STGBL6NC60D - STGDL6NC60D STGFL6NC60D - STGPL6NC60D N-channel 600V - 6A - DPAK / D2PAK / TO-220 / TO-220FP Hyper fast IGBT Features Type VCES IC @100°C STGBL6NC60D STGDL6NC60D STGPL6NC60D STGFL6NC60D 600V 600V 600V 600V 8A 7A 8A 4A ■ Very high frequency operation ■ Low CRES / CIES ratio (no cross-conduction susceptibility) ■ Very soft ultra fast recovery antiparallel diode 3 1 3 2 1 TO-220FP TO-220 3 3 1 1 DPAK 2 D²PAK Description Based on PowerMESH technology and thanks to a new lifetime control system, this new series exhibits very low turn-off energy realizing the best trade-off between on-state voltage and switching losses and so allowing very high operating frequencies. Figure 1. Internal schematic diagram Applications ■ Very high frequency applications ■ High frequency lamp ballast ■ SMPS and PFC (hard switching too) Table 1. Device summary Order codes Marking Package Packaging STGBL6NC60DT4 GBL6NC60D D²PAK Tape & reel STGDL6NC60DT4 GDL6NC60D DPAK Tape & reel STGPL6NC60D GPL6NC60D TO-220 Tube STGFL6NC60D GFL6NC60D TO-220FP Tube July 2007 Rev 1 1/19 www.st.com 19 Contents STGBL6NC60D - STGDL6NC60D - STGPL6NC60D - STGFL6NC60D Contents 1 Electrical ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 2.1 Electrical characteristics (curves) ............................. 7 3 Test circuit 4 Package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 5 Packaging mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 6 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 2/19 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 STGBL6NC60D - STGDL6NC60D - STGPL6NC60D - STGFL6NC60D 1 Electrical ratings Electrical ratings Table 2. Absolute maximum ratings Value Symbol Parameter DPAK TO-220 D²PAK Unit TO-220FP VCES Collector-emitter voltage (VGS = 0) IC(1) Collector current (continuous) at TC = 25°C 13 14 7 A IC(1) Collector current (continuous) at TC = 100°C 7 8 4 A ICP(2) Pulsed collector current 25 A VGE Gate-emitter voltage ±20 V Diode RMS forward current at Tc=25°C 7 A IFSM Surge non repetitive forward current tp=10ms sinusoidal 20 A PTOT Total dissipation at TC = 25°C 50 56 22 W VISO Insulation withstand voltage (RMS) from all three leads to external heat sink (t=1s;TC=25°C) -- -- 2500 V IF Tj 600 Operating junction temperature V – 55 to 150 °C 1. Calculated according to the iterative formula: T –T JMAX C I ( T ) = ----------------------------------------------------------------------------------------------------C C R × V (T , I ) THJ – C CESAT ( MAX ) C C 2. Pulsed: width limited by max junction temperature allowed Table 3. Thermal resistance Value Symbol Parameter TO-220 D²PAK Unit DPAK TO-220FP Rthj-case Thermal resistance junction-case max (IGBT) 2.2 2.5 5.6 °C/W Rthj-case Thermal resistance junction-case max (diode) 4 4.5 7 °C/W Rthj-amb Thermal resistance junction-ambient max 62.5 °C/W 3/19 Electrical characteristics 2 STGBL6NC60D - STGDL6NC60D - STGPL6NC60D - STGFL6NC60D Electrical characteristics (TCASE=25°C unless otherwise specified) Table 4. Symbol Parameter VBR(CES) Collector-emitter breakdown voltage VCE(sat) VGE = 15V, IC= 3A Collector-emitter saturation VGE= 15V, IC= 3A,@ 125°C voltage VGE = 15V, IC= 1.5A VGE(th) Gate threshold