STMICROELECTRONICS STCF03I

STCF03I
High power white LED driver with I2C™ interface
Features
■
Buck-boost DC/DC converter
■
Drives one power white led up to:
800 mA between 3.3 V to 5.5 V
600 mA between 2.7 V to 5.5 V
■
Efficiency up to 92%
■
Output current control
■
1.8 MHz typ fixed frequency PWM
■
Synchronous rectification
■
Full I2C control
Applications
■
Operational modes:
Shutdown mode
■
Cell phone and smart phones
■
Camera flashes/strobe
■
Ready mode + auxiliary red led
Ready mode + NTC
Flash mode: up to 800 mA
Torch mode: up to 200 mA
■
PDAs and digital still cameras
TFBGA25 (3x3)
Description
■
Soft and hard triggering of flash
■
Flash and torch dimming with 16 exponential
values
■
Dimmable red led indicator auxiliary output
■
Internally or externally timed flash operation
■
Digitally programmable safety time-out in flash
mode
■
LED overtemperature detection and protection
with external NTC resistor
The STCF03I is a high efficiency power supply
solution to drive a single flash LED in camera
phone, PDAs and other hand-held devices. It is a
buck - boost converter to guarantee a proper LED
current control over all possible conditions of
battery voltage and output voltage; the output
current control ensures a good current regulation
over the forward voltage spread characteristics of
the Flash LED.
■
Opened and shorted led failure detection and
protection
■
Chip over temperature detection and protection
■
< 1 µA Shutdown current
■
Package (3x3 mm) TFBGA25
Thanks to the high efficiency of the converter, the
input current taken from the battery remains
under 1.5 A. All the functions of the device are
controlled through the I2C bus which helps to
reduce logic pins on the package and to save
PCB tracks on the board. (See continuous
description)
Table 1. Device summary
Order code
Package
Packaging
STCF03ITBR
TFBGA25 (3x3 mm)
3000 parts per reel
September 2007
Rev. 4
1/33
www.st.com
33
STCF03I
Contents
1
Description (continued) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2
Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
3
Pin configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
4
Maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
5
Application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
6
Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
7
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
8
2/33
7.1
Buck-Boost converter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
7.2
Logic pin description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
7.2.1
SCL, SDA pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
7.2.2
TRIG pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
7.2.3
ATN pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
7.2.4
ADD pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
7.2.5
TMSK pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
2
7.3
I C BUS interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
7.4
Data validity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
7.5
Start and stop conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
7.6
Byte format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
7.7
Acknowledge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
7.8
Writing to a single register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
7.9
Interface protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
7.10
Writing to multiple registers with incremental addressing . . . . . . . . . . . . 18
7.11
Reading from a single register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
7.12
Reading from multiple registers with incremental addressing . . . . . . . . . 19
Description of internal registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
8.1
PWR_ON . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
8.2
TRIG_EN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
STCF03I
9
8.3
TCH_ON . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
8.4
NTC_ON . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
8.5
FTIM_0~3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
8.6
TDIM_0~3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
8.7
FDIM_0~3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
8.8
AUXI_0~3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
8.9
AUXT_0~3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
8.10
F_RUN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
8.11
LED_F . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
8.12
NTC_W . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
8.13
NTC_H . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
8.14
OT_F . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
8.15
VOUTOK_N . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Detailed description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
9.1
PowerON reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
9.2
Shutdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
9.3
Ready mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
9.4
Single or multiple Flash using external (µP) temporization . . . . . . . . . . . 25
9.5
External (µP) temporization using TRIG_EN bit . . . . . . . . . . . . . . . . . . . . 26
9.6
Single Flash using internal temporization . . . . . . . . . . . . . . . . . . . . . . . . 26
9.7
Multiple Flash using internal temporization . . . . . . . . . . . . . . . . . . . . . . . 26
10
Typical performance characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
11
Package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
12
Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
3/33
List of figures
STCF03I
List of figures
Figure 1.
Figure 2.
Figure 3.
Figure 4.
Figure 5.
Figure 6.
Figure 7.
Figure 8.
Figure 9.
Figure 10.
Figure 11.
Figure 12.
Figure 13.
Figure 14.
Figure 15.
Figure 16.
Figure 17.
Figure 18.
Figure 19.
Figure 20.
Figure 21.
Figure 22.
4/33
Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Pin connections (bottom view) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Application schematic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Data validity on the I2C Bus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Timing diagram on I2C Bus. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Bit transfer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Acknowledge on I2C Bus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Writing to a single register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Writing to multiple registers with incremental addressing . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Reading from a single register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Reading from multiple registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Flash and Torch current vs. dimming value . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
VOUTOK_N behavior . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Flash current vs F_DIMM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Torch current vs T_DIMM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Aux current vs AUXI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Flash current vs temp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
VFB2 Flash vs temp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
IQ vs temp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Efficiency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Start-Up in Flash Mode 800 mA at VI = 3.6 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Line transient in Flash Mode 800 mA, change of VI from 2.7 V to 3.3 V in 10 µs. . . . . . . . 28
List of tables
STCF03I
List of tables
Table 1.
Table 2.
Table 3.
Table 4.
Table 5.
Table 6.
Table 7.
Table 8.
Table 9.
Table 10.
Table 11.
Table 12.
Table 13.
Table 14.
Table 15.
Table 16.
Table 17.
