Main path
(1)
Path to avoid
OUT
(5a)
(4)
IN
(3b)
(5b)
(2b)
VSS
VSS
Figure 75. Negative Stress on a True Open Drain Pad vs. VDD
VDD
VDD
Main path
(1)
OUT
(3b)
(4)
IN
(3b)
(2b)
(3b)
VSS
VSS
Figure 76. Multisupply Configuration
VDD
VDDA
VDDA
VSS
BACK TO BACK DIODE
BETWEEN GROUNDS
VSSA
VSSA
115/135
ST72104Gx-Auto, ST72215Gx-Auto, ST72216Gx-Auto, ST72254Gx-Auto
13.8 I/O PORT PIN CHARACTERISTICS
13.8.1 General Characteristics
Subject to general operating conditions for VDD, fOSC, and TA unless otherwise specified.
Symbol
Parameter
Conditions
Min
Typ 1)
2)
VIL
Input low level voltage
VIH
Input high level voltage 2)
Vhys
Schmitt trigger voltage hysteresis 3)
Max
0.3xVDD
0.7xVDD
400
Input leakage current
VSS≤VIN≤VDD
±1
IS
Static current consumption 4)
Floating input mode
200
RPU
Weak pull-up equivalent resistor 5)
VIN=VSS
CIO
I/O pin capacitance
5
Output high to low level fall time 6)
25
VDD=5V
62
120
250
VDD=3.4V
170
200
300
tr(IO)out
CL=50pF
Output low to high level rise time 6) Between 10% and 90%
tw(IT)in
External interrupt pulse time 7)
25
1
V
mV
IL
tf(IO)out
Unit
µA
kΩ
pF
ns
tCPU
Figure 77. Two typical Applications with unused I/O Pin
VDD
ST72XXX
10kΩ
10kΩ
UNUSED I/O PORT
UNUSED I/O PORT
ST72XXX
Figure 78. Typical IPU vs. VDD with VIN=VSS
Ipu [µA]
70
60
Ta=-40°C
Ta=85°C
Ta=25°C
Ta=125°C
50
40
30
20
10
0
3.2
3.5
4
4.5
5
5.5
Vdd [V]
Notes:
1. Unless otherwise specified, typical data are based on TA=25°C and VDD=5V.
2. Data based on characterization results, not tested in production.
3. Hysteresis voltage between Schmitt trigger switching levels. Based on characterization results, not tested.
4. Configuration not recommended, all unused pins must be kept at a fixed voltage: using the output mode of the I/O for
example or an external pull-up or pull-down resistor (see Figure 77). Data based on design simulation and/or technology
characteristics, not tested in production.
5. The RPU pull-up equivalent resistor is based on a resistive transistor (corresponding IPU current characteristics described in Figure 78). This data is based on characterization results, tested in production at VDD max.
6. Data based on characterization results, not tested in production.
7. To generate an external interrupt, a minimum pulse width has to be applied on an I/O port pin configured as an external
interrupt source.
116/135
ST72104Gx-Auto, ST72215Gx-Auto, ST72216Gx-Auto, ST72254Gx-Auto
I/O PORT PIN CHARACTERISTICS (Cont’d)
13.8.2 Output Driving Current
Subject to general operating conditions for VDD, fOSC, and TA unless otherwise specified.
Symbol
Parameter
Conditions
Output low level voltage for a standard I/O pin
when 8 pins are sunk at same time
(see Figure 79 and Figure 82)
Output low level voltage for a high sink I/O pin
when 4 pins are sunk at same time
(see Figure 80 and Figure 83)
VOH
2)
Max
IIO=+5mA TA≤85°C
TA≥85°C
1.3
1.5
IIO=+2mA TA≤85°C
TA≥85°C
0.65
0.75
IIO=+20mA, TA≤85°C
TA≥85°C
1.5
1.7
IIO=+8mA TA≤85°C
TA≥85°C
0.75
0.85
Unit
V
IIO=-5mA, TA≤85°C VDD-1.6
TA≥85°C VDD-1.7
IIO=-2mA TA≤85°C VDD-0.8
TA≥85°C VDD-1.0
Output high level voltage for an I/O pin
when 4 pins are sourced at same time
(see Figure 81 and Figure 84)
Figure 79. Typical VOL at VDD=5V (standard)
Vol [V] at Vdd=5V
Figure 81. Typical VOH at VDD=5V
Voh [V] at Vdd=5V
2.5
6
Ta=-40°C
Ta=85°C
2
1.5
VDD=5V
VOL
1)
Min
5
Ta=25°C
Ta=125°C
4
1
3
Ta=-40°C
Ta=85°C
0.5
2
Ta=25°C
Ta=125°C
0
1
0
2
4
6
8
10
-8
-6
-4
-2
0
Iio [mA]
Iio [mA]
Figure 80. Typical VOL at VDD=5V (high-sink)
Vol [V] at Vdd=5V
2
Ta=-40°C
Ta=85°C
Ta=25°C
Ta=125°C
1.5
1
0.5
0
0
5
10
15
20
25
30
Iio [mA]
Notes:
1. The IIO current sunk must always respect the absolute maximum rating specified in Section 13.2.2 and the sum of IIO
(I/O ports and control pins) must not exceed IVSS.
