TSC TS754

TS750 THRU TS758
6.0 AMPS. Silicon Rectifiers
Voltage Range
50 to 800 Volts
Current
6.0 Amperes
P600
Features
Plastic material used carries
Underwriters Laboratory Classification
94V-0
High forward current capability
Diffused junction
High surge current capability
High temperature soldering guaranteed:
260OC/10 seconds, 0.375”(9.5mm) lead
length, 5lbs.(2.3kg) tension
Mechanical Data
Cases: Molded plastic body
Lead: Plated axial leads, solderable per
MIL-STD-750, Method 2026
Polarity: Color band denotes cathode end
Mounting position: Any
Weight: 0.07 ounce, 2.1 grams
Dimensions in inches and (millimeters)
Maximum Ratings and Electrical Characteristics
Rating at 25℃ambient temperature unless otherwise specified.
Single phase, half wave,60 Hz, resistive or inductive load.
For capacitive load, derate current by 20%
Symbol TS750 TS751 TS752 TS754 TS756 TS758 Units
Type Number
Maximum Recurrent Peak Reverse Voltage
50
100
200
400
600
800
V
VRRM
Maximum RMS Voltage
VRMS
35
70
140
280
420
560
V
Maximum DC Blocking Voltage
VDC
50
100
200
400
600
800
V
Maximum Non-repetitive Peak Reverse Voltage
VBR
60
120
240
480
720 1200
V
Maximum Average Forward Rectified Current at
TA = 60℃, P.C.B. Mounting (Fig. 1)
TL= 60℃, 0.125”(3.18mm) Lead Length (Fig. 2)
Peak Forward Surge Current, 8.3 ms Single Half
Sine-wave Superimposed on Rated Load (JEDEC
method )
Maximum Instantaneous Forward Voltage @ 6.0A
@ 100A
Maximum DC Reverse Current @ TA=25℃
at Rated DC Blocking Voltage @ TA=100℃
Typical Junction Capacitance ( Note 1 )
Typical Thermal Resistance (Note 2)
Operating Junction Temperature Range
Storage Temperature Range
I(AV)
6.0
22.0
A
IFSM
400
A
VF
IR
Cj
RθJA
RθJL
TJ
TSTG
Notes: 1. Measured at 1.0 MHz and Applied Reverse Voltage of 4.0 Volts
2. Mount on Cu-Pad Size 16mm x 16mm on P.C.B.
- 526 -
0.95
1.25
5.0
1000
150
20.0
4.0
-50 to +150
-50 to +150
1.30
V
uA
uA
pF
℃/W
℃
℃
8.0
FIG.1- MAXIMUM FORWARD CURRENT DERATING
CURVE
60 Hz RESISTIVE OR
INDUCTIVE LOAD
7.0
28
GROUND PLANE
1.0 X 1.0"
(25.4 X 25.4mm)
COPPER
SURFACE AREA
6.0
AVERAGE FORWARD CURRENT. (A)
AVERAGE FORWARD RECTIFIED CURRENT. (A)
RATINGS AND CHARACTERISTIC CURVES (TS750 THRU TS758)
5.0
4.0
0.050"(1.27mm) min.
3.0
ALTERNATE
P.C.B.
2.0
1.1 x 1.0" (30 x 30Mmm)
COPPER PADS
1.0
0
0
20
40
60
80
100
120
140
160
L=0.25"
(6.35mm)
24
L=0.375"
(9.5mm)
16
12
8
4
0
20
40
100
120
140
160
180
200
FIG.4- TYPICAL INSTANTANEOUS FORWARD
CHARACTERISTICS
100
100
10
INSTANTANEOUS FORDWARD CURRENT AMPERES
INSTANTANEOUS REVERSE CURRENT MICROAMPERES
80
LEAD TEMPERATURE. ( C)
FIG.3- TYPICAL REVERSE CHARACTERISTICS
Tj=125 0C
Tj=100 0C
1
Tj=25 0C
0.1
0
20
40
60
80
100
120
10
1
0.1
0
Tj=25 C
PULSE WIDTH-300 S
1% DUTY CYCLE
0.01
0.6
140
TRANSIENT THERMAL IMPEDANCE, OC/W
VRRM may be APPLIED
BETWEEN EACH CYCLE of
SURGE, the Tj NOTED is Tj
PRIOR to SURGE
0
Tj=25 C
100
0.1
1
1.0
1.2
1.4
1.8
1.6
FIG.6- TYPICAL TRANSIENT THERMAL IMPEDANCE
FIG.5- MAXIMUM PEAK FORWARD SURGE CURRENT
600
0.8
INSTANTANEOUS FORWARD VOLTAGE, VOLTS
PERCENT OF RATED PEAK REVERSE VOLTAGE. (%)
PEAK FORWARD SURGE CURRENT AMPERES
60
o
o
0
BOTH LEADS
ATTACHED as HEAT
SINKS WITH
LENGTH as
SHOWN, L
L=0.625" (15.8mm)
AMBIENT TEMPERATURE. ( C)
0.01
60 Hz RESISTIVE OR
INDUCTIVE LOAD
L=0.125" (3.18mm)
20
0
180 200
FIG.2- MAXIMUM FORWARD CURRENT DERATING
CURVE
10
100
10
1
0.1
0.01
0.1
1
T, PULSE DURATION, sec.
NUMBER OF CYCLES AT 60Hz
- 527 -
10
100