STMICROELECTRONICS STM1403ATNQ6F

STM1403
3 V FIPS-140
security supervisor with battery switchover
Features
■
STM1403 supports FIPS-140 security level 3+
– Four high-impedance physical tamper
inputs
– Over/under operating voltage detector
– Security alarm (SAL) on tamper detection
■
Supervisory functions
– Automatic battery switchover
– RST output (open drain)
– Manual (push-button) reset input (MR)
– Power-fail comparator (PFI/PFO)
■
Vccsw (VCC switch output)
– Low when switched to VCC
– High when switched to VBAT (BATT ON
indicator)
■
Battery low voltage detector (power-up)
■
Optional VREF (1.237 V)
– (Available for STM1403A only)
■
Low battery supply current (2.8 µA, typ)
■
Secure low profile 16-pin, 3 x 3 mm, QFN
package
Table 1.
QFN16, 3 mm x 3 mm (Q)
Device summary
Standard
supervisory
functions(1)
Physical
tamper
inputs
Over/under
voltage
alarms
VREF
(1.237 V)
option
VOUT status,
during alarm
Vccsw status,
during alarm
STM1403A
✔
✔
✔
✔
ON
Normal mode(2)
STM1403B(3)
✔
✔
✔
Note(4)
High-Z
High
STM1403C
✔
✔
✔
Note(4)
Ground
High
Device
1. Reset output, power-fail comparator, battery low detection (SAL, RST, PFO, and BLD are open drain).
2. Normal mode: low when VOUT is internally switched to VCC and high when VOUT is internally switched to battery.
3. Contact local ST sales office for availability.
4. Pin 9 is the VREF pin for STM1403A. It is the VTPU pin for STM1403B/C.
August 2008
Rev 5
1/35
www.st.com
1
Contents
STM1403
Contents
1
Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
1.1
2
VOUT pin modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
1.1.1
STM1403A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
1.1.2
STM1403B . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
1.1.3
STM1403C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Pin descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
2.1
SAL, security alarm output (open drain) . . . . . . . . . . . . . . . . . . . . . . . . . . 11
2.1.1
TP1, TP3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
2.1.2
TP2, TP4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
2.1.3
Vccsw, VCC switch output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
2.1.4
BLD, VBAT low voltage detect output (open drain) . . . . . . . . . . . . . . . . . 12
2.1.5
Active-low RST output (open drain) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
2.1.6
MR, manual reset input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
2.1.7
PFO, power-fail output (open drain) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
2.1.8
PFI, power-fail input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
2.1.9
VREF, reference voltage output (1.237, typ) . . . . . . . . . . . . . . . . . . . . . . 12
2.1.10
VOUT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
VTPU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
2.1.11
2.1.12
3
4
2.1.14
VSS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
3.1
Reset input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
3.2
Push-button reset input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
3.3
Backup battery switchover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
3.4
Power-fail input/output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
3.5
Applications information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
3.6
Negative-going VCC transients and undershoot . . . . . . . . . . . . . . . . . . . . 16
Tamper detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
4.1
2/35
2.1.13
VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
VBAT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Physical . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
STM1403
Contents
4.2
Supply voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
5
Typical operating characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
6
Maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
7
DC and AC parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
8
Package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
9
Part numbering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
10
Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
3/35
List of tables
STM1403
List of tables
Table 1.
Table 2.
Table 3.
Table 4.
Table 5.
Table 6.
Table 7.
Table 8.
Table 9.
Table 10.
4/35
Device summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Signal names . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
I/O status in battery backup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Operating and AC measurement condition. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
DC and AC characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Physical and environmental tamper detection levels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
QFN16 – 16-lead, quad, flat package, no lead, 3 x 3 mm body size, mechanical data . . . 31
Ordering information scheme (see Figure 30 on page 33 for marking information) . . . . . . 32
Document revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
STM1403
List of figures
List of figures
Figure 1.
Figure 2.
Figure 3.
Figure 4.
Figure 5.
Figure 6.
Figure 7.
Figure 8.
Figure 9.
Figure 10.
Figure 11.
Figure 12.
Figure 13.
Figure 14.
Figure 15.
Figure 16.
Figure 17.
Figure 18.
Figure 19.
Figure 20.
Figure 21.
Figure 22.
Figure 23.
Figure 24.
Figure 25.
Figure 26.
Figure 27.
Figure 28.
Figure 29.
Figure 30.
Logic diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
QFN16 connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Hardware hookup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Tamper pin (TP1 or TP3) normally high (NH) external hookup (switch closed) . . . . . . . . . . 9
Tamper pin (TP1 or TP3) normally high (NH) external hookup (switch open). . . . . . . . . . . 10
Tamper pin (TP2 or TP4) normally low (NL) external hookup (switch closed) . . . . . . . . . . 10
Tamper pin (TP2 or TP4) normally low (NL) external hookup (switch open). . . . . . . . . . . . 10
Power-fail comparator waveform . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Supply voltage protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
VBAT -to-VOUT on-resistance vs. temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Supply current vs. temperature (no load) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
VPFI threshold vs. temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Reset comparator propagation delay vs. temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Power-up trec vs. temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Normalized reset threshold vs. temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
PFI to PFO propagation delay vs. temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
RST output voltage vs. supply voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
RST response time (assertion) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Power-fail comparator response time (assertion) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Power-fail comparator response time (de-assertion) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
VCC to reset propagation delay vs. temperature. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Maximum transient duration vs. reset threshold overdrive . . . . . . . . . . . . . . . . . . . . . . . . . 22
AC testing input/output waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
MR timing waveform . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
STM1403 switchover diagram, condition A (VBAT < VSW) . . . . . . . . . . . . . . . . . . . . . . . . . 24
STM1403 switchover diagram, condition B (VBAT > VSW) . . . . . . . . . . . . . . . . . . . . . . . . . 25
QFN16 – 16-lead, quad, flat package, no lead, 3 x 3 mm body size, outline . . . . . . . . . . . 30
QFN16 – 16-lead, quad, flat package, no lead, 3 x 3 mm, recommended footprint . . . . . . 31
Topside marking information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
5/35
Description
1
STM1403
Description
The STM1403 family of security supervisors are a low power family of intrusion (tamper)
detection chips targeted at manufacturers of POS terminals and other systems, to enable
them to meet physical and/or environmental intrusion monitoring requirements as
mandated by various standards, such as Federal Information Processing Standards (FIPS)
Pub 140 entitled “Security Requirements for Cryptographic Modules,” published by the
National Institute of Standards and Technology, U.S. Department of Commerce), EMVCo,
ISO, ZKA, and VISA PED. STM1403 supports target levels 3 and lower.
