TS79M00A Series 3-Terminal 500mA Negative Voltage Regulator TO-220 TO-252 (DPAK) Pin Definition: 1. Input 2. Ground (tab) 3. Output General Description The TS79M00A series of fixed output negative voltage regulators are intended as complements to the popular TS78M00A series device. These negative regulators are available in the same seven-voltage options as the TS7900A devices. In addition, one extra voltage option commonly employed in MECL systems is also available in the negative TS79M00A Series. Available in fixed output voltage options from -5.0 to -24 volts, these regulators employ current limiting, thermal shutdown, and safe-area compensation--making them remarkably rugged under most operating conditions. With adequate heat sinking they can deliver output currents in excess of 0.5 ampere. This series is offered in 3-pin TO-220 & TO-252 package. Features Standard Application Circuit ● Output Voltage Range -5 to -24V ● Output current up to 0.5A ● No external components required ● Internal thermal overload protection ● Internal short-circuit current limiting ● Output transistor safe-area compensation ● Output voltage offered in 2% tolerance A common ground is required between the input and the output voltages. The input voltage must remain typically 2.0V above the output voltage even during the low point on the Input ripple voltage. XX = these two digits of the type number indicate voltage. * = Cin is required if regulator is located an appreciable distance from power supply filter. ** = Co is not needed for stability; however, it does improve transient response. Ordering Information Part No. Package Packing TS79MxxACZ C0 TO-220 50pcs / Tube TS79MxxACP RO TO-252 2.5Kpcs / 13” Reel Note: Where xx denote voltage option Absolute Maximum Rating (Ta = 25oC unless otherwise noted) Parameter Symbol Limit Unit Input Voltage VIN* -35 V Input Voltage VIN** -40 V PD Internal Limited Power Dissipation Operating Junction Temperature TJ Storage Temperature Range Note: * TS79M05A to TS79M18A ** TS79M24A *** Follow the derating curve TSTG 1/10 W 0~+125 o -65~+150 o C C Version: A07 TS79M00A Series 3-Terminal 500mA Negative Voltage Regulator TS79M05A Electrical Characteristics o o (Vin= -10V, Iout=350mA, 0 C≤Tj≤125 C, Cin=0.33uF, Cout=0.1uF; unless otherwise specified.) Parameter Symbol Test Condition o Tj=25 C Output voltage Vout Line Regulation REGline Load Regulation REGload Quiescent Current Iq Quiescent Current Change ΔIq Output Noise Voltage Ripple Rejection Ratio Voltage Drop Peak Output Current Temperature Coefficient of Output Voltage Vn RR Vdrop Io peak ΔVout/ ΔTj -7.5V≤Vin≤-20V, 5mA≤Iout≤500mA, PD≤5W -7.5V≤Vin≤-25V o Tj=25 C -8V≤Vin≤-18V 5mA≤Iout≤500mA o Tj=25 C 250mA≤Iout≤200mA o Iout=0, Tj=25 C -7.5V≤Vin≤-25V 5mA≤Iout≤500mA o 10Hz≤f≤100KHz, Tj=25 C f=120Hz, -8V≤Vin≤-18V o Iout=500mA, Tj=25 C o Tj=25 C o o Iout=5mA, 0 C≤Tj≤125 C Min Typ Max Unit -4.90 -5 -5.10 -4.85 -5 -5.15 --------54 --- 7 2 20 10 4 --40 66 2 0.7 50 30 100 50 8 1 0.5 ----- -- -0.1 -- mV/ C Unit V mV mA µV dB V A o TS79M06A Electrical Characteristics o o (Vin= -11V, Iout=350mA, 0 C≤Tj≤125 C, Cin=0.33uF, Cout=0.1uF; unless otherwise specified.) Parameter Symbol Test Condition Min Typ Max Tj=25 C -8.5V≤Vin≤-21V, 5mA≤Iout≤500mA, PD≤5W -8.5V≤Vin≤-25V o Tj=25 C -9V≤Vin≤-13V 5mA≤Iout≤500mA o Tj=25 C 250mA≤Iout≤200mA o Iout=0, Tj=25 C -8.5V≤Vin≤-25V 5mA≤Iout≤500mA o 10Hz≤f≤100KHz, Tj=25 C f=120Hz, -9V≤Vin≤-19V o Iout=500mA, Tj=25 