5/33
Device summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Pin description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Absolute maximum ratings (see note) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Thermal data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
List of external components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Electrical characteristics
(TJ = 25°C, VI = 3.6 V, 2xCI = 10 µF, CO = 1 µF, L = 4.7 µH, RFL = 0.27 Ω, RTR = 1.8 Ω,
RX = 15 KΩ, Typ. values @25°C, unless otherwise specified). . . . . . . . . . . . . . . . . . . . . . 11
Address table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Interface protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
I2C Register mapping function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Command register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Dimming register. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Auxiliary register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Auxiliary led dimming table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Torch Mode and Flash Mode dimming registers settings . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Status register. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Status register details . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Description (continued)
1
STCF03I
Description (continued)
Hard and soft-triggering of Flash are both supported. The device includes many functions to
protect the chip and the power LED, such as: a soft start control, chip over temperature
detection and protection, as well as opened and shorted LED detection and protection.
Besides, a digital programmable Time Out function protects the LED in case of a wrong
command from the µP. An optional external NTC resistor is supported to protect the LED
against over heating. In mobile phone applications, it is possible to reduce immediately the
Flash LED current during the signal transmission using the TMSK pin. This saves battery life
and gives more priority to supply RF transmission instead of flash function.
It is possible by I2C to separately program the current intensity in FLASH and TORCH
MODE using exponential steps. An auxiliary output can control an optional red LED to be
used as a recording indicator.
The device is packaged in 3x3 mm µTFBGA25 with a height less than 1 mm.
6/33
Diagram
STCF03I
2
Diagram
Figure 1.
Block diagram
NTC_REF
7/33
Pin configuration
STCF03I
3
Pin configuration
Figure 2.
Pin connections (bottom view)
Table 2. Pin description
8/33
Pin n°
Symbol
Description
E1,D2
VLX2
B3
RX
D1,C2
VOUT
A4
NTC
NTC resistor connection
B5
FB1
Feedback pin [ILED*(RFL+RTR)]
A5
FB2
RTR bypass
B4
FB2S
Feedback pin [ILED*RFL]
E2
GND
Signal ground
C5
TMSK
TX mask input.
D5
AUXL
Auxiliary LED output
D4
ADD
I2C address selection
A3
VBAT
Supply voltage
B1,C1
PVBAT
Power supply voltage
A2
VLX1A
Inductor connection
A1,B2
VLX1B
Inductor connection
E4
ATN
Attention (open drain output, active LOW)
E3
SDA
I2C data
C3,D3
PGND
E5
SCL
I2C clock signal
C4
TRIG
Flash trigger input
Inductor connection
Rx resistor connection
Output voltage
Power ground
Maximum ratings
4
STCF03I
Maximum ratings
Table 3. Absolute maximum ratings (see note)
Symbol
Parameter
Value
Unit
VBAT
Signal supply voltage
-0.3 to 6
V
PVBAT
Power supply voltage
-0.3 to 6
V
VLX1A, VLX1B
Inductor connection 1
–0.3 to VI+0.3
V
VLX2
Inductor connection 2
–0.3 to VO+0.3
V
VOUT
Output Voltage
-0.3 to 6
V
AUXL
Auxiliary LED
–0.3 to VI+0.3
V
-0.3 to 3
V
-0.3 to VI+0.3
V
Connection for reference resistor
-0.3 to 3
V
Connection for LED Temperature sensing
-0.3 to 3
V
±2
kV
800
mW
Operating junction temperature range
-40 to 85
°C
Junction temperature
-40 to 150
°C
Storage temperature range
-65 to 150
°C
FB1, FB2, FB2S
Feedback and sense voltage
SCL, SDA, TRIG,
ATN, ADD TMSK
Logic pin
RX
NTC
ESD
Human body model
PTOT (BGA)
TOP
TJ
TSTG
(1)
Continuous power dissipation (at TA=70°C)
1. Power dissipation is related parameter to used PCB. The recommended PCB design is included in the application note.
Note:
Absolute Maximum Ratings are those values beyond which damage to the device may
occur. Functional operation under these condition is not implied.
Table 4. Thermal data
Symbol
RthJA
9/33
Parameter
Thermal resistance junction-ambient
Value
Unit
150
°C/W
Application
STCF03I
5
Application
Figure 3.
Application schematic
**: Connect to VI, or GND or SDA or SCL to choose one of the 4 different I2C Slave Addresses.
***: Optional components to support auxiliary functions.
Table 5. List of external components
Component
Manufacturer
Part number
Value
Size
CI
TDK
X5R0J106M
10 µF
0603
CO
TDK
X5R0J105M
1 µF
0603
L (IFLASH = 0.5A)
TDK
VLF3012ST-4R7MR91
4.7 µH
2.6 x 2.8 x 1.2mm
L (IFLASH = 0.8A)
TDK
VLF4012AT-4R7M1R1
4.7 µH
3.7 x 3.5 x 1.2mm
NTC
Murata
NCP21WF104J03RA
100kΩ
0805
RFL
0.27Ω
0603
RTR
1.8Ω
0402
RX
15kΩ
0402
LED
Note:
10/33
Luxeon LED
LXCL-PW1
All of the above listed components refer to typical application. Operation of the STCF03I is
not limited to the choice of these external components.