The STM1403 includes automatic battery switchover, RST output (open drain), manual
(push-button) reset input (MR), power-fail comparator (PFI/PFO), physical and/or
environmental tamper detect/security alarm, and battery low voltage detect features.
The STM1403A also offers a VREF (1.237 V) as an option on pin 9. On the STM1403B/C,
this pin is VTPU (internally switched VCC or VBAT).
1.1
VOUT pin modes
The STM1403 is available in three versions, corresponding to three modes of the VOUT pin
(supply voltage out), when the SAL (security alarm) is asserted (active-low) upon tamper
detection:
1.1.1
STM1403A
VOUT stays ON (at VCC or VBAT) when SAL is driven low (activated).
1.1.2
STM1403B
VOUT is set to High-Z when SAL is driven low (activated).
1.1.3
STM1403C
VOUT is driven to ground when SAL is activated (may be used when VOUT is connected
directly to the VCC pin of the external SRAM that holds the cryptographic codes).
All variants (see Table 1: Device summary) are pin-compatible and available in a securityfriendly, low profile, 16-pin QFN package.
6/35
STM1403
Description
Figure 1.
Logic diagram
VREF
BLD(3) or VBAT VCC
VTPU(1)
VCCSW(2)
VOUT
RST(3)
MR
STM1403
PFI
PFO(3)
TP1 (NH)
SAL(3)
TP2 TP3
(NL) (NH)
TP4 VSS
(NL)
AI09682
1. VREF only for STM1403A; VTPU for STM1403B/C.
2. Normal mode: low when VOUT is internally switched to VCC and high when VOUT is internally switched to
battery.
3. SAL, RST, PFO, and BLD are open drain.
Table 2.
Signal names
Vccsw(1)
VCC switch output
MR
Manual (push-button) reset input
PFI
Power-fail Input
TP1 - TP4
Independent physical tamper detect pins 1 through 4
VOUT
Supply voltage output
RST
(2)
PFO(2)
(2)
SAL
BLD(2)
Active-low reset output
Power-fail output
Security alarm output
Battery low voltage detect
VREF
(3)
1.237 V reference voltage
VTPU
(3)
Tamper pull-up (VCC or VBAT)
VBAT
Backup supply voltage
VCC
Supply voltage
VSS
Ground
1. Normal mode: low when VOUT is internally switched to VCC and high when VOUT is internally switched to
battery.
2. SAL, RST, PFO, and BLD are open drain.
3. VREF only for STM1403A; VTPU for STM1403B/C.
Note:
See Section 2: Pin descriptions on page 11 for details.
7/35
Description
STM1403
Figure 2.
QFN16 connections
BLD(2) PFI VCCSW(1) VCC
15
14
RST(2)
1
13
12
VOUT
MR
2
11
VBAT
SAL(2)
3
10
PFO(2)
VSS
4
16
5
6
TP1 TP2 TP3
(NH) (NL) (NH)
Note:
8
7
9
TP4
(NL)
VREF or VTPU(3)
AI09683
See Section 2: Pin descriptions on page 11 for details.
1. Normal mode: low when VOUT is internally switched to VCC and high when VOUT is internally switched to
battery.
2. SAL, RST, PFO, and BLD are open drain.
3. VREF only for STM1403A; VTPU for STM1403B/C
Figure 3.
Block diagram
VCC
VOUT
BAT54J(1,2)
COMPARE
VSO
VBAT(1)
VCCSW
VINT
COMPARE
VRST
trec
Generator
MR
PFI
RST(3)
VPFI
COMPARE
PFO(3)
VDET
COMPARE @
POWER-UP
BLD(3)
VTPU(4)
1.237V VREF
Generator
VHV
COMPARE
VLV
COMPARE
TP1 (NH)
TP2 (NL)
TP3 (NH)
TP4 (NL)
VREF(4)
SAL(3)
AI09684
1. BAT54J (from STMicroelectronics) recommended
2. Required for battery-reverse charging protection
3. Open drain
4. VREF only for STM1403; VTPU for STM1403B/C
8/35
STM1403
Description
Figure 4.
Hardware hookup
VCCSW
Regulator
Unregulated
Voltage
VIN
VCC
VCC
(1)
VCC
VOUT
VCC
C
0.1μF
(2)
STM1403
LPSRAM
R1
PFI
PFO(3)
To Microprocessor NMI
MR
RST(3)
To Microprocessor Reset
VBAT
BLD(3)
To Microprocessor
R2
Push-Button
BAT54J(4)
1.0μF
TP1
TP2
From Actuator Device
(e.g., Switches, Wire Mesh)
TP3
SAL(3)
TP4
VREF(5)
or
VTPU
To ADC
To Physical Tamper Pins TPX
AI09690
1. Normal mode: low when VOUT is internally switched to VCC and high when VOUT is internally switched to
battery.
2. Capacitor (C) is typically ≥ 10 µF.
3. Open drain
4. Diode is required for battery reverse charge protection.
5. VREF only for STM1403; VTPU for STM1403B/C.
Figure 5.