C o Tj=25 C -5.88 -6 -6.12 -5.76 -6 -6.24 --------60 --- 5 1.5 14 4 4 --44 73 2 0.7 120 60 120 60 8 1 0.5 ----- o Output Voltage Vout Line Regulation REGline Load Regulation Quiescent Current Quiescent Current Change REGload Iq ΔIq V mV mA Output Noise Voltage Vn uV Ripple Rejection Ratio RR dB Voltage Drop Vdrop V Peak Output Current Io peak A Temperature Coefficient of o o o ΔVout/ ΔTj Iout=5mA, 0 C≤Tj≤125 C --0.1 -mV/ C Output Voltage Pulse testing techniques are used to maintain the junction temperature as close to the ambient temperature as possible, and thermal effects must be taken into account separately. This specification applies only for DC power dissipation permitted by absolute maximum ratings. 2/10 Version: A07 TS79M00A Series 3-Terminal 500mA Negative Voltage Regulator TS79M08A Electrical Characteristics o o Vin= -14V, Iout=350mA, 0 C≤Tj≤125 C, Cin=0.33uF, Cout=0.1uF; unless otherwise specified.) Parameter Symbol Test Condition o Tj=25 C Output voltage Vout Line Regulation REGline Load Regulation REGload Quiescent Current Iq Quiescent Current Change ΔIq Output Noise Voltage Ripple Rejection Ratio Voltage Drop Peak Output Current Temperature Coefficient of Output Voltage Vn RR Vdrop Io peak ΔVout/ ΔTj -10.5V≤Vin≤-23V, 5mA≤Iout≤500mA, PD≤5W -10.5V≤Vin≤-25V o Tj=25 C -11V≤Vin≤-17V 5mA≤Iout≤500mA o Tj=25 C 250mA≤Iout≤200mA o Iout=0, Tj=25 C 10.5V≤Vin≤25V 5mA≤Iout≤500mA o 10Hz≤f≤100KHz, Tj=25 C f=120Hz, 11V≤Vin≤21V o Iout=500mA, Tj=25 C o Tj=25 C o o Iout=5mA, 0 C≤Tj≤125 C Min Typ Max Unit -7.84 -8 -8.16 -7.68 -8 -8.32 --------56 --- 6 2 12 4 4.3 --52 72 2 0.7 160 80 160 80 8 1 0.5 ----- -- -1 -- mV/ C Unit V mV mA µV dB V A o TS79M09A Electrical Characteristics o o (Vin= -15V, Iout=350mA, 0 C≤Tj≤125 C, Cin=0.33uF, Cout=0.1uF; unless otherwise specified.) Parameter Symbol Test Condition Min Typ Max Tj=25 C -11.5V≤Vin≤-23V, 5mA≤Iout≤500mA, PD≤5W -11.5V≤Vin≤-26V o Tj=25 C -12V≤Vin≤-17V 5mA≤Iout≤500mA o Tj=25 C 250mA≤Iout≤200mA o Iout=0, Tj=25 C -11.5V≤Vin≤-26V 5mA≤Iout≤500mA o 10Hz≤f≤100KHz, Tj=25 C f=120Hz, -12V≤Vin≤-22V o Iout=500mA, Tj=25 C o Tj=25 C -8.82 -9 -9.18 -8.64 -9 -9.36 --------56 --- 6 2 12 4 4.3 --58 71 2 0.7 180 90 180 90 8 1 0.5 ----- o Output Voltage Vout Line Regulation REGline Load Regulation Quiescent Current Quiescent Current Change REGload Iq ΔIq V mV mA Output Noise Voltage Vn uV Ripple Rejection Ratio RR dB Voltage Drop Vdrop V Peak Output Current Io peak A Temperature Coefficient of o o o ΔVout/ ΔTj Iout=5mA, 0 C≤Tj≤125 C --1 -mV/ C Output Voltage Pulse testing techniques are used to maintain the junction temperature as close to the ambient temperature as possible, and thermal effects must be taken into account separately. This specification applies only for DC power dissipation permitted by absolute maximum ratings. 3/10 Version: A07 TS79M00A Series 3-Terminal 500mA Negative Voltage Regulator TS79M12A Electrical Characteristics o o (Vin= -19V, Iout=350mA, 0 C≤Tj≤125 C, Cin=0.33uF, Cout=0.1uF; unless otherwise specified.) Parameter Symbol Test Condition o Tj=25 C Output voltage Vout Line Regulation REGline Load Regulation REGload Quiescent Current Iq Quiescent Current Change ΔIq Output Noise Voltage Ripple Rejection Ratio Voltage Drop Peak Output Current Temperature Coefficient of Output Voltage Vn RR Vdrop Io peak ΔVout/ ΔTj -14.5V≤Vin≤-27V, 5mA≤Iout≤500mA, PD ≤5W -14.5V≤Vin≤-30V o Tj=25 C -15V≤Vin≤-19V 5mA≤Iout≤500mA o Tj=25 C 250mA≤Iout≤200mA o