Electrical characteristics
6
STCF03I
Electrical characteristics
Table 6. Electrical characteristics
(TJ = 25°C, VI = 3.6 V, 2xCI = 10 µF, CO = 1 µF, L = 4.7 µH, RFL = 0.27 Ω, RTR = 1.8 Ω, RX = 15 KΩ,
Typ. values @25°C, unless otherwise specified).
Symbol
Parameter
VI
Input operation supply voltage
VPW_ON
Test condition
Min.
Typ.
2.7
Max.
Unit
5.5
V
Power ON reset threshold
VI rising
2.3
V
Output current adjustment
range IFLASH
FLASH MODE for VI = 3.3 V to 5.5 V
60
800
FLASH MODE for VI = 2.7 V to 3.3 V
60
600
Output current adjustment
range ITORCH
Torch mode VI = 2.7 V to 5.5 V
15
200
Auxiliary LED output current
adjustment range IAUXLED
Ready mode, VI = 3.3 V to 5.5 V
0
20
2.5
5.3
V
RESET
IO
mA
VO
Regulated voltage range
FB1
Feedback voltage
Torch mode
30
250
mV
FB2
Feedback voltage
Flash mode
30
250
mV
ΔIO
Output current tolerance
Flash mode, IO = 160 mV/RFL
-10
10
%
RON_
FB1-FB2 ON resistance
Torch mode, IO = 200 mA
IQ
90
mΩ
Quiescent current in
SHUTDOWN mode
1
µA
Quiescent current in
Ready -mode
1.8
mA
fs
Frequency
VI = 2.7 V
1.8
MHz
ν
Efficiency of the chip itself
VI = 3.2 to 4.2 V, Flash Mode,
IO = 800 mA
87
%
Efficiency of the whole
application
VI = 3.2 to 4.2 V, Flash Mode,
IO = 800 mA, VO=VfLED_max + VFB2 =
5.02 V
See the typical application schematic
It is included losses of inductor and
sensing resistor
76
OVP
OVHYST
Output over voltage protection VI = 5.5 V, No Load
5.5
V
Over voltage hysteresis
VI = 5.5 V, No Load
0.3
V
OTP
Over temperature protection
VI = 5.5 V
140
°C
OTHYST
Over temperature hysteresis
VI = 5.5 V
20
°C
RONT1
RX-NTC switch On resistance Ready mode
25
Ω
NTCLEAK
11/33
RX-NTC switch OFF leakage
Shutdown mode, VNTC = 2 V
VRX = GND
1
µA
Electrical characteristics
STCF03I
Table 6. Electrical characteristics
(TJ = 25°C, VI = 3.6 V, 2xCI = 10 µF, CO = 1 µF, L = 4.7 µH, RFL = 0.27 Ω, RTR = 1.8 Ω, RX = 15 KΩ,
Typ. values @25°C, unless otherwise specified).
Symbol
Parameter
Test condition
Min.
NTC_REF NTC reference voltage
Typ.
Max.
1.8
Unit
V
VOL
Output logic signal level low
ATN
IOL = 10 mA
0.2
V
IOZ
Output logic leakage current
ATN
VOZ = 3.3 V
1
mA
VIL
Input Logic signal level SCL,
SDA, TRIG, TEST, ADD
VI = 2.7 V to 5.5 V
0
0.4
V
1.4
3
VIH
TON
Note:
12/33
LED current rise time
ILED = 0 to ILED = max
Typical value, not production tested.
2
ms
Introduction
7
STCF03I
Introduction
The STCF03I is a buck-boost converter, dedicated to power and control the current of a
Power White LED in a camera cell phone. The device operates at a constant switching
frequency of 1.8 MHz typ. It provides an output voltage down to 2.5 V and up to 5.3 V, from
a 2.7 V to 5.5 V supply voltage. This supply range allows operation from a single cell
Lithium-Ion battery. The I2C bus is used to control the device operation and for diagnostic
purposes. The current in Torch mode is adjustable from 15 mA to 200 mA. Flash mode
current is adjustable up to 800mA for an input voltage ranging from 3.3 V to 5.5 V and up to
600mA for an input voltage ranging from 2.7 V to 5.5 V. The Aux LED current can be
adjusted from 0 to 20 mA. The device uses an external NTC resistor to sense the
temperature of the white LED. These two last functions may not be needed in all
applications, and in these cases the relevant external components can be omitted.
7.1
Buck-Boost converter
The regulation of the PWM controller is done by sensing the current of the LED through
external sensing resistors (RFL and RTR, see application schematic). Depending on the
forward voltage of the Flash LED, the device automatically can change the operation mode
between buck (step down) and boost (step up) mode.
Three cases can occur: Boost region (VO > VBAT): this configuration is used in most cases,
as the output voltage VO = VfLED + ILED x RFL) is higher than VBAT; Buck region (VO < VBAT);
Buck / Boost region (VO ~ VBAT).
7.2
Logic pin description
7.2.1
SCL, SDA pins
These are the standard Clock and Data pins as defined in the I2C bus specification. External
pull-up is required according to I2C bus specifications. The recommended maximum voltage
of these signals should be 3.0 V.
7.2.2
TRIG pin
This input pin is internally AND-ed with the TRIG_EN bit to generate the internal signal that
activates the flash operation. This gives to the user the possibility to accurately control the
flash duration using a dedicated pin, avoiding the I2C bus latencies (hard-triggering). No
internal pull-up nor pull-down is provided.