Tamper pin (TP1 or TP3) normally high (NH) external hookup (switch
closed)
VOUT (STM1403A)
or
VTPU (STM1403B/C)
Switch Normally Closed;
Tamper Detection on Open
TP1 or TP3
R(1)
AI09698
1. R typical is 10 MΩ. Resistors must be protected against conductive materials.
9/35
Description
STM1403
Figure 6.
Tamper pin (TP1 or TP3) normally high (NH) external hookup (switch
open)
VOUT (STM1403A)
or
VTPU (STM1403B/C)
(1)
R
TP1 or TP3
Switch Normally Open
Tamper Detection when Closed
AI10461
1. R typical is 10MΩ. Resistors must be protected against conductive materials.
Figure 7.
Tamper pin (TP2 or TP4) normally low (NL) external hookup (switch
closed)
VOUT (STM1403A)
or
VTPU (STM1403B/C)
R(1)
TP2 or TP4
Switch Normally Closed;
Tamper Detection on Open
AI09699
1. R typical is 10 MΩ. Resistors must be protected against conductive materials.
Figure 8.
Tamper pin (TP2 or TP4) normally low (NL) external hookup (switch open)
VOUT (STM1403A)
or
VTPU (STM1403B/C)
Switch Normally Open;
Tamper Detection when Closed
TP2 or TP4
R(1)
AI10462
1. R typical is 10 MΩ. Resistors must be protected against conductive materials.
10/35
STM1403
2
Pin descriptions
Pin descriptions
See Figure 1: Logic diagram and Table 2: Signal names for a brief overview of the signals
connected to this device.
2.1
SAL, security alarm output (open drain)
This signal can be generated when ANY of the following conditions occur:
Note:
2.1.1
●
VINT > VHV, where VHV = upper voltage trip limit (4.2 V typ); and where VINT = VCC or
VBAT;
●
VINT < VLV, where VLV = lower voltage trip limit (2.0 V typ); and where VINT = VCC or
VBAT; or
●
When any of the physical tamper inputs, TP1 to TP4, change from their normal states to
the opposite (i.e., intrusion of a physical enclosure).
1
The default state of the SAL output during initial power-up is undetermined.
2
The alarm function will operate either with VCC on or when the part is internally switched
from VCC to VBAT.
TP1, TP3
Physical tamper detect pin set normally to high (NH). They are connected externally through
a closed switch or a high-impedance resistor to VOUT (in the case of STM1403A) or VTPU (in
the case of STM1403B/C. A tamper condition will be detected when the input pin is pulled
low (see Figure 5 and Figure 6). If not used, tie the pin to VOUT (for STM1403A) or VTPU (for
STM1403B/C).
2.1.2
TP2, TP4
Physical tamper detect pin set normally to low (NL). They are connected externally through
a high-impedance resistor or a closed switch to VSS. A tamper condition will be detected
when the input pin is pulled high (see Figure 7 and Figure 8). If not used, tie the pin to VSS.
2.1.3
Vccsw, VCC switch output
This output is low when VOUT (see Section 2.1.10: VOUT on page 13) is internally switched
to VCC; in this mode it may be used to turn on an external p-channel MOSFET switch which
can source an external device directly from VCC for currents greater than 80 mA (bypassing
the STM1403).
This pin goes high when VOUT is internally switched to VBAT and may be used as a “BATT
ON” indicator.
If a security alarm (SAL) is issued on tamper, then the state of the Vccsw pin is as follows:
11/35
Pin descriptions
2.1.4
STM1403
1.
STM1403A (VOUT remains ON when SAL is active-low): Vccsw pin will continue to
operate in normal mode;
2.
STM1403B (VOUT is taken to High-Z when SAL is active-low): Vccsw pin will be set to
high when this occurs; and
3.
STM1403C (VOUT is driven to ground when SAL is active-low): Vccsw pin will be set to
high when this occurs.
BLD, VBAT low voltage detect output (open drain)
This is an internally loaded test of the battery, activated only during a power-up sequence to
insure that the battery is good either prior to or after encapsulation of the module. There are
three customer options for VDET:
●
2.3 V (2.5 V – external diode drop of about 0.2 V) for a 3 V lithium cell
●
2.5 V (2.7 V – 0.2 V) for a 3 V lithium cell or
●
3.2 V (3.4 V – 0.2 V) for a 3.68 V lithium “AA” battery
This output pin will go active-low when it detects a voltage on the VBAT pin below VDET. BLD
will be released when VCC drops below VRST.
2.1.5
Active-low RST output (open drain)
Goes low and stays low when VCC drops below VRST (reset threshold selected by the
customer), or when MR is logic low. It remains low for trec (200ms, typical) AFTER VCC rises
above VRST and MR goes from low to high.
2.1.6
MR, manual reset input
A logic low on MR asserts the RST output. The RST output remains asserted as long as MR
is low and for trec after MR returns to high. This active low input has an internal 40 kΩ
(typical) pull-up resistor. It can be driven from a TTL or CMOS logic line or shorted to ground
with a switch. Leave it open if unused.
2.1.7
PFO, power-fail output (open drain)
When PFI is less than VPFI (power-fail input threshold voltage) or VCC falls below VSW
(battery switchover threshold ~ 2.4 V), PFO goes low, otherwise, PFO remains high. Leave
this pin open if unused.
2.1.8
PFI, power-fail input
When PFI is less than VPFI, or when VCC falls below VSW (see PFO, above), PFO goes
active-low. If this function is unused, connect this pin to VSS.
2.1.9
VREF, reference voltage output (1.237, typ)
This is valid only when VCC is between 2.4 V and 3.6 V. When VCC falls below 2.4 V (VSW),
VREF is pulled to ground with an internal 100 kΩ resistor. This is an optional feature
available on the STM1403A. On the STM1403B/C, this pin is VTPU (internally switched VCC
or VBAT). If unused, this pin should float.