Tj=25 C, Iout=0 -14.5V≤Vin≤-30V 5mA≤Iout≤500mA o 10Hz≤f≤100KHz, Tj=25 C f=120Hz, -15V≤Vin≤-25V o Iout=500mA, Tj=25 C o Tj=25 C o o Iout=5mA, 0 C≤Tj≤125 C Min Typ Max Unit -11.76 -12 -12.24 -11.52 -12 -12.48 --------55 --- 10 3 12 4 4.3 --75 70 2 2.1 240 120 240 120 8 1 0.5 ----- -- -1 -- mV/ C Unit V mV mA µV dB V A o TS79M15A Electrical Characteristics o o Vin= -23V, Iout=350mA, 0 C≤Tj≤125 C, Cin=0.33uF, Cout=0.1uF; unless otherwise specified.) Parameter Symbol Test Condition Min Typ Max Tj=25 C -17.5V≤Vin≤-30V, 5mA≤Iout≤500mA, PD ≤5W -17.5V≤Vin≤-30V o Tj=25 C -18V≤Vin≤-22V 5mA≤Iout≤500mA o Tj=25 C 250mA≤Iout≤200mA o Tj=25 C, Iout=0 -17.5V≤Vin≤-30V 5mA≤Iout≤500mA o 10Hz≤f≤100KHz, Tj=25 C f=120Hz, -18V≤Vin≤-28V o Iout=500mA, Tj=25 C o Tj=25 C -14.70 -15 -15.30 -14.40 -15 -15.60 --------54 --- 12 3 12 4 4.3 --90 69 2 0.7 300 150 300 150 8 1 0.5 ----- o Output Voltage Vout Line Regulation REGline Load Regulation Quiescent Current Quiescent Current Change REGload Iq ΔIq V mV mA Output Noise Voltage Vn uV Ripple Rejection Ratio RR dB Voltage Drop Vdrop V Peak Output Current Io peak A Temperature Coefficient of o o o ΔVout/ ΔTj Iout=5mA, 0 C≤Tj≤125 C --1 -mV/ C Output Voltage Pulse testing techniques are used to maintain the junction temperature as close to the ambient temperature as possible, and thermal effects must be taken into account separately. This specification applies only for DC power dissipation permitted by absolute maximum ratings. 4/10 Version: A07 TS79M00A Series 3-Terminal 500mA Negative Voltage Regulator TS79M18A Electrical Characteristics o o (Vin= -24V, Iout=350mA, 0 C≤Tj≤125 C, Cin=0.33uF, Cout=0.1uF; unless otherwise specified.) Parameter Symbol Test Condition o Tj=25 C Output voltage Vout Line Regulation REGline Load Regulation REGload Quiescent Current Iq Quiescent Current Change ΔIq Output Noise Voltage Ripple Rejection Ratio Voltage Drop Peak Output Current Temperature Coefficient of Output Voltage Vn RR Vdrop Io peak ΔVout/ ΔTj -21V≤Vin≤-33V, 5mA≤Iout≤500mA, PD ≤5W -21V≤Vin≤-33V o Tj=25 C -22V≤Vin≤-26V 5mA≤Iout≤500mA o Tj=25 C 250mA≤Iout≤200mA o Iout=0, Tj=25 C -21V≤Vin≤-33V 5mA≤Iout≤500mA o 10Hz≤f≤100KHz, Tj=25 C f=120Hz, -21V≤Vin≤-31V o Iout=500mA, Tj=25 C o Tj=25 C o o Iout=5mA, 0 C≤Tj≤125 C Min Typ Max Unit -17.64 -18 -18.36 -17.28 -18 -18.72 --------53 --- 15 5 12 4 4.5 --110 68 2 0.7 360 180 360 180 8 1 0.5 ----- -- -1 -- mV/ C Unit V mV mA µV dB V A o TS79M24A Electrical Characteristics o o Vin= -33V, Iout=350mA, 0 C≤Tj≤125 C, Cin=0.33uF, Cout=0.1uF; unless otherwise specified.) Parameter Symbol Test Condition Min Typ Max Tj=25 C -27V≤Vin≤-38V, 5mA≤Iout≤500mA, PD ≤5W -27V≤Vin≤-38V o Tj=25 C -28V≤Vin≤-32V 5mA≤Iout≤500mA o Tj=25 C 250mA≤Iout≤200mA o Iout=0, Tj=25 C -27V≤Vin≤-38V 5mA≤Iout≤500mA o 10Hz≤f≤100KHz, Tj=25 C f=120Hz, -27V≤Vin≤-37V o Iout=500mA, Tj=25 C o Tj=25 C -23.52 -24 -24.48 -23.07 -24 -25.96 --------50 --- 18 6 12 4 4.6 --170 65 2 0.7 480 240 480 240 8 1 0.5 ----- o Output Voltage Vout Line Regulation REGline Load Regulation REGload Quiescent Current Quiescent Current Change Iq ΔIq V mV mA Output Noise Voltage Vn uV Ripple Rejection Ratio RR dB Voltage Drop Vdrop V Peak Output Current Io peak A Temperature Coefficient of o o o ΔVout/ ΔTj Iout=5mA, 0 C≤Tj≤125 C --1 -mV/ C Output Voltage Pulse testing techniques are used to maintain the junction temperature as close to the ambient temperature as possible, and thermal effects must be taken into account separately. This specification applies only for DC power dissipation permitted by absolute maximum ratings. . 