2. The IIO current sourced must always respect the absolute maximum rating specified in Section 13.2.2 and the sum of
IIO (I/O ports and control pins) must not exceed IVDD. True open drain I/O pins does not have VOH.
117/135
ST72104Gx-Auto, ST72215Gx-Auto, ST72216Gx-Auto, ST72254Gx-Auto
I/O PORT PIN CHARACTERISTICS (Cont’d)
Figure 82. Typical VOL vs. VDD (standard I/Os)
Vol [V] at Iio=2mA
0.5
Ta=-40°C
Ta=85°C
Ta=25°C
Ta=125°C
0.45
0.4
0.35
0.3
0.25
0.2
3.2
3.5
4
4.5
5
Vol [V] at Iio=5mA
1.4
1.3
1.2
1.1
1
0.9
0.8
0.7
0.6
0.5
5.5
3.2
3.5
Ta=-40°C
Ta=85°C
Ta=25°C
Ta=125°C
4
Vdd [V]
4.5
5
5.5
Vdd [V]
Figure 83. Typical VOL vs. VDD (high-sink I/Os)
Vol [V] at Iio=8mA
Ta=-40°C
Ta=85°C
Ta=25°C
Ta=125°C
0.55
Vol [V] at Iio=20mA
Ta=-40°C
Ta=85°C
Ta=25°C
Ta=125°C
1.5
0.5
1.3
0.45
0.4
1.1
0.35
0.9
0.3
0.7
0.25
0.2
0.5
3.2
3.5
4
4.5
5
5.5
3.2
3.5
Vdd [V]
4
4.5
5
5.5
Vdd [V]
Figure 84. Typical VOH vs. VDD
Voh [V] at Iio=-2mA
Voh [V] at Iio=-5mA
5.5
5
5
4
4.5
3
4
3.5
Ta=-40°C
Ta=85°C
2
Ta=-40°C
Ta=85°C
Ta=25°C
Ta=125°C
1
Ta=25°C
Ta=125°C
3
2.5
2
0
3.2
3.5
4
4.5
Vdd [V]
118/135
5
5.5
3.5
4
4.5
Vdd [V]
5
5.5
ST72104Gx-Auto, ST72215Gx-Auto, ST72216Gx-Auto, ST72254Gx-Auto
13.9 CONTROL PIN CHARACTERISTICS
13.9.1 Asynchronous RESET Pin
Subject to general operating conditions for VDD, fOSC, and TA unless otherwise specified.
Symbol
Parameter
Conditions
Min
Typ 1)
2)
VIL
Input low level voltage
VIH
Input high level voltage 2)
Vhys
Schmitt trigger voltage hysteresis 3)
Max
Unit
0.3xVDD
400
4)
VOL
Output low level voltage
(see Figure 87, Figure 88)
VDD=5V
RON
Weak pull-up equivalent resistor 5)
VIN=VSS
tw(RSTL)out Generated reset pulse duration
th(RSTL)in
External reset pulse hold time 6)
tg(RSTL)in
Filtered glitch duration 7)
V
0.7xVDD
mV
IIO=+5mA
0.68
0.95
IIO=+2mA
0.28
0.45
VDD=5V
20
40
60
VDD=3.4V
80
100
120
External pin or
internal reset sources
6
30
V
kΩ
1/fSFOSC
µs
20
µs
100
ns
VDD
VDD
O
RON
USER
EXTERNAL
RESET
CIRCUIT 8)
0.1µF
ST72XXX
VDD
PT
IO
N
AL
Figure 85. Typical Application with RESET pin 8)
4.7kΩ
INTERNAL
RESET CONTROL
RESET
0.1µF
WATCHDOG RESET
LVD RESET
Notes:
1. Unless otherwise specified, typical data are based on TA=25°C and VDD=5V.
2. Data based on characterization results, not tested in production.
3. Hysteresis voltage between Schmitt trigger switching levels. Based on characterization results, not tested.
4. The IIO current sunk must always respect the absolute maximum rating specified in Section 13.2.2 and the sum of IIO
(I/O ports and control pins) must not exceed IVSS.
5. The RON pull-up equivalent resistor is based on a resistive transistor (corresponding ION current characteristics described in Figure 86). This data is based on characterization results, not tested in production.
6. To guarantee the reset of the device, a minimum pulse has to be applied to RESET pin. All short pulses applied on
RESET pin with a duration below th(RSTL)in can be ignored.
7. The reset network (the resistor and two capacitors) protects the device against parasitic resets, especially in a noisy
environments.
8. The output of the external reset circuit must have an open-drain output to drive the ST7 reset pad. Otherwise the device
can be damaged when the ST7 generates an internal reset (LVD or watchdog).