12/35
STM1403
2.1.10
Pin descriptions
VOUT
This is the supply voltage output. When VCC rises above VSO (battery backup switchover
voltage), VOUT is supplied from VCC. In this condition, VOUT may be connected externally to
VCC through a p-channel MOSFET switch. When VCC falls below the lower value of VSW
(~2.4 V), or VBAT, VOUT is supplied from VBAT. It is recommended that the VOUT pin be
connected externally to a capacitor that will retain a charge for a period of time, in case an
intruder forces VCC or VBAT to ground. The rectifying diode connected from the positive
terminal of the battery to the VBAT pin of the STM1403 will prevent discharge of the
capacitor.
Three variations of parts will be offered with the following options:
2.1.11
1.
STM1403A: VOUT remains ON when SAL is active-low; Vccsw pin will continue to
operate in normal mode (see Section 2.1.3: Vccsw, VCC switch output on page 11);
2.
STM1403B: VOUT is taken to High-Z when SAL is active-low; Vccsw pin will be set to
high when this occurs; and
3.
STM1403C: VOUT is driven to ground when SAL is active-low; Vccsw pin will be set to
high when this occurs.
VTPU
For STM1403B and STM1403C, this pin provides pull-up voltage for the physical tamper
pins (TP1-4). This pin is not to be used as voltage supply source for any other purpose.
Note:
VTPU is the internally switched supply voltage from either the VCC pin or the VBAT pin.
2.1.12
VCC
This is the supply voltage (2.2 V to 3.6 V).
2.1.13
VBAT
This is the secondary (backup battery) supply voltage. The pin is connected to the positive
terminal of the battery with a rectifying diode like the BAT54J from STMicroelectronics for
reverse charge protection. Voltage at this pin, after diode rectification, will be approximately
0.2 V less than the battery voltage, and will depend on the type of battery used as well as
the IBAT being drawn. (A capacitor of at least 1.0 µF connected between the VBAT pin and
VSS is required.) If no battery is used, connect the VBAT pin to the VCC pin.
2.1.14
VSS
Ground, VSS, is the reference for the power supply. It must be connected to system ground.
13/35
Operation
STM1403
3
Operation
3.1
Reset input
The STM1403 security supervisor asserts a reset signal to the MCU whenever VCC goes
below the reset threshold (VRST), or when the push-button reset input (MR) is taken low.
RST is guaranteed to be a logic low for 0V < VCC < VRST if VBAT is greater than 1V. Without
a backup battery, RST is guaranteed valid down to VCC =1V.
During power-up, once VCC exceeds the reset threshold an internal timer keeps RST low for
the reset time-out period, trec. After this interval RST returns high.
If VCC drops below the reset threshold, RST goes low. Each time RST is asserted, it stays
low for at least the reset time-out period (trec). Any time VCC goes below the reset threshold
the internal timer clears. The reset timer starts when VCC returns above the reset threshold.
3.2
Push-button reset input
A logic low on MR asserts reset. Reset remains asserted while MR is low, and for trec (see
Figure 25 on page 24) after it returns high. The MR input has an internal 40 kΩ pull-up
resistor, allowing it to be left open if not used. This input can be driven with TTL/CMOS-logic
levels or with open-drain/collector outputs. Connect a normally open momentary switch from
MR to ground to create a manual reset function; external debounce circuitry is not required.
If MR is driven from long cables or the device is used in a noisy environment, connect a
0.1 µF capacitor from MR to VSS to provide additional noise immunity. MR may float, or be
tied to VCC when not used.
3.3
Backup battery switchover
In the event of a power failure, it may be necessary to preserve the contents of external
SRAM through VOUT. With a backup battery installed with voltage VBAT, the devices
automatically switch the SRAM to the backup supply when VCC falls.
Note:
If backup battery is not used, connect both VBAT and VOUT to VCC.
This family of security supervisors does not always connect VBAT to VOUT when VBAT is
greater than VCC. VBAT connects to VOUT (through a 100 Ω switch) when VCC is below VSW
(~2.4 V) or VBAT (whichever is lower). This is done to allow the backup battery (e.g., a 3.6 V
battery) to have a higher voltage than VCC.
Assuming that VBAT > 2.0 V, switchover at VSO ensures that battery backup mode is entered
before VOUT gets too close to the 2.0 V minimum required to reliably retain data in most
external SRAMs. When VCC recovers, hysteresis is used to avoid oscillation around the VSO
point. VOUT is connected to VCC through a 3 Ω PMOS power switch.
Note:
14/35
The backup battery may be removed while VCC is valid, assuming VBAT is adequately
decoupled (0.1 µF typ), without danger of triggering a reset.
STM1403
Operation
Table 3.
I/O status in battery backup
Pin
VOUT
Connected to VBAT through internal switch
VCC
Disconnected from VOUT
PFI
Disabled
PFO
Logic low
MR
Disabled
RST
Logic low
VBAT
Connected to VOUT
Vccsw
3.4
Status
Logic high
VREF
Pulled to VSS below 2.4 V (VSW)
BLD
Logic high
VTPU
Connected to VBAT through an internal switch
Power-fail input/output
The power-fail input (PFI) is compared to an internal reference voltage (independent from
the VRST comparator). If PFI is less than the power-fail threshold (VPFI), the power-fail
output (PFO) will go low. This function is intended for use as an undervoltage detector to
signal a failing power supply. Typically PFI is connected through an external voltage divider
(see Figure 4 on page 9) to either the unregulated DC input (if it is available) or the
regulated output of the VCC regulator. The voltage divider can be set up such that the
voltage at PFI falls below VPFI several milliseconds before the regulated VCC input to the
STM1403 or the microprocessor drops below the minimum operating voltage.