7.2.3
ATN pin
This output pin (open-drain, active LOW) is provided to better manage the information
transfer from the STCF03I to the µP. Because of the limitations of a Single Master I2C bus
configuration, the µP should regularly poll the STCF03I to verify if certain operations have
been completed, or to check diagnostic information. Alternatively, the µP can use the ATN
pin to be advised that new data are available in the STAT_REG, thus avoiding continuous
polling. Then the information can be read in the STAT_REG by a read operation via I2C that,
besides, automatically resets the ATN pin. The STAT_REG bits affecting the ATN pin status
are mapped in Table 16. No internal pull-up is provided.
13/33
Introduction
7.2.4
STCF03I
ADD pin
With this pin it is possible to select one of the 4 possible I2C slave addresses. No internal
pull-up nor pull-down is provided. The pin has to be connected to either GND, VI, SCL or
SDA to select the desired I2C slave address (see Table 7)
Table 7. Address table
ADD pin
A7
A6
A5
A4
A3
A2
A1
A0
GND
0
1
1
0
0
0
0
R/W
VBAT
0
1
1
0
0
0
1
R/W
SDAL
0
1
1
0
0
1
0
R/W
SCL
0
1
1
0
0
1
1
R/W
It is necessary to keep SCL and SDA high during power on reset, otherwise the I2C device
address may be recognized improperly.
7.2.5
TMSK pin
This pin can be used to implement the TX masking function. This function has effect only for
Flash current settings higher than 200 mA (bit FDIM_3=1). Under this condition, when this
pin is pulled high by the µP, the current flowing in the LED is forced at 200 mA typ. No
internal pull-up nor pull-down is provided; to be externally wired to GND if TX masking
function is not used.
7.3
I2C BUS interface
Data transmission from the main µP to STCF03I and vice versa takes place through the 2
I2C bus interface wires, consisting of the two lines SDA and SCL (pull-up resistors to a
positive supply voltage must be externally connected). The recommended maximum voltage
of these signals should be 3.0 V.
14/33
Introduction
7.4
STCF03I
Data validity
As shown in Figure 4, the data on the SDA line must be stable during the high period of the
clock. The HIGH and LOW state of the data line can only change when the clock signal on
the SCL line is LOW.
Figure 4.
Data validity on the I2C Bus
7.5
Start and stop conditions
Both DATA and CLOCK lines remain HIGH when the bus is not busy. As shown in Figure 5,
a start condition is a HIGH to LOW transition of the SDA line while SCL is HIGH. The stop
condition is a LOW to HIGH transition of the SDA line while SCL is HIGH. A STOP condition
must be sent before each START condition.
Figure 5.
Timing diagram on I2C Bus
7.6
Byte format
Every byte transferred to the SDA line must contain 8 bits. Each byte must be followed by an
acknowledge bit. The MSB is transferred first. One data bit is transferred during each clock
15/33
Introduction
STCF03I
pulse. The data on the SDA line must remain stable during the HIGH period of the clock
pulse. Any change in the SDA line at this time will be interpreted as a control signal.
Figure 6.
Bit transfer
7.7
Acknowledge
The master (µP) puts a resistive HIGH level on the SDA line during the acknowledge clock
pulse (see Figure 7). The peripheral (STCF03I) that acknowledges has to pull-down (LOW)
the SDA line during the acknowledge clock pulse, so that the SDA line is stable LOW during
this clock pulse. The peripheral which has been addressed has to generate an acknowledge
pulse after the reception of each byte, otherwise the SDA line remains at the HIGH level
during the ninth clock pulse duration. In this case, the master transmitter can generate the
STOP information in order to abort the transfer.
Figure 7.
16/33
Acknowledge on I2C Bus
Introduction
STCF03I
Table 8. Interface protocol
Device address + R/W bit
7
6
5
4
3
S M
T S
A B
R
T
7.8
2
1
0
Register address
7
6
5
4
3
2
Data
1
L R A M
S W C S
B
K B
0
7
L
S
B
A M
C S
K B
6
5
4
3
2
1
0
L
S
B
A
C
K
S
T
O
P
Writing to a single register
Writing to a single register starts with a START bit followed by the 7 bit device address of
STCF03I. The 8th bit is the R/W bit, which is 0 in this case. R/W = 1 means a reading
operation. Then the master waits for an acknowledge from STCF03I. Then the 8 bit address
of register is sent to STCF03I. It is also followed by an acknowledge pulse. The last
transmitted byte is the data that is going to be written to the register. It is again followed by
an acknowledge pulse from STCF03I. The master then generates a STOP bit and the
communication is over. See Figure 8 below.
Figure 8.
Writing to a single register
DEVICE
ADDRESS
7 bits
S M
T S
A B
R
T
7.9
W
R
I
T
E
ADDRESS OF
REGISTER
L R A M
S / C S
B W K B
DATA
L A M
S C S
B K B
SDA LINE
Interface protocol
The interface protocol is composed of (Table 8):
- A start condition (START)
- A Device address + R/W bit (read =1 / write =0)
- A Register address byte
- A sequence of data n* (1 byte + acknowledge)
- A stop condition (STOP)
17/33
L A S
S C T
B K O
P
Introduction
STCF03I
The Register address byte determines the first register in which the read or write operation
takes place. When the read or write operation is finished, the register address is
automatically increased.