5/10 Version: A07 TS79M00A Series 3-Terminal 500mA Negative Voltage Regulator Electrical Characteristics Curve Figure 1. Worse Case Power Dissipation vs. Ambient Temperature (TO-220) Figure 2. Peak Output Current as a Function of Input-Output Differential Voltage Figure 3. Bias Current vs. Input Voltage Figure 4. Bias Current vs. Output Current Figure 5. Ripple Rejection vs. Frequency Figure 6. Ripple Rejection vs. Output Voltage 6/10 Version: A07 TS79M00A Series 3-Terminal 500mA Negative Voltage Regulator Application information Figure 7. DPAK Thermal Resistance and Maximum Power Dissipation vs. P.C.B Copper Length 7/10 Version: A07 TS79M00A Series 3-Terminal 500mA Negative Voltage Regulator TO-220 Mechanical Drawing DIM A B C D E F G H I J K L M N O P TO-220 DIMENSION MILLIMETERS INCHES MIN MAX MIN MAX 10.000 10.500 0.394 0.413 3.740 3.910 0.147 0.154 2.440 0.381 2.345 4.690 12.700 8.382 14.224 3.556 0.508 27.700 2.032 0.255 5.842 2.940 6.350 1.106 2.715 5.430 14.732 9.017 16.510 4.826 1.397 29.620 2.921 0.610 6.858 0.096 0.015 0.092 0.092 0.500 0.330 0.560 0.140 0.020 1.060 0.080 0.010 0.230 0.116 0.250 0.040 0.058 0.107 0.581 0.355 0.650 0.190 0.055 1.230 0.115 0.024 0.270 Marking Diagram XX Y M L CZ = Output Voltage (05=-5V, 06=-6V, 08=-8V, 09=-9V, 12=-12V, 15=-15V, 18=-18V, 24=-24V) = Year Code = Month Code (A=Jan, B=Feb, C=Mar, D=Apl, E=May, F=Jun, G=Jul, H=Aug, I=Sep, J=Oct, K=Nov, L=Dec) = Lot Code = Package Code for TO-220 8/10 Version: A07 TS79M00A Series 3-Terminal 500mA Negative Voltage Regulator TO-252 Mechanical Drawing DIM A A1 B C D E F G G1 G2 H I J K L M TO-252 DIMENSION MILLIMETERS INCHES MIN MAX MIN MAX 2.3BSC 0.09BSC 4.6BSC 0.18BSC 6.80 7.20 0.268 0.283 5.40 5.60 0.213 0.220 6.40 6.65 0.252 0.262 2.20 2.40 0.087 0.094 0.00 0.20 0.000 0.008 5.20 5.40 0.205 0.213 0.75 0.85 0.030 0.033 0.55 0.65 0.022 0.026 0.35 0.65 0.014 0.026 0.90 1.50 0.035 0.059 2.20 2.80 0.087 0.110 0.50 1.10 0.020 0.043 0.90 1.50 0.035 0.059 1.30 1.70 0.051 0.67 Marking Diagram XX Y M L CP = Output Voltage (05=-5V, 06=-6V, 08=-8V, 09=-9V, 12=-12V, 15=-15V, 18=-18V, 24=-24V) = Year Code = Month Code (A=Jan, B=Feb, C=Mar, D=Apl, E=May, F=Jun, G=Jul, H=Aug, I=Sep, J=Oct, K=Nov, L=Dec) = Lot Code = Package Code for TO-252 9/10 Version: A07 TS79M00A Series 3-Terminal 500mA Negative Voltage Regulator Notice Specifications of the products displayed herein are subject to change without notice. TSC or anyone on its behalf, assumes no responsibility or liability for any errors or inaccuracies. Information contained herein is intended to provide a product description only. No license, express or implied, to any intellectual property rights is granted by this document. Except as provided in TSC’s terms and conditions of sale for such products, TSC assumes no liability whatsoever, and disclaims any express or implied warranty, relating to sale and/or use of TSC products including liability or warranties relating to fitness for a particular purpose, merchantability, or infringement of any patent, copyright, or other intellectual property right. The products shown herein are not designed for use in medical, life-saving, or life-sustaining applications. Customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify TSC for any damages resulting from such improper use or sale. 10/10 Version: A07