During battery backup, the power-fail comparator is turned off and PFO goes (or remains)
low (see Figure 9 on page 16). This occurs after VCC drops below VSW (~2.4V). When
power returns, the power-fail comparator is enabled and PFO follows PFI. If the comparator
is unused, PFI should be connected to VSS and PFO left unconnected. PFO may be
connected to MR so that a low voltage on PFI will generate a reset output.
3.5
Applications information
These supervisor circuits are not short-circuit protected. Shorting VOUT to ground excluding power-up transients such as charging a decoupling capacitor - destroys the
device. Decouple both VCC and VBAT pins to ground by placing 0.1 µF capacitors as close to
the device as possible.
15/35
Operation
STM1403
Figure 9.
Power-fail comparator waveform
VCC
VRST
VSW (2.4V)
trec
PFO
PFO follows PFI
PFO follows PFI
RST
AI08861a
3.6
Negative-going VCC transients and undershoot
The STM1403 devices are relatively immune to negative-going VCC transients (glitches).
Figure 23 on page 22 was generated using a negative pulse applied to VCC, starting at VRST
+ 0.3 V and ending below the reset threshold by the magnitude indicated (comparator
overdrive). The graph indicates the maximum pulse width a negative VCC transient can have
without causing a reset pulse. As the magnitude of the transient increases (further below the
threshold), the maximum allowable pulse width decreases. Any combination of duration and
overdrive which lies under the curve will NOT generate a reset signal. Typically, a VCC
transient that goes 100 mV below the reset threshold and lasts 40 µs or less will not cause a
reset pulse. A 0.1 µF bypass capacitor mounted as close as possible to the VCC pin
provides additional transient immunity (see Figure 10).
In addition to transients that are caused by normal SRAM operation, power cycling can
generate negative voltage spikes on VCC that drive it to values below VSS by as much as
one volt. These negative spikes can cause data corruption in the SRAM while in battery
backup mode. To protect from these voltage spikes, STMicroelectronics recommends
connecting a schottky diode from VCC to VSS (cathode connected to VCC, anode to VSS).
Schottky diode 1N5817 is recommended for through hole and MBRS120T3 is
recommended for surface mount.
Figure 10. Supply voltage protection
VCC
VCC
0.1μF
DEVICE
VSS
AI02169
16/35
STM1403
Tamper detection
4
Tamper detection
4.1
Physical
There are four (4) high-impedance physical tamper detect input pins, 2 normally set to high
(NH) and 2 normally set to low (NL). Each input is designed with a glitch immunity (see
Table 7 on page 28). These inputs can be connected externally to several types of actuator
devices (e.g., switches, wire mesh). A tamper on any one of the four inputs that causes its
state to change will trigger the security alarm (SAL) and drive it to active-low. Once the
tamper condition no longer exists, the SAL will return to its normal high state.
TP1 and TP3 are set normally to high (NH). They are connected externally through a closed
switch or a high-impedance resistor to VOUT (in the case of STM1403A) or VTPU (in the case
of STM1403B/C), A tamper condition will be detected when the input pin is pulled low (see
Figure 5 and Figure 6). If not used, tie the pin to VOUT or VTPU.
TP2 and TP4 are set normally to low (NL). They are connected externally through a highimpedance resistor or a closed switch to VSS. A tamper condition will be detected when the
input pin is pulled high (see Figure 7 and Figure 8). If not used, tie the pin to VSS.
4.2
Supply voltage
The internally switched supply voltage, VINT (either VCC input or VBAT input) is continuously
monitored. If VINT should exceed the over voltage trip point, VHV (set at 4.2V, typical), or
should go below the under voltage trip point, VLV (set at 2.0 V, typical). SAL will be driven
active-low. Once the tamper condition no longer exists, the SAL pin will return to its normal
high state.
When no tamper condition exists, SAL is normally high (see Section 2: Pin descriptions on
page 11).
When a tamper is detected, the SAL is activated (driven low), independent of the part type.
VOUT can be driven to one of three states, depending on which variant of STM1403 is being
used (see Table 1: Device summary on page 1):
Note:
●
ON
●
High-Z or
●
Ground (VSS)
The STM1403 must be initially powered above VRST to enable the tamper detection alarms.
For example, if the battery is on while VCC = 0V, no alarm condition can be detected until
VCC rises above VRST (and trec expires). From this point on, alarms can be detected either
on battery or VCC. This is done to avoid false alarms when the device goes from no power to
its operational state.
17/35
Typical operating characteristics
STM1403
5
Typical operating characteristics
Note:
Typical values are at TA = 25°C.