voltage VCE= VGE, IC= 250 µA ICES Collector cut-off current (VGE = 0) VCE = Max rating,TC= 25°C IGES Gate-emitter leakage current (VCE = 0) VGE = ±20V, VCE= 0 Forward transconductance VCE = 15V, IC= 3A gfs Table 5. Symbol Cies Coes Cres Qg Qge Qgc 4/19 Static electrical characteristics Test conditions IC = 1mA, VGE = 0 Min. Typ. Max. 600 Unit V 2.3 2.1 2.0 3.75 VCE = Max rating,TC= 125°C 2.9 V V V 5.75 V 50 5 µA mA ±100 nA 3 S Dynamic electrical characteristics Parameter Input capacitance Output capacitance Reverse transfer capacitance Total gate charge Gate-emitter charge Gate-collector charge Test conditions VCE = 25V, f = 1MHz, VGE = 0 VCE = 390V, IC = 3A, VGE = 15V, (see Figure 17) Min. Typ. Max. Unit 208 32.5 5.4 pF pF pF 12 2.6 4.9 nC nC nC STGBL6NC60D - STGDL6NC60D - STGPL6NC60D - STGFL6NC60D Table 6. Symbol td(on) tr (di/dt)on td(on) tr (di/dt)on tr(Voff) td(off) tf tr(Voff) td(off) tf Table 7. Symbol Eon (1) Eoff(2) Ets Eon (1) Eoff(2) Ets 1. Electrical characteristics Switching on/off (inductive load) Parameter Test conditions Turn-on delay time Current rise time Turn-on current slope VCC = 390V, IC = 3A Turn-on delay time Current rise time Turn-on current slope VCC = 390V, IC = 3A Off voltage rise time Turn-off delay time Current fall time VCC = 390V, IC = 3A, Off voltage rise time Turn-off delay time Current fall time VCC = 390V, IC = 3A, Min. RG= 10Ω, VGE = 15V, Tj = 25°C (see Figure 18) RG = 10Ω, VGE = 15V, Tj =125°C (see Figure 18) RGE = 10Ω, VGE = 15V, TJ = 25°C (see Figure 18) RGE = 10Ω, VGE =15V, Tj = 125°C (see Figure 18) Typ. Max. Unit 6.7 3.7 930 ns ns A/µs 6.5 4 820 ns ns A/µs 17 46 47 ns ns ns 35 67 55 ns ns ns Switching energy (inductive load) Parameter Test conditions Turn-on switching losses Turn-off switching losses Total switching losses VCC = 390V, IC = 3A Turn-on switching losses Turn-off switching losses Total switching losses VCC = 390V, IC = 3A RG = 10Ω, VGE=15V, Tj =25°C (see Figure 18) RG = 10Ω, VGE = 15V, Tj = 125°C (see Figure 18) Min. Typ. Max. Unit 46.5 23.5 70 µJ µJ µJ 67.5 46 113.5 µJ µJ µJ Eon is the turn-on losses when a typical diode is used in the test circuit in (see Figure 19). If the IGBT is offered in a package with a co-pak diode, the co-pack diode is used as external diode. IGBTs & Diode are at the same temperature (25°C and 125°C) 2. Turn-off losses include also the tail of the collector current 5/19 Electrical characteristics Table 8. Symbol STGBL6NC60D - STGDL6NC60D - STGPL6NC60D - STGFL6NC60D Turn-off with snubber Parameter Test conditions Min. Typ. Max. Unit VCC = 200V, IC = 1.5A tf Eoff(1) Current fall time Turn-off switching losses RG = 22Ω, Vclamp=400V, L=1mH, C-snubber=2.7nF Tj =25°C (see Figure 18) 16 5.5 ns µJ 19 6 ns µJ VCC = 200V, IC = 1.5A tf Eoff (1) Current fall time Turn-off switching losses RG = 22Ω, Vclamp=400V, L=1mH, C-snubber=2.7nF, Tj = 125°C (see Figure 18) 1. Turn-off losses include also the tail of the collector current Table 9. Symbol Collector-emitter diode Parameter Test conditions Min. Typ. Max. Unit 1.7 1.7 1.5 V V V 30 33.5 2.2 ns nC A 65 94 2.9 ns nC A If = 1A Vf Forward on-voltage If=3A If=3A,Tj=125°C trr Qrr Irrm trr Qrr Irrm 6/19 If = 3A,VR = 40V, Reverse recovery time