119/135
ST72104Gx-Auto, ST72215Gx-Auto, ST72216Gx-Auto, ST72254Gx-Auto
CONTROL PIN CHARACTERISTICS (Cont’d)
Figure 86. Typical ION vs. VDD with VIN=VSS
Figure 87. Typical VOL at VDD=5V (RESET)
Ion [µA]
Vol [V] at Vdd=5V
200
Ta=-40°C
Ta=85°C
Ta=25°C
Ta=125°C
Ta=-40°C
Ta=85°C
Ta=25°C
Ta=125°C
2
150
1.5
100
1
50
0.5
0
0
3.2
3.5
4
4.5
5
0
5.5
1
2
3
4
5
6
7
8
Iio [mA]
Vdd [V]
Figure 88. Typical VOL vs. VDD (RESET)
Vol [V] at Iio=2mA
Ta=-40°C
Ta=85°C
Vol [V] at Iio=5mA
Ta=-40°C
Ta=85°C
Ta=25°C
Ta=125°C
1.2
Ta=25°C
Ta=125°C
0.5
0.45
0.4
1
0.35
0.8
0.3
0.6
0.25
0.4
0.2
3.2
3.5
4
4.5
Vdd [V]
120/135
5
5.5
3.2
3.5
4
4.5
Vdd [V]
5
5.5
ST72104Gx-Auto, ST72215Gx-Auto, ST72216Gx-Auto, ST72254Gx-Auto
CONTROL PIN CHARACTERISTICS (Cont’d)
13.9.2 ISPSEL Pin
Subject to general operating conditions for VDD, fOSC, and TA unless otherwise specified.
Symbol
VIL
VIH
IL
Parameter
Input low level voltage 1)
Input high level voltage 1)
Input leakage current
Conditions
Min
VSS
VDD-0.1
VIN=VSS
Max
0.2
12.6
±1
Unit
V
µA
Figure 89. Two typical Applications with ISPSEL Pin 2)
ISPSEL
ST72XXX
ISPSEL
PROGRAMMING
TOOL
10kΩ
ST72XXX
Notes:
1. Data based on design simulation and/or technology characteristics, not tested in production.
2. When the ISP Remote mode is not required by the application ISPSEL pin must be tied to VSS.
121/135
ST72104Gx-Auto, ST72215Gx-Auto, ST72216Gx-Auto, ST72254Gx-Auto
13.10 TIMER PERIPHERAL CHARACTERISTICS
Subject to general operating conditions for VDD,
fOSC, and TA unless otherwise specified.
Refer to I/O port characteristics for more details on
the input/output alternate function characteristics
(output compare, input capture, external clock,
PWM output...).
13.10.1 Watchdog Timer
Symbol
tw(WDG)
Parameter
Watchdog time-out duration
Conditions
fCPU=8MHz
Min
Typ
Max
Unit
12,288
786,432
tCPU
1.54
98.3
ms
Max
Unit
13.10.2 16-Bit Timer
Symbol
Parameter
Conditions
tw(ICAP)in Input capture pulse time
tres(PWM) PWM resolution time
fCPU=8MHz
Min
Typ
1
tCPU
2
tCPU
250
ns
fEXT
Timer external clock frequency
0
fCPU/4
MHz
fPWM
PWM repetition rate
0
fCPU/4
MHz
16
bit
ResPWM PWM resolution
122/135
ST72104Gx-Auto, ST72215Gx-Auto, ST72216Gx-Auto, ST72254Gx-Auto
13.11 COMMUNICATION INTERFACE CHARACTERISTICS
13.11.1 SPI - Serial Peripheral Interface
Subject to general operating conditions for VDD,
fOSC, and TA unless otherwise specified.
Symbol
fSCK
1/tc(SCK)
tr(SCK)
tf(SCK)
tsu(SS)
th(SS)
tw(SCKH)
tw(SCKL)
tsu(MI)
tsu(SI)
th(MI)
th(SI)
ta(SO)
tdis(SO)
tv(SO)
th(SO)
tv(MO)
th(MO)
Parameter
Refer to I/O port characteristics for more details on
the input/output alternate function characteristics
(SS, SCK, MOSI, MISO).
Conditions
Master
fCPU=8MHz
Slave
fCPU=8MHz
SPI clock frequency
Min
fCPU/128
0.0625
0
SPI clock rise and fall time
Max
fCPU/4
2
fCPU/2
4
Unit
MHz
see I/O port pin description
SS setup time
SS hold time
Slave
Slave
Master
Slave
Master
Slave
Master
Slave
Slave
Slave
SCK high and low time
Data input setup time
Data input hold time
Data output access time
Data output disable time
Data output valid time
Data output hold time
Data output valid time
Data output hold time
120
120
100
90
100
100
100
100
0
Slave (after enable edge)
Master (before capture edge)
ns
120
240
120
0
0.25
0.25
tCPU
Figure 90. SPI Slave Timing Diagram with CPHA=0 3)
SS INPUT
SCK INPUT
tsu(SS)
tc(SCK)
th(SS)
CPHA=0
CPOL=0
CPHA=0
CPOL=1
ta(SO)
MISO OUTPUT
tw(SCKH)
tw(SCKL)
MSB OUT
see note 2
tsu(SI)
MOSI INPUT
tv(SO)
th(SO)
BIT6 OUT
tdis(SO)
tr(SCK)
tf(SCK)
LSB OUT
see
note 2
th(SI)
MSB IN
BIT1 IN
LSB IN
Notes:
1. Data based on design simulation and/or characterization results, not tested in production.
2. When no communication is on-going the data output line of the SPI (MOSI in master mode, MISO in slave mode) has
its alternate function capability released. In this case, the pin status depends on the I/O port configuration.