VBAT - to - VOUT ON-RESISTANCE [Ω]
Figure 11. VBAT -to-VOUT on-resistance vs. temperature
220
VCC = 0V
200
VBAT = 2V
180
VBAT = 3V
160
VBAT = 3.3V
140
120
100
–60
–40
–20
0
20
40
60
80
100
120
TEMPERATURE [°C]
140
AI09691
Figure 12. Supply current vs. temperature (no load)
30
Supply Current [µA]
25
20
2.5V
3.3V
15
3.6V
10
5
0
–50
–40
–30
–20
–10
0
10
20
30
40
TEMPERATURE [°C]
18/35
50
60
70
80
90
100
AI09692
STM1403
Typical operating characteristics
Figure 13. VPFI threshold vs. temperature
VPFI THRESHOLD [V]
1.255
1.250
1.245
VCC = 3.3V
1.240
1.235
VCC = 2.5V
1.230
VBAT = 3.0V
1.225
–50
–30
–10
10
30
50
70
90
110
TEMPERATURE [°C]
130
AI09693
PROPAGATION DELAY [µs]
Figure 14. Reset comparator propagation delay vs. temperature
24
22
VBAT = 3.0V
100mV OVERDRIVE
20
18
16
14
12
10
–60
–40
–20
0
20
40
60
80
100
TEMPERATURE [°C]
AI09143
Figure 15. Power-up trec vs. temperature
215
trec [ms]
210
205
200
195
–50
–30
–10
10
30
50
TEMPERATURE [°C]
70
90
110
130
AI09144
19/35
Typical operating characteristics
STM1403
NORMALIZED RESET THRESHOLD
[V]
Figure 16. Normalized reset threshold vs. temperature
1.002
1.000
0.998
0.996
VBAT = 3.0V
0.994
–60
–40
–20
0
20
40
60
80
100
TEMPERATURE [°C]
120
140
AI09145
Figure 17. PFI to PFO propagation delay vs. temperature
9
PROPAGATION DELAY [µs]
8
7
6
5
4
3
2
1
0
–60
–40
–20
0
20
40
60
TEMPERATURE [°C]
80
100
120
140
AI09148
Figure 18. RST output voltage vs. supply voltage
3.5
RST OUTPUT VOLTAGE [V]
3.0
2.5
VCC
2.0
VRST
1.5
1.0
0.5
0
500 ms/div
20/35
AI09149b
STM1403
Typical operating characteristics
Figure 19. RST response time (assertion)
4.0
VCC LEVEL [V]
3.0
VCC
2.0
VRST
1.0
0.0
2 µs/div
AI09151b
Figure 20. Power-fail comparator response time (assertion)
1.45
4.0
1.40
1.35
PFO
1.30
2.0
PFI
1.25
VPFI LEVEL [V]
VPFO LEVEL [V]
3.0
1.0
1.20
0.0
1.15
2µs/div
AI09153b
Figure 21. Power-fail comparator response time (de-assertion)
1.45
4.0
3.5
1.40
1.35
2.5
PFO
1.30
2.0
1.5
PFI
1.25
VPFI LEVEL (V)
VPFO LEVEL (V)
3.0
1.0
1.20
0.5
1.15
0.0
2 µs/div
AI09154
21/35
Typical operating characteristics
STM1403
Figure 22. VCC to reset propagation delay vs. temperature
PROPAGATION DELAY [µs]
60
50
40
10V/ms
30
1V/ms
0.25V/ms
20
10
0
–60
–40
–20
0
20
40
60
80
100
TEMPERATURE [°C]
AI09155
Figure 23. Maximum transient duration vs. reset threshold overdrive
TRANSIENT DURATION [µs]
250
200
150
100
50
0
1
10
100
1000
RESET COMPARATOR OVERDRIVE, VRST – VCC [mV]
22/35
10000
AI09156
STM1403
6
Maximum ratings
Maximum ratings
Stressing the device above the rating listed in the absolute maximum ratings table may
cause permanent damage to the device. These are stress ratings only and operation of the
device at these or any other conditions above those indicated in the Operating sections of
this specification is not implied. Exposure to absolute maximum rating conditions for
extended periods may affect device reliability. Refer also to the STMicroelectronics SURE
Program and other relevant quality documents.
Table 4.
Absolute maximum ratings
Symbol
Value
Unit
TSTG
Storage temperature (VCC off, VBAT off)
–55 to 150
°C
TSLD(1)
Lead solder temperature for 10 seconds
260
°C
–0.3 to VCC +0.3
V
VIO
Note:
Parameter
Input or output voltage
VCC/VBAT
Supply voltage
–0.3 to 4.5
V
IO
Output current
20
mA
PD
Power dissipation
320
mW
Reflow at peak temperature of 255°C to 260°C for < 30 seconds (total thermal budget not to
exceed 180°C for between 90 to 150 seconds).
23/35
DC and AC parameters
7
STM1403
DC and AC parameters
This section summarizes the operating measurement conditions, and the DC and AC
characteristics of the device. The parameters in the DC and AC characteristics Tables that
follow, are derived from tests performed under the Measurement Conditions summarized in
Table 5: Operating and AC measurement condition. Designers should check that the
operating conditions in their circuit match the operating conditions when relying on the
quoted parameters.
Table 5.
Operating and AC measurement condition
Parameter
STM1403
Unit
VCC/VBAT supply voltage
2.2 to 3.6
V
Ambient operating temperature (TA)
–40 to 85
°C
≤5
ns
Input pulse voltages
0.2 to 0.8VCC
V
Input and output timing ref. voltages
0.3 to 0.7VCC
V
Input rise and fall times
Figure 24. AC testing input/output waveforms
0.8VCC
0.7VCC
0.3VCC
0.2VCC
AI02568
Figure 25. MR timing waveform
MR
tMLRL
RST
tMLMH
trec
AI09694
Figure 26. STM1403 switchover diagram, condition A (VBAT < VSW)
VCC = 3.3V
VRST
VSW = 2.4V
VBAT
VBAT – 75mV
VOUT
VBAT – 35mV
AI10463
Figure 27. STM1403 switchover diagram, condition B (VBAT > VSW)
VCC = 3.3V
VOUT
VBAT
VSW = 2.4V
VSW + 40mV
AI10464
24/35
STM1403
Table 6.