7.10
Writing to multiple registers with incremental addressing
It would be unpractical to send several times the device address and the address of the
register when writing to multiple registers. STCF03I supports writing to multiple registers
with incremental addressing. When data is written to a register, the address register is
automatically increased, so the next data can be sent without sending the device address
and the register address again. See Figure 9 below.
Figure 9.
Writing to multiple registers with incremental addressing
DEVICE
ADDRESS
7 bits
S M
T S
A B
R
T
W
R
I
T
E
L R A M
S / C S
B W K B
ADDRESS OF
REGISTER i
DATA i
L A M
S C S
B K B
DATA i+1
L A M
S C S
B K B
DATA i+2
L A M
S C S
B K B
DATA i+2
L A M
S C S
B K B
DATA i+n
L A M
S C S
B K B
L A S
S C T
B K O
P
SDA LINE
7.11
Reading from a single register
The reading operation starts with a START bit followed by the 7 bit device address of
STCF03I. The 8th bit is the R/W bit, which is 0 in this case. STCF03I confirms the receiving
of the address + R/W bit by an acknowledge pulse. The address of the register which should
be read is sent afterwards and confirmed again by an acknowledge pulse of STCF03I again.
Then the master generates a START bit again and sends the device address followed by the
R/W bit, which is 1 now. STCF03I confirms the receiving of the address + R/W bit by an
acknowledge pulse and starts to send the data to the master. No acknowledge pulse from
the master is required after receiving the data. Then the master generates a STOP bit to
terminate the communication. See Figure 10
18/33
Introduction
STCF03I
Figure 10. Reading from a single register
DEVICE
ADDRESS
7 bits
S M
T S
A B
R
T
W
R
I
T
E
ADDRESS
OF
REGISTER
DEVICE
ADDRESS
7 bits
L R A M
S / C S
B WK B
L A S
S C T
B K A
R
T
R
E
A
D
DATA
R A
/ C
WK
L N S
S O T
O
B
A P
C
K
SDA LINE
7.12
Reading from multiple registers with incremental addressing
Reading from multiple registers starts in the same way like reading from a single register. As
soon as the first register is read, the register address is automatically increased. If the
master generates an acknowledge pulse after receiving the data from the first register, then
reading of the next register can start immediately without sending the device address and
the register address again. The last acknowledge pulse before the STOP bit is not required.
See the Figure 11.
Figure 11. Reading from multiple registers
DEVICE
ADDRESS
7 bits
S M
T S
A B
R
T
W
R
I
T
E
L R A M
S / C S
B W K B
DEVICE
ADDRESS
7 bits
ADDRESS OF
REGISTER i
L A S
S C T
B K A
R
T
R
E
A
D
R A
/ C
W K
DATA i
DATA i+1
L A M
S C S
B K B
SDA LINE
19/33
DATA i+2
L A M
S C S
B K B
DATA i+2
L A M
S C S
B K B
DATA i+n
L A M
S C S
B K B
L N S
S O T
B
O
A P
C
K
Description of internal registers
8
STCF03I
Description of internal registers
Table 9. I2C Register mapping function
Register name
SUB ADDRESS (hex)
Operation
CMD_REG
00
R/W
DIM_REG
01
R/W
AUX_REG
02
R/W
STAT_REG
03
R only
Table 10. Command register
CMD_REG
(write mode)
MSB
SUB ADD=00
PWR_ON
TRIG_EN
TCH_ON
NTC_ON
FTIM_3
FTIM_2
FTIM_1
FTIM_0
Power ON
RESET Value
0
0
0
0
0
0
0
0
8.1
LSB
PWR_ON
When set, it activates all analog and power internal blocks including the NTC supporting
circuit, and the device is ready to operate (Ready Mode). As long as PWR_ON=0, only the
I2C interface is active, minimizing Stand-by Mode power consumption.
8.2
TRIG_EN
This bit is AND-ed with the TRIG pin to generate the internal signal FL_ON that activates
Flash Mode. By this way, both soft-triggering and hard-triggering of the Flash are made
possible. If soft-triggering (through I2C) is chosen, the TRIG pin is not used and must be
kept HIGH (VI). If hard-triggering is chosen, then the TRIG pin has to be connected to a µP
I/O devoted to Flash timing control, and the TRIG_EN bit must be set in advance. Both
triggering modes can benefit of the internal Flash Time Counter, that uses the TRIG_EN bit
and can work either as a safety shut-down timer or as a Flash duration timer. Flash mode
can start only if PWR_ON=1. LED current is controlled by the value set by the FDIM_0~3 of
the DIM_REG.
8.3
TCH_ON
When set from Ready Mode, the STCF03I enters Torch mode. The LED current is controlled
by the value set by the TDIM_0~3 of the DIM_REG.
8.4
NTC_ON
When the NTC_ON bit is set to HIGH and the device is in Ready mode, then the
comparators that monitor the LED temperature are activated. NTC-related blocks are always
active regardless of this bit in Torch mode and Flash mode.
20/33
Description of internal registers
8.5
STCF03I
FTIM_0~3
This 4-bits register defines the maximum Flash duration. It is intended to limit the energy
dissipated by the LED to a maximum safe value or to leave to the STCF03I the control of the
Flash duration during normal operation. Values from 0~15 correspond to 0~1.5 s (100 ms
steps). The timing accuracy is related to the internal oscillator frequency that clocks the
Flash Time Counter (+/-20%, TBD). Entering Flash mode (either by soft or hard triggering)
activates the Flash Time Counter, which begins counting down from the value loaded in the
F_TIM register. When the counter reaches zero, Flash mode is stopped by resetting
TRIG_EN bit, and simultaneously the ATN pin is set to true (LOW) to alert the µP that the
maximum time has been reached. FTIM value remains unaltered at the end of the count.