3. Measurement points are done at CMOS levels: 0.3xVDD and 0.7xVDD.
123/135
ST72104Gx-Auto, ST72215Gx-Auto, ST72216Gx-Auto, ST72254Gx-Auto
COMMUNICATION INTERFACE CHARACTERISTICS (Cont’d)
Figure 91. SPI Slave Timing Diagram with CPHA=1 1)
SS INPUT
tsu(SS)
tc(SCK)
th(SS)
SCK INPUT
CPHA=1
CPOL=0
CPHA=1
CPOL=1
tw(SCKH)
tw(SCKL)
ta(SO)
MISO OUTPUT
see
note 2
tv(SO)
th(SO)
MSB OUT
HZ
tsu(SI)
BIT6 OUT
LSB OUT
see
note 2
th(SI)
MSB IN
MOSI INPUT
tdis(SO)
tr(SCK)
tf(SCK)
BIT1 IN
LSB IN
Figure 92. SPI Master Timing Diagram 1)
SS INPUT
tc(SCK)
SCK INPUT
CPHA=0
CPOL=0
CPHA=0
CPOL=1
CPHA=1
CPOL=0
CPHA=1
CPOL=1
tw(SCKH)
tw(SCKL)
tsu(MI)
MISO INPUT
MOSI OUTPUT
th(MI)
MSB IN
tv(MO)
see note 2
tr(SCK)
tf(SCK)
BIT6 IN
LSB IN
th(MO)
MSB OUT
BIT6 OUT
LSB OUT
see note 2
Notes:
1. Measurement points are done at CMOS levels: 0.3xVDD and 0.7xVDD.
2. When no communication is on-going the data output line of the SPI (MOSI in master mode, MISO in slave mode) has
its alternate function capability released. In this case, the pin status depends of the I/O port configuration.
124/135
ST72104Gx-Auto, ST72215Gx-Auto, ST72216Gx-Auto, ST72254Gx-Auto
COMMUNICATION INTERFACE CHARACTERISTICS (Cont’d)
13.11.2 I2C - Inter IC Control Interface
Subject to general operating conditions for VDD,
fOSC, and TA unless otherwise specified.
Symbol
Refer to I/O port characteristics for more details on
the input/output alternate function characteristics
(SDAI and SCLI). The ST7 I2C interface meets the
requirements of the Standard I2C communication
protocol described in the following table.
Standard mode I2C
Parameter
Min 1)
Fast mode I2C
Max 1)
Min 1)
Max 1)
tw(SCLL)
SCL clock low time
4.7
1.3
tw(SCLH)
SCL clock high time
4.0
0.6
tsu(SDA)
SDA setup time
250
100
th(SDA)
SDA data hold time
0 3)
0 2)
900 3)
tr(SDA)
tr(SCL)
SDA and SCL rise time
1000
20+0.1Cb
300
tf(SDA)
tf(SCL)
SDA and SCL fall time
300
20+0.1Cb
300
Unit
µs
ns
th(STA)
START condition hold time
4.0
0.6
tsu(STA)
Repeated START condition setup time
4.7
0.6
tsu(STO)
STOP condition setup time
4.0
0.6
ns
4.7
1.3
ms
tw(STO:STA) STOP to START condition time (bus free)
Cb
Capacitive load for each bus line
µs
400
400
pF
Figure 93. Typical Application with I2C Bus and Timing Diagram 4)
VDD
4.7kΩ
I2 C
VDD
4.7kΩ
BUS
100Ω
SDAI
100Ω
SCLI
ST72XXX
REPEATED START
START
tsu(STA)
tw(STO:STA)
START
SDA
tr(SDA)
tf(SDA)
tsu(SDA)
STOP
th(SDA)
SCK
th(STA)
tw(SCKH)
tw(SCKL)
tr(SCK)
tf(SCK)
tsu(STO)
Notes:
1. Data based on standard I2C protocol requirement, not tested in production.
2. The device must internally provide a hold time of at least 300ns for the SDA signal in order to bridge the undefined
region of the falling edge of SCL.
3. The maximum hold time of the START condition has only to be met if the interface does not stretch the low period of
SCL signal.
4. Measurement points are done at CMOS levels: 0.3xVDD and 0.7xVDD.
125/135
ST72104Gx-Auto, ST72215Gx-Auto, ST72216Gx-Auto, ST72254Gx-Auto
13.12 8-BIT ADC CHARACTERISTICS
Subject to general operating conditions for VDD, fOSC, and TA unless otherwise specified.