Sym
VCC,
VBAT(2)
DC and AC parameters
DC and AC characteristics
Alternative
Description
Operating voltage
Test condition(1)
Min
TA = –40 to +85°C
2.2
VCC supply current
(STM1403A)
Typ
Max
Unit
3.6
V
45
60
µA
30
45
µA
Typ @ 3.3 V, 25°C
ICC
IBAT(3)
VOUT1
VOUT2
VCC supply current
(STM1403B,C)
VCC supply current in
battery backup mode
Excluding IOUT
(VBAT = 2.3 V, VCC = 2.0
V, MR = VCC)
25
35
µA
VBAT supply current in
battery backup mode
Excluding IOUT
(VBAT = 3.6 V)
2.8
4.0
µA
VOUT voltage (active)
VOUT voltage (battery
backup)
IOUT1 = 5 mA(4)
(VCC > VSW)
VCC –
0.03
VCC –
0.015
V
IOUT1 = 80 mA
(VCC > VSW)
VCC –
0.3
VCC –
0.15
V
IOUT1 = 250 µA,
VCC > VSW(4)
VCC –
0.0015
VCC –
0.0006
V
IOUT2 = 250 µA,
VBAT = 2.2 V
VBAT –
0.1
VBAT –
0.04
V
VBAT –
0.16
V
IOUT2 = 1 mA,
VBAT = 2.2 V
VTPU1
Internal switched supply
voltage (active)
ISOURCE = 500 µA
(VCC > VSW)
VTPU2
Internal switched supply
voltage (battery backup)
ISOURCE = 100 µA
(VBAT = 2.2 V)
ILI
V
VBAT –
0.10
V
Input leakage current (MR)
MR = 0 V; VCC = 3 V
20
75
350
µA
Input leakage current (PFI)
0 V = VIN = VCC
–25
2
+25
nA
Input leakage current
(TP1-TP4)
0 V = VIN = VCC
–1
+1
µA
0 V = VIN = VCC(5)
–1
+1
µA
ILO
Output leakage current
VIH
Input high voltage (MR)
VIL
Input low voltage (MR)
VOL
Output low voltage (PFO,
RST, Vccsw, SAL, BLD)
Output low voltage (RST)
VOL
VCC –
0.3
VRST (max) < VCC < 3.6V
0.7VCC
V
0.3VCC
V
VCC = VRST (max),
ISINK = 3.2mA
0.3
V
IOL = 40µA; VCC = 1.0V;
VBAT = VCC;
TA = 0°C to 85°C
0.3
V
IOL = 200µA;
VCC = 1.2V; VBAT = VCC
0.3
V
25/35
DC and AC parameters
Table 6.
Sym
VOHB
STM1403
DC and AC characteristics (continued)
Alter-
Description
Test condition(1)
Min
VOH battery backup (Vccsw)
ISOURCE = 100 µA,
0.8VBAT
native
Pull-up supply voltage
(open drain)
Typ
Max
Unit
V
RST, SAL, BLD, PFO
3.6
V
1.237
1.262
V
10
20
mV
Power-fail comparator
VPFI
tPFD
PFI input threshold
PFI falling (VCC < 3.6 V)
PFI hysteresis
PFI Rising (VCC < 3.6 V)
1.212
PFI to PFO propagation
delay
2
µs
VBAT > VSW
VSW
V
VBAT < VSW
VBAT
V
VBAT > VSW
VSW
V
VBAT < VSW
VBAT
V
VSW
2.4
V
Hysteresis
40
mV
Battery switchover
Battery backup
switchover voltage (6)(7)
Powerdown
Power-up
VSO
Battery low voltage detect
VDET
Battery detect threshold
M
2.25
2.30
2.34
V
N
2.45
2.50
2.55
V
O
3.14
3.20
3.26
V
0°C to 85°C
1.212
1.237
1.262
V
–40° to 0°C
1.200
1.237
1.274
V
0°C to 85°C
15
25
µA
–40° to 0°C
10
15
µA
10
13
µA
10-100
µVrms
On
power-up
only
Voltage reference (option for STM1403A)(8)
VREF
Voltage reference
(see Section 2.1.9: VREF,
reference voltage output
(1.237, typ) on page 12)
IREF+
Source current
IREF–
Sink current
Vn
26/35
Output voltage noise
f = 100 Hz to 100 kH
STM1403
Table 6.
Sym
DC and AC parameters
DC and AC characteristics (continued)
Alter-
Description
native
Test condition(1)
Min
Typ
Max
Unit
VCC falling
3.00
3.075
3.15
V
VCC rising
3.00
3.085
3.17
V
VCC falling
2.85
2.925
3.00
V
VCC rising
2.85
2.935
3.02
V
VCC falling
2.55
2.625
2.70
V
VCC rising
2.55
2.635
2.72
V
140
200
280
ms
Reset thresholds
T
VRST(9)
Reset threshold
S
R
trec
RST pulse width
Push-button reset input
tMLMH
tMR
MR pulse width
tMLRL
tMRD
MR to RST output delay
100
ns
60
500
ns
1. Valid for ambient operating temperature: TA = –40 to 85°C; VCC = VRST (max) to 3.6 V; and VBAT = 2.8 V (except where
noted); typical values are for 3.3 V and 25°C.
2. VCC supply current, logic input leakage, push-button reset functionality, PFI functionality, state of RST tested at
VBAT = 3.6 V, and VCC = 3.6 V. The state of RST and PFO is tested at VCC = VCC (min). VBAT is voltage measured at the
pin.
3. Tested at VBAT = 3.6 V, VCC = 3.5 V and 0 V.
4. Guaranteed by design.
5. The leakage current measured on the RST, SAL, PFO, and BLD pins are tested with the output not asserted (output high
impedance).
6. When VBAT > VCC > VSW, VOUT remains connected to VCC until VCC drops below VSW.
7. When VSW > VCC > VBAT, VOUT remains connected to VCC until VCC drops below the battery voltage (VBAT) – 75 mV.
8. Maximum external capacitive load on VREF pin cannot exceed 1nF.
9. The reset threshold tolerance is wider for VCC rising than for VCC falling due to the 10 mV (typ) hysteresis, which prevents
internal oscillation.
27/35
DC and AC parameters
Table 7.
STM1403
Physical and environmental tamper detection levels
Sym
Parameter
VHV
VLV
Test
conditions(1)
Min
Typ
Max
Unit
Overvoltage trip level
4.0
4.2
4.4
V
Undervoltage trip level
1.9
2.0
2.1
V
25
50
µs
SAL propagation delay time
(after over/under voltage
detection)
VHV + 200 mV or
VLV – 200 mV
VHTP
Trip point for NH physical
tamper input pins (TP1 or TP3)
VOUT –
1.3 V(2)
VOUT –
0.3 V(2)
V
VLTP
Trip point for NL physical
tamper input pins (TP2 or TP4)
0.3
1.0
V
50
µs
SAL propagation delay time(3)
(after physical tamper pin
detection)
Physical tamper input (TPX)
glitch immunity
VHTP =
VOUT/VTPU;
VLTP = VSS
VDD = 3.6
30
15
µs
1. Valid for ambient operating temperature: TA = –40 to 85°C; VCC = VLV to VHV (except where noted).
2. In the case of STM1403A, physical tamper input pins (TPX) are referenced to VOUT (pin 12). In the case of
STM1403B or C, TPX are referenced to VTPU pin (pin 9).
