1N5400 THRU 1N5408 GENERAL PURPOSE PLASTIC RECTIFIER Reverse Voltage - 50 to 1000 Volts FEATURES DO-201AD ♦ Plastic package has Underwriters Laboratory Flammability Classification 94V-0 ♦ High surge current capability ♦ Construction utilizes void-free molded plastic technique ♦ 3.0 Ampere operation at TL=105°C with no thermal runaway ♦ Typical IR less than 0.1µA ♦ High temperature soldering guaranteed: 250°C/10 seconds, 0.375" (9.5mm) lead length, 5 lbs. (2.3kg) tension 1.0 (25.4) MIN. 0.210 (5.3) 0.190 (4.8) DIA. 0.375 (9.5) 0.285 (7.2) MECHANICAL DATA 0.052 (1.32) 0.048 (1.22) DIA. Forward Current - 3.0 Amperes Case: JEDEC DO-201AD molded plastic body Terminals: Plated axial leads, solderable per MIL-STD-750, Method 2026 Polarity: Color band denotes cathode end Mounting Position: Any Weight: 0.04 ounce, 1.1 grams 1.0 (25.4) MIN. Dimensions in inches and (millimeters) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25°C ambient temperature unless otherwise specified. SYMBOLS 1N 5400 1N 5401 1N 5402 1N 5403 1N 5404 1N 5405 1N 5406 1N 5407 *Maximum repetitive peak reverse voltage VRRM 50 100 200 300 400 500 600 800 1000 Volts *Maximum RMS voltage VRMS 35 70 140 210 280 350 420 560 *Maximum DC blocking voltage to TA=150°C VDC 50 100 200 300 400 500 600 800 1000 Volts *Maximum average forward rectified current 0.5” (12.5mm) lead length at TL=105°C I(AV) 3.0 Amps *Peak forward surge current 8.3ms single half sine-wave superimposed on rated load (JEDEC Method) at TL=105°C IFSM 200.0 Amps *Maximum instantaneous forward voltage at 3.0A VF 1.2 Volts TA=25°C TA=150°C IR 10.0 500.0 µA IR(AV) 500.0 µA CJ 30.0 pF RΘJA 20.0 °C/W TA +150 °C TJ -50 to +170 °C TSTG -50 to +170 °C *Maximum DC reverse current at rated DC blocking voltage *Maximum full load reverse current full cycle average, 0.5" (12.5mm) lead length at TL=105°C Typical junction capacitance (NOTE 1) *Typical thermal resistance (NOTE 2) Maximum DC blocking voltage temperature *Operating junction temperature range *Storage temperature range NOTES: (1) Measured at 1.0 MHz and applied reverse voltage of 4.0 Volts (2) Thermal resistance from junction to ambient at 0.375” (9.5mm) lead length, P.C.B. mounted with 0.8 x 0.8” (20 x 20mm) copper heatsinks *JEDEC registered value 4/98 1N 5408 700 UNITS Volts RATINGS AND CHARACTERISTIC CURVES 1N5400 THRU 1N5408 FIG. 2 - MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT L=0.31” (0.79mm) 7.0 L=0.25” (6.3 mm) TL=LEAD TEMPERATURE with BOTH LEADS HEAT SINK MOUNTED with LENGTH (L) AS SHOWN 6.0 5.0 60 Hz RESISTIVE OR INDUCTIVE LOAD 4.0 L=0.50” (12.7 mm) 3.0 2.0 TA=AMBIENT TEMPERATURE 0.375” (9.5mm) LEAD LENGTH P.C. B. MOUNTING 1.0 0 40 60 80 100 120 140 160 INSTANTANEOUS FORWARD CURRENT, AMPERES 8.0 400 8.3ms SINGLE HALF SINE WAVE (JEDEC Method) TL=105°C 1.0 CYCLE 100 40 1.0 180 100 10 NUMBER OF CYCLES AT 60 HZ TEMPERATURE, °C FIG. 3 - TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS FIG. 4 - TYPICAL REVERSE CHARACTERISTICS 100 INSTANTANEOUS REVERSE CURRENT, MICROAMPERES INSTANTANEOUS FORWARD CURRENT, AMPERES 100 10 TJ=25°C PULSE WIDTH=300µs 1% DUTY CYCLE 1 0.1 10 TJ=150°C 1 TJ=100°C 0.1 TJ=25°C 0.01 0 0.01 0.4 0.6 0.8 1.0 1.2 1.4 1.6 20 40 60 80 100 PERCENT OF RATED PEAK REVERSE VOLTAGE,% 1.8 INSTANTANEOUS FORWARD VOLTAGE, VOLTS 100 70 TJ=25°C f=1.0 MHz Vsig=50mVp-p 10 1 0.1 1 10 REVERSE VOLTAGE, VOLTS 100 TRANSIENT THERMAL IMPEDANCE, °C/W FIG. 6 - TYPICAL TRANSIENT THERMAL IMPEDANCE FIG. 5 - TYPICAL JUNCTION CAPACITANCE JUNCTION CAPACITANCE, pF AVERAGE FORWARD RECTIFIED CURRENT, AMPERES FIG.1 - FORWARD CURRENT DERATING CURVE 100 10 1 0.1 0.01 0.1 1 t, PULSE DURATION, sec. 10 100