Symbol
Parameter
fADC
ADC clock frequency
VAIN
Conversion range voltage 2)
Conditions
RAIN
External input resistor
Internal sample and hold capacitor
Max
Unit
4
MHz
VDDA
10
0
fCPU=8MHz, fADC=4MHz
- Sample capacitor loading time
- Hold conversion time
3)
6
Stabilization time after ADC enable
Conversion time (Sample+Hold)
tADC
Typ 1)
VSSA
CADC
tSTAB
Min
V
kΩ
pF
4)
µs
3
4
8
1/fADC
Figure 94. Typical Application with ADC
VDD
VT
0.6V
RAIN
AINx
VAIN
ADC
CIO
~2pF
VT
0.6V
IL
±1µA
VDD
VDDA
0.1µF
VSSA
ST72XXX
Notes:
1. Unless otherwise specified, typical data are based on TA=25°C and VDD-VSS=5V. They are given only as design guidelines and are not tested.
2. When VDDA and VSSA pins are not available on the pinout, the ADC refer to VDD and VSS.
3. Any added external serial resistor will downgrade the ADC accuracy (especially for resistance greater than 10kΩ). Data
based on characterization results, not tested in production.
4. The stabilization time of the AD converter is masked by the first tLOAD. The first conversion after the enable is then
always valid.
126/135
ST72104Gx-Auto, ST72215Gx-Auto, ST72216Gx-Auto, ST72254Gx-Auto
8-BIT ADC CHARACTERISTICS (Cont’d)
ADC Accuracy
Symbol
VDD=5V, 2)
fCPU=1MHz
Parameter
Min
|ET|
1)
Offset error
EG
Gain Error 1)
|ED|
|EL|
Max
Total unadjusted error 1)
EO
Differential linearity error
Integral linearity error
VDD=5.0V, 3)
fCPU=8MHz
1)
1)
Min
Max
VDD=3.3V, 3)
fCPU=8MHz
Min
Unit
Max
2.0
2.0
2.0
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
LSB
Figure 95. ADC Accuracy Characteristics
Digital Result ADCDR
EG
255
254
253
1LSB
IDEAL
V
–V
DDA
SSA
= ----------------------------------------256
(2)
ET
(3)
7
(1)
6
5
4
EO
EL
3
ED
2
(1) Example of an actual transfer curve
(2) The ideal transfer curve
(3) End point correlation line
ET=Total Unadjusted Error: maximum deviation
between the actual and the ideal transfer curves.
EO=Offset Error: deviation between the first actual
transition and the first ideal one.
EG=Gain Error: deviation between the last ideal
transition and the last actual one.
ED=Differential Linearity Error: maximum deviation
between actual steps and the ideal one.
EL=Integral Linearity Error: maximum deviation
between any actual transition and the end point
correlation line.
1 LSBIDEAL
1
0
1
VSSA
Vin (LSBIDEAL)
2
3
4
5
6
7
253 254 255 256
VDDA
Notes:
1. ADC Accuracy vs. Negative Injection Current:
For IINJ-=0.8mA, the typical leakage induced inside the die is 1.6µA and the effect on the ADC accuracy is a loss of 1 LSB
for each 10KΩ increase of the external analog source impedance. This effect on the ADC accuracy has been observed
under worst-case conditions for injection:
- negative injection
- injection to an Input with analog capability, adjacent to the enabled Analog Input
- at 5V VDD supply, and worst case temperature.
2. Data based on characterization results with TA=25°C.
3. Data based on characterization results over the whole temperature range.
127/135
ST72104Gx-Auto, ST72215Gx-Auto, ST72216Gx-Auto, ST72254Gx-Auto
14 PACKAGE CHARACTERISTICS
14.1 PACKAGE MECHANICAL DATA
Figure 96. 28-Pin Plastic Small Outline Package, 300-mil Width
Dim.
mm
Min
A
2.35
A1
B
Typ
inches
Max
Min
Typ
Max
2.65 0.0926
0.1043
0.10
0.30 0.0040
0.0118
0.33
0.51 0.013
0.020
C
0.23
0.32 0.0091
0.0125
D
17.70
18.10 0.6969
0.7125
E
7.40
e
7.60 0.2914
1.27
0.2992
0.0500
H
10.01
10.64 0.394
0.419
h
0.25
0.74 0.010
0.029
0.41
1.27 0.016
0.050
0.10
0.004
K
L
G
SO28
0°
8°
Number of Pins
N
28
14.2 ECOPACK®
In accordance with the RoHS European directive,
all STMicroelectronics packages have been converted to lead-free technology, named ECOPACK®.
– ECOPACK® packages are qualified according
to the JEDEC STD-020B compliant soldering
profile.
– Detailed information
on the STMicroelectronics ECOPACK® transition program is available on www.st.com/stonline/leadfree/, with
specific technical application notes covering
the main technical aspects related to lead-free
conversion (AN2033, AN2034, AN2035 and
AN2036).