3. VCC = VRST (max) to 3.6 V
28/35
STM1403
8
Package mechanical data
Package mechanical data
In order to meet environmental requirements, ST offers these devices in ECOPACK®
packages. These packages have a Lead-free second level interconnect. The category of
second Level Interconnect is marked on the package and on the inner box label, in
compliance with JEDEC Standard JESD97.
The maximum ratings related to soldering conditions are also marked on the inner box label.
ECOPACK is an ST trademark. ECOPACK specifications are available at: www.st.com.
Figure 28. QFN16 – 16-lead, quad, flat package, no lead, 3 x 3 mm body size, outline
D
E
A3
A
A1
ddd C
e
b
L
K
1
2
E2
Ch
3
K
D2
QFN16-A
Note:
Drawing is not to scale.
29/35
Package mechanical data
Table 8.
STM1403
QFN16 – 16-lead, quad, flat package, no lead, 3 x 3 mm body size,
mechanical data
mm
inches
Symb
Typ
Min
Max
Typ
Min
Max
A
0.90
0.80
1.00
0.035
0.032
0.039
A1
0.02
0.00
0.05
0.001
0.000
0.002
A3
0.20
–
–
0.008
–
–
b
0.25
0.18
0.30
0.010
0.007
0.012
D
3.00
2.90
3.10
0.118
0.114
0.122
D2
1.70
1.55
1.80
0.067
0.061
0.071
E
3.00
2.90
3.10
0.118
0.114
0.122
E2
1.70
1.55
1.80
0.067
0.061
0.071
e
0.50
–
–
0.020
–
–
K
0.20
–
–
0.008
–
–
L
0.40
0.30
0.50
0.016
0.012
0.020
ddd
–
0.08
–
–
0.003
–
Ch
–
0.33
–
–
0.013
–
N
16
16
Figure 29. QFN16 – 16-lead, quad, flat package, no lead, 3 x 3 mm, recommended
footprint
1.60
3.55
AI09126
Note:
30/35
Substrate pad should be tied to VSS.
2.0
0.28
STM1403
Part numbering
9
Part numbering
Table 9.
Ordering information scheme (see Figure 30 on page 32 for marking information)
Example:
STM1403
A
T
M
Q
6
F
Device type
STM1403: physical, voltage tamper detect
VOUT status (SAL = active-low)
A: VOUT = ON; Vccsw = normal mode
B(1): VOUT = High-Z; Vccsw = high
C: VOUT = ground; Vccsw = high
Reset threshold voltage
T: VRST = 3.00 V to 3.15 V
S: VRST = 2.85 V to 3.00 V
R: VRST = 2.55 V to 2.70 V
Battery low voltage detect threshold (VDET)
M: VDET = 2.3 V (typ)
N: VDET = 2.5 V (typ)
O: VDET = 3.2 V (typ)
Package
Q = QFN16 (3 mm x 3 mm)
Temperature range
6 = –40 to 85°C
Shipping method
F = ECOPACK® package, tape & reel
1. Contact local ST sales office for availability.
For other options, or for more information on any aspect of this device, please contact the ST sales office
nearest you.
31/35
Part numbering
STM1403
Figure 30. Topside marking information
03
XXX(1)
YWW(2)
AI11878
1. Options codes:
X = A, B, or C (for VOUT)
X = T, S, or R (for reset threshold)
X = M, N, or O (for battery low voltage detect threshold)
2. Traceability codes
Y = Year
WW = Work Week
32/35
STM1403
10
Revision history
Revision history
Table 10.
Document revision history
Date
Revision
Changes
11-Oct-2004
1
26-Nov-2004
1.1
Corrected footprint dimensions; update characteristics (Figure 1, 2,
3, 4, 5, 6, 7, 8, 26, 27, 29; Table 1, 2, 3, 6, 7)
22-Dec-2004
1.2
Update characteristics ( Figure 4; Table 6, 7, 9)
03-Feb-2005
1.3
Update characteristics (Figure 4; Table 6, 7)
25-Feb-2005
1.4
Update temperature trip limits (Table 9)
06-May-2005
1.5
Update characteristics (Figure 3, 4, 28; Table 6, 7)
05-Aug-2005
2
Removed STM1404 references (Figure 1, 2, 3, 4, 5, 6, 7, 8, 26, 27;
Table 1, 2, 5, 6, 7, 9)
18-Oct-2005
3
Update hardware hookup, characteristics, Lead-free text; add
marking information (Figure 4, 30; Table 6, 7, 9)
07-Feb-2007
4
Update cover page, Table 7, and part numbering (Table 9).
20-Aug-2008
5
Minor formatting changes, updated Table 1 and 7.
First edition
33/35
STM1403
Please Read Carefully:
Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the
right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any
time, without notice.
All ST products are sold pursuant to ST’s terms and conditions of sale.
Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no
liability whatsoever relating to the choice, selection or use of the ST products and services described herein.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this
document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products
or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such
third party products or services or any intellectual property contained therein.
UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED
WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS
OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.
UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT
RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING
APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY,
DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE
GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK.
Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void
any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any
liability of ST.
ST and the ST logo are trademarks or registered trademarks of ST in various countries.
Information in this document supersedes and replaces all information previously supplied.
The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.
© 2008 STMicroelectronics - All rights reserved
STMicroelectronics group of companies
Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America
www.st.com
35/35