Table 11. Dimming register
DIM_REG
(write mode)
MSB
SUB ADD=01
TDIM_3
TDIM_2
TDIM_1
TDIM_0
FDIM_3
FDIM_2
FDIM_1
FDIM_0
Power ON,
SHUTDOWN MODE
RESET Value
0
0
0
0
0
0
0
0
8.6
LSB
TDIM_0~3
These 4 bits define the LED current in Torch mode with 16 values fitting an exponential law.
Max Torch current value is 25% of max Flash current. (Figure 12)
8.7
FDIM_0~3
These 4 bits define the LED current in Flash mode with 16 values fitting an exponential law.
The Max value of the current is set by the external resistors RFL and RTR. (Figure 12)
Figure 12. Flash and Torch current vs. dimming value
Current Step Coefficient - 1.19
Note:
21/33
LED current values refer to RFL=0.27 Ω, RTR=1.8 Ω
Description of internal registers
STCF03I
Table 12. Auxiliary register
AUX_REG
(write mode)
MSB
SUB ADD=02
AUXI_3
AUXI_2
AUXI_1
AUXI_0
AUXT_3
AUXT_2
AUXT_1
AUXT_0
Power ON,
SHUTDOWN MODE
RESET Value
0
0
0
0
0
0
0
0
8.8
LSB
AUXI_0~3
This 4 bits register defines the AUX LED current from 0 to 20 mA. See AUX LED Dimming
Table for reference. Loading any value between 1 and 15 also starts the AUX LED current
source timer, if enabled. The AUX LED current source is active only in Ready Mode, and is
deactivated in any other mode.
8.9
AUXT_0~3
This 4 bit register controls the timer that defines the ON-time of the AUX LED current
source. ON-time starts when the AUXI register is loaded with any value other than zero, and
stops after the time defined in the AUXT register. Values from 1 to 14 of the AUXT register
correspond to an ON-time of the AUX LED ranging from 100 to 1400 ms in 100 ms steps.
The value 15 puts the AUX LED to the continuous light mode. The activation/deactivation of
the AUX LED current source is controlled using only the AUXI register.
Table 13. Auxiliary led dimming table (1)
AUXI (hex)
0
1
2
3
4
5
6
7
AUX LED
current [mA]
0.0
1.3
2.6
4.0
5.3
6.6
8.0
9.3
8
9
A
B
C
D
E
F
10.6 12.0 13.3 14.6 16.0 17.3 18.6 20.0
1. 20 mA output current is achievable only if the supply voltage is higher than 3.3 V.
Table 14. Torch Mode and Flash Mode dimming registers settings
T_DIM
(hex)
0
1
2
3
4
5
6
7
F_DIM
(hex)
8
9
A
B
C
D
E
F
0
1
2
3
4
5
6
7
8
9
A
B
C
D
E
F
LED
current
[mA]
16
19
23
27
32
39
46
55
65
77
92
109 124 147 175 209 248 296 352 418 498 592 705 840
Internal
step
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
VREF1
[mV]
33
40
47
56
67
80
95
113 134 160 190
227
33
40
47
56
67
79
95
113 134 160 190 227
Sense
Resist.
Note:
22/33
21
22
23
24
RFL RFL RFL RFL RFL RFL RFL RFL RFL RFL RFL RFL RFL RFL RFL RFL RFL RFL RFL RFL RFL RFL RFL RFL
+
+
+
+
+
+
+
+
+
+
+
+
RTR RTR RTR RTR RTR RTR RTR RTR RTR RTR RTR RTR
LED current values refer to RFL=0.27 Ω, RTR=1.8 Ω.
Description of internal registers
STCF03I
Table 15. Status register
STAT_REG
(read mode)
MSB
SUB ADD=03
N/A
F_RUN
LED_F
NTC_W
NTC_H
OT_F
N/A
VOUTOK_N
Power ON,
SHUTDOWN MODE
RESET Value
0
0
0
0
0
0
0
0
8.10
LSB
F_RUN
This bit is kept HIGH by the STCF03I during Flash mode. By checking this bit, the µP can
verify if the Flash mode is running or has been terminated by the Time Counter.
8.11
LED_F
This bit is set by the STCF03I when the voltage seen on the LED pin is VREF2 > 5.3 V during
a Torch or Flash operation. This condition can be caused by an open LED, indicating a LED
failure. The device automatically goes into Ready mode to avoid damage. Internal high
frequency filtering avoids false detections. This bit is reset by the STCF03I following a read
operation of the STAT_REG.
8.12
NTC_W
This bit is set HIGH by the STCF03I and the ATN pin is pulled down, when the voltage seen
on the pin Rx exceeds VREF4 = 0.56 V. This threshold corresponds to a warning temperature
value at the LED measured by the NTC. The device is still operating, but a warning is sent to
the µP. This bit is reset by the STCF03I following a read operation of the STAT_REG.