14.3 THERMAL CHARACTERISTICS
Symbol
RthJA
PD
TJmax
Ratings
Value
Unit
Package thermal resistance (junction to ambient) SO28
75
°C/W
Power dissipation 1)
500
mW
150
°C
Maximum junction temperature
2)
Notes:
1. The power dissipation is obtained from the formula PD=PINT+PPORT where PINT is the chip internal power (IDDxVDD)
and PPORT is the port power dissipation determined by the user.
2. The average chip-junction temperature can be obtained from the formula TJ = TA + PD x RthJA.
128/135
ST72104Gx-Auto, ST72215Gx-Auto, ST72216Gx-Auto, ST72254Gx-Auto
15 DEVICE CONFIGURATION AND ORDERING INFORMATION
Each device is available for production in user programmable versions (Flash) as well as in factory
coded versions (ROM). Flash devices are shipped
to customers with a default content (FFh), while
ROM factory coded parts contain the code supplied by the customer. This implies that Flash devices have to be configured by the customer using
the Option Bytes while the ROM devices are factory-configured.
USER OPTION BYTE 1
Bit 7 = CFC Clock filter control on/off
This option bit enables or disables the clock filter
(CF) features.
0: Clock filter enabled
1: Clock filter disabled
Bit 6:4 = OSC[2:0] Oscillator selection
These three option bits can be used to select the
main oscillator as shown in Table 24.
Bit 3:2 = LVD[1:0] Low voltage detection selection
These option bits enable the LVD block with a selected threshold as shown in Table 25.
Bit 1 = WDG HALT Watchdog and halt mode
This option bit determines if a RESET is generated
when entering HALT mode while the Watchdog is
active.
0: No Reset generation when entering Halt mode
1: Reset generation when entering Halt mode
Bit 0 = WDG SW Hardware or software watchdog
This option bit selects the watchdog type.
0: Hardware (watchdog always enabled)
1: Software (watchdog to be enabled by software)
Table 24. Main Oscillator Configuration
15.1 OPTION BYTES
The two option bytes allow the hardware configuration of the microcontroller to be selected.
The option bytes have no address in the memory
map and can be accessed only in programming
mode (for example using a standard ST7 programming tool). The default content of the Flash is fixed
to FFh.
In masked ROM devices, the option bytes are
fixed in hardware by the ROM code (see option
list).
USER OPTION BYTE 0
Bit 7:2 = Reserved, must always be 1.
Bit 1 = EXTIT External Interrupt Configuration.
This option bit allows the external interrupt mapping to be configured as shown in Table 23.
Table 23. External Interrupt Configuration
External IT0
External IT1
EXTIT
Ports PA7-PA0
Ports PB7-PB0
Ports PC5-PC0
1
Ports PA7-PA0
Ports PC5-PC0
Ports PB7-PB0
0
Selected Oscillator
External Clock (Standby)
1
1
1
~4 MHz Internal RC
1
1
0
1~14 MHz External RC
1
0
X
Low Power Resonator (LP)
0
1
1
Medium Power Resonator (MP)
0
1
0
Medium Speed Resonator (MS)
0
0
1
High Speed Resonator (HS)
0
0
0
Table 25. LVD Threshold Configuration
Configuration
Bit 0 = FMP Full memory protection.
This option bit enables or disables external access
to the internal program memory (readout protection). Clearing this bit causes the erasing (by overwriting with the currently latched values) of the
whole memory (not including the option bytes).
0: Program memory not readout protected
1: Program memory readout protected
Default
Value
1
1
1
Highest Voltage Threshold (∼4.50V)
1
0
Medium Voltage Threshold (∼4.05V)
0
1
Lowest Voltage Threshold (∼3.45V)
0
0
USER OPTION BYTE 1
0
1
1
1
1
1
0
0
7
EXTIT FMP CFC
1
LVD1 LVD0
LVD Off
USER OPTION BYTE 0
7
Reserved
OSC2 OSC1 OSC0
1
OSC OSC OSC
WDG WDG
LVD1 LVD0
2
1
0
HALT SW
1
1
0
1
1
1
1
129/135
ST72104Gx-Auto, ST72215Gx-Auto, ST72216Gx-Auto, ST72254Gx-Auto
15.2 DEVICE ORDERING INFORMATION AND TRANSFER OF CUSTOMER CODE
Customer code is made up of the ROM contents
and the list of the selected options (if any). The
ROM contents are to be sent on diskette, or by
electronic means, with the S19 hexadecimal file
generated by the development tool. All unused
bytes must be set to FFh.
The selected options are communicated to
STMicroelectronics using the correctly completed
OPTION LIST appended.
The STMicroelectronics Sales Organization will be
pleased to provide detailed information on contractual points.