Reverse recovery charge Reverse recovery current Tj = 25°C, di/dt = 100 A/µs (see Figure 19) Reverse recovery time Reverse recovery charge Reverse recovery current Tj =125°C, di/dt = 100A/µs (see Figure 19) If = 3A,VR = 40V, STGBL6NC60D - STGDL6NC60D - STGPL6NC60D - STGFL6NC60D Electrical characteristics 2.1 Electrical characteristics (curves) Figure 2. Output characteristics Figure 3. Transfer characteristics Figure 4. Transconductance Figure 5. Collector-emitter on voltage vs temperature Figure 6. Gate charge vs gate-source voltage Figure 7. Capacitance variations 7/19 Electrical characteristics Figure 8. STGBL6NC60D - STGDL6NC60D - STGPL6NC60D - STGFL6NC60D Normalized gate threshold voltage vs temperature Figure 10. Normalized breakdown voltage vs temperature Figure 9. Collector-emitter on voltage vs collector current Figure 11. Switching losses vs temperature Figure 12. Switching losses vs gate resistance Figure 13. Switching losses vs collector current 8/19 STGBL6NC60D - STGDL6NC60D - STGPL6NC60D - STGFL6NC60D Figure 14. Turn-off SOA Electrical characteristics Figure 15. Forward voltage drop versus forward current 9/19 Test circuit 3 STGBL6NC60D - STGDL6NC60D - STGPL6NC60D - STGFL6NC60D Test circuit Figure 16. Test circuit for inductive load switching Figure 17. Gate charge test circuit Figure 18. Switching waveform Figure 19. Diode recovery time waveform 10/19 STGBL6NC60D - STGDL6NC60D - STGPL6NC60D - STGFL6NC60D 4 Package mechanical data Package mechanical data In order to meet environmental requirements, ST offers these devices in ECOPACK® packages. These packages have a Lead-free second level interconnect. The category of second level interconnect is marked on the package and on the inner box label, in compliance with JEDEC Standard JESD97. The maximum ratings related to soldering conditions are also marked on the inner box label. ECOPACK is an ST trademark. ECOPACK specifications are available at: www.st.com 11/19 Package mechanical data STGBL6NC60D - STGDL6NC60D - STGPL6NC60D - STGFL6NC60D TO-220 mechanical data mm inch Dim Min A b b1 c D D1 E e e1 F H1 J1 L L1 L20 L30 ∅P Q 12/19 Typ 4.40 0.61 1.14 0.49 15.25 Max Min 4.60 0.88 1.70 0.70 15.75 0.173 0.024 0.044 0.019 0.6 10.40 2.70 5.15 1.32 6.60 2.72 14 3.93 0.393 0.094 0.194 0.048 0.244 0.094 0.511 0.137 1.27 10 2.40 4.95 1.23 6.20 2.40 13 3.50 Max 0.181 0.034 0.066 0.027 0.62 0.050 16.40 28.90 3.75 2.65 Typ 0.409 0.106 0.202 0.051 0.256 0.107 0.551 0.154 0.645 1.137 3.85 2.95 0.147 0.104 0.151 0.116 STGBL6NC60D - STGDL6NC60D - STGPL6NC60D - STGFL6NC60D Package mechanical data TO-220FP MECHANICAL DATA mm. DIM. MIN. A 4.4 inch TYP MAX. MIN. TYP. 4.6 0.173 0.181 MAX. 0.106 B 2.5 2.7 0.098 D 2.5 2.75 0.098 0.108 E 0.45 0.7 0.017 0.027 F 0.75 1 0.030 0.039 F1 1.15 1.7 0.045 0.067 F2 1.15 1.7 0.045 0.067 G 4.95 5.2 0.195 0.204 G1 2.4 2.7 0.094 0.106 H 10 10.4 0.393 0.409 L2 16 0.630 L3 28.6 30.6 1.126 1.204 L4 9.8 10.6 .0385 0.417 L5 2.9 3.6 0.114 0.141 L6 15.9 16.4 0.626 0.645 9 9.3 0.354 0.366 Ø 3 3.2 0.118 0.126 B D A E L7 L3 L6 F2 H G G1 F F1 L7 L2 L5 1 2 3 L4 13/19 Package mechanical data STGBL6NC60D - STGDL6NC60D - STGPL6NC60D - STGFL6NC60D DPAK MECHANICAL DATA mm. inch DIM. MIN. A A1 A2 B