8.13
NTC_H
This bit is set HIGH by the STCF03I and the ATN pin is pulled down, when the voltage seen
on the pin Rx exceeds VREF5. This threshold (1.2 V) corresponds to an excess temperature
value at the LED measured by the NTC. The device is put in Ready mode to avoid damaging
the LED. This bit is reset by the STCF03I following a read operation of the STAT_REG.
8.14
OT_F
This bit is set HIGH by the STCF03I and the ATN pin is pulled down, when the chip overtemperature protection (~140°C) has put the device in Ready mode. This bit is reset by the
STCF03I following a read operation of the STAT_REG.
23/33
Description of internal registers
8.15
STCF03I
VOUTOK_N
This bit is set by the STCF03I. It is used to protect the device, if the output is shorted. The
VOUTOK_N bit is set to HIGH at the start-up. Then a current generator of 20 mA charges
the output capacitor for 360 µs typ. and it detects when the output capacitor reaches 100
mV. If this threshold is reached the bit is set to LOW. If the output is shorted to ground or the
LED is shorted, this threshold is never reached: the bit stays HIGH, ATN pin is pulled down
and the device will not start. This bit is reset following a read operation of the STAT_REG
Figure 13. VOUTOK_N behavior
Table 16. Status register details
Bit Name
F_RUN
(STAT_REG)
LED_F
(STAT_REG)
NTC_W
(STAT_REG)
NTC_H
(STAT_REG)
OT_F
(STAT_REG)
VOUTOK_N
(STAT_REG)
Default value
0
0
0
0
0
0
NO
YES
YES
YES
YES
YES
Forces
Ready mode
when set
NO
YES
NO
YES
YES
YES
Sets ATN
LOW when
set
NO
YES
YES
YES
YES
YES
Latched
(1)
1. YES means that the bit is set by internal signals and is reset to default by an I2C read operation of STAT_REG NO means
that the bit is set and reset by internal signals in real-time.
24/33
Detailed description
9
Detailed description
9.1
PowerON reset
STCF03I
This mode is initiated by applying a supply voltage above the VPW_ON RESET threshold
value. An internal timing (~1 µs) defines the duration of this status. The logic blocks are
powered, but the device doesn't respond to any input. The registers are reset to their default
values, the ATN and SDA pins are in high-Z, and the I2C slave address is internally set by
reading the ADD pin configuration. After the internally defined time has elapsed, the
STCF03I automatically enters the Stand-by mode.
9.2
Shutdown
In this mode, only the I2C interface is alive, accepting I2C commands and register settings.
The device enters this mode: automatically from Power ON Reset status; by resetting the
PWR_ON bit from other operation modes. Power consumption is at the minimum (1 µA typ).
9.3
Ready mode
In this mode all internal blocks are turned ON, but the DC/DC converter is disabled and the
White LED is disconnected. The NTC circuit can be activated to monitor the temperature of
the LED and I2C commands and register settings are allowed to be executed immediately.
Only in this mode the Auxiliary LED is operational and can be turned ON and set at the
desired brightness using the AUX REGISTER. The device enters this mode: from Stand-by
by setting the PWR_ON bit; from Flash operation by resetting the TRIG pin or the TRIG_EN
bit or automatically from Flash operation when the Time Counter reaches zero; from Torch
operation by resetting the TCH_ON bit. The device automatically enters this mode also
when an overload or an abnormal condition has been detected during Flash or Torch
operation (Table 16: Status register details:).
9.4
Single or multiple Flash using external (µP) temporization
To avoid the I2C bus time latency, it is recommended to use the dedicated TRIG pin to define
the Flash duration (hard-triggering). The TRIG_EN bit of CMD_REG should be set before
starting each flash operation, because it could have been reset automatically in the previous
Flash operation. The Flash duration is determined by the pulse length that drives the TRIG
pin. As soon as the Flash is activated, the system needs typically 1.2 ms to ramp up the
output current on the Power LED. The internal Time Counter will Time-out Flash operation
and keep the LED dissipated energy within safe limits in case of Software deadlock; FTIM
register has to be set first, either in Stand-by or in Ready Mode. Multiple flashes are possible
by strobing the TRIG pin. Time out counter will cumulate every flash on-time until the
defined time out is reached unless it is reloaded by updating the CMD_REG. After a single
or multiple Flash operations are timed-out, the device automatically goes into Ready mode
by resetting the TRIG_EN bit, and also resets the F_RUN bit. The ATN pin is pulled down to
inform the µP that the STAT_REG has been updated.
25/33
Detailed description
9.5
STCF03I
External (µP) temporization using TRIG_EN bit
Even if it is possible, it is not recommended to use the TRIG_EN bit to start and stop the
Flash operation, because of I2C bus latencies: this would result in inaccurate Flash timing.
Nevertheless, if this operation mode is chosen, the TRIG pin has to be kept High (logic level
or wired to VBAT), leaving the whole flash control to the I2C bus. Also in this operation mode
the Time Counter will Time-out Flash operation and keep the energy dissipated by the LED
within safe limits in case of SW deadlock.