Figure 97. ROM Factory Coded Device Types
DEVICE PACKAGE TEMP. RANGE / XXX
Code name (defined by STMicroelectronics)
A = -40 to +85°C
B = -40 to +105°C
C = -40 to +125°C
M = Plastic SOIC
ST72104G1, ST72104G2,
ST72215G2, ST72216G1,
ST72254G1, ST72254G2
Figure 98. Flash User Programmable Device Types
DEVICE PACKAGE TEMP. RANGE
A = -40 to +85°C
B = -40 to +105°C
C = -40 to +125°C
M = Plastic SOIC
ST72C104G1, ST72C104G2,
ST72C215G2, ST72C216G1,
ST72C254G1, ST72C254G2
130/135
ST72104Gx-Auto, ST72215Gx-Auto, ST72216Gx-Auto, ST72254Gx-Auto
TRANSFER OF CUSTOMER CODE (Cont’d)
MICROCONTROLLER OPTION LIST
Customer
Address
Contact
Phone No
Reference
.....................................................................
.....................................................................
.....................................................................
.....................................................................
.....................................................................
.....................................................................
Device:
[ ] ST72104G1 (4KB)
[ ] ST72104G2 (8KB)
[ ] ST72215G2 (4KB)
[ ] ST72216G1 (8KB)
[ ] ST72254G1 (4KB)
[ ] ST72254G2 (8KB)
Package:
[ ] SO28
[ ] Tape & Reel
[ ] Tube
Marking:
[ ] Standard Marking
[ ] Special Marking SO28 (max. 13 Chars.):
_____________
Authorized characters are letters, digits, ‘.’, ‘-’, ‘/’ and spaces only. Please consult your local STMicroelectronics sales office for other marking details if required.
External Interrupt:
[ ] IT0 interrupt vector Port A, IT1 interrupt vector Port B & C
[ ] IT0 interrupt vector Port A & C, IT1 interrupt vector Port B
Temperature Range:
[ ] -40°C to +85°C
Clock Source Selection:
[ ] Resonator:
[ ] RC Network:
[ ] -40°C to +105°C
[ ] -40°C to +125°C
[ ] LP: Low power resonator (1 to 2 MHz)
[ ] MP: Medium power resonator (2 to 4 MHz)
[ ] MS: Medium speed resonator (4 to 8 MHz)
[ ] HS: High speed resonator (8 to 16 MHz)
[ ] Internal
[ ] External
[ ] External Clock
Clock Security System:
[ ] Disabled
[ ] Enabled
Watchdog Selection:
Halt when Watchdog on:
[ ] Software Activation
[ ] Reset
[ ] Hardware Activation
[ ] No reset
Readout Protection:
[ ] Disabled
[ ] Enabled
LVD Reset
[ ] Disabled
[ ] Enabled:
[ ] Highest threshold
[ ] Medium threshold
[ ] Lowest threshold
Comments : . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Supply Operating Range in the application: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Notes:
..........................................................................
Signature:
..........................................................................
131/135
ST72104Gx-Auto, ST72215Gx-Auto, ST72216Gx-Auto, ST72254Gx-Auto
15.3 DEVELOPMENT TOOLS
STmicroelectronics offers a range of hardware
and software development tools for the ST7 microcontroller family. Full details of tools available for
the ST7 from third party manufacturers can be obtained from the STMicroelectronics Internet site.
Third Party Tools
■ ACTUM
■ BP
■ COSMIC
■ CMX
■ DATA I/O
■ HITEX
■ HIWARE
■ ISYSTEM
■ KANDA
■ LEAP
Tools from these manufacturers include C compliers, emulators and gang programmers.
STMicroelectronics Tools
Three types of development tool are offered by
ST; all of them connect to a PC via a parallel (LPT)
port (see Table 26 and Table 27 for more details).
Table 26. STMicroelectronics Tool Features
Tool
ST7 Development Kit
ST7 HDS2 Emulator
ST7 Programming Board
In-Circuit Emulation
Programming Capability1)
Yes. (Same features as
HDS2 emulator but without Yes (DIP packages only)2)
logic analyzer)
Yes, powerful emulation
No
features including trace/
logic analyzer
No
Yes (All packages)
Software Included
ST7 CD ROM with:
– ST7 Assembly toolchain
– STVD7 and WGDB7 powerful
Source Level Debugger for Win
3.1, Win 95 and NT
– C compiler demo versions
– ST Realizer for Win 3.1 and
Win95
– Windows Programming Tools
for Win 3.1, Win 95 and NT
Notes:
1. In-Situ Programming (ISP) interface for Flash devices.
2. Tool equipped with a DIP socket only; an adapter may be required to program devices in SO packages.
Table 27. Dedicated STMicroelectronics Development Tools
Supported Products
ST72254G1, ST72C254G1
ST72254G2, ST72C254G2
ST72215G2, ST72C215G2
ST72216G1, ST72C216G1
ST72104G1, ST72C104G1,
ST72104G2, ST72C104G2
132/135
ST7 Development Kit
ST7 HDS2 Emulator
ST7MDT1-DVP2
ST7MDT1-EMU2B
ST7 Programming Board
ST7MDT1-EPB2/EU
ST7MDT1-EPB2/US
ST7MDT1-EPB2/UK
ST72104Gx-Auto, ST72215Gx-Auto, ST72216Gx-Auto, ST72254Gx-Auto
DEVELOPMENT TOOLS (Cont’d)
15.3.1 Package/Socket Footprint Proposal
Table 28. Suggested List of SO28 Socket Types
Package / Probe
SO28
EMU PROBE
Adaptor / Socket Reference
Same
Footprint
Socket Type
ENPLAS
OTS-28-1.27-04
Open Top
YAMAICHI
IC51-0282-334-1
Clamshell
Adapter from SO28 to SDIP32 footprint (delivered with emulator)
X
SMD to SDIP
15.4 ST7 APPLICATION NOTES
All relevant ST7 application notes can be found on
www.st.com.