b4 C C2 D D1 E E1 e e1 H L (L1) L2 L4 R V2 TYP 2.2 0.9 0.03 0.64 5.2 0.45 0.48 6 MAX. MIN. 2.4 1.1 0.23 0.9 5.4 0.6 0.6 6.2 0.086 0.035 0.001 0.025 0.204 0.017 0.019 0.236 6.6 0.252 5.1 6.4 0.260 0.090 4.6 10.1 0.173 0.368 0.039 2.8 0.8 0.181 0.397 0.110 0.031 1 0.023 0.2 0° 0.094 0.043 0.009 0.035 0.212 0.023 0.023 0.244 0.185 2.28 0.6 MAX. 0.200 4.7 4.4 9.35 1 TYP. 0.039 0.008 8° 0° 8° 0068772-F 14/19 STGBL6NC60D - STGDL6NC60D - STGPL6NC60D - STGFL6NC60D Package mechanical data D2PAK MECHANICAL DATA TO-247 MECHANICAL DATA mm. inch DIM. MIN. TYP MAX. MIN. TYP. MAX. A 4.4 4.6 0.173 0.181 A1 2.49 2.69 0.098 0.106 A2 0.03 0.23 0.001 0.009 B 0.7 0.93 0.027 0.036 B2 1.14 1.7 0.044 0.067 C 0.45 0.6 0.017 0.023 C2 1.23 1.36 0.048 0.053 D 8.95 9.35 0.352 0.368 D1 E 8 10 E1 G 0.315 10.4 0.393 8.5 0.334 4.88 5.28 0.192 0.208 L 15 15.85 0.590 0.625 L2 1.27 1.4 0.050 0.055 L3 1.4 1.75 0.055 0.068 M 2.4 3.2 0.094 R 0º 0.126 0.015 4º 3 V2 0.4 1 15/19 Packaging mechanical data 5 STGBL6NC60D - STGDL6NC60D - STGPL6NC60D - STGFL6NC60D Packaging mechanical data DPAK FOOTPRINT All dimensions are in millimeters TAPE AND REEL SHIPMENT REEL MECHANICAL DATA DIM. mm MIN. A B 1.5 C 12.8 D 20.2 G 16.4 N 50 T TAPE MECHANICAL DATA DIM. mm MIN. MAX. A0 6.8 7 0.267 0.275 B0 10.4 10.6 0.409 0.417 B1 D 16/19 inch 1.5 D1 1.5 E 1.65 MIN. MAX. 12.1 0.476 1.6 0.059 0.063 1.85 0.065 0.073 0.059 F 7.4 7.6 0.291 0.299 K0 2.55 2.75 0.100 0.108 0.153 0.161 P0 3.9 4.1 P1 7.9 8.1 0.311 0.319 P2 1.9 2.1 0.075 0.082 R 40 W 15.7 1.574 16.3 0.618 0.641 inch MAX. MIN. MAX. 330 12.992 13.2 0.504 0.520 18.4 0.645 0.724 0.059 0.795 1.968 22.4 0.881 BASE QTY BULK QTY 2500 2500 STGBL6NC60D - STGDL6NC60D - STGPL6NC60D - STGFL6NC60D Packaging mechanical data D2PAK FOOTPRINT TAPE AND REEL SHIPMENT REEL MECHANICAL DATA DIM. mm MIN. A B 1.5 C 12.8 D 20.2 G 24.4 N 100 T TAPE MECHANICAL DATA DIM. mm inch MIN. MAX. MIN. A0 10.5 10.7 0.413 0.421 B0 15.7 15.9 0.618 0.626 D 1.5 1.6 0.059 0.063 D1 1.59 1.61 0.062 0.063 E 1.65 1.85 0.065 0.073 F 11.4 11.6 0.449 0.456 inch MAX. MIN. MAX. 330 12.992 13.2 0.504 0.520 26.4 0.960 1.039 0.059 0795 3.937 30.4 1.197 BASE QTY BULK QTY 1000 1000 MAX. K0 4.8 5.0 0.189 0.197 P0 3.9 4.1 0.153 0.161 P1 11.9 12.1 0.468 0.476 P2 1.9 2.1 0.075 0.082 R 50 1.574 T 0.25 0.35 0.0098 0.0137 W 23.7 24.3 0.933 0.956 * on sales type 17/19 Revision history 6 STGBL6NC60D - STGDL6NC60D - STGPL6NC60D - STGFL6NC60D Revision history Table 10. 18/19 Revision history Date Revision 18-Jul-2007 1 Changes First Release STGBL6NC60D - STGDL6NC60D - STGPL6NC60D - STGFL6NC60D Please Read Carefully: Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST’s terms and conditions of sale. Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein. UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY, DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK. Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST. ST and the ST logo are trademarks or registered trademarks of ST in various countries. Information in this document supersedes and replaces all information previously supplied. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners. © 2007 STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com 19/19