9.6
Single Flash using internal temporization
Flash triggering can be obtained either by TRIG pin (hard-triggering) or by I2C commands
(soft-triggering). The first solution is recommended for an accurate start time, while the
second is less accurate because of the I2C bus time latency. Stop time is defined by the
STCF03I internal temporization and its accuracy is determined by the internal oscillator. For
hard-triggering, it is necessary to set the TRIG_EN bit in advance. For soft-triggering, the
TRIG pin has to be kept High (logic level or wired to VBAT) and the Flash can be started by
setting the FTIM and the TRIG_EN through I2C (both are located in the CMD REG). There is
a delay time between the moment the Flash is triggered and when it appears. This delay is
caused by the time necessary to charge up the output capacitor, which is around 1.2 ms
depending on battery voltage and output current value. Once triggered, the flash operation
will be stopped when the Time Counter reaches zero. As soon as the Flash is finished, the
F_RUN bit is reset, the ATN pin is pulled down for 11 µs to inform the µP that the STAT_REG
has been updated and the device goes back to Ready mode. If it is necessary to make a
Flash longer than the internal timer allows or a continuous Flash, then the FTIM must be
reloaded through I2C bus every time, before the internal timer reaches zero. For example: To
get a continuous FLASH, set FTIM to 1.5 s and every 1 s reload the CMD_REG.
9.7
Multiple Flash using internal temporization
This operation has to be processed as a sequence of single flashes using internal
temporization starting from hard or soft triggering. Since the TRIG_EN bit is reset at the end
of each flash, it is necessary to reload the CMD_REG to start the next one.
26/33
Typical performance characteristics
STCF03I
Typical performance characteristics
10
Figure 14. Flash current vs F_DIMM
Figure 15. Torch current vs T_DIMM
250
900
800
200
700
600
mA
mA
150
500
400
100
300
200
50
100
0
0
0
1
2
3
4
5
6
7
8
9 10 11 12 13 14 15
0
1
2
3
4
5
step
6
7
8
9 10 11 12 13 14 15
step
Figure 16. Aux current vs AUXI
Figure 17.
25
Flash current vs temp
850
845
20
840
835
830
mA
mA
15
825
820
10
815
Flash current= 800mA
V BAT=3.3V
810
5
805
800
0
0
1
2
3
4
5
6
7
8
-40°C
9 10 11 12 13 14 15
25°C
80°C
temp.
Step
Figure 18. VFB2 Flash vs temp
Figure 19. IQ vs temp
250
2.4
2.3
245
2.2
2.1
mA
mV
240
235
2
1.9
230
1.8
225
1.7
1.6
220
-40°C
25°C
temp.
27/33
80°C
-40°C
25°C
temp.
85°C
Typical performance characteristics
STCF03I
Figure 20. Efficiency
Figure 21. Start-Up in Flash Mode 800 mA at
VI = 3.6 V
95
90
TRIG
Flash 800mA
85
Io
Torch 55mA
Eff %
80
75
70
65
I_IN
60
55
50
2.5
3
3.5
4
4.5
5
5.5
VI [V]
Figure 22. Line transient in Flash Mode 800
mA, change of VI from 2.7 V to 3.3V
in 10 µs
Io
VI
I_IN
28/33
Package mechanical data
11
STCF03I
Package mechanical data
In order to meet environmental requirements, ST offers these devices in ECOPACK®
packages. These packages have a Lead-free second level interconnect. The category of
second level interconnect is marked on the package and on the inner box label, in
compliance with JEDEC Standard JESD97. The maximum ratings related to soldering
conditions are also marked on the inner box label. ECOPACK is an ST trademark.
ECOPACK specifications are available at: www.st.com
29/33
Package mechanical data
STCF03I
TFBGA25 mechanical data
mm.
mils.
Dim.
A
Min.
Typ.
Max.
Min.
Typ.
Max.
1.0
1.1
1.16
39.4
43.3
45.7
A1
0.25
A2
0.78
b
0.25
D
2.9
D1
E
9.8
0.86
30.7
0.30
0.35
9.8
11.8
13.8
3.0
3.1
114.2
118.1
122.0
2
2.9
3.0
33.9
78.8
3.1
114.2
118.1
E1
2
78.8
e
0.5
19.7
SE
0.25
9.8
122.0
7539979/A
30/33
Package mechanical data
STCF03I
Tape & reel TFBGA25 mechanical data
mm.
inch.
Dim.
Min.
Typ.
A
Min.
Typ.
330
13.2
Max.
12.992
C
12.8
D
20.2
0.795
N
60
2.362
T
31/33
Max.
0.504
0.519
14.4
0.567
Ao
3.3
0.130
Bo
3.3
0.130
Ko
1.60
0.063
Po
3.9
4.1
0.153
0.161
P
7.9
8.1
0.311
0.319
Revision history
12
STCF03I
Revision history
Table 17. Document revision history
Date
Revision
23-Jul-2007
1
First release.
27-Aug-2007
2
Table 5. updated.
05-Sep-2007
3
Add row NTC_REF on Table 6.
12-Sep-2007
4
Figure 2. title changed.
32/33
Changes
STCF03I
Please Read Carefully:
Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the
right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any
time, without notice.
All ST products are sold pursuant to ST’s terms and conditions of sale.
Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no
liability whatsoever relating to the choice, selection or use of the ST products and services described herein.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this
document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products
or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such
third party products or services or any intellectual property contained therein.
UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED
WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS
OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.
UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT
RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING
APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY,
DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE
GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK.
Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void
any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any
liability of ST.
ST and the ST logo are trademarks or registered trademarks of ST in various countries.
Information in this document supersedes and replaces all information previously supplied.
The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.
© 2007 STMicroelectronics - All rights reserved
STMicroelectronics group of companies
Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America
www.st.com
33/33