133/135
ST72104Gx-Auto, ST72215Gx-Auto, ST72216Gx-Auto, ST72254Gx-Auto
16 SUMMARY OF CHANGES
Description of the changes between the current release of the specification and the previous one.
Date
Rev.
Main changes
Initial release of the ST72104Gx-Auto, ST72215Gx-Auto, ST72216Gx-Auto, ST72254Gx-Auto
datasheet
29-Oct-2007
134/135
1
The ST72xxxG-Auto datasheet was created from the ST72104G, ST72215G, ST72216G,
ST72254G Preliminary Data datasheet, revision 2.6 dated November 2000, with the following
changes:
Changed document title and description on page 1
Removed SDIP32 package outline from page 1
“Device Summary” on page 1:
- changed operating temperature range
- removed SDIP32 package
Section 1 "INTRODUCTION" on page 6: Added ‘-Auto’ extension to ST72xxxG numbers in first
paragraph
Section 2 "PIN DESCRIPTION" on page 7: Removed Figure "32-Pin SDIP Package Pinout"
Table 1 on page 8: Removed SDIP32 pin number column
Section 6 "SUPPLY, RESET AND CLOCK MANAGEMENT" on page 17: Added ‘-Auto’ extension to ST72xxxG numbers in first paragraph
“MULTI-OSCILLATOR (MO)” on page 21: Modified description of external and internal RC
Section 11.1.3 "Functional Description" on page 39: Replaced 500ns with 30µs at end of second paragraph to be in line with spec given in Section 13.9.1 "Asynchronous RESET Pin" on
page 119
Section 12.1.4 "Indexed (No Offset, Short, Long)" on page 90: Replaced “The indirect addressing mode consists of” with “The indexed addressing mode consists of” in second paragraph
Section 13.2.1 "Voltage Characteristics" on page 96: Changed VIN ratings and values
Section 13.3.1 "General Operating Conditions" on page 97: Modified ambient temperature
range conditions to include only automotive device suffix versions
Section 13.5.3.2 "Typical Ceramic Resonators" on page 106: Removed Table “Typical Ceramic Resonators for General Purpose Applications”
Changed titles of Figure 81 on page 117 and Figure 84 on page 118
Figure 91.SPI Slave Timing Diagram with CPHA=1 1): Corrected ‘CPHA=0’ to read ‘CPHA=1’
for SCKINPUT
Section 14.1 "PACKAGE MECHANICAL DATA" on page 128:
- removed Figure “32-Pin Shrink Plastic Dual In Line Package”
- added Section 14.2 "ECOPACK®" on page 128
- removed Section "SOLDERING AND GLUEABILITY INFORMATION"
Section 14.3 "THERMAL CHARACTERISTICS" on page 128: Removed SDIP32 package
from package thermal resistance ratings
Figure 97.ROM Factory Coded Device Types: Modified to include only automotive device temperature versions and removed DIP package
Figure 98.Flash User Programmable Device Types: Modified to include only automotive device temperature versions and removed DIP package
Section 15.1 "OPTION BYTES" on page 129: Changed description of FMP option bit
“MICROCONTROLLER OPTION LIST” on page 131: Modified to include only automotive device temperature versions and removed DIP package
Section 15.3 "DEVELOPMENT TOOLS" on page 132: Removed link ‘http//mcu.st.com’ from
the end of the first paragraph
Table 26, “STMicroelectronics Tool Features,” on page 132: Added footnote 2
Section 15.3.1 "Package/Socket Footprint Proposal" on page 133: Removed Table “Suggested List of SDIP32 Socket Types”
Section 15.4 "ST7 APPLICATION NOTES" on page 133: Removed Table “ST7 Application
Notes”
Updated disclaimer on last page to include a mention about the use of ST products in automotive applications
ST72104Gx-Auto, ST72215Gx-Auto, ST72216Gx-Auto, ST72254Gx-Auto
Please Read Carefully:
Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the
right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any
time, without notice.
All ST products are sold pursuant to ST’s terms and conditions of sale.
Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no
liability whatsoever relating to the choice, selection or use of the ST products and services described herein.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this
document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products
or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such
third party products or services or any intellectual property contained therein.
UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED
WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS
OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.
UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT
RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE
SUSTAINING APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN
PERSONAL INJURY, DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT
SPECIFIED AS "AUTOMOTIVE GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK.
Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void
any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any
liability of ST.
ST and the ST logo are trademarks or registered trademarks of ST in various countries.
Information in this document supersedes and replaces all information previously supplied.
The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.
© 2007 STMicroelectronics - All rights reserved
STMicroelectronics group of companies
Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America
www.st.com
135/135